利用软模板和紫外光固化技术制备超疏水表面

研究了一种制备超疏水表面的新方法.该方法以复制了荷叶表面结构的聚二甲基硅氧烷(PDMS)弹性体为软模板.利用可紫外光交联预聚物在模板压印条件下固化成型,得到了具有微乳突结构的仿荷叶表面.制备的仿荷叶表面表现出了超疏水性能.通过对紫外光固化体系中的单体含量、交联剂含量、引发剂含量、以及紫外曝光时间等因素的研究,得到了使仿荷叶表面的疏水性优化的条件.     

基于热模塑法制备HDPE仿生超疏水表面

研究了热模塑法在制备超疏水高密度聚乙烯(HDPE)膜中的应用。以高岭土增强的聚二甲基硅氧烷(PDMS)为软模板,采用热模塑技术,将荷叶表面的微结构信息复制到HDPE膜表面。接触角测量结果显示,10%掺杂量的PDMS软模板复制得到的HDPE膜表面,与水的接触角高达156°,呈现超疏水性。扫描电镜照片显示,PDMS软模板具有与荷叶表面互补的"负型结构",而HDPE膜表面则具有与荷叶类似的微米—纳米复合粗糙结构。此法无需溶剂,可推广制备其它热塑性高聚物的超疏水表面。     

可粘贴超疏水薄膜的制备

通过聚二甲基硅氧烷(PDMS)与碳纤维织物复合, 采用模板法在PDMS聚合物表面构筑微阵列结构, 制备了一种具有可重复粘贴性的超疏水薄膜. 研究结果表明, 该薄膜微结构表面的接触角为154°, 滚动角为14°, 具有低黏附的超疏水特性. 而PDMS与碳纤维织物的紧密结合, 赋予了超疏水薄膜较高的黏接力和力学性能, 断裂强度达到116.96 MPa. 所制备的超疏水薄膜可粘贴于多种材料表面, 同时经过30 d的长时间粘贴以及50次的循环粘贴后, 该薄膜依然保持着较高的黏附性能及超疏水特征, 表明超疏水薄膜具有良好的力学稳定性及耐久性, 满足长时间可重复使用的要求, 可应用于对破损超疏水涂层的快速、 大面积粘贴修复.     

Zn片经水热反应和氟硅烷修饰构建超疏水ZnO表面

以乙二胺为溶剂, Zn片在120、140 及160 ℃经水热反应生长出具有蛋糕形、荷叶乳突状、棒状和仙人球状等微结构的ZnO表面. 扫描电镜研究表明, 反应时间越长越有利于形成完整的微纳米结构, 反应温度较高生成的微纳米结构更规整. 140 ℃反应4 h和160 ℃反应5 h的ZnO表面经过氟硅烷修饰后表现出良好的超疏水性, 与水滴的接触角分别达到154.6°和157.3°, 滚动角分别为5°和3°. 该方法因其操作简便、成本低廉, 在锌表面制备特殊微结构和构建超疏水表面具有潜在的应用.     

拉伸微模塑制备低密度聚乙烯超疏水表面

以新鲜荷叶为原始模板制备聚二甲基硅氧烷(PDMS)软模板,并用该软模板在真空下热压得低密度聚乙烯(LDPE),冷却剥离得到LDPE超疏水薄膜.场发射扫描电镜(FE-SEM)显示其表面由细长乳突(长约30 μm)构成,接触角为154°±3.5°,水滴极易滚落,而常压下热压得到的薄膜表面乳突则短而粗(长约8～10μm),接触角仅137°±2.7°,短粗的乳突高度接近模板微坑的深度,证明细长乳突是在微模塑脱模时拉伸形成的.     

CaCO_3颗粒模板法制备聚合物超亲水/超疏水表面

以碳酸钙(CaCO3)颗粒层为模板,运用简单的热压和酸蚀刻相结合的方法制备聚合物超亲水/超疏水表面.首先在玻璃基底上均匀铺撒一层CaCO3颗粒,以此作为模板,通过热压线性低密度聚乙烯(LLDPE)使CaCO3颗粒均匀镶嵌在聚合物表面,获得了超亲水性质;进一步经酸蚀得到了具有微米和亚微米多孔结构的表面,其水滴静态接触角(WCA)可达(152.7±0.8)°,滚动角小于3°,具备超疏水性质.表面浸润性能和耐水压冲击性能研究表明该超疏水表面具有良好的稳定性和持久性.用同样工艺微模塑/酸蚀刻其它疏水性聚合物,得到类似结果.     

直接浸泡法构筑纯铜的超疏水表面

以棕榈酸-乙醇溶液为疏水剂,利用直接浸泡法在纯铜表面上构筑了超疏水薄膜。 纯铜表面超疏水薄膜的最佳制备条件为：0.03 mol/L棕榈酸-乙醇溶液,室温（20～22 ℃）,浸泡144 h。 通过扫描电子显微镜、接触角测量仪、红外光谱仪和高精密电子天平对超疏水表面进行了表征和分析。 实验结果表明,纯铜试样表面形成了100～200 μm大小的草状棕榈酸铜微簇,接触角达到了150°,其具有较好的抗结垢性能。     

硅烷表面修饰引发的ZnO微米棒膜的超疏水性

采用简单的低温水热法制备出ZnO微米棒薄膜,其经辛基三甲氧基硅烷和十二氟庚基丙基三甲氧基硅烷修饰后显示出超疏水性,静态接触角分别为(150±1.3)°和(155±1.5)°,滚动角依次为5°和3°。 ZnO微米棒的微结构和低表面能材料辛基三甲氧基硅烷、十二氟庚基丙基三甲氧基硅烷的表面修饰是其显示超疏水性的原因,用Cassie理论对膜的润湿性进行了分析。     

软模板印刷法制备超疏水性聚苯乙烯膜

首次利用软模板印刷的方法,以微米-亚微米-纳米复合结构的PDMS为软模板,在平滑聚苯乙烯表面上成功制备了同样具有微米-亚微米-纳米复合结构的超疏水表面,该表面与水的接触角高达161.2º。软模板印刷方法可以用在其它热塑性聚合物如聚丙烯、聚甲基丙烯酸甲酯和聚碳酸酯等材料上,是一种简单有效地制备超疏水性表面的方法。     

以多孔CaCO3微球为模板制备聚乙烯超疏水表面

以聚苯乙烯磺酸钠（PSS）掺杂的多孔碳酸钙（CaCO3）微球层为模板,通过热压低密度聚乙烯（LDPE）并结合酸蚀刻的方法制得了具有多层粘联微球结构、而非常见蜂窝状多孔结构的LDPE稳定超疏水表面（接触角152.8±2.5°,滚动角约6°）。元素分析表明,表面粘联微球为纯LDPE而非LDPE包覆的CaCO3。将多孔CaCO3微球稀疏地撒在LDPE表面并加热熔融,发现微球会自发沉降到熔体内部,酸蚀刻后形成了类似莲蓬的表面微结构,即坑内包含小球。结合CaCO3微球生成原理和多孔结构,认为粘联微球结构和莲蓬结构均是由于LDPE熔融大分子自发沉积到多孔CaCO3微球内部,“反模”形成了LDPE微球所致。本发现为多孔CaCO3微球的应用开辟了新方向。     

Robust superhydrophobic surface fabrication by fluorine-free method on filter paper for oil/water separation

Robust superhydrophobic surface exhibiting anti-fouling and self-cleaning ability were successfully fabricated by nano TiO2 modified by γ-aminopropyltriethoxysilane (KH550) and polydimethylsiloxane (PDMS) via wire rod coating. Due to the lower surface energy of PDMS and the hierarchical structure caused by the different aggregation sizes of TiO2 nanoparticles, the contact angle of the resulting superhydrophobic coating was 154.5° and the rolling angle was 3.5°. And the coated paper still had good non-wettability under water immersion. In addition, the coated paper was tolerant to mechanical damage and various temperature conditions. Even after 40 sandpaper wear cycles, the coating can still maintain good mechanical stability and superhydrophobicity. The superhydrophobic paper was used for oil-water separation, the separation efficiency was about 98% even after used 10 times. Furthermore, the prepared superhydrophobic paper exhibited excellent self-cleaning and anti-fouling properties, as well as demonstrated superb resistance to various water solutions owing to its high hydrophobicity. Moreover, the prepared superhydrophobic paper has application prospects in the industry of special wetting materials.     

Evaporative properties and pinning strength of laser-ablated, hydrophilic sites on lotus-leaf-like, nanostructured surfaces

Wetting, evaporative, and pinning strength properties of hydrophilic sites on superhydrophobic, nanostructured surfaces were examined. Understanding these properties is important for surface characterization and designing features in self-cleaning, lotus-leaf-like surfaces. Laser-ablated, hydrophilic spots between 250 mum and 2 mm in diameter were prepared on silicon nanowire (NW) superhydrophobic surfaces. For larger circumference pinning sites, initial contact angle measurements resemble the contact angle of the surface within the pinning site: 65-69 degrees . As the drop volume is increased, the contact angles approach the contact angle of the NW surface without pinning sites: 171-176 degrees . The behavior of water droplets on the pinning sites is governed by how much of the water droplet is being influenced by the superhydrophobic NW surfaces versus the hydrophilic areas. During the evaporation of sinapic acid solution, drops are pinned by the spots except for the smaller circumference sites. Pinning strengths of the hydrophilic sites are a linear function of the pinning spot circumference. Protein samples prepared and deposited on the pinning sites for analysis by matrix-assisted laser desorption ionization indicate an improvement in sensitivity from that of a standard plate analysis by a factor of 5.     

Analysis of the acid and alkali resistance of superhydrophobic paper mulch

Agricultural paper mulch is an indispensable part of modern agriculture. It had the functions of heat preservation, moisture preservation, insect resistance, disease prevention, and weed growth inhibition. In order to extend the service life of the paper mulch, we use the solution immersion method to modify the surface of the paper mulch. A super-hydrophobic paper mulch is mainly prepared by using hydrophobic silica. The static contact angle of the super-hydrophobic paper mulch with water is 160.6°. The super-hydrophobic paper mulch samples were immersed in acid solution (pH?=?4.6 H₂SO₄) and alkaline solution (pH?=?8.5 NaOH). The main instruments are contact angle tester, tensile testing machine and high-speed camera. The hydrophobic properties, mechanical properties and rebound properties of the two kinds of paper mulches were compared. The results showed that the tensile strength and droplet bounce height of the superhydrophobic paper mulch decreased after being soaked in acid or alkaline solution for 48 h. The mass loss rate of paper mulch was more significant in acid solution, but its contact angle was still greater than 145°, and it had good bounce performance. After observing the microscopic morphology of its surface, it was found that silica had a micro-rough structure on the surface of the paper mulch. The method was simple and environmentally friendly, and can alleviate the problem of poor acid and alkali corrosion resistance of the paper mulch, and had extraordinary significance for environmental protection.

     

Transformation of hydrophobic surface into superhydrophobic surface by interfacial flower like silver films

Fabrication of superhydrophobic surface was achieved by electroless deposition of silver film and subsequent immersion into a mixture of stearic acid and cysteamine. The resultant superhydrophobic surface with flower and fall‐leaves like structure showed lotus leaf effect with the water contact angle of about 154° making copper surface water repellant. Copyright © 2014 John Wiley & Sons, Ltd.     

SDBS/HCl化学刻蚀法制备具有纳米-微米混合结构的铝基超疏水表面

采用阴离子表面活性剂十二烷基苯磺酸钠(SDBS)作为辅助刻蚀剂, 利用盐酸刻蚀, 在铝基质的表面形成了纳米-微米混合的粗糙结构; 化学刻蚀后的粗糙表面经过1H,1H,2H,2H-全氟癸烷基三乙氧基硅烷(FDTES)的修饰, 形成了接触角大于160°的超疏水表面. 扫描电镜表征结果显示, 所得到的超疏水表面具有纳米-微米混合结构; 基于此, 利用气泡辅助刻蚀机理初步解释了二级混合结构产生的原因, 认为是坑刻蚀和位错刻蚀的共同作用导致了混合结构的产生. 此外, 不同pH和长时间暴露实验证明所制备的铝基超疏水表面具有良好的稳定性.     

Fabrication of biomimetic superhydrophobic surfaces by a simple flame treatment method

A simple flame treatment method was explored to construct micro/nanostructures on a surface and then fabricate a biomimetic superhydrophobic surface at a relatively low cost. SiO₂‐containing polydimethylsiloxane (PDMS) was used as a substrate. The PDMS replicas with various micropatterned surfaces were fabricated using grass leaf, sand paper, and PET sheet with parallel groove geometry as templates via PDMS replica molding. The PDMS replica surfaces with micron structures and the surface of a flat PDMS sheet as a control sample were further treated by flame. The fabricated surfaces were characterized by scanning electron microscopy and water contact angle measurements. The effect of surface microstructures on the transparency of PDMS was also investigated. The studies indicate that the fine nanoscale structures can be produced on the surfaces of PDMS replicas and a flat PDMS sheet by a flame treatment method, and that the hierarchical surface roughness can be adjusted and controlled by varying the flame treatment time. The flame‐treated surfaces of PDMS replicas and a flat PDMS sheet possess superhydrophobicity and an ultra‐low sliding angle reaching a limiting value of 1°, and the anisotropic wettability of the PDMS replica surface with oriented microgroove structures can be greatly suppressed via flame treatment. The visible light transmittance of the flame‐treated flat PDMS surface decreases with prolonged flame treatment times. Copyright © 2016 John Wiley & Sons, Ltd.     

Effect of deposition parameters on the wettability and microstructure of superhydrophobic films with hierarchical micro-nano structures

Superhydrophobic films with hierarchical micro-nano structures were deposited on glass substrates by solution immersion method from a solution containing cobalt chloride, urea and cetyl trimethyl ammonium bromide (CTAB). Subsequently the films were hydrophobized with a low surface energy material like octadecanoic acid under ambient conditions resulting in superhydrophobic surfaces with water contact angle (WCA) of about 168° and contact angle hysteresis of 1°. The effect of deposition parameters such as solution composition, temperature, deposition time and alkanoic acid treatment on surface morphology and wettability of the films was studied. Mechanism of formation of cobalt chloride carbonate hydroxide film is discussed. Addition of CTAB to the solution resulted in a change in the surface morphology of the deposited films with flower-like structures. The wettability of films obtained under different process conditions was correlated to surface roughness using Wenzel and Cassie models.     

Application of Nano-Hydroxyapatite Derived from Oyster Shell in Fabricating Superhydrophobic Sponge for Efficient Oil/Water Separation

The exploration of nonhazardous nanoparticles to fabricate a template-driven superhydrophobic surface is of great ecological importance for oil/water separation in practice. In this work, nano-hydroxyapatite (nano-HAp) with good biocompatibility was easily developed from discarded oyster shells and well incorporated with polydimethylsiloxane (PDMS) to create a superhydrophobic surface on a polyurethane (PU) sponge using a facile solution–immersion method. The obtained nano-HAp coated PU (nano-HAp/PU) sponge exhibited both excellent oil/water selectivity with water contact angles of over 150° and higher absorption capacity for various organic solvents and oils than the original PU sponge, which can be assigned to the nano-HAp coating surface with rough microstructures. Moreover, the superhydrophobic nano-HAp/PU sponge was found to be mechanically stable with no obvious decrease of oil recovery capacity from water in 10 cycles. This work presented that the oyster shell could be a promising alternative to superhydrophobic coatings, which was not only beneficial to oil-containing wastewater treatment, but also favorable for sustainable aquaculture.