纳米TiO2的微波水热法制备及其光催化性能研究

利用硫酸钛和尿素为主要原料,EDTA为控制剂,微波水热法制备得到TiO2纳米光催化剂颗粒,分析了TiO2纳米晶粒的形成机理。TEM、XRD、FT-IR、TG-DSC对所得的催化剂进行了结构表征。结果表明,TiO2纳米光催化剂颗粒具有粒径小、颗粒分散性好、纯度高等特性。进一步的研究表明,后续的热处理可以对TiO2纳米晶粒的晶相进行调节。光催化活性检测是以低浓度酸性大红3R水溶液为降解目标,结果表明,该TiO2催化剂表现出了较高的催化活性。     

TiO2纳米晶复合纳米棒染料敏化太阳能电池

通过二次水热法合成锐钛矿TiO₂纳米棒(ANR). 采用X射线衍射(XRD)、场发射扫描电镜(FE-SEM)和透射电镜(TEM)等手段对其进行表征. 通过调节ANR和锐钛矿纳米颗粒(ANP)的掺杂比例来增加TiO₂纳米晶膜的光捕获效率和电子传输速率, 并对比了单层结构(ANR+ANP)和双层结构(ANP/(ANR+ANP))的纳米晶膜光阳极的光电转化性能. 在AM 1.5、光强100 mW·cm^-2的模拟太阳光下测试, 染料N719敏化的双层结构太阳能电池光电转化效率达7.3%, 比相同条件下单层纯ANP光阳极器件的光电转化效率(6.1%)提高了20%.     

FTIR study on the formation of TiO2 nanostructures in supercritical CO2

TiO(2) nanospherical and fibered structures were obtained via a one-step sol-gel method in supercritical carbon dioxide (scCO(2)) involving polycondensation of the alkoxide monomers titanium isopropoxide (TIP) and titanium butoxide (TBO) with acetic acid (HAc). The resulting materials were characterized by means of electron microscopy (SEM and TEM), X-ray diffraction (XRD), thermal analysis (TGA), and attenuated total reflection Fourier transmission infrared (ATR-FTIR) analysis. Depending on the experimental conditions, TiO(2) anatase nanospheres with a diameter of 20 nm or TiO(2) anatase/rutile nanofibers with a diameter of 10-100 nm were obtained. Fiber formation was enhanced by a higher HAc/Ti ratio and the use of the titanium isopropoxide (TIP) monomer. The mechanism of the microstructure formation was studied using in situ FTIR analysis in scCO(2). The FTIR results indicated that the formation of nanofibers was favored by a titanium hexamer that leads to one-dimensional condensation, while nanospheres were favored by a hexamer that permits three-dimensional condensation.     

海绵状纳米结构TiO2膜的制备及其光催化活性

采用电化学阳极氧化法在钛表面构筑了海绵状纳米结构TiO2膜. 应用扫描电子显微镜(SEM)和X射线衍射(XRD)对膜层的形貌和晶型进行了分析和表征, 考察了阳极氧化时间对膜层厚度的影响, 并通过海绵状纳米结构TiO2膜对甲基橙的光催化降解研究了膜层厚度与光催化活性的关系. 结果表明, 海绵状纳米结构TiO2膜对甲基橙具有光催化降解作用, 而且随着膜层厚度的增加, 光催化降解速率显著增大, 厚度为2.2 μm的海绵状纳米结构TiO2膜对甲基橙的光催化降解速率是厚度为480 nm的6.4倍.     

氧化钛-氧化石墨插层结构及其光催化性能(英文)

采用氧化石墨(GO)和硫酸钛作为初始反应物,在低温下(80℃)制备了纳米级的氧化钛-氧化石墨插层(TiO2-GO)复合材料,研究了这一复合材料的紫外光催化性能.结果表明,在采用TiO2-GO插层复合材料对甲基橙溶液进行紫外光催化降解时,其降解效率η=1.17mg·min-1·g-1,明显优于德固赛P25氧化钛粉.通过对TiO2-GO插层复合材料进行X射线衍射(XRD)、傅里叶红外(FT-IR)光谱、X射线光电子能谱(XPS)和场发射扫描电子显微镜(FESEM)等测试,表征了产物的晶相结构、界面状况及其显微结构.结果表明:插层结构中的TiO2晶粒为锐钛矿和金红石的混合相,且锐钛矿相含量大于金红石相含量;氧化石墨层间的含氧基团如C襒O,基本被还原.对TiO2-GO插层复合材料的形成机理以及该材料具有优越光催化性能的原因进行了探讨.     

硅胶负载氯掺杂二氧化钛光催化剂的水热制备与光催化活性评价

利用水热法, 以硅胶为载体, 以Ti(SO4)2为钛源, NaCl为氯源制备了具有良好性能的硅胶负载氯掺杂二氧化钛(CTS)光催化剂, 考察了氯投加量、焙烧温度及钛硅比对光催化活性的影响. 结果表明, 氯投加量为15% (nCl/nTi)、钛硅物质的量比为3:1、焙烧温度为750 ℃时制备的CTS具有最佳的光催化活性, 其比表面积为60.8 m2·g-1. CTS中的硅胶除了作为载体, 还起到了促进锐钛矿二氧化钛的生成并抑制其向金红石相转变的作用; 氯掺杂二氧化钛(CT)经硅胶负载后, 其表面孔结构发生了变化, 并且热稳定性增加. 苯酚降解实验表明, 与CT相比, CTS以0.7740 g·g-1的二氧化钛含量具有更高的光催化活性.     

阳极氧化法制备二氧化钛纳米管阵列的研究

采用电化学阳极氧化法,将纯钛浸入HF酸水溶液,在钛基体表面原位构建高度有序的二氧化钛纳米管阵列,探讨阳极氧化电压、电解液浓度和电解液温度等对二氧化钛纳米管阵列尺寸和形貌的影响。通过SEM、XRD对二氧化钛纳米管阵列的结构特征进行表征,结果表明,不同的阳极氧化电压、电解液浓度和温度都将影响TiO2纳米管阵列的尺寸和形貌,在阳极氧化电压为20V,HF电解液浓度为0.5%t条件下,可制备出结构规整有序的TiO2纳米管阵列。     

溶胶-凝胶法合成钛酸锌陶瓷粉体

本文以钛酸四丁酯、乙酸锌、柠檬酸、乙二醇和乙醇为主要原料，用溶胶-凝胶（Sol-Gel）法，经两次热处理合成出均一的钛酸锌（ZnTiO₃）陶瓷粉体，并用TG-DTA、XRD和FE-SEM等对其组织结构和形貌进行了表征。结果表明，热处理方式对产物组成和晶型有较大影响。     

Microwave synthesis of porous ZnGaNO solid solution for improved visible light photocatalytic performance

Porous ZnGaNO solid solution has been synthesized through a facile microwave route. The product was characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM), high-resolution transmission electron microscopy (HRTEM) and UV–vis diffuse reflection spectroscopy, X-ray photoelectron spectroscopy (XPS), Energy dispersed spectrometer (EDS) and N₂-sorption. The growth process of porous ZnGaNO solid solution is investigated by XRD and SEM. The porous structure is supposed to be attributed to the release of the gaseous side products and the structural contraction through a pseudo-topological transformation. The activity of porous ZnGaNO photocatalyst for photodegradation of isopropyl alcohol (IPA) is much higher than that of ZnGaNO solid solution prepared by a solid state reaction. The as-prepared porous ZnGaNO photocatalyst exhibits an improved photocatalytic activity due to the strong gas adsorption by the porous structure and the enhancement of extended light absorption by the higher Zn content.     

TiO2纳米管阵列光电催化氧化处理氨氮废水

用电化学阳极氧化法制备了高度有序的钛基二氧化钛纳米管阵列薄膜。用场发射扫描电镜(FE-SEM)、X射线衍射(XRD)表征样品的形貌与晶型特征。以二氧化钛纳米管阵列为光阳极,石墨为对电极,测试了不同pH值和外加偏压条件下的光电流响应和光电催化氧化降解NH4Cl水溶液(以N计,100 mg·L-1)的效率。结果表明:所制备的TiO2纳米管阵列具有锐钛矿和金红石的混晶结构,且主要晶型为锐钛矿。光电流响应的强弱与光电催化氧化效率的高低相对应,降解氨氮废水的最佳条件为pH=11,偏压为1.0 V。     

电纺丝-气相沉积法制备碳包覆TiO_2纳米纤维及其光催化行为的研究

以聚乙烯吡咯烷酮(PVP)溶胶/钛酸正丁酯为前躯体,以静电纺丝法制备了PVP/Ti(OC4H9)4纤维。550℃下,空气氛中焙烧双组分纤维,得到直径60～300nm的TiO2纳米纤维。继而以气相沉积法制得碳包覆TiO2纳米纤维。用红外吸收光谱(FTIR)、X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)等对纳米纤维进行了表征。与TiO2纳米纤维、TiO2纳米粉体相比,气相沉积法制备的碳包覆TiO2纳米纤维在光分解亚甲基蓝上表现出更好的催化性能。     

Synthesis and Characterization of a Novel Graphene Oxide/titanium Dioxide Solvent-free Nanofluid

A novel graphene oxide/titanium dioxide(GO/TiO_2) solvent-free nanofluid was firstly synthesized by employing GO, which was in-situ deposited by TiO_2 as the core and(3-Glycidyloxypropyl) trime thoxysilane(KH560) and polyetheramine-M2070 as the shell. The morphology and structure of GO/TiO_2 nanofluid were verified by Transmission electron microscopy(TEM), X-ray diffraction(XRD) analysis, Fourier transform infrared spectroscopy(FTIR), X-ray photoelectron spectroscopy(XPS) and UV-vis absorption spectra. These studies confirmed that TiO_2 has been deposited onto GO with good dispersion, and the organic shell has been grafted onto the core successfully. Thermo gravimetric analysis(TGA) and viscosity analysis indicated that this nanoparticle hybrid material presented a liquid state without solvent at room temperature, and has great fluidity and thermal stability. The solubility investigation of GO/TiO_2 nanofluid revealed its excellent amphiphilicity and the potential as the functional nanocomposites.     

三维大孔TiO2光催化剂的制备及其催化性能

 以聚甲基丙烯酸甲酯微球为模板,以钛酸正丁酯为原料,采用溶胶-凝胶法制备了具有三维结构的大孔TiO2. 采用差示扫描量热、热重-微分热重、X射线衍射、红外光谱、扫描电子显微镜和氮气吸附等手段对样品进行了表征. 结果表明,高温热处理后得到的三维大孔TiO2光催化剂的孔径为200 nm左右,孔径分布均匀, TiO2纳米晶粒中锐钛矿相和金红石相的含量分别为82%和18%. 光催化氧化实验表明,此种三维结构的TiO2对甲基橙溶液具有较好的光催化氧化性能.     

Phase structure and luminescence properties of Eu3+-doped TiO2 nanocrystals synthesized by Ar/O2 radio frequency thermal plasma oxidation of liquid precursor mists

Eu3+-doped TiO2 luminescent nanocrystals have been synthesized in this work via Ar/O2 thermal plasma oxidizing mists of liquid precursors containing titanium tetra-n-butoxide and europium(III) nitrate, with varied O2 input in the plasma sheath (10-90 L/min) and Eu3+ addition in the precursor solution (Eu/(Ti + Eu) = 0-5 atom%). The resultant nanopowders are mixtures of the anatase (30-36 nm) and rutile (64-83 nm) polymorphs in the studied range, but the rutile fraction increases steadily at a higher Eu3+ addition, as revealed by X-ray diffraction (XRD) and Raman spectroscopy, because of the creation of oxygen vacancies in the TiO2 gas clusters by substitutional Eu3+ doping. The amount of Eu3+ that can be doped into a TiO2 lattice was limited up to 0.5 atom%, above which Eu2Ti2O7 pyrochlore was formed in the final products. High resolution transmission electron microscopy (HRTEM) observation indicates that the particles are dense and have sizes ranging from several nanometers up to 180 nm. Efficient nonradiative energy transfer from the TiO2 host to Eu3+ ions, which was seldom reported in the wet-chemically derived nanoparticles or thin films of the current system, was confirmed by combined studies of excitation, UV-vis (ultraviolet-visible), and PL (photoluminescence) spectroscopy. As a consequence of this, bright red emissions were observed from the plasma-generated nanopowders either by exciting the TiO2 host with UV light shorter than 405 nm or by directly exciting Eu3+ at a wavelength beyond the absorption edge (405 nm) of TiO2.     

不同形貌WO3的水热合成及其在水处理中的应用研究

三氧化钨(WO₃)以其较窄的带隙,成为继二氧化钛(TiO₂)之后颇具发展潜力的n型半导体光催化剂.本文采用水热合成法,通过调控反应参数,如原料组成、沉淀时间等,合成了不同形貌和晶型的WO₃;采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、傅里叶变换红外光谱(FT-IR)、氮气吸附-脱附(N₂ adsorption-desorption)等表征了所合成的WO₃产品,发现原料组成、沉淀时间等条件对WO₃的晶型和形貌都有影响;研究了所合成的WO₃产品去除水中亚甲基蓝染料污染物的性能,结果表明,所制备的WO₃对水中亚甲基蓝具有较好的去除效果,去除率可达97%.     

Conducting polyaniline-rutile TiO2 nanocomposites for the development of high-k dielectric materials

Inorganic dielectrics encapsulated in an organic matrix are showing excellent promise as novel dielectric materials. In this work, firstly highly organized crystalline nanoparticles of rutile TiO₂ were synthesized by acid hydrolysis of titanium isopropoxide at room temperature. Then we developed a novel dielectric material consisting of highly organized rutile TiO₂/polyaniline (PAni) nanocomposites by in-situ chemical oxidative polymerization. The structural, morphological, conducting, and dielectric properties of the rutile TiO₂/PAni nanoparticles have been evaluated by X-ray diffraction (XRD), scanning electron microscopy (SEM), high resolution-transmission emission microscopy (HR-TEM), four-point probe technique, CV (Capacitance versus Voltage), and Impedance analyzer. The nanocomposites show 70 times higher permittivity compared to rutile nanoparticles and much higher compared to anatase/PAni (ES) nanocomposites at 10 MHz. Large interfacial polarizations, nanostructure, and dopant levels are the key factors for the large dielectric constant of the nanocomposites. The rutile/PAni (ES) nanocomposites might see potential uses in super-capacitors, gate dielectric in transistors, and capacitive-type gas sensors.     

钒掺杂TiO2/AC负载催化剂的制备及光催化活性

以TiO2为主要成分的光催化剂的研究已日益受到人们的广泛关注[1-6]。但TiO2粉末的回收和流失问题难以解决,固定化TiO2负载催化剂的研制是解决这一问题的有效手段[2-6]。从实际应用的观点看,TiO2的光催化剂活性还有待进一步提高。研究发现,大多数过渡金属离子和少数非金属离子的     

TiCl4水解法制备的阻挡层对染料敏化太阳能电池光电性能的影响

通过不同浓度的TiCl₄溶液水解, 在光阳极导电玻璃(FTO)基底上制备了阻挡层薄膜, 以此来抑制FTO表面的光生电子与I₃^-之间的复合反应, 采用X射线光电子能谱(XPS)和X射线衍射分别测试了阻挡层薄膜的组成, 用场发射扫描电子显微镜(FE-SEM)和紫外-可见(UV-Vis)分光光度计测试了阻挡层的形貌和对光的透过率, 在AM1.5和暗环境下分别测试了染料敏化太阳能电池(DSSC)的光电性能. 实验结果表明: 用此方法可以获得由TiO₂粒子组成的阻挡层薄膜; 阻挡层薄膜的形貌随着TiCl₄溶液浓度的增加而改变, 它的厚度随着TiCl₄溶液浓度的增加而增加; 引入阻挡层后, FTO对光的透过率都会下降; 这一薄膜的引入可以提高电池的光电性能, 用0.04 mol·L^-1的TiCl₄溶液制备的阻挡层对暗电流的抑制作用最为明显, 电池在AM1.5的条件下测试, 转换效率最高达7.84%.     

六边形及圆形SmF3微米盘的水热合成与表征

以Sm(NO3)3·6H2O和不同的氟化物(NaBF4,NH4F)在120℃的低温水热条件下反应得到了六边形及圆形的SmF3微米盘.通过X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)和透射电子显微镜(TEM)对产物的晶相和形貌进行了表征.XRD结果显示所得的产物是结晶良好的六方晶系.SEM和TEM测试表明得到大量均匀的厚度约为200 nm的盘状结构.研究发现氟化物种类以及反应时间对形成不同形貌的盘有重要影响.讨论了可能的形成机理.进一步研究了SmF3:Tb3+和SmF3:Eu3+掺杂后的产物的荧光性质.     

Synthesis and gas sensitivities of SnO2 nanorods and hollow microspheres

SnO₂ urchin-like structures composed of nanorods with diameters of 10-15 nm and lengths of 50-70 nm have been hydrothermally synthesized via a H₂O₂-assisted route without any surfactant, using SnCl₂ as raw material. With the addition of methenamine (HMT), SnO₂ hollow microspheres with diameters of 2-3 μm and shell thickness of 60-140 nm were also prepared. The as-obtained products were examined using diverse techniques including X-ray powder diffraction (XRD), Raman spectroscopy, field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), selected-area electron diffraction (SAED), high-resolution TEM and photoluminescence spectra. The gas sensitivity experiments have demonstrated that the as-synthesized SnO₂ materials exhibit good sensitivity to alcohol vapors, which may offer potential applications in gas sensors.