Design and synthesis of novel (Z)-5-((1,3-diphenyl-1H-pyrazol-4-yl)methylene)-3-((1-substituted phenyl-1H-1,2,3-triazol-4-yl)methyl)thiazolidine-2,4-diones: a potential cytotoxic scaffolds and their molecular modeling studies

In an effort to discover potential cytotoxic agents, a series of novel (Z)-5-((1,3-diphenyl-1H-pyrazol-4-yl)methylene)-3-((1-substituted phenyl-1H-1,2,3-triazol-4-yl)methyl)thiazolidine-2,4-dione derivatives (8a–n) were designed and synthesized in various steps with acceptable reaction procedures with quantitative yields and characterized by ¹H NMR, ¹³C NMR, IR, HRMS and ESI–MS spectra. These newly synthesized novel derivatives were screened for their in vitro cell viability/cytotoxic studies against human breast cancer cell line (MCF-7) with various concentrations of 0.625 µM, 1.25 µM, 2.5 µM, 5 µM and 10 µM, respectively. The biological interpretation assay outcome was demonstrated in terms of cell viability percentage reduction and IC₅₀ values against standard reference drug cisplatin. Based on these results, most of the derivatives exhibited promising cytotoxic activity. Among them, particularly compounds 8j (R₁?=?OMe and R₃?=?NO₂) and 8e (R₃?=?CF₃) demonstrate remarkable cytotoxic activity with IC₅₀ values 0.426 µM?±?0.455 and 0.608 µM?±?0.408, which are even better than the standard drug cisplatin 0.636 µM?±?0.458 and compounds 8m (R₂?=?OMe and R₃?=?OMe) and 8c (R₃?=?OMe) exhibited closely equivalent IC₅₀ values to the standard drug with IC₅₀ values 0.95 µM?±?0.32 and 0.976 µM?±?0.313 and rest of the compounds exhibits moderate cytotoxic activity. Moreover, molecular modeling studies and ADME calculations of the novel synthesized derivatives are in adequate consent with the pharmacological screening results.

     

Novel tacrine-based acetylcholinesterase inhibitors as potential agents for the treatment of Alzheimer’s disease: Quinolotacrine hybrids

A new series of quinolotacrine hybrids including cyclopenta- and cyclohexa-quinolotacrine derivatives were designed, synthesized, and assessed as anti-cholinesterase (ChE) agents. The designed derivatives indicated higher inhibitory effect on the acetylcholinesterase (AChE) with IC₅₀ values of 0.285–100 µM compared to butyrylcholinesterase (BChE) with IC₅₀ values of?>?100 µM. Of these compounds, cyclohexa-quinolotacrine hybrids displayed a little better anti-AChE activity than cyclopenta-quinolotacrine hybrids. Compound 8-amino-7-(3-hydroxyphenyl)-5,7,9,10,11,12-hexahydro-6H-pyrano[2,3-b:5,6-c'] diquinolin-6-one (6m) including 3-hydroxyphenyl and cyclohexane ring moieties exhibited the best AChE inhibitory activity with IC₅₀ value of 0.285 µM. The kinetic and molecular docking studies indicated that compound 6m occupied both the catalytic anionic site (CAS) and peripheral anionic site (PAS) of AChE as a mixed inhibitor. Using neuroprotective assay against H₂O₂-induced cell death in PC12 cells, the compound 6h illustrated significant protection among the assessed compounds. In silico ADME studies estimated good drug-likeness for the designed compounds. As a result, these quinolotacrine hybrids can be very encouraging AChE inhibitors to treat Alzheimer’s disease.

Graphic abstract

A novel series of quinolotacrine hybrids were designed, synthesized, and evaluated against AChE and BChE enzymes as potential agents for the treatment of AD. The hybrids showed good to significant inhibitory activity against AChE (0.285–100 μM) compared to butyrylcholinesterase (BChE) with IC₅₀ values of?>?100 μM. Among them, compound 8-amino-7-(3-hydroxyphenyl)-5,7,9,10,11,12-hexahydro-6H-pyrano[2,3-b:5,6-c′] diquinolin-6-one (6 m) bearing 3-hydroxyphenyl moiety and cyclohexane ring exhibited the highest anti-AChE activity with IC₅₀ value of 0.285 μM. The kinetic and molecular docking studies illustrated that compound 6 m is a mixed inhibitor and binds to both the catalytic anionic site (CAS) and peripheral anionic site (PAS) of AChE.

     

Design and synthesis of novel 2-(6-thioxo-1,3,5-thiadiazinan-3-yl)-N′-phenylacethydrazide derivatives as potential fungicides

A series of novel 2-(6-thioxo-1,3,5-thiadiazinan-3-yl)-N′-phenylacethydrazide derivatives were designed, synthesized and evaluated for their antifungal activities against Fusarium graminearum (Fg), Rhizoctonia solani (Rs), Botrytis cinerea (Bc) and Colletotrichum capsici (Cc). The bioassay results in vitro showed that most of the title compounds exhibited impressive antifungal activities against the above plant fungi. Particularly, the compounds 5c, 5f, 5g, 5i, 5m and 5p displayed desirable anti-Rs activities, with the corresponding EC₅₀ values of 0.37, 0.32, 0.49, 0.50, 0.46 and 0.45 µg/mL, respectively, which are superior to the positive control carbendazim (0.55 µg/mL). Further in vivo bioassay results showed that the anti-Rs activity of title compound 5f at 200 µg/mL reached 95.84% on detached rice leaves and 93.96% on rice plants. Featuring convenient synthesis, novel structures and desirable antifungal activity, these 2-(6-thioxo-1,3,5-thiadiazinan-3-yl)-N′-phenylacethydrazide derivatives could be further studied as the potential candidates of novel agricultural fungicides.

     

Synthesis and biological evaluation of novel SIPI-7623 derivatives as farnesoid X receptor (FXR) antagonists

Most of reported steroidal FXR antagonists are restricted due to low potency. We described the design and synthesis of novel nonsteroidal scaffold SIPI-7623 derivatives as FXR antagonists. The most potent compound A-11 (IC₅₀?=?7.8?±?1.1 μM) showed better activity compared to SIPI-7623 (IC₅₀?=?40.8?±?1.7 μM) and guggulsterone (IC₅₀?=?45.9?±?1.1 μM). Docking of A-11 in FXR’s ligand-binding domain was also studied.

     

Ultrasound effects on restricted silica gelation during silica extraction from Pyro-Metallurgical copper slag under acidifying conditions

Pyro-metallurgical copper slag (CS) waste was used as the source material for ultrasound (US) silica extraction under acidification processes with 26 kHz with HCl, HNO₃, and H₂SO₄ at different concentrations at 100, 300, and 600 W. During acidifying extraction processes, US irradiation inhibited silica gel formation under acidic conditions, especially at lower acid concentrations of less than 6 M, whereas a lack of US irradiation led to enhanced gelation. When US stopped, gelation occurred to a considerable degree, suggesting that the gel particle size distribution was aggregated in the 3–400 µm size range. However, with US, the size was mainly in the 1–10 µm range. Results of elemental analysis indicated that US treatment decreased the co-precipitation of other metal ions such as Fe, Cu, and Al sourced from CS for lower acidic medium, whereas the higher concentration medium accelerated silica gelation and the co-precipitation of other metals. With acids of HCl and HNO₃, and H₂SO₄, the gelations were less likely to occur at 6 M and 3 M during US irradiation, but acidic extraction without US was efficient for silica gelation and co-precipitation of other metals in the purified silica. The silica extraction yield with H₂SO₄ concentration of 3 M was 80% with 0.04% of Fe, whereas the silica product from HCl 6 M had a 90% extraction yield with only 0.08% of Fe impurity. In contrast, even though the non-US system of HCl 6 M had a higher yield at 96%, the final product had 0.5% Fe impurity, which was much higher than the US system. Consequently, the US extraction process was quite noticeable for silica recovery from CS waste.     

Novel heterocyclic 1,3,4-oxadiazole derivatives of fluoroquinolones as a potent antibacterial agent: Synthesis and computational molecular modeling

Design and synthesis of novel series of 1,3,4-oxadiazoles containing FQs derivatives and screened their antibacterial, antimycobacterial properties. The synthesized compounds were characterized by different spectral techniques like IR, ¹H NMR, ¹³C NMR, mass and elemental analysis. The results of the antimicrobial activity and compounds 6d, 6b, 6e, 6f and 6a demonstrated potent antibacterial activities with zone of inhibition of 42, 36, 37, 34 and 30 mm against S. aureus, E. faecalis, S. pneumoniae, E. coli and K. pneumoniae, respectively. 1,3,4-Oxadiazole derivatives 6a, 6b, 6 g were showed excellent antimycobacterial activity against M. smegmatis H₃₇Rv with MICs 22.35, 16.20, 20.28 µg/mL, respectively. FQs 6d and 6b exhibited highest hydrogen bonding interactions with Asp83 (3.11 A?), Ser80 (2.15 A?) Asp27 (σ-σ), Arg87 (Π-Π), Arg87 (Π-Π), Ser80 (σ-σ), Ala84 (σ-σ) and binding energies ΔG?=????6.41, ??6.97 kcal/mol with active site of topoisomerase-IV from S. pneumoniae [4KPE]. We performed a computational investigation of compounds 6a–j for their absorption, distribution, metabolism and excretion (ADME) properties by using the Molinspiration, Molsoft toolkits. The ligands 6f, 6d and 6b reveal the highest pharmacokinetic properties and possess maximum drug-likeness model score 1.59, 1.46 and 1.23, respectively.

Graphic abstract

     

Electron paramagnetic resonance of sonicated powder suspensions in organic solvents

The chemical effects of the acoustic cavitation generated by ultrasound translates into the production of highly reactive radicals. Acoustic cavitation is widely explored in aqueous solutions but it remains poorly studied in organic liquids and in particular in liquid/solid media. However, several heterogeneous catalysis reactions take place in organic solvents.Thus, we sonicated trimethylene glycol and propylene glycol in the presence of silica particles (SiO₂) of different sizes (5–15 nm, 0.2–0.3 µm, 12–26 µm) and amounts (0.5 wt% and 3 wt%) at an ultrasound frequency of 20 kHz to quantify the radicals generated. The spin trap 5,5-dimethyl-1-pyrrolin–N-oxide (DMPO) was used to trap the generated radicals for study by electron paramagnetic resonance (EPR) spectroscopy. We identified the trapped radical as the hydroxyalkyl radical adduct of DMPO, and we quantified it using stable radical 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO) as a quantitation standard. The concentration of DMPO spin adducts in solutions containing silica size 12–26 µm was higher than the solution without particles. The presence of these particles increased the concentration of the acoustically generated radicals by a factor of 1.5 (29 µM for 0.5 wt% of SiO₂ size 12–26 µm vs 19 µM for 0 wt%, after 60 min of sonication). Ultrasound produced fewest radicals in solutions with the smallest particles; the concentration of radical adducts was highest for SiO₂ particle size 12–26 µm at 0.5 wt% loading, reaching 29 µM after 60 min sonication. Ultrasound power of 50.6 W produced more radicals than 24.7 W (23 µM and 18 µM, respectively, at 30 min sonication). Increased temperature during sonication generated more radical adducts in the medium (26 µM at 75 °C and 18 µM at 61 °C after 30 min sonication). Acoustic cavitation, in the presence of silica, increased the production of radical species in the studied organic medium.     

Impact of bubble coalescence in the determination of bubble sizes using a pulsed US technique: Part 2 – Effect of the nature of saturating gas

Knowledge on cavitation bubble size distribution, ambient radius of bubbles is of interest for many applications that include therapeutic and diagnostic medicine. It however becomes a hard quest when increasing the ultrasonic frequency, when direct observation of bubble dynamics is no longer possible. An indirect method based on the estimation of the bubble dissolution time under pulsed ultrasound (362 kHz) is used here under optimized conditions to derive ambient radii of cavitation bubbles in water saturated with He, Ar, Xe, O₂, N₂ and air: 3.0 µm for Ar, 1.2 µm for He, 3.1 µm for Xe, 2.8 µm for O₂, around 1 µm for N₂ and air. If the pulse on-time is increased, bubble coalescence occurs, the extent of which is rather limited for Ar but extremely high for He or N₂.     

Synthesis,Characterization and Applications of Schiff Base Chemosensor for Determination of Cr(III) Ions

The development of a highly sensitive, selective, and efficient sensor for the determination and detection of Cr(III) ions remains a great challenge. Recently, some fluorescent chemosensors have been developed for the recognition of Cr(III) ions. But, the main drawbacks of the reported fluorescent chemosensors are the lack of selectivity and interference of anions and other trivalent cations. Herein, we designed and synthesized a novel thiazole-based fluorescent and colorimetric Schiff base chemosensor SB2 for the detection of Cr(III) ion by chemodosimetric approach. Using different analytical techniques including UV–vis, ¹³C-NMR, ¹H-NMR, and FT-IR analysis the chemosensor SB2 was structurally characterized. The fully characterized chemosensor SB2 was used for the spectrofluorimetric and colorimetric detection of Cr(III) ions. Interestingly, chemosensor SB2 upon interaction with various metal cations including Ni²⁺, Na⁺, Cd²⁺, Ag⁺, Mn²⁺, K⁺, Zn²⁺, Cu²⁺, Hg²⁺, Co²⁺, Pb²⁺, Mg²⁺, Sn²⁺, Al³⁺ and Cr³⁺ displays highly selective and sensitive fluorescent (turn-on) and colorimetric (yellow to colorless) response toward Cr(III) ions. The fluorescence and UV–vis techniques confirmed the selective hydrolysis of azomethine group (-C?=?N-) of Schiff base chemosensor SB2 by Cr(III) ions. As a result, the fluorescence enhancement was observed that is corresponding to 2-hydroxy-1-nepthaldehyde (fluorophore). The chemosensor SB2 exhibits high interference performance towards Cr(III) ions over other metal cations in a wide pH range. Mover, the quite low detection limit was calculated to be 0.027 µg ml-1 (0.5 µM) (3σ/slop), lower than the maximum tolerable limits of Cr(III ions (10 µM) in drinking water permitted by the United States Environmental Protection Agency (EPA). These results show that chemosensor SB2 has great potential to detect selectively Cr(III) ions in the agricultural, environmental and biological analysis system.

Graphical Abstract

     

Electrical and optical characterization of SiOxNy and SiO2 dielectric layers and rear surface passivation by using SiO2/SiOxNy stack layers with screen printed local Al-BSF for c-Si solar cells

In c-Si solar cells, surface recombination velocity increases as the wafer thickness decreases due to an increase in surface to volume ratio. For high efficiency, in addition to low surface recombination velocity at the rear side, a high internal reflection from the rear surface is also required. The SiO_xN_y film with low absorbance can act as rear surface reflector. In this study, industrially feasible SiO₂/SiO_xN_y stack for rear surface passivation and screen printed local aluminium back surface field were used in the cell structure. A 3 nm thick oxide layer has resulted in low fixed oxide charge density of 1.58 × 10¹¹ cm⁻² without parasitic shunting. The oxide layer capped with SiO_xN_y layer led to surface recombination velocity of 155 cm/s after firing. Using single layer (SiO₂) rear passivation, an efficiency of 18.13% has been obtained with V_oc of 625 mV, J_sc of 36.4 mA/cm² and fill factor of 78.7%. By using double layer (SiO₂/SiO_xN_y stack) passivation at the rear side, an efficiency of 18.59% has been achieved with V_oc of 632 mV, J_sc of 37.6 mA/cm², and fill factor of 78.3%. An improved cell performance was obtained with SiO₂/SiO_xN_y rear stack passivation and local BSF.     

Mixture Design Optimization of an Analytical Procedure for Iron Extraction and Determination From Cassava Leaves by Slurry Sampling Flame Atomic Absorption Spectrometry

ABSTRACT

This paper applies statistical simplex-centroid design to mixture modeling for optimization of the liquid phase composition of cassava slurry leaves in the development of an analytical procedure for iron determination using flame atomic absorption spectrometry (FAAS). This procedure is based on a slurry formation from powdered cassava leaves and a liquid mixture composed of HNO₃, HCl, and H₂O₂ after an ultrasonication process. A quadratic model fitted to the analytical response shows the existence of an experimental region, characterized by low proportions of H₂O₂, for which higher responses are obtained. The proposed procedure allows the determination of iron in the cassava leaves with a detection limit of 1.1 µg g^?1. The precision expressed as relative standard deviation (%RSD, n = 10) was 1.5% for iron concentrations of 25 µg g^?1. The developed procedure was validated by the comparison of results obtained from the application of the digestion procedure and the analysis of certified reference materials: Apple leaves (NIST 1515). Results found were in agreement with the certified values. The proposed method was applied for the determination of iron in four samples of cassava leaves acquired in markets of Feira de Santana City, Brazil. The concentration of iron found in the cassava leaves varied from 250.8 ± 0.7 to 283.4 ± 0.7 µg g^?1.     

Highly Selective and Sensitive Benzimidazole Based Bifunctional Sensor for Targeting Inedible Azo Dyes in Red Chilli,Red Food Color,Turmeric Powder,and Cu(Ii) in Coconut Water

In this study, a simple Benzimidazole based bifunctional chemosensor 4-(2-(3,4-dimethoxyphenyl)-1H-benzo[d]imidazol-6-yl) benzene-1,2-diamine, L was synthesized and characterized. The sensor proved to be selective and sensitive towards detecting banned azo dyes Sudan Dye I, II, and Metanil Yellow via fluorescence turn-off response. The proposed mechanism of fluorescence quenching was the inner filter effect. LODs for Sudan I, II, and Metanil Yellow were found to be 0.009 µM, 0.012 µM, and 0.0073 µM, respectively. The developed chemosensor also showed a colorimetric response towards Cu (II) ions via an apparent color change from yellow to pink. LOD for Cu (II) ions was found to be 1.2 µM. The synthesized benzimidazole based bifunctional chemosensor was adequately tested to determine Sudan I in Red chili powder and red Food color samples, Metanil yellow in turmeric powder, and Cu(II) packaged coconut water.

     

A feasible sonochemical approach to synthesize CuO@CeO2 nanomaterial and their enhanced non-enzymatic sensor performance towards neurotransmitter

A nanostructured and high conductive cupric oxide (CuO NPs) with hierarchical CeO₂ sheets-like structure was synthesized by a facile sonochemical approach. Furthermore, CuO/CeO₂ nanostructure is synthesized by high-intensity ultrasonic probe (Ti-horn, 50 kHz and 100 W) at ambient air. Moreover, the synthesized CuO/CeO₂ material was characterized by various analytical techniques including FESEM, EDX, XRD and electrochemical methods. Then, the synthesized CuO/CeO₂ composite was applied for the electrocatalytic detection of dopamine using CV and DPV techniques. In addition, the CuO/CeO₂ modified electrode has good electrocatalytic performance with high linear range from 0.025 to 98.5 µM towards the determination of dopamine drug and high sensitivity of the CuO/CeO₂ modified drug sensor was calculated as 16.34 nM and 4.823 μA·µM⁻¹·cm⁻², respectively. Moreover, a repeatability, reproducibility and stability of the CuO@CeO₂ mixture modified electrode were analyzed towards the determination of dopamine biomolecule. Interestingly, the real time application of CuO@CeO₂ modified electrode was established in different serum and drug samples.     

Characterization of thin film lithium electrode materials

Thin rf-sputtered films of Li₄Fe_0.5±xTi_4.5±yO_11.75±z, Li₄Co_0.5±xTi_4.5±yO_11.5±z, Li₄Ti_5±xO_12±y, LiCo_1±xO_2±y and C were investigated by X-ray diffraction, thickness and weight determination, ICP/AAS, EDX and coulometric titration experiments employing the following liquid electrolytes (PC:EC:DMC=1:1:3, 1 M LiPF₆), (PC:DEC=1:4, 1 M LiPF₆), (EC:DMC=1:1, 1 M LiPF₆), (PC:DME=1:1, 1 M LiClO₄) and (γ-buthyrolactone, 1M LiClO₄). For comparison, cold isostatically pressed monolithic pellets of Li₄Fe_0.5Ti_4.5O_11.75, Li₄Co_0.5Ti_4.5O_11.5 and Li₄Ti₅O₁₂ were examined. The slope of the coulometric titration curves depends strongly on the employed liquid electrolyte. In the case of thin films, the stoichiometric width of the liquid electrolyte salt may have an additional impact on the results.     

Eco-friendly methods of synthesis and preliminary biological evaluation of sulfonamide derivatives of cyclic arylguanidines

The chemotype of arylsulfonamide derivatives of cyclic arylguanidines is a source of molecules with valuable biological activities, including antimicrobial and antitumor properties. The methods of the synthesis presented in the literature are characterized with low selectivity and high environmental nuisance. In this publication, we present a developed alternative and earlier undescribed pathway C, for the synthesis of arylsulfonamide derivatives of cyclic arylguanidines (N-(1H-arylimidazol-2-yl)arylsulfonamides and N-(1,4-dihydroquinazolin-2-yl)arylsulfonamides), including reaction between 2-(methylsulfanyl)-benzimidazole or 2-(methylsulfanyl)-3,4-dihydroquinazoline with arylsulfonamides. We also optimized previously reported methods; A (reaction of 2-aminobenzimidazole or 2-amino-3,4-dihydroquinazoline with arylsulfonyl chlorides) and B (reaction of dimethyl-(arylsulfonyl)carbonodithioimidate with aryldiamines). The conducted research allowed achieving two independent ecological and quick methods of obtaining the desired products. We used ecological methods of ultrasound-assisted or microwave synthesis, solvent-free reactions and a “green” reaction environment. In both pathways, it has proven advantageous to use H₂O as the solvent and K₂CO₃ (1 or 3 equivalent) as the basic agent. In the sonochemical variant, the efficiency reached B: 37–89 %, C: 90 % in 60 min (P = 80 W and f = 40 kHz), while in the microwave synthesis it was B: 38–74 %, C: 63–85 % in 0.5–4 min (P = 50 W). Path A led to a complementary substitution product (i.e. 1-(arylsulfonyl)-1H-benzimidazol-2-amine or 1-(arylsulfonyl)-1,4-dihydroquinazolin-2-amine). We obtained a small group of compounds that were tested for cytotoxicity. The 10f (N-(1,4-dihydroquinazolin-2-yl)naphthalene-1-sulfonamide) showed cytotoxic activity towards human astrocytoma cell line 1321 N1. The calculated IC₅₀ value was 8.22 µM at 24 h timepoint (doxorubicin suppressed 1321 N1 cell viability with IC₅₀ of 1.1 µM). The viability of the cells exposed to 10f for 24 h dropped to 48.0 % compared to vehicle control, while the cells treated with doxorubicin experienced decline to 47.5 %. We assessed its potential usefulness in pharmacotherapy in the ADMET study, confirming its ability to cross the blood–brain barrier (Pe = 5.0 ± 1.5 × 10^-6 cm/s) and the safety of its potential use in terms of DDI and hepatotoxicity.     

Dual Fluorometric Detection of Fe3+ and Hg2+ Ions in an Aqueous Medium Using Carbon Quantum Dots as a “Turn-off” Fluorescence Sensor

The present study aimed to develop a carbon dots-based fluorescence (FL) sensor that can detect more than one pollutant simultaneously in the same aqueous solution. The carbon dots-based FL sensor has been prepared by employing a facile hydrothermal method using citric acid and ethylenediamine as precursors. The as-synthesized CDs displayed excellent hydrophilicity, good photostability and blue fluorescence under UV light. They have been used as an efficient “turn-off” FL sensor for dual sensing of Fe³⁺ and Hg²⁺ ions in an aqueous medium with high sensitivity and selectivity through a static quenching mechanism. The lowest limit of detection (LOD) for Fe³⁺ and Hg²⁺ ions was found to be 0.406 µM and 0.934 µM, respectively over the concentration range of 0-50 µM. Therefore, the present work provides an effective strategy to monitor the concentration of Fe³⁺ and Hg²⁺ ions simultaneously in an aqueous medium using environment-friendly CDs.

Graphical Abstract

     

Nonlinear optical activity of imino-dyes with furan,thiophene or thiazole moieties as π-conjugated bridge: a computational investigation

ABSTRACT

The electronic, linear and nonlinear optical properties of some heterocycle-containing imino-dyes, namely, the synthesised dyes 1–3 and the designed dye 4, were evaluated using suitable long-range corrected DFT functionals. HOMO–LUMO gaps, dipole moments, polarisabilities, and first hyperpolarisabilities were calculated using CAM-B3LYP, ωB97XD and LC-ωPBE methods combined with the 6-311++G(d,p) basis set using CAM-B3LYP/6-31G(d,p) optimised geometries. The calculated molecular hyperpolarisabilities, µβ, increase in the order 1?<?2?<?3 as expected experimentally. The enhancement of µβ when passing from dye 1 to dye 2 is due to the replacement of furan by thiophene and the increase of µβ when passing from dye 2 to dye 3 is due to the change of the thiophene position from the acceptor side to the donor side. Interestingly, the replacement of thiophene (dye 2) by thiazole (dye 4) leads to a notable increase of the NLO response. The electronic transitions data of dyes 1–4 were calculated at the CIS/6-31G(d,p) level of theory and the predicted order 1?<?2<3?<?4 of µβ values is conveniently explained using the two-level model based on the calculation of the dipole moment absolute change, |Δµ_EG |, from the ground to the excited state. Consequently, dye 4 could be a promising candidate for organic NLO devices.     

Structural chemistry and zeolitic properties of mixed oxalates with two open-framework types based on eight coordinate metals

Two families of open-framework materials have been obtained from the assembly of MO₈ polyhedra and oxalate groups as building blocks. The compounds can be formulated as [MM′(C₂O₄)₄]²⁻(M″_y)²⁺ · (4 + x)H₂O (y is 2 for monovalent M″ metals and 1 for divalent M″ metals), in which the sum of the valences of the two metals M and M′ involved in the anionic framework is six. The water molecules and counter cations, located in the voids of the structure, lead to zeolitic or cation dynamic properties.     

Sonochemical synthesis of novel thermo-responsive polymer and tungsten dioxide composite for the temperature-controlled reversible “on-off” electrochemical detection of β-Blocker metoprolol

Thermo-responsive polymer nanocomposite based on poly (styrene-co-N-isopropylacrylamide) hybrid tungsten dioxide (WO₂@PS-co-PNIPAM) was synthesized by a facile ultrasonic irradiation (Frequency; 20 kHz, power; 180 W, calorimetrically determined power; 5.73 W in the bath, and Type; probe) method in the presence of water as inisolv. The as-synthesized WO₂@PS-co-PNIPAM modified glassy carbon electrode (WO₂@PS-co-PNIPAM/GCE) was acting as a reversibly switched detection for the electrooxidation of metoprolol (MTP), with the thermal stimuli response of the PNIPAM. In below lower critical solution temperature (LCST), the PS-co-PNIPAM expanded to embed the electroactive sites of WO₂, and the MTP could not proceed via the polymer to attain electronic transfer, indicating the “off” state. Rather, in above LCST, the PS-co-PNIPAM shrank to reveal electroactive sites and expand cyclic voltammetric background peak currents, the MTP was capable to undergo electro-oxidation reaction usually and produce the response current, indicating “on” state. Additionally, the proposed sensor had excellent sensitivity (2.21 µA µM⁻¹ cm⁻²), wide dynamic range (0.05–306 µM), and a low limit of detection of 0.03 µM for MTP. Intriguingly, the fabricated sensor demonstrates the good selectivity towards the detection of MTP among the possible interfering compounds. Eventually, the WO₂@PS-co-PNIPAM/GCE has been utilized in the analysis of MTP in human blood serum samples.     

A sonochemical synthesis of SrTiO3 supported N-doped graphene oxide as a highly efficient electrocatalyst for electrochemical reduction of a chemotherapeutic drug

A sonochemical based green synthesis method playa powerful role in nanomaterials and composite development. In this work, we developed a perovskite type of strontium titanate via sonochemical process. SrTiO₃ particles were incorporated with nitrogen doped graphene oxide through simple ultrasonic irradiation method. The SrTiO₃/NGO was characterized by various analytical methods. The nanocomposite of SrTiO₃/NGO was modified with laser-induced graphene electrode (LIGE). The SrTiO₃/NGO/LIGE was applied for electrochemical sensor towards chemotherapeutic drug detection (nilutamide). Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) techniques have been used to examine the electrochemical performance of nilutamide (anti-cancer drug). DPV was found to be more sensitive and found to exhibit a sensitivity 8.627 µA µM⁻¹ cm⁻² for SrTiO₃/NGO/LIGE with a wide linear range (0.02–892 µM) and low Limit of detection (LOD: 1.16 µM). SrTiO₃/NGO/LIGE has been examined for the detection of nilutamide in blood serum and urine samples and obtained a good recovery in the range of 97.2–99.72 %. The enhanced stability and selectivity and practical application results indicates the suitability of SrTiO₃/NGO/LIGE towards the detection of nilutamide drug in pharmaceutical industries.