Poly(L-lactide) (PLLA)/multiwalled carbon nanotube (MWCNT) composite: characterization and biocompatibility evaluation

Much effort has been directed at the fabrication of carbon nanotubes (CNTs)/polymer composites and the characterization of their physical properties. Among them, composites comprising CNTs and the biocompatible polymers are of special interest due to their potential for specific biomedical applications. we report the preparation of the MWCNT/poly(L-lactide) composite and the corresponding spectroscopic (Raman) and the microscopic (SEM, TEM) characterization. The electronic transport, thermal properties, and biocompatibility of this composite have also been investigated. The Raman spectroscopic analysis suggests the interaction between PLLA and MWCNT occurs mainly through the hydrophobic C-CH3 functional groups. The DC conductivity of the composite increases as the MWCNT loading is increased. Such behavior can be described by a percolation mechanism in which a percolation threshold at about 14 wt % MWCNT loading is observed with the maximum end conductivity of 0.1 S x cm(-1). The DSC study of the PLLA/MWCNT composite reveals that the MWCNTs in the composite have the effect of inducing crystallization and plasticizing the polymer matrix. The results from the cell culture test suggest that the presence of MWCNT in the composite inhibits the growth of the fibroblast cells.     

Poly(epsilon-caprolactone)/clay nanocomposites via “click” chemistry

Poly(epsilon-caprolactone)/clay nanocomposites were prepared by copper(I) catalyzed azide/alkyne cycloaddition (CuAAC) “click” reaction. In this method, ring-opening polymerization of epsilon-caprolactone using propargyl alcohol as the initiator has been performed to produce alkyne-functionalized PCL and the obtained polymers were subsequently attached to azide-modified clay layers by a CuAAC “click” reaction. The exfoliated polymer/clay nanocomposites were characterized by X-ray diffraction spectroscopy, thermogravimetric analysis and transmission electron microscopy.     

Synthesis and characterization of carbon nanotube/polypyrrole core–shell nanocomposites via in situ inverse microemulsion

We demonstrate here a feasible approach to the preparation of multiwalled carbon nanotube (MWNT)/polypyrrole (PPy) core–shell nanowires by in situ inverse microemulsion. Transmission electron microscopy and scanning electron microscopy showed that the carbon nanotubes were uniformly coated with a PPy layer with a thickness of several to several tens of nanometers, depending on the MWNT content. Fourier transform infrared spectra suggested that there was strong interaction between the π‐bonded surface of the carbon nanotubes and the conjugated structure of the PPy shell layer. The thermal stability and electrical conductivity of the MWNT/PPy composites were examined with thermogravimetric analysis and a conventional four‐probe method. In comparison with pure PPy, the decomposition temperature of the MWNT/PPy (1 wt % MWNT) composites increased from 305 to 335 °C, and the electrical conductivity of the MWNT/PPy (1 wt % MWNT) composites increased by 1 order of magnitude. The current–voltage curves of the MWNT/PPy nanocomposites followed Ohm's law, reflecting the metallic character of the MWNT/PPy nanocomposites. The cyclic voltammetry measurements revealed that PPy/MWNT composites showed an enhancement in the specific charge capacity with respect to that of pure PPy. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6105–6115, 2005     

Poly(styrene-co-butyl acrylate)/mesoporous diatomaceous earth mineral nanocomposites by in situ AGET ATRP

Journal of Thermal Analysis and Calorimetry - Mesoporous diatomite platelets were used for in situ copolymerization of styrene and butyl acrylate by activators generated by electron transfer for...     

Preparation and characterization of poly(ethyl acrylate)/bentonite nanocomposites by in situ emulsion polymerization

Transparent poly(ethyl acrylate) (PEA)/bentonite nanocomposites containing intercalated–exfoliated combinatory structures of clay were synthesized by in situ emulsion polymerizations in aqueous dispersions containing bentonite. The samples for characterization were prepared through direct‐forming films of the resulting emulsions without coagulation and separation. An examination with X‐ray diffraction and transmission electron microscopy showed that intercalated and exfoliated structures of clay coexisted in the PEA/bentonite nanocomposites. The measurements of mechanical properties showed that PEA properties were greatly improved, with the tensile strength and modulus increasing from 0.65 and 0.24 to 11.16 and 88.41 MPa, respectively. Dynamic mechanical analysis revealed a very marked improvement of the storage modulus above the glass‐transition temperature. In addition, because of the uniform dispersion of silicate layers in the PEA matrix, the barrier properties of the materials were dramatically improved. The permeability coefficient of water vapor decreased from 30.8 × 10^?6 to 8.3 × 10^?6 g cm/cm² s cmHg. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1706–1711, 2002     

Poly(cyclohexene oxide)/clay nanocomposites by photoinitiated cationic polymerization via activated monomer mechanism

Poly(cyclohexene oxide) (PCHO)/clay nanocomposites were prepared by in situ photoinitiated activated monomer cationic polymerization. The polymerization of cyclohexene oxide through the interlayer galleries of the clay can provide distribution of the clay layers in the polymer matrix homogenously and results in the formation of PCHO/clay nanocomposites. The exfoliated structures were characterized by X‐ray diffraction spectroscopy, thermogravimetric analysis, transmission electron microscopy, and atomic force microscopy. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5328–5335, 2009     

Enhanced performance of biodegradable poly(butylene succinate)/graphene oxide nanocomposites via in situ polymerization

Poly(butylene succinate) (PBS)/graphene oxide (GO) nanocomposites were facilely prepared via in situ polymerization. The properties of the nanocomposites were studied using FTIR, XRD, and (1)H NMR, and the state of dispersion of GO in the PBS matrix was examined by SEM. The crystallization and melting behavior of the PBS matrix in the presence of dispersed GO nanosheets have been studied by DSC and polarized optical microscopy. Through the mechnical testing machine and DMA, PBS/GO nanocomposites with 3% GO have shown a 43% increase in tensile strength and a 45% improvement in storage modulus. This high performance of the nanocomposites is mainly attributed to the high strength of graphene oxide combined with the strong interfacial interactions in the uniformly dispersed PBS/GO nanocomposites.     

Poly(vinyl alcohol)/GO-MMT nanocomposites: Preparation,structure and properties

A facile, efficient and environment friendly method is established to prepare poly(vinyl alcohol)(PVA) based graphene oxide-montmorillonite(GO-MMT) nanocomposites in aqueous media. GO-MMT nanohybrid is obtained by the combination of GO and MMT in water without any reducing or stabilizing agents. The formation of GO-MMT nanohybrid is due to the hydrogen bonding and crosslinking effects. The sodium ions within MMT sheets act as crosslinkers between GO sheets and MMT platelets. The resultant nanocomposites are characterized by means of X-ray diffraction(XRD), scanning electron microscopy(SEM), differential scanning calorimetry(DSC), thermogravimetric analysis(TGA) and mechanical testing. Compared to that of pure PVA, PVA nanocomposites show enhanced thermal stabilities and mechanical properties, which results from strong interfacial adhesion of the nanoadditives in PVA matrix. The further increase in the tensile strength and modulus results from strong interaction between PVA chains and layered GO-MMT as well as good mechanical properties of GO-MMT hybrid, compared to PVA/GO and PVA/MMT nanocompsoites.     

Poly(1‐butene)/clay nanocomposites: Preparation and properties

The preparation and properties of poly(1‐butene) (PB)/clay nanocomposites are described for the first time. Nanocomposites were prepared with the melt‐intercalation technique, using organically modified clay. The X‐ray diffraction patterns portrayed well‐defined diffraction peaks at higher d‐spacing than pristine clay, confirming the intercalation of polymer in silicate layers. Because PB exhibits time‐dependent polymorphism, the effect of clay on the phase transformation of PB was examined with thermal analysis. The phase transformation from a metastable tetragonal form to a stable hexagonal form was enhanced because of incorporation of layered silicates in the polymer matrix. The nanocomposites exhibited about a 40–140% increase in storage modulus depending on the clay content and significantly lower coefficient of thermal expansion. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1014–1021, 2003     

Poly(vinyl chloride)/clay nanocomposites: X-ray diffraction, thermal and rheological behaviour

The paper concentrates on poly(vinyl chloride) - PVC - from the point of view of structural characterisation of PVC/clay nanocomposites through X-ray diffraction, thermogravimetric analysis and dynamic rheometric analysis. PVC plasticizer was mixed with clay, natural and organophilic, and the suspension was then compounded with other components. Two factors were followed: effect of shearing alone, and in combination with temperature. The type of filler and the method of composite preparation affect the mechanical and thermal properties of the composite, through delamination and exfoliation levels. The results showed that the thermal degradation is shifted towards higher temperatures for organophilic clays, compared to chemically untreated natural clay.     

Poly(3-hexylthiophene)/gold nanoparticle nanocomposites: relationship between morphology and electrical conductivity

The morphology and electrical properties of gold nanoparticles (AuNP) layer vacuum-deposited onto spin-cast thin films of poly(3-hexylthiophene), P3HT, were studied. The electrical conductivity was measured during temperature cycling and related to the morphology of the same composite structures, which was monitored by transmission electron microscopy (TEM) and extra-high resolution scanning electron microscopy (XHR SEM). Comparison to the analogous polystyrene/AuNP layers was made to distinguish the role of the polymer support on the morphology and electrical properties of the nanoparticles assembly. Gold deposited in a very thin layer formed a nanoparticles-like island structure with the morphology depending on the effective thickness of the deposited layer and on its subsequent thermal treatment. A stabilizing effect of the thiophene–gold interaction on the nanoparticles morphology was observed.     

Poly(lactic acid)/organoclay nanocomposites: Thermal,rheological properties and foam processing

In this study, polymer nanocomposites based on poly(lactic acid) (PLA) and organically modified layered silicates (organoclay) were prepared by melt mixing in an internal mixer. The exfoliation of organoclay could be attributed to the interaction between the organoclay and PLA molecules and shearing force during mixing. The exfoliated organoclay layers acted as nucleating agents at low content and as the organoclay content increased they became physical hindrance to the chain mobility of PLA. The thermal dynamic mechanical moduli of nanocomposites were also improved by the exfoliation of organoclay; however, the improvement was reduced at high organoclay content. The dynamic rheological studies show that the nanocomposites have higher viscosity and more pronounced elastic properties than pure PLA. Both storage and loss moduli increased with silicate loading at all frequencies and showed nonterminal behavior at low frequencies. The nanocomposites and PLA were then foamed by using the mixture of CO₂ and N₂ as blowing agent in a batch foaming process. Compared with PLA foam, the nanocomposite foams exhibited reduced cell size and increased cell density at very low organoclay content. With the increase of organoclay content, the cell size was decreased and both cell density and foam density were increased. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 689–698, 2005     

Biodegradable poly(lactic acid)/chitosan-modified montmorillonite nanocomposites: Preparation and characterization

In this study, the biodegradable poly(lactic acid) (PLA)/montmorillonite (MMT) nanocomposites were successfully prepared by the solution mixing process of PLA polymer with organically-modified montmorillonite (m-MMT), which was first treated by n-hexadecyl trimethyl-ammonium bromide (CTAB) cations and then modified by biocompatible/biodegradable chitosan to improve the chemical similarity between the PLA and m-MMT. Both X-ray diffraction data and transmission electron microscopy images of PLA/m-MMT nanocomposites indicate that most of the swellable silicate layers were disorderedly intercalated into the PLA matrix. Mechanical properties and thermal stability of the PLA/m-MMT nanocomposites performed by dynamic mechanical analysis and thermogravimetric analysis have significant improvements in the storage modulus and 50% loss in temperature when compared to that of neat PLA matrix. The degradation rates of PLA/m-MMT nanocomposites are also discussed in this study.     

Poly(methyl methacrylate)/multiwalled carbon nanotube microspheres fabricated via in‐situ dispersion polymerization

Poly(methyl methacrylate)/multiwalled carbon nanotube (PMMA/MWCNT) microspheres were successfully prepared by in situ dispersion polymerization in an alcohol phase in which the acid‐treated MWCNTs were dispersed before polymerization. The PMMA and PMMA/MWCNT microspheres were monodisperse. The diameters of the microspheres decreased from about 11.6–6.0 μm as the MWCNT content was increased from 0 to 0.03 wt %. The morphology of the PMMA/MWCNT microspheres was investigated by scanning electron microscopy, atomic force microscopy, and transmission electron microscopy, and the experimental results showed that the MWCNTs were present both in the interior and on the surface of the microspheres. The synthesized PMMA/MWCNT microspheres were also characterized by electrical resistance measurements to analyze their electrical conductivity. They showed electrorheological (ER) fluid characteristics when they were dispersed in silicone oil. Their ER properties were confirmed by using optical microscopy to examine a suspension of the PMMA/MWCNT microspheres dispersed in insulating silicone oil to which an electric field of 2.5 kV/cm was applied. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 182–189, 2008     

Preparation and characterization of polymer/silica nanocomposites via double in situ miniemulsion polymerization

Polymer/SiO₂ nanocomposite microspheres were prepared by double in situ miniemulsion polymerization in the presence of methyl methacrylate, butyl acrylate, γ‐methacryloxy(propyl) trimethoxysilane, and tetraethoxysilane (TEOS). By taking full advantage of phase separation between the growing polymer particles and TEOS, inorganic/polymer microspheres were fabricated successfully in a one‐step process with the formation of SiO₂ particles and the polymerization of organic monomers taking place simultaneously. The morphology of nanocomposite microspheres and the microstructure, mechanical properties, thermal properties, and optical properties of the nanocomposite films were characterized and discussed. The results showed that hybrid microspheres had a raspberry‐like structure with silica nanoparticles on the shells of polymer. The silica particles of about 20 nm were highly dispersed within the nanocomposite films without aggregations. The transmittance of nanocomposite film was comparable to that of the copolymer film at around 70–80% from 400 to 800 nm. The mechanical properties and the fire‐retardant behavior of the polymer matrix were improved by the incorporation of silica nanoparticles. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3128–3134, 2010     

Poly(dimethylsiloxane)/palygorskite composites: preparation,characterization, and properties

Poly(dimethylsiloxane) (PDMS) composites were prepared by simple blending process using palygorskite (PG) or modified palygorskite (MP). This study has been designed to determine the influences of PG or MP on the thermal stability and the mechanical properties of PDMS composites. The thermal stability of PG and MP were also studied by thermogravimetric analysis (TGA). The results showed that MP had the similar thermal stability to PG, and PG or MP not only increased the thermal stability but also improved the mechanical properties of PDMS composites. Meanwhile, compared with PG/PDMS composites, MP/PDMS composites had better thermal stability and mechanical properties owing to the better dispersion of MP into the matrix, the stronger chemical interfacial interaction between MP and the matrix. Copyright © 2010 John Wiley & Sons, Ltd.     

Poly(L‐lactide)/layered double hydroxides nanocomposites: Preparation and crystallization behavior

Novel nanocomposites from poly(L ‐lactide) (PLLA) and an organically modified layered double hydroxide (LDH) were prepared using the melt‐mixing technique. The structure and crystallization behavior of these nanocomposites were investigated by means of wide‐angle X‐ray diffraction (WAXD), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), and polarized optical microscopy (POM). WAXD results indicate that the layer distance of dodecyl sulfate‐modified LDH (LDH‐DS) is increased in the PLLA/LDH composites, compared with the organically modified LDH. TEM analysis suggests that the most LDH‐DS layers disperse homogenously in the PLLA matrix in the nanometer scale with the intercalated or exfoliated structures. It was found that the incorporation of LDH‐DS has little or no discernable effect on the crystalline structure as well as the melting behavior of PLLA. However, the crystallization rate of PLLA increases with the addition of LDH‐DS. With the incorporation of 2.5 wt % LDH‐DS, the PLLA crystallization can be finished during the cooling process at 5 °C/min. With the addition of 5 wt % LDH‐DS, the half‐times of isothermal melt‐crystallization of PLLA at 100 and 120 °C reduce to 44.4% and 57.0% of those of the neat PLLA, respectively. POM observation shows that the nucleation density increases and the spherulite size of PLLA reduces distinctly with the presence of LDH‐DS. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2222–2233, 2008     

New poly(ether-imide)/MWCNT nanocomposite

New polyimide (PI) nanocomposites containing two different amounts of MWCNT (PI/MWCNT) were prepared via in situ polymerization technique. Transmission electron microscopy showed that MWCNT was exfoliated in the polymer matrix, resulting in well-dispersed morphologies at 1 and 3 mass% MWCNT contents. The effects of multiwalled carbon nanotubes (MWCNT) on the thermal and flammability properties of new PI derived from 1,3-bis[4,4′-aminophenoxy]propane and biphenyl dianhydride were investigated by thermogravimetric analysis (TG) in nitrogen and air atmosphere, differential scanning calorimetry, and microscale combustion calorimeter (MCC). The PI/MWCNT nanocomposites were electrically conductive with maximum conductivity obtained at 3 mass% MWCNT, which is favorable for many potential applications. TG results showed that the addition of MWCNT resulted in a substantial increase of the thermal stability and char yields of the nanocomposites compared to those of the neat PI. Flame retardancy of the nanocomposites was significantly improved in the presence of MWCNT.     

Uncross‐linked polypropylene (PP)/ethylene‐propylene‐diene (EPDM)/multi walled carbon nanotube (MWCNT) and dynamically vulcanized PP/EPDM/MWCNT nanocomposites

In this study, relatively large amounts of polypropylene (PP), ethylene‐propylene‐diene (EPDM), and multi‐walled carbon nanotube (MWCNT) were melt‐mixed with and without DCP. Dynamically vulcanized PP/EPDM (TPV)/MWCNT nanocomposites were prepared by two methods: the MWCNTs were added either before or after the dynamic vulcanization of the blends. The effects of composition, rotor speed, and dynamic vulcanization on their surface resistivity were investigated. The surface resistivity of uncross‐linked PP/EPDM/MWCNT nanocomposites increases with increasing the content of EPDM. At PP/EPDM (70/30 wt%) nanocomposite with 1.5 phr MWCNT, slightly lower surface resistivity is obtained by increasing the rotor speed during mixing. However, for PP/EPDM (50/50 wt%) and PP/EPDM (30/70 wt%) nanocomposites, surface resistivity decreases with increasing the rotor speed from 30 to 60 rpm. But further increase in rotor speed (90 rpm) leads to an increase of surface resistivity. When the MWCNTs were added after the dynamic vulcanization of the blends, the surface resistivity of TPV70/MWCNTnanocomposite is lower than that of uncross‐linked PP/EPDM/MWCNT nanocomposite. However, when the MWCNTs were added before the dynamic vulcanization of the blends, the surface resistivity of TPV70/MWCNT nanocomposite is >10¹² Ω/square. Copyright © 2010 John Wiley & Sons, Ltd.     

Synthesis and characterization of Poly(N-isopropylacrylamide)/Poly(acrylic acid) semi-IPN nanocomposite microgels

A novel pH- and temperature-sensitive nanocomposite microgel based on linear Poly(acrylic acid) (PAAc) and Poly(N-isopropylacrylamide) (PNIPA) crosslinked by inorganic clay was synthesized by a two-step method. First, PNIPA microgel was prepared via surfactant-free emulsion polymerization by using inorganic clay as a crosslinker, and then AAc monomer was polymerized within the PNIPA microgel. The structure and morphology of the microgel were confirmed by FTIR, WXRD and TEM. The results indicated that the exfoliated clay platelets were dispersed homogeneously in the PNIPA microgels and acted as a multifunctional crosslinker, while the linear PAAc polymer chains incorporated in the PNIPA microgel network to form a semi-interpenetrating polymer network (semi-IPN) structure. The hydrodynamic diameters of the semi-IPN microgels ranged from 360 to 400 nm, which was much smaller than that of the conventional microgel prepared by using N,N′-methylenebis(acrylamide) (MBA) as a chemical crosslinker, the later was about 740 nm. The semi-IPN microgels exhibited good pH- and temperature-sensitivity, which could respond independently to both pH and temperature changes.