Structural and magnetic properties of Pr3(Fe1−xCox)27.5Ti1.5 (x=0.0, 0.1, 0.2, 0.3)

A novel class of Co-substituted 3 : 29 materials, Pr₃(Fe_1−xCo_x)_27.5Ti_1.5 (x=0, 0.1, 0.2, 0.3) have been synthesized. Rietveld analysis of X-ray powder diffraction patterns for the x=0, 0.1 and 0.2 compositions showed that nearly all of the compounds are formed in monoclinic symmetry, with A2/m space group with traces of α-Fe, whereas, in x=0.3, additional traces of a (Co/Fe)–Ti (1 : 12) phase are also seen. The saturation magnetization increases with Co concentration both at 5 and 300 K and is explained on the basis of a rigid band model. A magnetic transition is observed for x=0.1 near 240 K. A large increase in Curie temperature, of about 180 K for x=0.1 and about 110 K for the other concentrations, is discussed on the basis of the strengthening of TM–TM exchange by the preferential occupation of Co in some of the Fe sites originally participating in antiferromagnetic bonds.     

Corrosion behavior of Nd9.4Pr0.6Febal.Co6B6Ga0.5TixCx (x=0, 1.5, 3, 6) nanocomposites annealed melt-spun ribbons

The effect of Ti and C additions on the corrosion behavior of Nd_9.4Pr_0.6Fe_bal.Co₆B₆Ga_0.5Ti_xC_x (x=0, 1.5, 3, 6) isotropic nanocomposite melt-spun ribbons in 3.5 wt% sodium chloride solution was studied. The melt-spun ribbons were annealed at 750 °C for 10 min in argon-filled quartz capsules. The microstructure of multiphase nanocrystalline samples and corrosion products was characterized using the X-ray diffraction and electron microscopy techniques. The electrochemical behavior was assessed using potentiodynamic polarization and electrochemical impedance spectroscopy. The results show that the addition of Ti and C increases the corrosion resistance of NdFeB ribbons; the best corrosion resistance was obtained for 1.5 wt% Ti and C content.     

Preparation of substituted barium ferrite BaFe12−x(Ti0.5Co0.5)xO19 by citrate precursor method and compositional dependence of their magnetic properties

As a possible candidate for the left-handed metamaterial with negative permeability, a series of Ti, Co-substituted M-type barium hexaferrite BaFe_12−x(Ti_0.5Co_0.5)_xO₁₉ (x=0, 1, 2, 3, 4 and 5) was prepared by citrate precursor method. The formation processes of the substituted barium hexaferrite compounds from the precursors were followed by the measurements of powder X-ray diffraction (XRD), Infrared absorption spectra (FT-IR), and thermogravimetry and differential thermal analysis (TG/DTA) coupled with mass spectroscopy (MS). In the case of the non-substituted sample, the formation of the barium hexaferrite is regulated by the thermal decomposition of BaCO₃ and the solid-state reactions of BaO and Fe₂O₃ in the temperature range from 800 to 1100 K. The formation temperature of the substituted BaFe_12−x(Ti_0.5Co_0.5)_xO₁₉ is higher than that for the non-substituted sample and increases with the value of x, due to the effects of carbonate ions incorporated by the partial substitution of Fe³⁺ by (Ti_0.5Co_0.5)³⁺. On heating up to ca. 1200 K, all the substituted samples transform into the magenetoplumbite phase as is the non-substituted sample. The compositional dependence of the magnetic properties of the substituted barium hexaferrite was investigated by the magnetization measurement. The decrease in the magnetic anisotropy was confirmed by the change in the magnetization curve and coercivity H_C with the composition x. A negative permeability spectrum was observed in the BaFe₉(Ti_0.5Co_0.5)₃O₁₉ in the frequency range from 2 to 4 GHz.     

Crystallographic and magnetic properties of (Nd,Dy)3Fe27.5(Ti,Mo)1.5 compounds

A systematic study of the formation, structure and magnetic properties of (Nd,Dy)₃Fe_27.5(Ti,Mo)_1.5 compounds has been performed. Rietveld analyses of the X-ray patterns of the samples indicate that the concentrations of Ti and Mo affect the formation and structural properties slightly, whereas different rare-earth (Nd and Dy) contents influence them significantly. It is found that high Dy contents make it difficult to form the 3:29-type structures. The Curie temperatures of Nd_2.1Dy_0.9Fe_27.5Ti_1.5−xMo_x decrease monotonically as more Ti was replaced by Mo but their saturation magnetizations remain almost unchanged; in contrast, for Nd_3−yDy_yFe_27.5TiMo_0.5, their saturation magnetizations decrease monotonically with increasing Dy contents while their Curie temperatures are constant.     

Synthesis,structures and magnetic properties of Pr-lean Pr2Fe14B/Fe3B nanocomposite alloys

The lean rare-earth Pr_4.5Fe_77−xTi_xB_18.5 (x=0, 1, 4, 5) nanocomposite alloys were prepared by melt spinning method and subsequent thermal annealing. The effect of Ti content and annealing temperature on the magnetic properties and the microstructure of these magnets were investigated. The enhancing coercivity H_c from 211.4 to 338.2 kA/m has been observed at the optimal annealing temperature of 700 °C by the addition of 5 at% Ti in Pr₂Fe₁₄B/Fe₃B alloys. It was also found that increasing Ti content leads to marked grain refinement in the annealed alloys, resulting in strong exchange-coupling interaction between the hard and the soft phases in these ribbons. In addition, the magnetization reversal behaviors of Pr₂Fe₁₄B/Fe₃B nanocomposites were discussed in detail.     

High magnetostriction at low fields of (Tb1−xDyx)0.2Pr0.8(Fe0.4Co0.6)1.88C0.05 intermetallic compounds

The structure and magnetostriction of the (Tb_1−xDy_x)_0.2Pr_0.8(Fe_0.4Co_0.6)_1.88C_0.05 intermetallic compounds (0≤x≤1) were studied by X-ray diffraction and magnetic measurements. The formation of an approximate single Laves phase with a MgCu2-type cubic structure was observed in this series of compounds. It was found that the Curie temperature and the saturation magnetization of the compounds would decrease with increase in the Dy content up to x=1. The magnetostriction λ_a (λ_a=λ_‖-λ_⊥) gently rises when x≤0.6, and follows with a precipitous fall when x exceeds 0.6, with the highest value of λ_a being reached in the compounds with x=0.6. The magnetostriction of all the samples was observed to approach their own saturation in the magnetic fields higher than 4 kOe. This indicates that the addition of a small amount of Dy could effectively improve the low-field magnetostriction of the Tb_0.2Pr_0.8(Fe_0.4Co_0.6)_1.88C_0.05 compounds, which could become a kind of promising magnetostrictive material.     

Hard magnetic properties of melt-spun Co82Zr18−xTix alloys

The phases and magnetic properties of Co-Zr-Ti melt-spun ribbons were studied by XRD analysis and magnetic measurements. The optimal magnetic properties of Ms=59.0 emu/g, Mr=4.0 kG, Hc=2.9 kOe, and (BH)_max=3.0 MGOe were obtained in Co₈₂Zr₁₄Ti₄ ribbons produced at a wheel speed of 30 m/s. In this work, we found that Ti was one of the few large atomic radius elements, which could improve hard magnetic properties of Co-Zr alloy.     

Half-metallic properties of the Co2Ti1−xFexGa Heusler alloys and Co2Ti0.5Fe0.5Ga (0 0 1) surface

Electronic and magnetic properties of the bulk Co₂Ti_1−xFe_xGa Heusler alloys and Co₂Ti_0.5Fe_0.5Ga (0 0 1) surfaces are studied within the framework of density functional theory using the augmented plane wave plus local orbital (APW+lo) approach. It will be shown that all alloys have the spin polarization of the ideal 100% value except the Co₂FeGa alloy with spin polarization about 98%. Co₂Ti_0.5Fe_0.5Ga is an example that is stable against the effects destroying the half-metallicity due to the position of the Fermi energy (E_F) in the middle of the minority band gap. The phase diagram obtained by ab-initio atomistic thermodynamics shows that in the higher limit of μ_Ga three surfaces of FeGa, TiGa and TiFeGa are accessible in the Co₂Ti_0.5Fe_0.5Ga alloy but on decreasing μ_Ga, the accessible region gradually moves towards FeGa termination. It is discussed that, at the ideal surfaces, half-metallicity of the alloy is lost, although the TiGa surface keeps high spin polarization (about 95%).     

Effect of monovalent metal substitution on the magnetocaloric effect of perovskite manganites Pr0.5Sr0.3M0.2MnO3 (M=Na,Li, K and Ag)

The influence of monovalent doping on the magnetocaloric effect (MCE) and refrigerant capacity or relative cooling power (RCP) of Pr_0.5Sr_0.3M_0.2MnO₃ (M=Na, Li, K and Ag) materials has been investigated. A large magnetocaloric effect was inferred over a wide range of temperature around the second order paramagnetic–ferromagnetic transition. The maximum magnetic entropy changes (ΔS_M) reached 1.8, 2.2, 1.6 and 2.1 J/kg K and the relative cooling power (RCP) approached 58.9, 59.3, 69.6 and 54.6 J/kg for Na, Li, K and Ag doped materials in the magnetic change of 15 kOe, respectively. According to the results determined by the Maxwell relation, the magnetic entropy change fits well with the Landau theory of phase transition above T_C for Pr_0.5Sr_0.3Li_0.2MnO₃. The large magnetic entropy change induced by low magnetic field suggested that these materials are beneficial for practical applications.     

Crystal chemistry of layered carbide, Ti3(Si0.43Ge0.57)C2

 The crystal structure of a layered ternary carbide, Ti₃(Si_0.43Ge_0.57)C₂, was studied with single-crystal X-ray diffraction. The compound has a hexagonal symmetry with space group P6₃/mmc and unit-cell parameters a=3.0823(1) Å, c=17.7702(6) Å, and V=146.21(1) Å³. The Si and Ge atoms in the structure occupy the same crystallographic site surrounded by six Ti atoms at an average distance of 2.7219 Å, and the C atoms are octahedrally coordinated by two types of symmetrically distinct Ti atoms, with an average C-Ti distance of 2.1429 Å. The atomic displacement parameters for C and Ti are relatively isotropic, whereas those for A (=0.43Si+0.57Ge) are appreciably anisotropic, with U₁₁ (=U₂₂) being about three times greater than U₃₃. Compared to Ti₃SiC₂, the substitution of Ge for Si results in an increase in both A-Ti and C-Ti bond distances. An electron density analysis based on the refined structure shows that each A atom is bonded to 6Ti atoms as well as to its 6 nearest neighbor A site atoms, whether the site is occupied by Si or Ge, suggesting that these bond paths may be significantly involved with electron transport properties.     

A study on magnetoelastic properties of Tb3 (Fe28−xCox) V1.0 (x=0, 3, 6) compounds

In this work, The magnetoelastic properties of polycrystalline samples of Tb₃ (Fe_28−xCo_x) V_1.0 (x=0, 3, 6) intermetallic compounds are investigated by means of linear thermal expansion and magnetostriction measurements in the temperature range of 77–515 K under applied magnetic fields up to 1.5 T. The linear thermal expansion increases with the Co content. The well-defined anomalies observed in the linear thermal expansion coefficients for Tb₃ (Fe_28−xCo_x) V_1.0 (x=0, 3, 6) compounds are associated with the magnetic ordering temperature for x=0 and spin reorientation temperatures for x=3, 6. Below transition temperatures, the value of the longitudinal magnetostriction (λ_Pa) at 1.6 T increases with Co content.     

Anisotropy and FOMP in Tb3 (Fe28−xCox) V1.0 (x=0, 3 and 6) compounds

In this work, the structural and magnetic properties of Tb₃ (Fe_28−xCo_x) V_1.0 (x=0, 3, 6) compounds have been investigated. The structural characterization of compounds by X-ray powder diffraction is an evidence for a monoclinic Nd₃(Fe, Ti)₂₉-type structure (A2/m space group). The refined lattice parameters a and b (but not c) and the unit cell volume V, obtained from the XRD data by the Rietveld method, are found to decrease with increasing Co concentration. The unit cell parameters behavior has been attributed to the smaller Co atoms and a preferential substitution of Fe by Co. The anisotropy field (H_a) as well as critical field (H_cr) was measured using the singular point detection (SPD) technique from 5 to 300 K in a pulsed magnetic field of up to 30 T. At T=5 K, a FOMP of type 2 was observed for all samples and persists at all temperatures up to 300 K. For sample x=0, H_cr=10.6 and 2.0 T at 5 and 300 K, respectively, is equal to that reported earlier. The occurrence of canting angles between the magnetic sublattices during the magnetization process instead of high-order anisotropy contributions (at room temperature are usually negligible) has been considered to explain the survival of the FOMP at room temperature. The anisotropy and critical fields behave differently for samples with x=0, 3 compared with x=6. The observed behavior has been related to the fact that the Co substitution for Fe takes place with a preferential entrance in the inequivalent crystallographic sites of the 3:29 structure. The contribution of the Tb-sublattice in the Tb₃(Fe, V)₂₉ compound with uniaxial anisotropy has been scaled from the anisotropy field measured on a Y₃(Fe, V)₂₉ single crystal with easy plane anisotropy.     

Structure and magnetic properties of (Nd,Dy)16(Fe,Co)76−xTixB8 powders prepared by mechanical alloying

Nanocrystalline (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ magnets were prepared by mechanical alloying and respective heat treatment at 973–1073 K/30–60 min. An addition of 0.5 at % of Ti results in an increase of coercivity from 796 to 1115 kA m⁻¹. Partial substitution of Nd by Dy results in an additional increase of coercivity up to 1234 kA m⁻¹. Mössbauer investigations shows that for x?1 the (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ powders are single phase. For higher Ti contents (x>1) the mechanically alloyed powders heat treated at 973 K are no more single phase, and the coercivity decreases due to the presence of an amorphous phase. A heat treatment at a higher temperature (1073 K) for longer time (1 h) results in the full recrystallisation of powders. The mean hyperfine field of the Nd₂Fe₁₄B phase decreases for titanium contents of 0?x?1, and remains constant for x>1. This indicates that the Ti content in the Nd₂Fe₁₄B phase reaches its maximum value.     

Synthesis and magnetic properties of Pr(Fe 1-xCo x) 2 and Pr 1-yTb y(Fe 0.4Co 0.6) 2 alloys

Measurement of X-ray diffraction, magnetization and magnetostriction was made on the Pr(Fe_1-xCo_x)₂ (x=0.4, 0.5 and 0.6) and Pr_1-yTb_y(Fe_0.4Co_0.6)₂ (y=0, 0.1, 0.2 and 0.3) alloy series. It was found that a cubic phase with the MgCu₂ structure can be obtained in the Pr(Fe_1-xCo_x)₂ series only at x=0.6. The Pr_1-yTb_y(Fe_0.4Co_0.6)₂ system has the cubic MgCu₂ structure over the studied range for y. The lattice constant and magnetization decrease and the Curie temperature increases with increasing y. At 7 K, Pr_1-yTb_y(Fe_0.4Co_0.6)₂ samples are found to have huge intrinsic coercivities, which are associated with narrow domain walls. It is also found from X-ray measurement that in Pr_1-yTb_y(Fe_0.4Co_0.6)₂ the spontaneous magnetostriction ₁₁₁ increases due to Tb substitution, while the saturation magnetostriction _s is much lower than ₁₁₁. This can be attributed to the large value of ₁₀₀ with an opposite sign to ₁₁₁, which may be caused by the filling of the d band due to Co substitution. PACS 75.80.-g; 61.10.-i; 75.60.-d     

Preparation and magnetic properties of the conductive Co(1−x)NixFe2O4/polyaniline microsphere composites

Core-shell Co_(1−x)Ni_xFe₂O₄/polyaniline nanoparticles, where the core was Co_(1−x)Ni_xFe₂O₄ and the shell was polyaniline, were prepared by the combination of sol-gel process and in-situ polymerization methods. Nanoparticles were investigated by Fourier transform spectrometer, X-ray diffraction diffractometer, Scanning electron microscope, Differential thermal analysis and Superconductor quantum interference device. The results showed that the saturation magnetization of pure Co_(1−x)Ni_xFe₂O₄ nanoparticles were 57.57 emu/g, but Co_(1−x)Ni_xFe₂O₄/polyaniline composites were 37.36 emu/g. It was attributed to the lower content (15 wt%), smaller size and their uneven distribution of Co_(1−x)Ni_xFe₂O₄ nanoparticles in the final microsphere composites. Both Co_(1−x)Ni_xFe₂O₄ and PANI/Co_(1−x)Ni_xFe₂O₄ showed superparamagnetism.     

Magnetic properties, microstructures and magnetoresistance effect in Co/Alq3 granular films

A series of Co_x(Alq₃)_1−x granular films were prepared using the co-evaporating technique. HRTEM images show typical characteristics of granular films with the average size of 2-5 nm. It shows a gradual change from superparamagnetism to ferromagnetism with the rise of x. Negative magnetoresistance (MR) was observed, reaching −5.31% in x=0.44 sample at 30 K under the field of 10 kOe. The concentration dependence of MR and resistivity is also investigated. The inter-particle tunneling is believed to account for the negative MR effect.     

Structure,magnetic properties and magnetostriction of laves compounds Nd1−xPrx(Fe0.35Co0.55B0.1)2

The C15 Laves phases with composition Nd_1−xPr_x(Fe_0.35Co_0.55B_0.1)₂ (0?x?1) have been synthesized by arc melting and subsequent annealing. The Curie temperature T_c and the saturation magnetizations M_s at 5 and 295 K decrease with increasing Pr content. The linear anisotropic magnetostriction λ_a=λ_∥−λ_⊥ at room temperature for Nd_1−xPr_x(Fe_0.35Co_0.55B_0.1)₂ alloys with 0?x?0.4 initially reaches a negative minimum, then increases and changes its sign with increasing magnetic field H, and the λ_a for the alloys with x?0.6 is positive and increases as magnetic field H increases.     

Influence of mobile space charges on electrical properties of ferroelectric Bi3.5La0.5Ti3O12 thin films

Lanthanum-substituted bismuth titanate, Bi_3.5La_0.5Ti₃O₁₂ (i.e., x=0.5 in Bi_4−xLa_xTi₃O₁₂), thin films have been grown on Pt/Ti/SiO₂/Si substrates using pulsed laser deposition. The frequency dependence of the real part ε′(ω) and the imaginary part ε″(ω) of the dielectric constant has been studied. The ε′(ω) does not show any sudden change within the frequency range of 10²-10⁶ Hz. In contrast, the ε″(ω) shows a large dispersion as frequency decreases. The observed relaxation behavior in ε″(ω) can be explained in terms of a migration of oxygen vacancies in (Bi₂O₂)²⁺ layers, not in Bi₂Ti₃O₁₀ perovskite layers.     

The effect of different temperature annealing on phase relation of LaFe11.5Si1.5 and the magnetocaloric effects of La0.8Ce0.2Fe11.5−xCoxSi1.5 alloys

The phase relation of LaFe_11.5Si_1.5 alloys annealed at different high-temperature from 1223 K (5 h) to 1673 K (0.5 h) has been studied. The powder X-ray diffraction (XRD) patterns show that large amount of 1:13 phase begins to form in the matrix alloy consisting of α-Fe and LaFeSi phases when the annealing temperature is 1423 K. In the temperature range from 1423  to 1523 K, α-Fe and LaFeSi phases rapidly decrease to form 1:13 phase, and LaFeSi phase is rarely observed in the XRD pattern of LaFe_11.5Si_1.5 alloy annealed at 1523 K. With annealing temperature increasing from 1573  to 1673 K, the LaFeSi phase is detected again in the LaFe_11.5Si_1.5 alloy, and there is La₅Si₃ phase when the annealing temperature reaches 1673 K. There almost is no change in the XRD patterns of LaFe_11.5Si_1.5 alloys annealed at 1523 K for 3-5 h. According to this result, the La_0.8Ce_0.2Fe_11.5−xCo_xSi_1.5 (0≤×≤0.7) alloys are annealed at 1523 K (3 h). The analysis of XRD patterns shows that La_0.8Ce_0.2Fe_11.5xCo_xSi_1.5 alloys consist of the NaZn₁₃-type main phase and α-Fe impurity phase. With the increase of Co content from x=0 to 0.7, the Curie temperature T_C increases from 180 to 266 K. Because the increase of Co content can weaken the itinerant electron metamagnetic transition, the order of the magnetic transition at T_C changes from first to second-order between x=0.3 and 0.5. Although the magnetic entropy change decreases from 34.9 to 6.8 J/kg K with increasing Co concentration at a low magnetic field of 0-2 T, the thermal and magnetic hysteresis loss reduces remarkably, which is very important for the magnetic refrigerant near room temperature.     

Magnetoelectric characterization of xNi0.75Co0.25Fe2O4-(1−x)BiFeO3 nanocomposites

Magnetoelectric (ME) nanocomposites containing Ni_0.75Co_0.25Fe₂O₄-BiFeO₃ phases were prepared by citrate sol-gel process. X-ray diffraction (XRD) analysis showed phase formation of xNi_0.75Co_0.25Fe₂O₄-(1−x)BiFeO₃ (x=0.1, 0.2, 0.3 and 0.4) composites on heating at 700 °C. Transmission electron microscopy revealed the formation of powders of nano order size and the crystal size was found to vary from 30 to 85 nm. Dispersion in dielectric constant (ε) and dielectric loss (tan δ) in the low-frequency range have been observed. It is seen that nanocomposites exhibit strong magnetic properties and a large ME effect. On increasing Ni_0.75Co_0.25Fe₂O₄ contents in the nanocomposites, the saturation magnetization (M_S) and coercivity (H_C) increased after annealing at 700 °C. The large ME output in the nanocomposites exhibits strong dependence on magnetic bias and magnetic field frequency. The large value of ME output can be attributed to small grain size of ferrite phase of nanocomposite being prepared by citrate precursor process.