Enhanced photocatalytic degradation of nitrobenzene using MWCNT/β-ZnMoO4 composites under UV light emitting diodes (LEDs)

The β-ZnMoO₄/MWCNT nanocrystal composites were synthesized using hydrothermal method. The physicochemical properties such as structure, morphology and bandgap of synthesized photocatalysts were characterized using PXRD, UV-vis DRS, FTIR, FT-Raman, SEM and TEM analytical methods. PXRD pattern shows the peak shift in the case of synthesized ZnMoO₄/MWCNT which confirms the formation of nanocomposites. Moreover, the strong absorbance in UV region which was evidenced in UV-vis DRS spectra for all the case of synthesized ZnMoO₄ and ZnMoO₄/MWCNT composites. From the SEM and TEM images, the MWCNT was found to have adhered over the ZnMoO₄ nanocrystals. Compared to bare β-ZnMoO₄, β-ZnMoO₄/MWCNT nanocrystal composites exhibited significant higher photocatalytic activity under ultraviolet light emitting diodes (UVLEDs) irradiation for the degradation of nitrobenzene (NB; 2.606 × 10^?4 M). This may be due to the effective charge transfer in the composite and optimized electron hole pair recombination. The photocatalytic activity of the synthesized photocatalysts was also studied under visible LEDs and it is observed that the photocatalytic degradation of NB was 97%, 77%, 65% and 52% under the irradiation of UV, blue, green, and red LEDs respectively.     

WO3 Quantum Dots Decorated GO/Mg‐doped ZnO Composites for Enhanced Photocatalytic Activity under Nature Sunlight

Graphene oxide/Mg‐doped ZnO/tungsten oxide quantum dots composites (WQGOMZ) were prepared through co‐precipitation method, and were studied by X‐ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X‐ray photoelectron spectroscopy (XPS), Fluorescence spectra (FL), and UV–vis diffuse reflection spectra. Furthermore, the photocatalytic activity of resultant WQGOMZ was evaluated under nature sunlight. Experimental results showed that WO₃QDs can remarkably heighten the photocatalytic activity of GOMZ composite, in which is nearly 6.58 times higher than that of GOMZ composite. Simultaneously, WQGOMZ composites possess optical memory ability and maintain high photocatalytic stability for more than 40 days. The enhanced photocatalytic activity and optical memory ability are attributed to the effective synergistic effect between ZnO and WO₃QDs.     

Comparison study of BiVO4 heterojunctions photocatalyst with different carbon materials

MWCNT/BiVO₄ and RGO/BiVO₄ heterojunctions were synthesized by the sol–gel method, and the photocatalytic activity of MWCNT/BiVO₄ and RGO/BiVO₄ were evaluated by monitoring the degradation of RhB in a heterogeneous photocatalytic reactor. The catalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy, scanning electron microscopy, Fourier-transform infrared spectroscopy and X-ray photoelectron spectroscopy. The results indicated that a series of heterojunction structure composites were successfully synthesized, the heterojunction structure playing a crucial role in the electron–hole recombination. The crystal structure of BiVO₄ was still monoclinic after the doping of MWCNT and RGO according to the XRD analysis, while the active sites of MWCNT/BiVO₄ and RGO/BiVO₄ were more than pure BiVO₄. The RGO with a two-dimensional carbon sheet expressed higher performance than MWCNT with a one-dimensional carbon sheet for BiVO₄ because the layered structure of the RGO had a stronger electron-trapping capability than MWCNT. The optimal MWCNT content was 2%, and the 6% RGO/BiVO₄ showed the highest photocatalytic degradation efficiency of RhB. The photocatalytic degradation efficiency remained above 80% after five cycle tests.

     

TiO2/carbon nanotube hybrid nanostructures: Solvothermal synthesis and their visible light photocatalytic activity

MWCNT/TiO₂ hybrid nanostructures were prepared via solvothermal synthesis and sol-gel method with benzyl alcohol as a surfactant. As-prepared hybrid materials were characterized by X-ray diffraction, transmission electron microscopy, UV-vis diffuse reflectance spectra and X-ray photoelectron spectroscopy. The results showed that MWCNTs were uniformly decorated with anatase nanocrystals in solvothermal condition, but MWCNTs were embedded in a majority of TiO₂ nanoparticles by sol-gel method. When the weight ratio of MWCNTs to TiO₂ was 20%, MWCNT/TiO₂ hybrid nanostructures prepared by solvothermal synthesis exhibited higher visible-light-driven photocatalytic activity than that prepared by sol-gel method. Post-annealing of MWCNT/TiO₂ nanostructures at 400 °C resulted in the formation of the carbonaceous Ti-C bonds on the interface between TiO₂ and MWCNTs, which enhanced the photoabsorbance of the hybrid materials in the visible light region and improved the visible-light degradation efficiency of methylene blue.     

Influence of modification of MWCNTs on the structure and performance of MWCNT‐Poly(MMA‐AM) hybrid membranes

Hybrid membranes containing multi‐walled carbon nanotubes (MWCNTs) were initially prepared to separate benzene/cyclohexane mixtures. Subsequently, MWCNT surfaces were chemically modified using two methods to change the surface polarity of the MWCNTs and improve the distribution thereof in Poly(methylmethacrylate) (PMMA). This change consequently enhanced the separation performance of hybrid membranes with MWCNTs. Raman spectroscopy was used to characterize the structure of the pristine MWCNTs and the modified MWCNTs. The morphology and distribution of the MWCNTs in PMMA were investigated by transmission electron microscopy. The results showed that the addition of MWCNTs clearly improved the separation performance of the hybrid membranes. Surface modification introduced polar groups onto the MWCNT surface, which significantly improved the distribution of MWCNTs in the PMMA membranes and the performance of hybrid membranes. MWCNTs with higher surface polarity also increased the amount of MWCNTs distributed homogeneously in PMMA. Aminated MWCNTs (MWCNT‐NH₂) showed the highest surface polarity. Thus, the content of MWCNT‐NH₂ well distributed in PMMA was the highest among the three types of MWCNTs. The highest separation factor for the hybrid membranes with 1.0 wt% MWCNT‐NH₂ was about seven times that of membranes containing pristine MWCNTs. Copyright © 2013 John Wiley & Sons, Ltd.     

Binary Au/MWCNT and Ternary Au/ZnO/MWCNT Nanocomposites: Synthesis,Characterisation and Catalytic Performance

Gold nanoparticles of 10–24 and 5–8 nm in size were obtained by chemical citrate reduction and UV photoreduction, respectively, on acid‐treated multiwalled carbon nanotubes (MWCNTs) and on ZnO/MWCNT composites. The shape and size of the deposited Au nanoparticles were found to be dependent upon the synthetic method used. Single‐crystalline, hexagonal gold particles were produced in the case of UV photoreduction on ZnO/MWCNT, whereas spherical Au particles were deposited on MWCNT when the chemical citrate reduction method was used. In the UV photoreduction route, n‐doped ZnO serves as the e^? donor, whereas the solvent is the hole trap. All materials were fully characterised by UV/Vis spectroscopy, scanning electron microscopy, transmission electron microscopy, X‐ray photoelectron spectroscopy, Raman spectroscopy and BET surface analysis. The catalytic activity of the composites was studied for the selective hydrogenation of α,β‐unsaturated carbonyl compound 3,7‐dimethyl‐2,6‐octadienal (citral). The Au/ZnO/MWCNT composite favours the formation of unsaturated alcohols (selectivity=50 % at a citral conversion of 20 %) due to the presence of single‐crystalline, hexagonal gold particles, whereas saturated aldehyde formation is favoured in the case of the Au/MWCNT nanocomposite that contains spherical gold particles.     

Effects of electrically inert fillers on the properties of poly(<Emphasis Type="Italic">m</Emphasis>-xylene adipamide)/multiwalled carbon nanotube composites

The effects of three types of electrically-inert fillers, calcium carbonate (CaCO₃), talc and glass fiber (GF), on electrical resistivity, crystallization behavior and dynamic mechanical properties of poly(m-xylene adipamide) (MXD6)/multiwalled carbon nanotube (MWCNT) composites are investigated. The electrical resistivity of MXD6/MWCNT composites is significantly reduced with the addition of inert fillers due to the volume-exclusion effect that leads to increased effective concentration of MWCNTs in MXD6 matrix and also due to improved MWCNT dispersion. The crystallization temperature of MXD6 increases with the addition of MWCNTs, indicating that MWCNTs can act as nucleating agent and induce crystallization of MXD6. The incorporation of inert fillers has no further effect on crystallization behavior of MXD6, but significantly improves the storage modulus of MXD6/MWCNT composite, demonstrating that CaCO₃, talc and GF filled MXD6/MWCNT composites are very promising materials with not only improved electrical property but also excellent mechanical properties.     

Synthesis,characterization, and electrical properties of polypyrrole/multiwalled carbon nanotube composites

Size‐controllable polypyrrole (PPy)/multiwalled carbon nanotube (MWCNT) composites have been synthesized by in situ chemical oxidation polymerization directed by various concentrations of cationic surfactant cetyltrimethylammonium bromide (CTAB). Raman spectra, FTIR, SEM, and TEM were used to characterize their structure and morphology. These results showed that the composites are core (MWCNT)–shell (PPy) tubular structures with the thickness of the PPy layer in the range of 20–40 nm, depending on the concentration of CTAB. Raman and FTIR spectra of the composites are almost identical to those of PPy alone. The electrical conductivities of these composites are 1–2 orders of magnitude higher than those of PPy without MWCNTs. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6449–6457, 2006     

Synthesis,Characterization and Photocatalytic Activity of Mg‐Impregnated ZnO–SnO2 Coupled Nanoparticles

ZnO–SnO₂ nanoparticles were prepared by coprecipitation method; then Mg, with different molar ratios and calcination temperatures, was loaded on the coupled nanoparticles by impregnation method. The synthesized nanoparticles were characterized by X‐ray diffraction (XRD), field emission scanning electron microscopy (FESEM), energy dispersive X‐ray spectroscopy (EDX), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS), and Brunauer–Emmett–Teller (BET) techniques. Based on XRD results, the ZnO–SnO₂ and Mg/ZnO–SnO₂ nanoparticles were made of ZnO and SnO₂ nanocrystallites. According to DRS spectra, the band gap energy value of 3.13 and 3.18 eV were obtained for ZnO–SnO₂ and Mg/ZnO–SnO₂ nanoparticles, respectively. BET analysis revealed a Type III isotherm with a microporous structure and surface area of 32.051 and 49.065 m² g^?1 for ZnO–SnO₂ and Mg/ZnO–SnO₂, respectively. Also, the spherical shape of nanocrystallites was deduced from TEM and FESEM images. The photocatalytic performance of pure ZnO–SnO₂ and Mg/ZnO–SnO₂ was analyzed in the photocatalytic removal of methyl orange (MO). The results indicated that Mg/ZnO–SnO₂ exhibited superior photocatalytic activity to bare ZnO–SnO₂ photocatalyst due to high surface area, increased MO adsorption and larger band gap energy. Maximum photocatalytic activity of Mg/ZnO–SnO₂ nanoparticles was obtained with 0.8 mol% Mg and calcination temperature of 350°C.     

Heterostructured MgO/ZnO photocatalysts: Synthesis,Characterization and UV Light-Induced Photocatalytic Activity Using Model Pollutant 2,6-dichlorophenol

ZnO and MgO/ZnO (mass ratio 2: 5, 5: 5 and 8: 5) heterostructure photocatalysts (Mg₂Zn₅, Mg₅Zn₅ and Mg₈Zn₅, respectively) were successfully synthesized via co-precipitation method. MgO/ZnO composites were characterized by scanning electron microscopy (SEM), X-Ray diffraction and low temperature nitrogen adsorption–desorption isotherm. According to SEM images all composites consisted of spherical granules with particle sizes of 30–50 nm. The band gap value of ZnO was found to be lower than that of MgO/ZnO composites as observed during the optical studies. Pure ZnO showed lower photocatalytic activity (38%) in the degradation of 2,6-dichlorophenol (2,6-DCP) than MgO/ZnO composites. Mg₅Zn₅ composite with a higher concentration of defects in crystallites was more active in the photocatalytic degradation (79.5%) than Mg₈Zn₅ (61.2%) and Mg₂Zn₅ (63.5%). High-resolution mass spectrometry-and UV-Vis spectroscopic analysis of the by-products, derived from model pollutant 2,6-DCP, proved the successful photocatalytic performance of Mg₅Zn₅ under the UV light. The synthesized composites are future candidates against other potential environmental pollutants.     

Dielectric Response of Bi4Ti3O12/PVDF Composite Electrodes for Energy Storage

This study is reporting the role of embedded ferroelectric ceramics Bi₄Ti₃O₁₂ (BTO = 1–5 wt%) into the polyvinylidene fluoride (PVDF) composites on its structural, bonding, surface morphology, and dielectric response. Especially lead free flexible composite electrodes have lot of attention due to its high dielectric permittivity and energy storage density. X-ray diffraction spectra confirms monophasic orthorhombic structure of composites, while Fourier transform infrared (FTIR) spectra confirms the bonding behavior. Scanning electron microscopy (SEM) images surface morphology of homogeneously distributed ceramic particles with interconnected network. Dielectric constant has been found to be improved from 9.56 to 13.73 for BTO_5%PVDF_95% composites at frequency of 1 kHz attributes promoted interfacial polarization of PVDF and effectively limited the charge leakage in the composites, implying promising applications in flexible electronic devices.     

Decoration of MWCNTs with CoFe2O4 Nanoparticles for Methylene Blue Dye Adsorption

In the present work, a simple and viable method for producing multi-walled carbon nanotubes (MWCNTs) decorated with CoFe₂O₄ nanoparticles is presented. Chemical composition and crystal structure of the CoFe₂O₄/MWCNT composite was confirmed by X-ray diffraction measurements, while transmission electron microscopy was used to characterize the morphology and the distribution of nanocrystals in the composite. The obtained particles with relatively small diameter (about 14.9?nm) were found to be dispersed on the carbon nanotubes. The adsorption of methylene blue dye on CoFe₂O₄/MWCNT composites has been investigated. CoFe₂O₄/MWCNT composites show high adsorption capacity for methylene blue dye. Both Langmuir and Freundlich models describe the adsorption isotherms very well and the adsorption thermodynamic parameters (?G ⁰, ?H ⁰ and ?S ⁰) were calculated. The adsorption of methylene blue is generally spontaneous and thermodynamically favorable. The adsorption of methylene blue involves an endothermic process.     

Facile Synthesis of Ag/Ag3PO4 Composites with Highly Efficient and Stable Photocatalytic Performance under Visible Light

The Ag/Ag₃PO₄ composites with various shapes (spheres, polyhedral, and microcubes) were synthesized by a facile precipitation method and a subsequent light‐reduction route at room temperature. The as‐prepared Ag/Ag₃PO₄ composites were characterized in detail by X‐ray diffraction, Fourier transform infrared spectra, X‐ray photoelectron spectroscopy, scanning electron microscopy, UV–vis diffuse reflection, and photoluminescence spectroscopy. The growth processes of different morphologies Ag/Ag₃PO₄ composites are also discussed. The decomposition test of rhodamine B (RhB) indicated that the Ag/Ag₃PO₄ composites enhanced the photocatalytic performance compared with pure Ag₃PO₄, which was attributed to the surface plasmon resonance (SPR) of Ag nanoparticles and the stability of the photocatalysts. Moreover, uniform cubes of Ag/Ag₃PO₄ showed the highest photocatalytic activity and could completely degrade RhB in 7 min, which could be primarily ascribed to the cubic structure of Ag/Ag₃PO₄ with strong visible‐light absorption and efficient separation of the photo‐generated electrons and holes. Furthermore, the possible photocatalytic mechanism is also discussed.     

One pot synthesis of Ag nanoparticle modified ZnO microspheres in ethylene glycol medium and their enhanced photocatalytic performance

Ag nanoparticles (NPs) modified ZnO microspheres (Ag/ZnO microspheres) were prepared by a facile one pot strategy in ethylene glycol (EG) medium. The EG played two important roles in the synthesis: it could act as a reaction media for the formation of ZnO and reduce Ag⁺ to Ag⁰. A series of the characterizations indicated the successful combination of Ag NPs with ZnO microspheres. It was shown that Ag modification could greatly enhance the photocatalytic efficiency of ZnO microspheres by taking the photodegradation of Rhodamine B as a model reaction. With appropriate ratio of Ag and ZnO, Ag/ZnO microspheres showed the better photocatalytic performance than commercial Degussa P-25 TiO₂. Photoluminescence and surface photovoltage spectra demonstrated that Ag modification could effectively inhibit the recombination of the photoinduced electron and holes of ZnO. This is responsible for the higher photocatalytic activity of Ag/ZnO composites.     

Synthesis of BiVO4 nanosheets-graphene composites toward improved visible light photoactivity

Two-dimensional (2-D) BiVO₄ nanosheets-graphene (GR) composites with different weight addition ratios of GR have been prepared via a facile wet chemistry process. X-ray diffraction (XRD), Raman spectra, X-ray photoelectron spectra (XPS), UV-vis diffuse reflectance spectra (DRS), field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), nitrogen adsorption-desorption, transient photocurrent response and photoluminescence (PL) spectra were employed to determine the properties of the samples. It is found that BiVO₄ nanosheets could pave well on the surface of graphene sheets. BiVO₄ nanosheets-GR composites with a proper addition amount of GR exhibited higher photocatalytic activity than bare BiVO₄ nanosheets toward liquid-phase degradation of rhodamine B (RhB) and methyl orange (MO) under visible light irradiation. The enhancement of photocatalytic activities of BiVO₄ nanosheets-GR composites can be attributed to the effective separation of photoexcited electron-hole pairs. This work not only provides a simple strategy for fabricating specific 2-D semiconductor-2-D GR composites, but also opens a new window of such 2-D semiconductor-2-D GR composites as visible light photocatalysts toward an improved visible light photoactivity in purifying polluted water resources.     

Preparation and Characterization of In-Situ Polymerized Nanocomposites Based on Polyaniline in Presence of MWCNTs

Summary: Polyaniline (PANI) composites were prepared with both unmodified and amine modified MWCNTs with and without BaTiO₃ through in-situ oxidative polymerization. Uniform coating of PANI on the MWCNTs and BaTiO₃ surfaces was found which was evident from the Field Emission Scanning Electron Microscopic (FESEM) and High Resolution Transmission Electron Microscopic (HRTEM) images. The structure of pure and amine modified MWCNTs was identified by Fourier Transform Infrared Spectroscopy (FTIR). The thermal stability of the amine modified composite with BaTiO₃ is higher than that of the unmodified composite because of the better affinity between modified MWCNTs and polymer matrix and due to the higher stability of barium titanate itself. The capacitance of amine modified MWCNTs and BaTiO₃ composites was less than that of the pure MWCNTs composites but the thermal stability increased in amine modified MWCNTs and BaTiO₃ composites with respect to the pure MWCNTs composites. The maximum capacitance and energy density values were found in MWCNT/PANI composites which were equal to 523.20 F/g and 142.83 Wh/kg respectively at a scan rate of 10mv/s. Maximum power density was found to be 5147.70 W/kg in the same composite at a scan rate of 200 mv/s.     

Fe2O3/ZnO/ZnFe2O4 composites for the efficient photocatalytic degradation of organic dyes under visible light

In this study, novel ternary Fe₂O₃/ZnO/ZnFe₂O₄ (ZFO) composites were successfully prepared through a simple hydrothermal reaction with subsequent thermal treatment. The as-prepared products were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Brunauer-Emmett-Teller (BET) analysis, Barrett-Joyner-Halenda (BJH) measurement, and UV–vis diffuse reflectance spectroscopy (UV–vis DRS). The photocatalytic degradation of rhodamine B (Rh B) under visible light irradiation indicated that the ZFO composites calcined at 500 °C has the best photocatalytic activity (the photocatalytic degradation efficiency can reach up to 95.7% within 60 min) and can maintain a stable photocatalytic degradation efficiency for at least three cycles. In addition, the photocatalytic activity of ZFO composites toward dye decomposition follows the order cationic Rh B > anionic methyl orange. Finally, using different scavengers, superoxide and hydroxyl radicals were identified as the primary active species during the degradation reaction of Rh B.     

Photocatalytic degradation of organic dyes by Er<Superscript>3+</Superscript>: YAlO<Subscript>3</Subscript>/Co- and Fe-doped ZnO coated composites under solar irradiation

In this work, the Er³⁺: YAlO₃/Co- and Fe-doped ZnO coated composites were prepared by the sol-gel method. Then, they were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy dispersive X-ray spectroscopy (EDX). Photo-degradation of azo fuchsine (AF) as a model dye under solar light irradiation was studied to evaluate the photocatalytic activity of the Er³⁺: YAlO₃/Co- and Fe-doped ZnO coated composites. It was found that the photocatalytic activity of Co- and Fe-doped ZnO composites can be obviously enhanced by upconversion luminescence agent (Er³⁺: YAlO₃). Besides, the photocatalytic activity of Er³⁺: YAlO₃/Fe-doped ZnO is better than that of Er³⁺: YAlO₃/Co-doped ZnO. The influence of experiment conditions, such as the concentration of Er³⁺: YAlO₃, heat-treatment temperature and time on the photocatalytic activity of the Er³⁺: YAlO₃/Co- and Fe-doped ZnO coated composites was studied. In addition, the effects of solar light irradiation time, dye initial concentration, Er³⁺: YAlO₃/Co- and Fe-doped ZnO amount on the photocatalytic degradation of azo fuchsine in aqueous solution were investigated in detail. Simultaneously, some other organic dyes, such as Methyl Orange (MO), Rhodamine B (RM-B), Acid Red B (AR-B), Congo Red (CR), and Methyl Blue (MB) were also studied. The possible excitation principle of Er³⁺: YAlO₃/Co- and Fe-doped ZnO coated composites under solar light irradiation and the photocatalytic degradation mechanism of organic dyes were discussed.     

Synthesis of metal (Fe or Pd)/alloy (Fe–Pd)‐nanoparticles‐embedded multiwall carbon nanotube/sulfonated polyaniline composites by γ irradiation

Composites of multiwall carbon nanotubes (MWCNTs) and sulfonated polyaniline (SPAN) were prepared through the oxidative polymerization of a mixture of aniline, 2,5‐diaminobenzene sulfonic acid, and MWCNTs. Fe, Pd, or Fe–Pd alloy nanoparticles were embedded into the MWCNT–SPAN matrix by the reduction of Fe, Pd, or a mixture of Fe and Pd ions with γ radiation. Sulfonic acid groups and the emeraldine form of backbone units in SPAN served as the source for the reduction of the metal ions in the presence of γ radiation. The existence of metallic/alloy particles in the MWCNT–SPAN matrix was further ascertained through characterization by high‐resolution transmission electron microscopy (HRTEM), Fourier transform infrared spectroscopy, ultraviolet–visible spectroscopy, thermogravimetric analysis, and conductivity measurements. HRTEM pictures clearly revealed the existence of Fe, Pd, and Fe–Pd nanoparticles of various sizes in the MWCNT–SPAN matrices. There were changes in the electronic properties of the MWCNT–SPAN–M composites due to the interaction between the metal nanoparticles and MWCNT–SPAN. Metal‐nanoparticle‐loaded MWCNT–SPAN composites (MWCNT–SPAN–M; M = Fe, Pd, or Fe–Pd alloy) showed better thermal stability than the pristine polymers. The conductivity of the MWCNT–SPAN–M composites was approximately 1.5 S cm^?1, which was much higher than that of SPAN (2.46 × 10^?4 S cm^?1). Metal/alloy‐nanoparticle‐embedded, MWCNT‐based composite materials are expected to find applications in molecular electronics and other fields. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3355–3364, 2006     

In situ polymerization of methyl methacrylate/multi-walled carbon nanotube composites using cationic stearyl methacrylate copolymers as dispersants

Novel water-soluble amphiphilic copolymers (poly[(stearyl methacrylate)-stat-([2-(methacryloyloxy)ethyl] trimethyl ammonium iodide)]) for dispersing multi-walled carbon nanotubes (MWCNTs) were used to carry out in situ methyl methacrylate (MMA) polymerization. The morphology of the poly(methyl methacrylate)/MWCNT composites and the dispersion of the MWCNTs were analyzed by transmission electron microscopy. The dispersion of multi-walled carbon nanotubes in the composites was excellent for cationic SMA (stearyl methacrylate) copolymers, even at high MWCNT loading (6.0 wt.%). The mechanical properties and electrical and thermal conductivities of the composites were also analyzed. Mechanical properties were improved by MWCNTs; the strain at break values remained stable up to 6.0 wt.% MWCNT loading. Both electrical and thermal conductivities were improved by the addition of MWCNTs.