Voltammetry of biologically active species and surfactants on new miniaturized and contractible (compressible) mercury electrodes

The adsorption of the polyether-antibiotic monensin from an aqueous solution on mercury was used to investigate the effect of the decreasing size of a stationary mercury drop electrode on the shape of the voltammetric desorption peak of the surfactant. The change of the i-E curve indicated an acceleration of the transport of the surfactant to the electrode as well as of time-dependent changes in the adsorption layer. A decrease of the radius of the hanging mercury drop electrode from 220 μm to 80 μm at a constant accumulation time of t_ac = 70 s resulted in an about 4-fold increase of the evaluated signal (i-E pre-wave) of monensin. A 7-fold increase of the voltammetric desorption peak of monensin at conc. 5 · 10^–7 mol/L was observed as result of a compressive accumulation of the surfactant due to a contraction of the mercury drop electrode. A scheme of an apparatus for voltammetric/polarographic measurements by means of the contractible (compressible) mercury drop electrode is described. The controlled contraction of the electrode surface is presented together with preliminary results covering a new way of accumulation of surfactants, new accumulation effects, effective in adsorptive voltammetry, and other electroanalytical techniques. Received: 26 March 1998 / Revised: 14 July 1998 / Accepted: 15 July 1998     

Adsorptive Stripping Voltammetric Determination of Ultra Trace of Zinc and Lead with Carbidopa as Complexing Agent in Food and Water Samples

In the present work, the cathodic stripping voltammetric methodology using a hanging mercury drop electrode was described for simultaneous determination of lead and zinc in different real samples. The method is based on adsorption of metal ions on mercury electrode using carbidopa as a suitable complexing agent. The potential was scanned to the negative direction and the differential pulse stripping voltammograms were recorded. Optimal conditions were found to be: accumulation time; 70 s, accumulation potential; 50 mV versus Ag/AgCl, scan rate; 40 mV s^?1, supporting electrolyte; 0.01 M ammonia buffer at pH 8.5, and concentration of carbidopa; 8.0 μM. The relationship between the peak current versus concentration was linear over the range of 0.1–210 and 0.2–170 nM for lead and zinc, respectively. The detection limits are 0.09 and 0.15 nM for lead and zinc ions respectively. The relative standard deviations at a concentration level of 70 nM of both metal ions are found 1.08 and 1.24% for lead and zinc ions respectively.     

Assessment of differential-pulse adsorption voltammetry for the simultaneous determination of nickel and cobalt in biological materials

An assessment of the voltammetric method based on chelate adsorption at the hanging mercury drop electrode is described for the simultaneous determination of nickel and cobalt in biological materials. The interfacial accumulation of the elements as metal dimethylglyoximates during the adsorption step, and the use of differential-pulse voltammetry during the reduction step, provide substantial gains in the sensitivity of their voltammetric responses. The decomposition of the sample material by direct dry ashing provides a blank-free approach for the accurate determination of the elements. Application of the method to the available certified biological reference materials for cobalt and nickel was successful. The limits of detection obtained under the conditions of this study were 0.01 μg g^?1 and 0.02 μg g^?1 for cobalt and nickel, respectively, in bovine liver.     

Trace Analysis of Iron in Environmental Water and Snow Samples from Poland

Abstract

A voltammetric method for the determination of iron at detection limit of 4 μg/l is described, using the catalytic current of the reduction of the Fe(III)-triethanolamine (TEA) complex in the presence of bromate ions. the determination was performed at a mercury hanging drop electrode without preconcentration, using the TEA alkaline solution as a supporting electrolyte and the differential pulse technique. A peak current for the Fe(III)-TEA catalytic reduction was observed at a potential of-1.0 V (Ag/AgCl saturated electrode). the influence of TEA, BrO³ and NaOH concentrations on the peak height was studied. It was found that a 100-fold excess of Mn, a 50-fold excess of Cr(VI) and Zn did not interfere in the determination. This method was applied to the determination of iron in water, snow and waste water samples.     

Determination of uranium by adsorptive stripping voltammetry

A voltammetric method for the determination of uranium in natural waters in the concentration range from 0.4 μg 1⁻¹ to 0.2 mg 1⁻¹ is described. The method is based on adsorptive accumulation of the uranium(VI)—pyrocatechol complex on the hanging mercury drop electrode followed by the reduction of the absorbed complex.     

Adsorptive stripping voltammetry of chlordiazepoxide at the hanging mercury drop electrode

Controlled adsorptive accumulation at the hanging mercury drop electrode enables 0.8–11 × 10^?5 M chlordiazepoxide to be quantified by differential-pulse stripping voltammetry with accumulation times of 1–3 min. With 3-min accumulation, the peak current is enhanced 12-fold for 1.0 × 10^?7 M chlordiazepoxide compared to the current from differential pulse polarography. The detection limit is 0.9 × 10^?9 M for 4-min accumulation. The procedure is applied to spiked human serum after preseparation of the drug on a Sep-Pak C₁₈ cartridge.     

Determination of the pesticide Chlorpyrifos by cathodic adsorptive stripping voltammetry

The adsorption behavior and differential pulse cathodic adsorptive stripping voltammetry of the pesticide Chlorpyrifos (CP) were investigated at the hanging mercury drop electrode (HMDE). The pesticide was accumulated at the HMDE and a well-defined stripping peak was obtained at –1.2 V vs Ag/AgCl electrode at pH 7.50. A voltammetric procedure was developed for the trace determination of Chlorpyrifos using differential pulse cathodic adsorptive stripping voltammetry (DP-CASV). The optimum working conditions for the determination of the compound were established. The peak current was linear over the concentration range 9.90 × 10^–8– 5.96 × 10^–7 mol/L of Chlorpyrifos. The influence of diverse ions and some other pesticides was investigated. The analysis of Chlorpyrifos in commercial formulations and treated waste water was carried out satisfactorily     

Voltammetric determination of mercury (II) in aqueous media using glassy carbon electrodes modified with novel calix[4]arene

A novel calix[4]arene derivative containing benzothiazole group was coated on glassy carbon electrode (GCE) and then applied to the recognition of mercury ion. Cyclic and square wave voltammetric results showed that the modified electrode selectively recognizes Hg²⁺ ion in aqueous media. A new anodic stripping peak at −0.3 V (vs. Ag/Ag⁺) can be obtained by scanning the potential from −0.6 to 0.6 V, and the peak currents are proportional to the Hg²⁺ concentration. The modified electrode in a 0.1 M H₂SO₄+0.01 M NaCl solution shows linear voltammetric response in the range of 25-300 μg l⁻¹ and detection limit of 5 μg l⁻¹ (ca. 2.5×10⁻⁸ M). This modified GCE does not present any significant interference from alkali, alkaline and transition metal ions except for Pb²⁺, Ag⁺ and Cu²⁺ ions. Only 500, 50 and 100-fold molar excess of Pb²⁺, Ag⁺ and Cu²⁺ ions, respectively, can lead to voltammetric response comparable with that of Hg²⁺. The proposed method was successfully applied to determine mercury in natural water.     

Contribution to the adsorption voltammetric determination of manganese

The adsorption voltammetric determination of Mn(II) with Bromopyrogallol Red (BPR) and Mordant Red 19 (MDR) has been investigated using a hanging drop mercury electrode. In NH₃/NH₄Cl solution, ligands and Mn(II) complexes give well separated voltammetric peaks after enrichment onto the electrode. The conditions for determining manganese by adsorption voltammetry with these reagents have been investigated in detail, as has the influence of foreign ions on the determination. The detection limits are 4·10^?10 mol/L Mn for BPR and 8·10^?10 mol/L Mn for MDR, respectively.     

Square-wave adsorptive stripping voltammetric determination of antihypertensive agent telmisartan in tablets and its application to human plasma

The adsorptive stripping voltammetry of telmisartan was investigated with a hanging mercury drop electrode. This compound produced a catalytic hydrogen wave at ?1.5 V in Britton Robinson buffer of pH 10.38, and the peak current increased with adsorptive accumulation at the electrode. Adsorptive stripping voltammetry with the catalytic hydrogen wave could provide a sensitive novel method for the determination of telmisartan. Various chemical and instrumental parameters affecting the monitored electroanalytical response were investigated and optimized for telmisartan determination. Under these optimized conditions the square-wave adsorptive stripping voltammetric (SW-AdSV) peak current showed a linear dependence on drug concentration over the range 0.05–3.00 μg/mL (1 × 10^?7?6 × 10^?6 M) (r = 0.999) with accumulation for 120 s at ?1.0 V vs. Ag/AgCl. The proposed electrochemical procedure was successfully applied for the determination of telmisartan in pharmaceutical tablets and human plasma. The results of the developed SW-AdSV method were comparable with those obtained by reported analytical procedures.     

Speciation of trace metals in natural waters: the influence of an adsorbed layer of natural organic matter (NOM) on voltammetric behaviour of copper

The influence of an adsorbed layer of the natural organic matter (NOM) on voltammetric behaviour of copper on a mercury drop electrode in natural water samples was studied. The adsorption of NOM strongly affects the differential pulse anodic stripping voltammogram (DPASV) of copper, leading to its distortion. Phase sensitive ac voltammetry confirmed that desorption of adsorbed NOM occurs in general at accumulation potentials more negative than −1.4 V. Accordingly, an application of negative potential (−1.6 V) for a very short time at the end of the accumulation time (1% of total accumulation time) to remove the adsorbed NOM was introduced in the measuring procedure. Using this protocol, a well-resolved peak without interferences was obtained. It was shown that stripping chronopotentiogram of copper (SCP) in the depletive mode is influenced by the adsorbed layer in the same manner as DPASV. The influence of the adsorbed NOM on pseudopolarographic measurements of copper and on determination of copper complexing capacity (CuCC) was demonstrated. A shift of the peak potential and the change of the half-peak width on the accumulation potential (for pseudopolarography) and on copper concentration in solution (for CuCC) were observed. By applying a desorption step these effects vanished, yielding different final results.     

Square wave voltammetric determination of diafenthiuron and its application to water,soil and insecticide formulation

A square wave cathodic stripping voltammetric (SWCSV) method has been developed for the determination of insecticide diafenthiuron. The procedure is based on controlled accumulation of the insecticide on a static hanging mercury drop electrode (SHMDE) at 0.00?mV (vs. Ag/AgCl) in Britton-Robinson buffer solution (pH 7.0). The insoluble mercury compound was reduced at ?510?mV during the cathodic potential scan. The peak currents were linearly related to insecticide concentration between 30.4 and 3200?µg?L^?1 . The detection and quantification limit were 9.1?µg?L^?1 and 30.4?µg?L^?1, respectively. The proposed analytical procedure was applied to natural water and soil samples. The method was extended to direct determination of diafenthiuron in insecticide formulation Polo® 50 WP and average content of 50.3?±?1.7 (m/m) at 90% confidence level, in close agreement with the 50.0% quoted by the manufacturer. HPLC comparison method indicated that accuracy was in agreement with that obtained by the proposed method.     

Voltammetric Behavior of Semicarbazide at Graphene Modified Electrode and Application to Detection

Herein voltammetric behaviors of semicarbazide (SEM) are investigated by employing a graphene modified working electrode, which displays attractive electroanalytical properties. In the acetate buffer solution of pH 4.00, there is a well‐defined oxidative peak of SEM, attributing to the irreversible and adsorption‐controlled electrode reaction with 2 electrons participation. The values of apparent heterogeneous electron transfer rate constant k′_s with the redox are 0.0061 s^?1 and 0.0009 s^?1, respectively, for two scan rate section. After the experimental parameters, which influence the voltammetric responses of SEM, including supporting electrolyte, pH, accumulation time and accumulation potential, etc., are optimized, it is found that the anodic peak current of SEM is proportional to its concentration in the range of 4 ‐ 40 μmol/L with a detection limit of 1 μmol/L (S/N = 3). Then, an electrochemical method for detecting SEM quantitatively is developed successfully. The concentrations of SEM in fortified tap water samples are tested with satisfactory recovery, indicating that the novel method is strongly promising in the environmental monitoring application.     

Electrode Modified with Langmuir–Blodgett (LB) Film of Calixarenes for Preconcentration and Stripping Analysis of Hg(II)

A new type of current sensor, Langmuir–Blodgett (LB) film of calixarene on the surface of glassy carbon electrode (GCE) was prepared for determination of mercury by anodic stripping voltammetry (ASV). An anodic stripping peak was obtained at 0.15 V (vs. SCE) by scanning the potential from ?0.6 to +0.6 V. Compared with a bare GCE, the LB film coated electrode greatly improves the sensitivity of measuring mercury ion. The fabricated electrode in a 0.1 M H₂SO₄+0.01 M HCl solution shows a linear voltammetric response in the range of 0.07–40 μg L^?1 and detection limit of 0.04 μg L^?1 (ca. 2×10^?10 M). The high sensitivity, selectivity, and stability of this LB film modified electrode demonstrates its practical application for a simple, rapid and economical determination of Hg²⁺ in a water sample.     

Cyclic voltammetry of nucleic acids and determination of submicrogram quantities of deoxyribonucleic acids by adsorptive stripping voltammetry

In cyclic voltammetry (at a mercury drop electrode) guanine residues in the polynucleotide chain give a characteristic anodic peak at potentials close to ?0.3 V (vs. saturated calomel electrode). At low concentrations of polynucleotide, this peak can be enhanced substantially if the potential scan is preceded by adsorptive preconcentration of the polynucleotide at the hanging mercury drop electrode. With accumulation times shorter than 10 min at pH 6.8, the limit of detection of a single-stranded polynucleotide is < 0.1 μg ml^?1. The peak of double-helical deoxyribonucleic acid (DNA) is considerably lower than that of single-stranded DNA under the same conditions, which can be exploited to determine low concentrations of single-stranded DNA in the presence of double-stranded DNA.     

Increased sensitivity of anodic stripping voltammetry at the hanging mercury drop electrode by ultracathodic deposition

An improved approach to the anodic stripping voltammetric (ASV) determination of heavy metals, using the hanging mercury drop electrode (HMDE), is reported. It was discovered that using very cathodic accumulation potentials, at which the solvent reduction occurs (overpotential deposition), the voltammetric signals of zinc(II), cadmium(II), lead(II) and copper(II) increase. When compared with the classical methodology a 5 to 10-fold signal increase is obtained. This effect is likely due to both mercury drop oscillation at such cathodic potentials and added local convection at the mercury drop surface caused by the evolution of hydrogen bubbles.     

Graphite multi-micro-disc based mercury film electrode: Comparison of experimental and theoretical anodic stripping results

an ensemble of properly distanced micro mercury film electrodes (MMFE) was used in cyclic and anodic stripping voltammetry. the experimental results were compared with the anodic stripping theory, and the agreement was found to be satisfactory. The MMFE peaks (calculated per unit area) were higher, thinner and shifted towards more negative potentials compared with the large area mercury film electrode (LAMFE) peaks.The initial graphite electrode consisted of 65 independent micro-discs forming a circle, and was prepared from carbon fibres 4.66 μm in radius. The graphite multi-micro-disc electrode was quantitatively checked in a Fe(CN)₆^3? solution under both chronoamperometric and voltammetric conditions. The deposition and oxidation of mercury is discussed also.     

Simultaneous Determination of Iron,Copper, and Cadmium by Adsorptive Stripping Voltammetry in the Presence of Thymolphthalexone

A novel, sensitive and selective adsorptive stripping procedure for simultaneous determination of iron, copper and cadmium is presented. The method is based on the adsorptive accumulation of thymolphthalexone (TPN) complexes of these elements onto a hanging mercury drop electrode, followed by reduction of adsorbed species by voltammetric scan using differential pulse modulation. The influences of control variables on the sensitivity of the proposed method for the simultaneous determination of iron, copper and cadmium were studied using the Derringer desirability function. The optimum analytical conditions were found to be TPN concentration of 2.0 μM, pH of 9.5, and accumulation potential at ?0.4 V vs. Ag/AgCl with an accumulation time of 60 s. The peak currents are proportional to the concentration of iron, copper and cadmium over the 1–80, 0.5–100 and 1–100 ng mL^?1 ranges with detection limits of 0.5, 0.4 and 0.9 ng mL^?1_, respectively. The R.S.D. at a concentration level of 20 ng mL^?1 of iron, copper and cadmium were 2.5%, 0.9% and 1.5% (n=6), respectively. The procedure was applied to the simultaneous determination of iron, copper and cadmium in the tap water and some synthetic samples with satisfactory results.     

Determination of the pesticide Chlorpyrifos by cathodic adsorptive stripping voltammetry

The adsorption behavior and differential pulse cathodic adsorptive stripping voltammetry of the pesticide Chlorpyrifos (CP) were investigated at the hanging mercury drop electrode (HMDE). The pesticide was accumulated at the HMDE and a well-defined stripping peak was obtained at –1.2 V vs Ag/AgCl electrode at pH 7.50. A voltammetric procedure was developed for the trace determination of Chlorpyrifos using differential pulse cathodic adsorptive stripping voltammetry (DP-CASV). The optimum working conditions for the determination of the compound were established. The peak current was linear over the concentration range 9.90 × 10^–8– 5.96 × 10^–7 mol/L of Chlorpyrifos. The influence of diverse ions and some other pesticides was investigated. The analysis of Chlorpyrifos in commercial formulations and treated waste water was carried out satisfactorily Received: 10 July 1997 / Revised: 1 April 1998 / Accepted: 6 April 1998     

Determination of nanomolar levels of guanine by differential-pulse adsorptive cathodic stripping voltammetry of its copper(II) complex

Guanine is determined at the 5.0×10^–10 –2.0×10^–7 mol/l level by differential-pulse adsorptive stripping voltammetry at a hanging mercury drop electrode using the reduction peak of its copper (II) complex at –0.21 V vs. Ag-AgCl electrode. The optimum analytical conditions were found to be Britton-Robinson buffer solution (pH 4.8), an accumulation potential of 0.0 V and an accumulation time of 3 min. Under these conditions, the detection limit is 5.0×10^–10 mol/l and the relative standard deviation 2.6% for 1.0×10^–7 mol/l guanine. The method is compared with the previous voltammetric methods. The presence of some purine derivatives does not interfere.