An optode membrane for determination of gold using a simple light-emitting diode-based device

Abstract  

A selective optode based on immobilization of 5-(p-dimethylaminobenzylidene)rhodanine on a triacetylcellulose membrane was developed for quantitative determination of Au(III). The determination procedure was performed using a simple light-emitting diode (LED)-based device as a new effort to overcome low reproducibility and repeatability problems which usually accompany optode-based determinations. The results obtained were compared with those of conventional spectrophotometric methods. The response characteristics of the sensor including dynamic range, reproducibility, response time, and lifetime are discussed in detail. This sensor was used for the determination of Au(III) in ore and electroplating liquid effluent samples with satisfactory results in comparison with flame atomic absorption spectroscopy as standard method. Under the optimum conditions, the calibration plot was linear in the concentration range of 0.3–6.0 μg cm⁻³. The relative standard deviations for five replicate determinations of 1.0 μg cm⁻³ Au(III) and the corresponding limits of detection were 1.76% and 0.12 μg cm⁻³, respectively.     

Rapid residue analysis of four triazolopyrimidine herbicides in soil, water, and wheat by ultra-performance liquid chromatography coupled to tandem mass spectrometry

A sensitive and effective method for simultaneous determination of triazolopyrimidine sulfonamide herbicide residues in soil, water, and wheat was developed using ultra-performance liquid chromatography coupled with tandem mass spectrometry. The four herbicides (pyroxsulam, flumetsulam, metosulam, and diclosulam) were cleaned up with an off-line C18 SPE cartridge and detected by tandem mass spectrometry using an electrospray ionization source in positive mode (ESI+). The determination of the target compounds was achieved in <2.0 min. The limits of detection were below 1 μg kg⁻¹, while the limits of quantification did not exceed 3 μg kg⁻¹ in different matrices. Quantitation was determined from calibration curves of standards containing 0.05–100 μg L⁻¹ with r ² > 0.997. Recovery studies were conducted at three spiked levels (0.2, 1, and 5 μg kg⁻¹ for water; 5, 10, and 100 μg kg⁻¹ for soil and wheat). The overall average recoveries for this method in water, soil, wheat plants, and seeds at three levels ranged from 75.4% to 106.0%, with relative standard deviations in the range of 2.1–12.5% (n = 5) for all analytes.     

Sensitive amperometric detection of omeprazole and pantoperazole at electrodeposited nickel oxide nanoparticles modified glassy carbon electrode

Glassy carbon electrode modified with electrodeposited nickel oxide nanoparticles (NiOxNPs) was used as electrocatalyst for oxidation of omeprazole and pentoperazole in alkaline solution. The modified electrode exhibited efficient electrocatalytic activity for the oxidation of omeprazole and pentoperazole with relatively high sensitivity, excellent stability, and long lifetime. Hydrodynamic amperometric method is used for determination of selected analytes. Under optimized condition, the linear concentration range, detection limit, and sensitivity of modified electrode toward omeprazole detection are 4.5–120 μM, 0.4 μM (at signal to noise 3), and 40.1 nA μM⁻¹ cm⁻², respectively. For pantoperazole, hydrodynamic amperometric determination yielded calibration curve with linear range of 2.5–180 μM, detection limit of 0.2 μM, and sensitivity of 39.2 nA μM⁻¹ cm⁻², respectively. The proposed method was successfully applied to pentoperazole and omeprazole determination in drug samples.     

Design and characteristics of tin (II) optode based on immobilization of dithizone on a triacetylcellulose membrane and its application in canned foods

Abstract  

The characterization of an optical sensor membrane is described for the determination of tin (II) based on the immobilization of dithizone on a triacetylcellulose membrane. The membrane responds to tin (II) ions by changing color reversibly from green to red in buffer solution at pH 6 and wavelength 611 nm. This optode has a linear range of 0.3–6.33 μg cm⁻³ (2.52–53.32 μmol dm⁻³) of Sn²⁺ ions with a limit of detection of 0.15 μg cm⁻³ (1.26 μmol dm⁻³). The response time of the optode was about 8–10 min depending on the concentration of Sn²⁺ ions. The selectivity of the optode to tin (II) ions at pH 6 was good. The sensor can be readily regenerated by exposure with EDTA solution. The color is fully reversible, and the optical sensor could be fully regenerated. Experimental results showed that the optode could be used as an effective tool in analyzing the tin content in canned foods.     

Simultaneous First Derivative Spectrophotometric Determination of Palladium and Nickel Using 2-(2-Thiazolylazo)-5-Dimethylaminobenzoic Acid as an Analytical Reagent

 A simple, rapid, selective, sensitive and economical method has been developed for the simultaneous determination of trace amounts of palladium and nickel in aqueous methanolic medium using 2-(2-thiazolylazo)-5-dimethylam inobenzoic acid as an analytical reagent by first derivative spectrophotometr y. Palladium is determined by measuring base to peak distance at λ=695.0 nm while nickel is estimated by zero crossing method in the mixture. The linearity is maintained between 0.12–1.75 μg mL⁻¹ for palladium and 0.07–1.60 μg mL⁻¹ for nickel in the pH range 2.8–7.2 and 3.4–8.8 respectively. Seven replicate determinations of 1.0 μ g mL⁻¹ of palladium and 0.8 μg mL⁻¹ of nickel in a mixture give a mean signal height of 0.391 for Pd and 0.541 for Ni with relative standard deviations of 0.9% and 1.2%, respectively. The sensitivity of the proposed method is 0.391 (dA/dλ)/(μg mL⁻¹) for palladium and 0.685 (dA/dλ)/(μg mL⁻¹) for nickel. Various parameters have been optimised for the simultaneous determination of palladium and nickel in various complex samples. Received March 30, 1999. Revision November 25, 1999.     

Comparison of the efficiency of different extraction methods for the simultaneous determination of mycotoxins and pesticides in milk samples by ultra high-performance liquid chromatography-tandem mass spectrometry

A rapid multi-analyte method has been developed for the simultaneous determination of pesticides and mycotoxins in milk by ultra high-performance liquid chromatography coupled to triple quadrupole mass spectrometry (UHPLC–QqQ–MS/MS). A variety of methodologies has been evaluated, including solid-phase extraction (SPE), “dilute-and-shoot” (liquid–liquid extraction-based procedures), and QuEChERS (quick, easy, cheap, effective, rugged, and safe)-based methods. The optimization and development process was carried out considering that the maximum residue level for aflatoxin M1 (AFM1) in milk in the European Union (EU) is set at 0.05 μg kg⁻¹, which is the lowest tolerance in the target compounds. The selected method consisted of an extraction by SPE using C18 as sorbent and methanol as elution solvent. The final determination was performed by UHPLC–QqQ–MS/MS. Matrix-matched standard calibration was used for quantification, obtaining recoveries in the range 60–120% with relative standard deviations <25%, at three spiking levels: 0.5, 10, and 50 μg kg⁻¹ (ten times lower for AFM1). Limits of quantification ranged from 0.20 to 0.67 μg kg⁻¹, which were always below or equal to the established tolerance levels by the EU. Finally, the selected method was applied to different types of milk.     

Ultrasound-enhanced surfactant-assisted dispersive liquid–liquid microextraction and high-performance liquid chromatography for determination of ketoconazole and econazole nitrate in human blood

A simple and efficient method, based on ultrasound-enhanced surfactant-assisted dispersive liquid–liquid microextraction (UESA-DLLME) followed by high-performance liquid chromatography (HPLC) has been developed for extraction and determination of ketoconazole and econazole nitrate in human blood samples. In this method, a common cationic surfactant, cetyltrimethylammonium bromide (CTAB), was used as dispersant. Chloroform (40 μL) as extraction solvent was added rapidly to 5 mL blood containing 0.068 mg mL⁻¹ CTAB. The mixture was then sonicated for 2 min to disperse the organic chloroform phase. After the extraction procedure, the mixture was centrifuged to sediment the organic chloroform phase, which was collected for HPLC analysis. Several conditions, including type and volume of extraction solvent, type and concentration of the surfactant, ultrasound time, extraction temperature, pH, and ionic strength were studied and optimized. Under the optimum conditions, linear calibration curves were obtained in the ranges 4–5000 μg L⁻¹ for ketoconazole and 8–5000 μg L⁻¹ for econazole nitrate, with linear correlation coefficients for both >0.99. The limits of detection (LODs, S/N = 3) and enrichment factors (EFs) were 1.1 and 2.3 μg L⁻¹, and 129 and 140 for ketoconazole and econazole nitrate, respectively. Reproducibility and recovery were good. The method was successfully applied to the determination of ketoconazole and econazole nitrate in human blood samples.     

Analysis of captan, folpet, and captafol in apples by dispersive liquid–liquid microextraction combined with gas chromatography

A novel method was developed for the determination of captan, folpet, and captafol in apples by dispersive liquid–liquid microextraction (DLLME) coupled with gas chromatography–electron capture detection (GC–ECD). Some experimental parameters that influence the extraction efficiency, such as the type and volume of the disperser solvents and extraction solvents, extraction time, and addition of salt, were studied and optimized to obtain the best extraction results. Under the optimum conditions, high enrichment factors for the compounds were achieved ranging from 824 to 912. The recoveries of fungicides in apples at spiking levels of 20.0 μg kg⁻¹ and 70.0 μg kg⁻¹ were 93.0–109.5% and 95.4–107.7%, respectively. The relative standard deviations (RSDs) for the apple samples at 30.0 μg kg⁻¹ of each fungicide were in the range from 3.8 to 4.9%. The limits of detection were between 3.0 and 8.0 μg kg⁻¹. The linearity of the method ranged from 10 to 100 μg kg⁻¹ for the three fungicides, with correlation coefficients (r ²) varying from 0.9982 to 0.9997. The obtained results show that the DLLME combined with GC–ECD can satisfy the requirements for the determination of fungicides in apple samples. Figure Dispersive liquid–liquid microextraction (DLLME) coupled with gas chromatography–electron capture detection (GC–ECD) allows satisfactory determination of fungicides in apple samples     

Flavonol Derivatives for Determination of Cr(III) and W(VI)

 Simple, rapid, sensitive and selective methods for the determination of Cr(III) and W(VI) with flavonol derivatives in the presence of surface-active agents are proposed. In the pH ranges 3.4–4.2 and 1.9–2.5, the molar absorptivities of Cr(III)-morin-emulsifier S (EFA) and W(VI)-morin-polyvinylpyrrolidone (PVP) systems are 1.13×10⁵ and 2.13×10⁴ L mol⁻¹ cm⁻¹ at 435 and 415 nm, respectively. The Cr(III)-quercetin-PVP and W(VI)-quercetin-cetylpyridinium bromide (CPB) systems are formed in the pH ranges 4–4.6 and 2.2–2.8 with molar absorptivities 1.02×10⁵ and 9.02×10⁴ L. mol⁻¹ cm⁻¹ at 441 and 419 nm, respectively. The linear dynamic ranges for the determination of Cr(III) and W(VI) with morin in the presence of EFA and PVP are 0.03–0.46 and 0.71–8.1 μg mL⁻¹, respectively. The corresponding ranges with quercetin are 0.04–0.54 and 0.14–2.1 μg mL⁻¹ of Cr(III) and W(VI), respectively. The r.s.d (n = 10) for the determination of 0.25 and 3.7 μg mL⁻¹ of Cr(III) and W(VI) with morin and their detection limits are 0.88 and 0.99% and 0.016 and 0.63 μg mL⁻¹, respectively. Using quercetin, the r.s.d (n = 10) for 0.22 and 1.2 μg mL⁻¹ of Cr(III) and W(VI) and their detection limits are 0.92 and 0.91% and 0.015 and 0.08 μg mL⁻¹, respectively. The critical evaluation of the proposed methods is performed by statistical analysis of the experimental data. The proposed methods are applied to determine Cr in steel, non-ferrous alloys, wastewater and mud filtrate and to the determination of W in steel. Received March 8, 1999. Revision January 21, 2000.     

Determination of low-level ink photoinitiator residues in packaged milk by solid-phase extraction and LC-ESI/MS/MS using triple-quadrupole mass analyzer

A confirmatory and quantitative method based on liquid chromatography–electrospray ionization tandem mass spectrometry (LC-ESI/MS/MS) has been developed for simultaneous determination of seven photoinitiator residues: benzophenone, (1-hydroxycyclohexyl)phenylketone (Irgacure 184), isopropylthioxanthone (ITX), 2-ethylhexyl-(4-dimethylamino)benzoate (EHA or EHDAB), 2-methyl-1-[4-(methylthio)phenyl]-2-(4-morpholinyl)-1-propanone (Irgacure 907), (2,4,6-trimethylbenzoyl)diphenylphosphine oxide (TPO) and 2-benzyl-2-(dimethylamino)-1-(4-morpholinophenyl)-1-butanone (Irgacure 369) in packaged milk and related packaging materials. Residues of photoinitiators were extracted from milk using acetonitrile, and further enriched and purified on HLB solid-phase extraction cartridges prior to being analyzed by LC-ESI/MS/MS with selected reaction monitoring mode, while photoinitiators in packaging materials were extracted using the same solvent. Satisfactory recovery (from 80 to 111%), intra- and inter-day precision (below 12%), and low limits of quantification (from 0.1 to 5.0 μg kg⁻¹) were evaluated from spiked samples at three concentration levels (5.0, 10.0 and 25.0 μg kg⁻¹ for Irgacure 184 and 2.5, 5.0 and 25.0 μg kg⁻¹ for others). These excellent validation data suggested the possibility of using the LC-ESI/MS/MS method for simultaneous determination of low-level photoinitiator residues migrating from printed food-packaging materials into milk. The method has been successfully applied to the analysis of real samples of different fat contents ranging from 8 to 30 g L⁻¹. The photoinitiator residues were revealed to be higher in milk with higher fat content and the most important contaminations were benzophenone and ITX in concentration ranges of 2.84–18.35 and 0.83–8.87 μg kg⁻¹, respectively.     

Separation and quantitation of oxprenolol in urine and pharmaceutical formulations by HPLC using a Chiralpak IC and UV detection

Abstract  

A stereoselective HPLC method has been developed for the simultaneous determination of oxprenolol enantiomers in urine and pharmaceutical products. Enantiomeric resolution of oxprenolol was achieved on cellulose tris(3,5-dichlorophenylcarbamate) immobilized onto a 5 μm spherical porous silica chiral stationary phase (CSP) known as Chiralpak IC with UV detection at 273 nm. The mobile phase consisted of n-hexane:isopropanol:triethylamine 70:30:0.1 (v/v/v) at a flow rate of 1.0 cm³/min. The method was validated for its linearity, accuracy, precision, and robustness. The calibration curves were linear over the range of 0.5–75 μg/cm³, with a detection limit of 0.1 μg/cm³ for each enantiomer. An average recovery of 99.0% and a mean relative standard deviation of 2.6% at 40.0 μg/cm³ for S-(−)- and R-(+)-enantiomers were obtained. The overall recoveries of oxprenolol enantiomers from pharmaceutical formulations were in the range 97.5–99.0%, with RSDs ranging from 0.6 to 0.8%. The mean extraction efficiency of oxprenolol from urine was in the range of 86.0–93.0% at 0.5–5 μg/cm³ for each enantiomer. The assay method proved to be suitable as a chiral quality control for oxprenolol formulations using HPLC and for therapeutic drug monitoring.     

Comparative study of inorganic elements determination in whole blood from Crioula breed horse by EDXRF and NAA analytical techniques

The World Health Organization states that envenomation is responsible for a high number of deaths per year, especially in equatorial areas. The only effective specific treatment is the use of hyperimmune serum (antivenom). In Brazil, Crioula breed horses are used for antivenom production, with great importance in the maintenance of public health programs. A strict biochemical and metabolic control is required to attain specificity in antiserum. Inorganic elements represent only a small fraction of whole blood. Nonetheless, they play important roles in mammalian metabolism, being responsible for controlling enzymatic reactions, respiratory and cardiac functions and ageing. In this work, whole blood samples from Crioula breed horses were analyzed by EDXRF technique. The reference interval values were determined for the elements Na (1955–2013 μg g⁻¹), Mg (51–75 μg g⁻¹), P (523–555 μg g⁻¹), S (1628–1730 μg g⁻¹), Cl (2388–2574 μg g⁻¹), K (1649–1852 μg g⁻¹), Ca (202–213 μg g⁻¹), Cu (4.1–4.5 μg g⁻¹) and Zn (2.4–2.8 μg g⁻¹) and a comparative study with NAA results was outlined. The samples were obtained from Instituto Butantan. Both techniques showed to be appropriate for whole blood sample analyses and offer a new perspective in Veterinary Medicine.     

Kinetic spectrophotometric determination of amodiaquine and chloroquine

Abstract  

Two simple, sensitive, and selective spectrophotometric methods were developed for determining amodiaquine (AQ) and chloroquine (CQ) based on their oxidation with potassium iodate and potassium bromate, respectively. The initial rates of oxidation of AQ and CQ were monitored at 342 and 343 nm, the wavelengths of maximum absorptions of the two drugs. The various experimental parameters affecting oxidation reactions were thoroughly studied and optimized. Beer’s law was obeyed for 0.2–4.0 and 0.5–5.0 μg cm⁻³, with correlation coefficients of 0.9999 and 0.9998 (n = 6) and a detection limit (based on the 3S _b -criterion) of 0.04 and 0.06 μg cm⁻³ for AQ and CQ. The proposed methods were conveniently applied to determining AQ and CQ in pure and dosage forms.     

Simultaneous extraction of polycyclic aromatic hydrocarbons and polychlorinated biphenyls in agricultural soils by pressurized liquid extraction and determination by gas chromatography coupled to tandem mass spectrometry

A simple and rapid method based on pressurized liquid extraction has been validated for the simultaneous extraction of polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs) from agricultural soil samples. Effective extraction was carried out in less than 17 min for all the studied compounds, and good recoveries were obtained for PAHs and PCBs, ranging from 70% to 112%, when blank samples were spiked at 2.5 μg kg⁻¹, except for naphthalene with recoveries close to 40%. The separation and determination were performed by gas chromatography coupled to tandem mass spectrometry using a triple quadrupole mass analyzer. The target compounds were detected by electron impact with selected reaction monitoring, and mass spectrometric conditions were optimized in order to increase selectivity and sensitivity. The developed method was validated, and matrix-matched calibration was used for quantification purposes. Repeatability and interday precision ranged from 0.9% to 16.8% and from 1.6% to 22.3%, respectively. Limits of quantification ranged from 0.07 to 2.50 μg kg⁻¹. The proposed method was applied to the analysis of agricultural soil samples collected from Almeria (Spain), and PAHs and PCBs were detected in some samples at concentrations ranging from 0.1 to 210 μg kg⁻¹.     

Kinetic spectrophotometric determination of amodiaquine and chloroquine

Abstract  Two simple, sensitive, and selective spectrophotometric methods were developed for determining amodiaquine (AQ) and chloroquine (CQ) based on their oxidation with potassium iodate and potassium bromate, respectively. The initial rates of oxidation of AQ and CQ were monitored at 342 and 343 nm, the wavelengths of maximum absorptions of the two drugs. The various experimental parameters affecting oxidation reactions were thoroughly studied and optimized. Beer’s law was obeyed for 0.2–4.0 and 0.5–5.0 μg cm⁻³, with correlation coefficients of 0.9999 and 0.9998 (n = 6) and a detection limit (based on the 3S _b -criterion) of 0.04 and 0.06 μg cm⁻³ for AQ and CQ. The proposed methods were conveniently applied to determining AQ and CQ in pure and dosage forms. Graphical abstract        

Multisyringe flow injection spectrophotometric determination of uranium in water samples

A multisyringe flow injection analysis method for the determination of uranium in water samples was developed. The methodology was based on the complexation reaction of uranium with arsenazo (III) at pH 2.0. Uranium concentrations were spectrophotometrically detected at 649 nm using a light emitting diode. Under the optimized conditions, a linear dynamic range from 0.1 to 4.0 μg mL⁻¹, a 3σ detection limit of 0.04 μg mL⁻¹, and a 10σ quantification limit of 0.10 μg mL⁻¹ were obtained. The reproducibility (%) at 0.5, 2.5, and 4.0 μg mL⁻¹ was 2.5, 0.9, and 0.6%, respectively (n = 10). The interference effect of some ions was tested. The proposed method was successfully applied to the determination of uranium in water samples.     

Preconcentration of uranium(VI) and thorium(IV) from aqueous solutions using low-cost abundantly available sorbent

Olive cake as low-cost abundantly available sorbent has been characterized by N₂ at 77 K adsorption, porosity analysis, elemental analysis and IR spectra and has been used for preconcentrating of uranium(VI) and thorium(IV) ions prior to their determination spectrophotometrically. The optimum pH values for quantitative sorption of U(VI) and Th(IV) are 4–7 and 3–7, respectively. The enrichment factor for the preconcentration of U(VI) and Th(IV) were found to be 125 and 75 in the given order. The sorption capacity of olive cake is in the range of 2,260–15,000 μg g⁻¹ for Th(IV) and in the range of 1,090–17,000 μg g⁻¹ for U(VI) at pH 3–7. The sorbent exhibits good reusability and the uptake and stripping of the studied ions were fairly rapid. The elution of U(VI) and Th(IV) was performed with 0.3–1 M HCl/1–2 M HNO₃ and 0.3–0.8 M HCl/1 M HNO₃, respectively. The precision of the method was 1.8 RSD% for U(VI) and 2.5 RSD% for Th(IV) in a concentration of 1.00 μg mL⁻¹ for 10 replicate analysis. The influence of some electrolytes and cations as interferents was discussed. Separation of U(VI) and Th(IV) from other metal ions in synthetic solution was achieved.     

Tetracycline residues in royal jelly and honey by liquid chromatography tandem mass spectrometry: validation study according to Commission Decision 2002/657/EC

A specific, sensitive and robust liquid chromatography tandem mass spectrometry method for determining oxytetracycline, tetracycline, chlortetracycline and doxycycline in royal jelly and honey samples is presented. Extraction of drug residues was performed by ammonium acetate buffer as extractant followed by a clean-up with metal chelate affinity chromatography and solid-phase extraction. Tetracycline analysis was performed using liquid chromatography–electrospray ionisation–tandem mass spectrometry. The presented method is the first validated for royal jelly and in accordance with the requirements set by Commission Decision 2002/657/EC. Recoveries of the methods, calculated spiking the samples at 5.0, 10.0, 20.0 and 30.0 μg kg⁻¹, were 79% to 90% for honey and 77% to 90% for royal jelly. The intra-day precision (RSD) ranged between 8.1% and 15.0% for honey and from 9.1% to 16.3% for royal jelly, while inter-day precision values were from 10.2% to 17.6% and from 10.6% to 18.4% respectively for honey and royal jelly. Linearity for the four analytes was calculated from 5.0 to 50.0 μg kg⁻¹. The decision limits (CCα) ranged from 6.2 to 6.4 μg kg⁻¹ and from 6.1 to 6.5 μg kg⁻¹ for honey and royal jelly, respectively. Detection capabilities values (CCβ) ranged between 7.2 and 7.7 μg kg⁻¹ and from 7.3 to 7.9 μg kg⁻¹ respectively for honey and royal jelly. The developed method is currently in use for confirmation of the official control analysis of honey and royal jelly samples.     

Studies on uranium recovery from inlet stream of Effluent Treatment Plant by novel “In-House” sorbent

A fast and simple multisyringe flow injection analysis (MSFIA) method for routine determination of thorium in water samples was developed. The methodology was based on the complexation reaction of thorium with arsenazo (III) at pH 2.0. Thorium concentrations were spectrophotometrically detected at 665 nm. Under optimal conditions, Beer’s law was obeyed over the range from 0.2 to 4.5 μg mL⁻¹ thorium, a 3σ detection limit of 0.05 μg mL⁻¹, and a 10σ quantification limit of 0.2 μg mL⁻¹ were obtained. The relative standard deviations (RSD, %) at 0.5, 2.5 and 4.5 μg mL⁻¹ was 2.8, 1.5 and 0.8%, respectively (n = 10). It was found that most of the common metal ions and anions did not interfere with the thorium determination. The proposed method was successfully applied to its analysis in various water samples.     

Determination of antibacterials in animal feed by pressurized liquid extraction followed by online purification and liquid chromatography-electrospray tandem mass spectrometry

A fully automated method has been developed for analysis of eighteen antibacterial compounds, including penicillins, cephalosporins and sulfonamides, in animal feed with limits of quantification in the range 0.25–5.79 μg kg⁻¹. The method is based on pressurized liquid extraction of 3 g homogenized feed with water and online clean-up of 500 μL of the extract with C₁₈HD cartridges. The purified sample was directly analysed by liquid chromatography–electrospray tandem mass spectrometry (SPE–LC–ESI-MS–MS). Chromatographic separation was achieved within 10 min by use of a C₁₂ Phenomenex Hydro-RP reversed-phase analytical column and a mobile phase gradient (water + 0.1% formic acid–methanol + 0.1% formic acid). The method was validated, revealing capability for detection of concentrations as low as 0.09 μg kg⁻¹, decision limits (CCα) and detection capabilities (CCβ) in the range 10–174 μg kg⁻¹ and 22–182 μg kg⁻¹, respectively, and inter-day precision ranging from 0.7 to 8.3%. Recovery, with internal standard correction, was in the range 93–134% for all analytes. The method was then applied to analysis of fifteen feed samples, nine of which contained at least one antimicrobial at concentrations between 0.006 and 1.526 mg kg⁻¹. The performance data and results from the method were compared with those from a previous method developed by our group, using offline SPE, by analyzing the same set of samples by both methods. The online SPE approach resulted in slightly improved sensitivity, with LODs of 0.09–2.12 μg kg⁻¹ compared with 0.12–3.94 μg kg⁻¹ by the offline approach. In general, better recovery was achieved by use of online purification (for 72% of the analytes) and the correlation between the two methods was good. The main advantages of the new online method are rapid and automated sample pre-treatment, and reduction of sample manipulation, enabling high-throughput analysis and highly accurate results. Because of all these characteristics, the proposed method is applicable and could be deemed necessary within the field of food control and safety.