电位滴定法测定半胱氨酸和胱氨酸的研究及应用

本文报道了以Hg^2 为滴定剂,涂丝Ag-Ag2S电极指示,电位滴定法测定复杂体系中半胱氨酸和胱氨酸的新方法。滴定终点突跃明显,检测下限1mg／L,回收率97％～99％。方法简便、快捷、灵敏。     

利多卡因选择性涂丝电极稳定性的研究

涂丝电极问世已有十多年,可用于离子选择性场效应管^[1]、高效液相色谱检测器^[2],但稳定性差。一般认为涂丝电极的金属与PVC膜之间的电子传递是由不可逆电对Pt|O₂,H₂O所引起^[3],因此可以认为,这一电对的不可逆性以及在使用过程中O₂、H₂O活度的变化是造成涂丝电极稳定性差的根本原因。     

电解沉积制作复合Ag/Ag2S电极测定污水中氰化物

首先在玻璃毛细管外化学沉银,然后在银层上电解沉积Ag2S层,制得Ag/Ag2S固膜电极;与毛细管内的Ag/AgCl参比电极组装成复合电极系统。试验表明,该电极对CN-具有良好的能斯特响应,能斯特斜率约为110 mV/pCN-,线性范围为pCN-3~7,检测下限为5×10-8mol.L-1。应用此电极分析污水试样的结果与标准光度法的测定结果相符,两者的相对误差小于5.1%。试验了常见离子如S2-、Ag 、Hg2 等的干扰及其消除方法。讨论了电极的响应机理。     

半胱氨酸在Ag2S/Cu2S纳米晶修饰玻碳电极上的电化学行为

制备了Ag2S/Cu2S纳米混晶修饰玻碳电极,研究了半胱氨酸在Ag2S/Cu2S纳米混晶修饰电极上的电化学行为.结果表明:Ag2S/Cu2S混晶修饰电极对半胱氨酸的电化学氧化过程具有非常明显的电催化作用,其氧化电位减小为0.23V,氧化峰电流为25.98 μA,与空白电极相比增加了8倍.在1.0×10-5～1.0×10-3 mol/L浓度范围内,稳态电流信号与半胱氨酸浓度呈现良好的线性变化关系.该修饰电极具有良好的稳定性和重现性.     

双层聚合膜可乐定选择性涂丝电极的研究

报告一种新型双层聚合膜可乐定涂丝电极的研制。通过电化学聚合,在铂丝表面修饰一层具有导电性能的聚苯胺薄膜,外层涂PVC膜(含四苯硼酸-可乐定活性物质)。此种电极既保持了涂丝电极的优点,又具备较好的稳定性和重现性,连续测定8h,电位值漂移0.8mV,线性范围为1×10^-1～8×10^-6mol/L,电极响应斜率56.7mV/decade;用加入稀释法测定了回收率,平均回收率为100.9%,标准偏差为1.3%。     

基于氰化物对辣根过氧化物酶的抑制作用测定氰化物的研究

基于氰化物对辣根过氧化物酶(HRP)的抑制作用,将辣根过氧化物酶电极用于水中的微量氰化物的测定。酶电极制作中,先在金电极表面自组装一层半胱胺单层膜,再用戊二醛交联HRP。采用这种酶固定化方法,电极在6.0×10-5～4×10-3mol/LH2O2的浓度范围呈线性关系。探讨了工作电位、介体浓度、pH值、底物浓度等实验条件对酶电极性能及抑制过程中响应电流的影响,考察了电极的重现性、干扰及使用寿命。电极检测氰化物的线性范围为0.3～20μg/mL,检出限为100ng/mL,将电极用于水中CN-回收率的测定,结果良好。     

5—Br—PAN—S光度法测定微量锌的研究

研究了锌与5-Br-PAN-S的显色反应.在pH8.5,Zn(Ⅱ)与5-Br-PAN-S反应生成1:2的红色络合物,其最大吸收峰为568nm,表观摩尔吸光系数为4.80×10~4,Zn(Ⅱ)浓度在0～30μg/25ml服从比耳定律.用本法测定了水样和头发中的微量锌,结果满意.     

3D石墨烯/SiO2@Ru(bpy)2+3修饰电极电化学发光测定敌草隆的研究

利用敌草隆对三联吡啶钌电化学发光(ECL)的增敏作用,以3D石墨烯和二氧化硅固定三联吡啶钌纳米复合材料(SiO2@Ru(bpy)32+)修饰的玻碳电极为工作电极,建立了一种直接快速检测敌草隆的电化学发光新方法.通过一步水热法合成了3D石墨烯以促进电子传递,油包水微乳液法合成SiO2@Ru(bpy)32+以提高发光效率.在最佳实验条件下,敌草隆浓度的对数在9.08×10-11～9.08×10-7 mol/L范围内与其相对发光强度呈良好的线性关系(r2 =0.998 9),检出限(S/N=3)为1.18×10-12 mol/L.连续测定2.00×l0-8 mol/L敌草隆10次,发光强度值的相对标准偏差(RSD)为4.2％,表明该方法具有良好的重复性.用该方法对青菜进行检测,回收率为99.3％～ 110.8％,结果满意.     

去甲肾上腺素和抗坏血酸在导电聚合物膜修饰电极上的同时测定

采用循环伏安法研究去甲肾上腺素(NE)和抗坏血酸(AA)在4-(2-吡啶偶氮)间苯二酚(PAR)导电聚合膜修饰电极上的电化学行为;以差示脉冲伏安法(DPV)对二者进行测定,发现PAR修饰电极对NE和AA有很强电催化作用,明显增强了电极反应的可逆性及峰电流。在pH 6.0磷酸盐缓冲液(PBS)中,NE氧化峰电流与其浓度在6.25×10-7~6.25×10-5mol/L范围内呈良好的线性关系,AA氧化峰电流与其浓度在1.0×10-6~3.0×10-4mol/L范围内呈良好的线性关系,检出限分别为5.0×10-8mol/L和5.0×10-7mol/L。该PAR膜修饰电极可对NE和AA进行单独或同时的测定,并用于实际样品重酒石酸去甲肾上腺素针剂和维生素C针剂的检测。     

酪氨酸酶电流传感器测定低浓度氰化物抑制剂的研究

用预活化聚酰胺膜固定酪氨酸酶,制得性能良好的酪氨酸酶生物传感器,以此测定CN^-抑制剂的含量。在磷酸盐缓冲溶液中,以苯酚作底物,浓度范围为5×10^-6～4×10^-5mol/L,当苯酚浓度一定时,还原电流(-0.200V,vs,SCE)的下降值与CN^-浓度的平方根成线性关系,检测范围为5×10^-7～2×10^-4mol/L,有良好的选择性和重现性。     

Heterogeneous Membrane and Coated Wire Type Electrode with Chitosan as Ionophore in the Potentiometric Determination of Glutamate: Comparative Study

This study reports on two types of glutamate sensors based on chitosan, i) heterogeneous membrane and ii) coated wire (CWE). The linearity ranges are: i) membrane, 1.0×10^?5 to 1.0×10^?1 M and ii) CWE, 1.0×10^?5 to 1.0×10^?3 M. The LODs, and pH ranges are i) membrane, 5.0×10^?6 M and 4–8 and ii) CWE, 1.0×10^?5 M and 3–5, respectively. The presence of ionic species normally found in foodstuffs did not interfere in both electrodes. Interference in CWE was minimized by prior dilution of the sample. The CWE was further investigated for on‐line analysis. The material for proposed electrodes was cheaper and environmental friendly. Hence, they were suggested as alternative tools for the analysis of glutamate.     

聚乙烯醇缩丁醛膜涂丝酶电极构造方法的研究

本文以三月桂胺为中性载体制成聚乙烯醇缩丁醛膜涂丝pH电极,再以该pH电极为换能器,采用三种共价交联固定化酶方法制成涂丝乙酰胆碱酯酶电极。该酶电极能用于测定0.1～10mmol/L浓度范围内的乙酰胆碱,响应时间在3～6min之内,寿命可达两个多月。     

Selective Determination of Zn2+ Ion in Various Environmental,Biological and Medicinal Plant Samples Using a Novel Coated Graphite Electrode

Novel Zn²⁺ ion‐selective PVC based coated graphite electrodes were fabricated using the ionophores N‐((1H‐indol‐3‐yl)methylene)thiazol‐2‐amine (I₁), N‐((1H‐indol‐3‐yl)methyl)‐thiazol‐2‐amine (I₂) and 1‐((1H‐indol‐3‐yl)methylene)urea (I₃). Their potentiometric performance was examined in dependence of the addition of plasticizers and anion excluders and compared. It is found that the coated graphite electrode with the composition I₁:KTpClPB:o‐NPOE:PVC=9 : 1.5 : 51 : 38.5 is the best with respect to the wide working concentration range (4.2×10^?8–1.0×10^?1 mol L^?1), low detection limit (1.6×10^?8 mol L^?1) and wide pH range of 3.0–8.0. The proposed electrode was successfully applied to quantify Zn²⁺ in various environmental, biological and medicinal plant samples and used as indicator electrode.     

Electroanalytical Studies on Cobalt(II) Ion‐Selective Sensor of Polymeric Membrane Electrode and Coated Graphite Electrode Based on N2O2 Salen Ligands

Poly(vinyl chloride)‐based membranes of salen ligands, 2‐((E)‐((1R,2S)‐2‐((E)‐5‐tert‐butyl‐2‐hydroxybenzylideneamino)cyclohexylimino)methyl)‐4‐tert‐butyl phenol (S₁) and 2‐((E)‐((1R,2S)‐2‐((E)‐3,5‐di‐tert‐butyl‐2‐hydroxybenzylideneamino)cyclohexylimino)methyl)‐4,6‐di‐tert‐butylphenol (S₂) were fabricated and explored as cobalt(II) selective electrodes. The performance of the polymeric membrane electrode (PME) and coated graphite electrode (CGE) were compared and it was observed that CGE showed a wide working concentration range of 1.1×10^?8 to 1.0×10^?1 mol L^?1 with a limit of detection of 7.0×10^?9 mol L^?1 exhibiting the Nernstian slope 29.6 mV/decade of activity in the pH range 3.0–9.0. It was used for the determination of cobalt(II) ions in water, soil, beer, pharmaceutical samples and medicinal plants and would be used as an indicator electrode in potentiometric titration with EDTA.     

Construction of a New Uranyl‐Selective Electrode Based on a New Ionophore: Comparison of the Effect Additive on Electrode Responses

A new plasticized PVC uranyl‐selective electrode based on a bis(2‐hydroxyacetophenone)ethylenediimine (BHAED) carrier by the direct coating of the membrane ingredients on the surface of a graphite disk electrode is reported. The electrode displayed high selectivity for uranyl ion toward a number of inorganic ions. The influence of the membrane compositions and pH, the effect of lipophilic cationic and anionic additives and plasticizer on the response properties of the electrode were investigated. The electrode exhibited a Nernstian slope of + 29.3 ± 1.2 for the uranyl ion concentration in the range of 5.0 × 10^?6 ?0.05 M with detection limits of approx. 2.0 μM. The potentiometric responses of the electrode are independent of pH over the range of 3.0–4.5 with satisfactory reproducibility. The sensor has response times of <5 s and can be used for at least 2 months without considerable divergence in potential.     

反相胶束法控制合成不同形貌半导体Ag_2S纳米晶

采用水（溶液）／Triton X－100／环已烷／正戊醇反相胶束体系，制备出不 同形貌的Ag_2S纳米晶-100nm、长度为2.0-3.5μm、长径比为20-70的纯相幅S对合 成Ag_2S的形貌和尺寸的影响进行了研究，获得了控制合成不同形貌Ag_2S纳米晶的 反应条件．显微镜分析进行了表征．     

A Study on Adsorption of Electrogenerated Cystine Precipitate onto An Electrode using Electrochemical Quartz Crystal Impedance System

Insiluquartzcrystalimpedance(QCI)measurementduringelectrochemicalperturbationshasfoundwideapplicationsininvestigatingmetalandpolymerdepositionetc'-',asitprovidesmultidimensionalinsitupiezoelectricinformation.QCIanalysishasbeenbasedontheButterworth-VanDyke(BVD)equivalentelectricalcircuitcomposedofamotionalarmandastaticarminparallel.Themotionalarmcontainsthreeequivalentcircuitelementsinseries,namely,themotionalresistanceRI,themotionalinductanceL,andthemotionalcapacitanceC,,whilethestaticar…     

Preparation of the Ag2O2-PbO2 Modified Electrode and Its Application towards Escherichia coli Fast Counting in Water

A novel nano crystalline Ag2O2-PbO2 film chemically modified electrode (CME) was prepared and the CME was characterized by X-ray diffractometer (XRD) and atomic focrce microscope (AFM). By chronoamperometry, the nano Ag2O2-PbO2 CME was used as bioelectrochemical sensor to determine the population of Escherichia coli (E.coli) in water. Compared with conventional methods, it is found that the technique we used is fast and convenient in counting E.coil