Ultrasonic assisted fabrication of silver tungstate encrusted polypyrrole nanocomposite for effective photocatalytic and electrocatalytic applications

Ultrasonication is an emerging and evergreen technique for the efficient synthesis of the catalytically active heterostructured materials. In-situ one-pot ultrasonic-assisted synthesis method was demonstrated in this work for the fabrication of silver tungstate encrusted polypyrrole nanocomposite using semi-automatic ultrasonic probe maintained at 34°C/50 kHz ultrasonic frequency and at 150 W ultrasonic power. This material retains enhanced optical, electrical, morphological properties, photocatalytic behavior in photodegradation of congo red dye, tetracycline drug and its electrochemical sensing potential for the effective determination of a broad spectrum of antibacterial drug, nitrofurazone. Optical properties were investigated using UltraViolet–Visible diffuse reflectance spectral (UV–VIS DRS) data along with Tauc’s bandgap energy calculations. The morphological properties were examined using FESEM and TEM micrographs. All the PXRD and XPS details prove the effective distribution of PPy on the surface of Ag₂WO₄ rods with the help of powerful ultrasonic assistance. PPy acted as a support for nucleation and growth of Ag₂WO₄ and an inhibitor of phase transformations. Ag₂WO₄/PPy exhibits great photocatalytic behavior while comparing with pure PPy and Ag₂WO₄ in the degradation of carcinogenic dye congo red and antibiotic drug tetracycline. In addition to that, Ag₂WO₄/PPy modified GCE exposed a widespread linear range from 0.1 to 107 µM along with a very low detection limit of 12 nM and huge sensitivity of 1.74 µA µM⁻¹cm⁻² in the electrochemical determination of nitrofurazone.     

Preparation/Property Relationships for a Nitrate Amperometric Sensor: Effect of Nanowires Polymerization Parameters

Nitrate amperometric sensors based on polypyrrole (PPy) nanowire modified electrodes were developed by electropolymerization of pyrrole with a template‐free method. Polymerization parameters of PPy nanowires were changed to improve the amperometric response to NO₃ ^?. The experimental results show that the polymerization parameters such as concentration of pyrrole, concentration of electrolyte, acidity of polymerization solution, and the kinds and concentration of dopants have significant effects on the morphologies of the nanowires and the electroreduction current density of NO₃ ^?. The PPy nanowires prepared in a solution containing NO₃ ^? have an obvious “memory effect” for NO₃ ^?. The determination sensitivity and detection limit may be varied with the change of modification parameters. The PPy nanowire modified electrode prepared under a certain polymerization condition has good electrocatalytic effect toward electroreduction of NO₃ ^? and has good linearity between the electroreduction current density and the concentration of NO₃ ^?. The sensitivity and detection limit are 606.54 mA/M cm² and 9.98×10^?6 M, respectively.     

A sonochemical synthesis of SrTiO3 supported N-doped graphene oxide as a highly efficient electrocatalyst for electrochemical reduction of a chemotherapeutic drug

A sonochemical based green synthesis method playa powerful role in nanomaterials and composite development. In this work, we developed a perovskite type of strontium titanate via sonochemical process. SrTiO₃ particles were incorporated with nitrogen doped graphene oxide through simple ultrasonic irradiation method. The SrTiO₃/NGO was characterized by various analytical methods. The nanocomposite of SrTiO₃/NGO was modified with laser-induced graphene electrode (LIGE). The SrTiO₃/NGO/LIGE was applied for electrochemical sensor towards chemotherapeutic drug detection (nilutamide). Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) techniques have been used to examine the electrochemical performance of nilutamide (anti-cancer drug). DPV was found to be more sensitive and found to exhibit a sensitivity 8.627 µA µM⁻¹ cm⁻² for SrTiO₃/NGO/LIGE with a wide linear range (0.02–892 µM) and low Limit of detection (LOD: 1.16 µM). SrTiO₃/NGO/LIGE has been examined for the detection of nilutamide in blood serum and urine samples and obtained a good recovery in the range of 97.2–99.72 %. The enhanced stability and selectivity and practical application results indicates the suitability of SrTiO₃/NGO/LIGE towards the detection of nilutamide drug in pharmaceutical industries.     

Improved performance of silicon‐nanoparticle film‐coated dye‐sensitized solar cells

Silicon (Si) nanoparticles with average size of 13 nm and orange–red luminescence under UV absorption were synthesized using electrochemical etching of silicon wafers. A film of Si nanoparticles with thickness of 0.75 µm to 2.6 µm was coated on the glass (TiO₂ side) of a dye‐sensitized solar cell (DSSC). The cell exhibited nearly 9% enhancement in power conversion efficiency (η) at film thickness of ～2.4 µm under solar irradiation of 100 mW/cm² (AM 1.5) with improved fill factor and short‐circuit current density. This study revealed for the first time that the Si‐nanoparticle film converting UV into visible light and helping in homogeneous irradiation, can be utilized for improving the efficiency of the DSSCs. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

High vertical breakdown strength in with low specific on‐resistance AlGaN/AlN/GaN HEMTs on silicon

Off‐state and vertical breakdown characteristics of AlGaN/AlN/GaN high‐electron‐mobility transistors (HEMTs) on high‐resistivity (HR)‐Si substrate were investigated and analysed. Three‐terminal off‐state breakdown (BV_gd) was measured as a function of gate–drain spacing (L_gd). The saturation of BV_gd with L_gd is because of increased gate leakage current. HEMTs with L_gd = 6 µm exhibited a specific on‐resistance R_DS[ON] of 0.45 mΩ cm². The figure of merit (FOM = BV_gd²/R_DS[ON]) is as high as 2.0 × 10⁸ V² Ω^–1 cm^–2, the highest among the reported values for GaN HEMTs on Si substrate. A vertical breakdown of ～1000 V was observed on 1.2 µm thick buffer GaN/AlN grown on Si substrate. The occurrence of high breakdown voltage is due to the high quality of GaN/AlN buffer layers on Si substrate with reduced threading dislocations which has been confirmed by transmission electron microscopy (TEM). This indicates that the AlGaN/AlN/GaN HEMT with 1.2 µm thick GaN/AlN buffer on Si substrate is promising candidate for high‐power and high‐speed switching device applications. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Monodisperse Polypyrrole Nanoparticles Prepared via γ‐Ray Radiolysis of Water: An Efficient Near‐Infrared Photothermal Agent for Cancer Therapy

Biosafe nanoparticles with strong near‐infrared (NIR) light photothermal conversion effect can bring effective hyperthermia as one of the promising approaches in cancer therapy. In this work, a new facile and green preparation method of polypyrrole (PPy) nanoparticles based on ⁶⁰Co γ‐ray radiation on a simple air‐saturated strong acidic aqueous solution of pyrrole (pH ≤ 1) is studied. According to the MCAP‐FACSIMILE simulation on the concentrations of the radiolysis products of water at the presence of H⁺ and O₂, the main strong oxidative radiolysis products · OH and H₂O₂ rapidly induce the polymerization of pyrrole. The size of the prepared PPy nanoparticles is about several tens of nanometers and can be controlled by the pH, the concentration of the stabilizer poly(vinyl alcohol), and the absorbed dose rate (the amount of energy absorbed per unit mass of the irradiated material within per unit of time). The PPy nanoparticles show rapid and remarkable NIR (808 nm) photothermal conversion efficiency up to 40.1% in water. Furthermore, the in vitro and in vivo experiments confirm that the prepared PPy nanoparticles exhibit enough strong NIR photothermal effect in tumor cells (4T1 and HeLa) and show a promising prospect as the NIR photothermal agent for the future cancer therapy.     

Raman‐induced Kerr effect spectroscopy of single‐wall carbon nanotubes aqueous suspensions in the range 0.1–10 and 100–250 cm−1

Here, we study a low (less than 0.1 µg/ml) concentration aqueous suspension of single‐wall carbon nanotubes (SWNTs) by Raman‐induced Kerr effect spectroscopy (RIKES) in the spectral bands 0.1–10 and 100–250 cm⁻¹. This method is capable of carrying out direct investigation of SWNT hydration layers. A comparison of RIKES spectra of SWNT aqueous suspension and that of milli‐Q water shows a considerable growth in the intensity of low wavenumber Raman modes. These modes in the 0.1–10 cm⁻¹ range are attributed to the rotational transitions of H₂O₂ and H₂O molecules. We explain the observed intensity increase as due to the production of hydrogen peroxide and the formation of a low‐density depletion layer on the water–nanotube interface. A few SWNT radial breathing modes (RBM)are observed (ω_RBM = 118.5, 164.7 and 233.5 cm⁻¹) in aqueous suspension, which allows us to estimate the SWNT diameters (∼2.0, 1.5, and 1 nm, respectively). Copyright © 2011 John Wiley & Sons, Ltd.     

In Situ Synthesis and Characterization of Polypyrrole/Graphene Conductive Nanocomposites via Electrochemical Polymerization and Chemical Reduction

Polypyrrole/graphene sheets (PPy/GNs) nanocomposite electrodes were in- situ synthesized via electrochemical polymerization and chemical reduction from pyrrole (Py) and graphene oxide (GO). The surface morphologies of the nanocomposites were observed by scanning electron microscopy (SEM). The SEM results showed graphene sheets (GNs) scattered on the surface of the polypyrrole (PPy), and the morphologies of PPy/GNs nanocomposites manufactured by pulse current (PC-PPy/GNs) or direct current (DC-PPy/GNs) were smoother than that of PC-PPy. The electrochemical capacitance properties of the nanocomposite films were measured by cyclic voltammetry (CV), galvanostatic charge and discharge (GC), and electrochemical impedance spectroscopy (EIS) techniques in 3 mol·L^?1 KCl aqueous solutions. The results indicated that the specific capacitance of the DC-PPy/GNs nanocomposite was 13.5% higher than that of a PC-PPy electrode. Comparison of the electrochemical performance of the nanocomposites indicated that the PC-PPy/GNs nanocomposite had higher specific capacitance and better charging/discharging capability than that of the DC-PPy/GNs nanocomposite. The specific capacitance of the PC-PPy/GNs nanocomposite could reach to 280 F·g^?1 at a scanning rate of 100 mV·s^?1.     

Large enhancement of the thermoelectric Seebeck coefficient for amorphous oxide semiconductor superlattices with extremely thin conductive layers

Herein we demonstrate that amorphous oxide semiconductor (AOS) superlattices composed of a‐In–Zn–O (well) and a‐In–Ga–Zn–O (barrier) layers, fabricated on SiO₂ glass substrate by pulsed laser deposition at room temperature, exhibited an enhanced Seebeck coefficient |S |. The |S | value increases drastically with decreasing a‐In–Zn–O thickness (d_IZO) when d_IZO < ∼5 nm, and reached 73 µV K^–1 (d_IZO = 0.3 nm), which is ∼4 times larger than that of bulk |S |_3D (19 µV K^–1), while it kept its high electrical conductivity, clearly demonstrating that the quantum size effect can be utilized in AOS superlattices. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

The synthesis of Ag/polypyrrole coaxial nanocables via ion adsorption method using different oxidants

Ag/polypyrrole (PPy) coaxial nanocables (NCs) were synthesized by an ion adsorption method. In this method, the pre-made Ag nanowires (NWs) were dispersed in the aqueous solution of copper acetate (Cu(Ac)₂), and the Cu²⁺ ions adsorbed onto the surface of Ag NWs can oxidize pyrrole monomers to polymerize into uniform PPy sheath outside Ag NWs after the Cu(Ac)₂-treated Ag NWs were re-dispersed in the aqueous solution of pyrrole. The morphology of NCs was characterized by transmission electron microscope (TEM) and scanning electron microscope (SEM). The relationship between the thickness of polymer sheath and the concentration of Cu(Ac)₂ was established. As Cu(Ac)₂ which served as the oxidant can also be replaced by AgNO₃ in this synthesis, the differences on the structure of polymer sheath caused by different oxidants were studied by surface-enhanced Raman scattering (SERS), high-resolution transmission electron microscope (HR-TEM), Fourier transform infrared spectroscopy (FT-IR), and X-ray photoelectron spectroscopy (XPS). Comparing with the characterization results of Ag/PPy NCs synthesized using AgNO₃ as the oxidant which indicates the random arrangement of PPy chains at the interface between polymer sheath and Ag NWs, PPy chain oxidized by Cu²⁺ tends to show a relatively ordered conformation at the interface with the pyrrole rings identically taking the plane vertical to the surface of Ag NWs. In addition, although the main part of the polymer sheath was composed of PPy whatever kind of oxidant was used, the sheath of the NCs oxidized by Cu²⁺ is typical for the existence of Cu(I)–pyrrole coordinate structures with strong Cu(I)–N bond signal shown in XPS characterization.     

Food additives characterization by infrared,Raman, and surface‐enhanced Raman spectroscopies

Fourier‐transform infrared (FT‐IR), Raman (RS), and surface‐enhanced Raman scattering (SERS) spectra of β‐hydroxy‐β‐methylobutanoic acid (HMB), L ‐carnitine, and N‐methylglycocyamine (creatine) have been measured. The SERS spectra have been taken from species adsorbed on a colloidal silver surface. The respective FT‐IR and RS band assignments (solid‐state samples) based on the literature data have been proposed. The strongest absorptions in the FT‐IR spectrum of creatine are observed at 1398, 1615, and 1699 cm⁻¹, which are due to ν_s(COOH) + ν(CN) + δ(CN), ρ_s(NH₂), and ν(C O) modes, respectively, whereas those of L ‐carnitine (at 1396/1586 cm⁻¹ and 1480 cm⁻¹) and HMB (at 1405/1555/1585 cm⁻¹ and 1437–1473 cm⁻¹) are associated with carboxyl and methyl/methylene group vibrations, respectively. On the other hand, the strongest bands in the RS spectrum of HMB observed at 748/1442/1462 cm⁻¹ and 1408 cm⁻¹ are due to methyl/methylene deformations and carboxyl group vibrations, respectively. The strongest Raman band of creatine at 831 cm⁻¹ (ρ_w(R NH₂)) is accompanied by two weaker bands at 1054 and 1397 cm⁻¹ due to ν(CN) + ν(R NH₂) and ν_s(COOH) + ν(CN) + δ(CN) modes, respectively. In the case of L ‐carnitine, its RS spectrum is dominated by bands at 772 and 1461 cm⁻¹ assigned to ρ_r(CH₂) and δ(CH₃), respectively. The analysis of the SERS spectra shows that HMB interacts with the silver surface mainly through the  COO⁻, hydroxyl, and  CH₂ groups, whereas L ‐carnitine binds to the surface via  COO⁻ and  N⁺(CH₃)₃ which is rarely enhanced at pH = 8.3. On the other hand, it seems that creatine binds weakly to the silver surface mainly by  NH₂, and C O from the  COO⁻ group. Copyright © 2006 John Wiley & Sons, Ltd.     

Raman and infrared spectra,conformational stability,vibrational assignment,barriers to internal rotation and ab initio calculations of but-2-enoyl chloride

The Raman (3500–10 cm⁻¹) and infrared (3200–50 cm⁻¹) spectra were recorded for the fluid and solid phases of but-2-enoyl chloride (crotonyl chloride), trans-CH₃CHCHCClO, where the methyl group is trans to the CClO group, and a complete vibrational assignment is proposed. These data were interpreted on the basis that the s-trans (anti) form (two double bonds oriented trans to one another) is the most stable form in the fluid phases and the only conformer remaining in the solid state. The asymmetric torsional fundamental of the more stable s-trans and the higher energy s-cis (syn) form were observed at 97.5 and 86.9 cm⁻¹, respectively. From these data the asymmetric potential function governing the internal rotation about the C C bond was determined. The potential coefficients are V₁ = −111 ± 2, V₂ = 1860 ± 48, V₃ = 6 ± 2, V₄, = −43 ± 24 and V₆ = −22 ± 6. The s-trans to s-cis and s-cis to s-trans barriers were determined to be 1890 and 1785 cm⁻¹, respectively, with an enthalpy difference between the conformers of 105 ± 52 cm⁻¹ [300 ± 149 cal mol⁻¹ (1 cal = 4.184 J)]. Similarly, the barrier governing internal rotation of the CH₃ group for the s-trans conformer was also determined to be 912 ± 30 (2.61 ± 0.09 kcal mol⁻¹) from the torsional fundamental observed in the far-infared spectrum of the gas. All these data were compared with the corresponding quantities obtained from ab initio Hartree–Fock gradient calculations employing the RHF/3–21G*, RHF/6–31G* and/or MP2/6–31G* basis sets. These results were compared with the corresponding quantities for some similar molecules.     

FT‐Raman spectroscopic spectra on 3‐phenylpropylamine inclusion compounds

Some new Hofmann‐3‐phenylpropylamine‐type clathrates with chemical formulae of M(3‐phenylpropylamine)₂ Ni(CN)₄. 2G (MNi or Co, G = 1,2‐dichlorobenzene or 1,3‐dichlorobenzene) have been prepared and their Fourier transform infrared(FT‐IR; 4000–400 cm⁻¹), far‐infrared (600–100 cm⁻¹) and FT‐Raman (4000–60 cm⁻¹) spectra are reported. The ligand molecule, guest molecules, polymeric sheet and metal‐ligand bands of the clathrates are assigned in detail. The compounds are also characterized by thermal gravimetric analysis (TGA), differential thermal analysis (DTA), elemental analysis and magnetic susceptibility measurements. From the results, the monodentate 3‐phenylpropylamine ligand molecule bonds to the metal atom of |M‐Ni(CN)₄ | _∞ polymeric layers in the trans‐gauche‐gauche (TGG) form, and 1,2‐dichlorobenzene or 1,3‐dichlorobenzene molecules are guested by this structure revealing the inclusion ability of the host complexes. Copyright © 2010 John Wiley & Sons, Ltd.     

电化学法制备高密度导电聚吡咯的性能研究

系统地研究了溶剂、温度和聚合电流密度对电化学制备本征导电聚吡咯 (PPy)膜密度的影响,分别用四探针法和热失重(TG)法研究了不同密度的PPy膜的电导率和热稳定性.用循环伏安法(CV)和电化学阻抗谱(EIS)法比较了不同密度的PPy膜的电化学性能.研究表明,在室温下,在乙氰/水(AN/H₂O, 99/1)溶液比在水溶液中容易得到高密度的PPy膜.高聚合电流密度(如10mA/cm²)可以进一步提高PPy膜的密度,用X射线光电子能谱(XPS)对其结构进行了分析.在AN/H₂O(99/1)溶液中用小电流密度(0.1mA/cm²)聚合时,低温(-20℃)有利于提高PPy膜的密度;然而在高电流密度(10mA/cm²)时, 低温(-20℃)不利于提高PPy膜的密度.高密度的PPy膜(1.42g/cm³)用电流密度10mA/cm²在0℃的AN/H₂O(99/1)溶液中制得.该合成方法和常用的低温低电流密度方法制备高密度的PPy膜相比, 合成时间短,条件易实现,更利于实用化.更重要的是,高密度的PPy膜不仅具有高电导率(～220S/cm)和高热稳定性,还具有低的电化学活性.因此,高密度的PPy膜不仅是一种优异的电子导电的电极材料,而且是一种潜在的优异的防腐材料. 关键词： 聚吡咯膜 密度 电导率 热稳定性     

A new tyrosinase biosensor based on covalent immobilization of enzyme on N-(3-aminopropyl) pyrrole polymer film

A conducting polymer film of N-amino substituted pyrrole monomer has been prepared for covalent immobilization of enzyme for biosensing applications, illustrated by tyrosinase (PPO). The tyrosinase enzyme retains its bioactivity when being immobilized on N-substituted pyrrole polymer film by covalent bonding. The enzyme electrode was characterized by UV–Vis and infrared spectroscopy. Phenolic compounds were quantitatively estimated by the direct electrochemical reduction of enzymatically liberated quinone species at −0.2 V vs. Ag/AgCl. The results of amperometric response measurements conducted on enzyme electrode show sensitivity of 57.6, 71.4 and 45.8 mA M⁻¹ cm⁻² and a linear response range of 1.8–170.2, 1.3–110.1 and 2.1–168 μM for phenol, catechol and p-cresol, respectively. The biosensor exhibits a lowest detection limit of 0.9, 0.7 and 1.1 μM, for phenol, catechol and p-cresol, respectively and a period of stable sensitivity of 3 months at 4–5 °C.     

Preparation and electrochemistry of one-dimensional nanostructured MnO2/PPy composite for electrochemical capacitor

One-dimensional nanostructured manganese dioxide/polypyrrole (MnO₂/PPy) composite was prepared by in situ chemical oxidation polymerization of pyrrole in the host of inorganic matrix of MnO₂, using complex of methyl orange (MO)/FeCl₃ as a reactive self-degraded soft-template. The morphology and structure of the composite were characterized by infrared spectroscopy (IR) X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that the MnO₂/PPy composite consists of α-MnO₂ and PPy with nanotube-like structure. Electrochemical properties of the composite demonstrated the material showed good electrochemical reversibility after 500 charge-discharge cycles in the potential range of −0.4 to 0.6 V, the tube-like nanocomposite has the potential application in electrochemical capacitor.     

High‐resolution stimulated Raman spectroscopy and analysis of the ν1/ν5 (C–H) stretching dyad of C2H4

The high‐resolution stimulated Raman spectra of the ν₁/ν₅ C–H stretching bands of C₂H₄ have been recorded and analyzed by means of the tensorial formalism developed in Dijon for X₂Y₄ asymmetric‐top molecules. A total of 689 lines (428 for ν₅ and 261 for ν₁) were assigned and fitted as a dyad including Coriolis coupling constants. We obtained a global root mean square deviation of 4.39 × 10^{− 3} cm^{− 1} (4.61 × 10^{− 3} cm^{− 1} for ν₁, 4.25 × 10^{− 3} cm^{− 1} for ν₅). The nearby 2ν₂ band, extrapolated from ν₂, was included in the analysis. However, no interaction parameter involving it could be fitted. The analysis is quite satisfactory, although some parts of ν₅ are not very well reproduced, probably indicating some yet unidentified resonances. This region is indeed quite dense, with many interacting dark states that cannot be included at present. Copyright © 2012 John Wiley & Sons, Ltd.     

One‐Pot Synthesis of Algae‐Like MoS2/PPy Nanocomposite: A Synergistic Catalyst with Superior Peroxidase‐Like Catalytic Activity for H2O2 Detection

A facile one‐pot synthetic route is reported to prepare algae‐like molybdenum disulfide/polypyrrole (MoS₂/PPy) nanocomposite through a redox reaction between ammonium tetrathiomolybdate and pyrrole monomer under a hydrothermal condition without any other templates. The as‐prepared unique algae‐like MoS₂/PPy nanocomposites are composed of few layer MoS₂ nanosheets, which are covered with PPy. Structural and morphological characterizations of this unique nanocomposite are investigated by Fourier‐transform infrared spectra, Raman spectra, X‐ray diffraction pattern, X‐ray photoelectron spectra, energy‐dispersive X‐ray spectroscopy, and transmission electron microscopy. The as‐prepared MoS₂/PPy nanocomposites exhibit an excellent peroxidase‐like catalytic activity toward the oxidation of 3,3,5,5‐tetramethylbenzidine (TMB) in the presence of hydrogen peroxide (H₂O₂) in acetate buffer solution (pH 4.0), which provides a facile strategy for the colorimetric detection of H₂O₂ with a high sensitivity.     

Characterization of a LiCoO2 thin film cathode grown by pulsed laser deposition

A highly (003)-oriented pure LiCoO₂ thin film cathode, without Co₃O₄ impurities, was grown on a stainless steel substrate by pulsed laser deposition and characterized by electrochemical testing, scanning electron microscopy (SEM), ex situ X-ray diffraction (XRD), Raman and X-ray photoelectron spectroscopy (XPS). The initial reversible discharge capacity of the LiCoO₂ thin film cathode reached 52.5?μAh/cm²µm and capacity loss was about 0.18% per cycle at a current density of 12.74?μA/cm². The chemical diffusion coefficient of the Li⁺ ion was estimated to be about 4.7?×?10^?11?cm²/s from cyclic voltammetric (CV) scans. Ex situ XRD revealed that the spacing of crystalline planes expanded about 0.09?Å when charged to 4.2?V, corresponding to Li_0.5CoO₂, lower than the value for composite powder LiCoO₂ electrodes. XPS results showed that the number of low-coordinated oxygen ions increased relative to the removal of Li⁺ ions.     

High‐pressure studies of the micro‐Raman spectra of iron cyanide complexes: Prussian blue (Fe4[Fe(CN)6]3), potassium ferricyanide (K3[Fe(CN)6]), and sodium nitroprusside (Na2[Fe(CN)5(NO)]·2H2O)

The pressure dependences of the peaks observed in the micro‐Raman spectra of Prussian blue (Fe₄[Fe(CN)₆]₃), potassium ferricyanide (K₃[Fe(CN)₆]), and sodium nitroprusside (Na₂[Fe(CN)₅(NO)]·2H₂O) have been measured up to 5.0 GPa. The vibrational modes of Prussian blue appearing at 201 and 365 cm⁻¹ show negative dν/dP values and Grüneisen parameters and are assigned to the transverse bending modes of the Fe C N Fe linkage which can contribute to a negative thermal expansion behavior. A phase transition occurring between 2.0 and 2.8 GPa in potassium ferricyanide is shown by changes in the spectral region 150–700 cm⁻¹. In the spectra of the nitroprusside ion, there are strong interactions between the FeN stretching mode and the FeNO bending and the axial CN stretching modes. The pressure dependence of the NO stretching vibration is positive, 5.6 cm⁻¹ GPa⁻¹, in contrast to the negative behavior in the iron(II)‐meso‐tetraphenyl porphyrinate complex. Copyright © 2011 John Wiley & Sons, Ltd.