Evaporation behavior of water from aqueous dispersions of multihollow particles prepared by the stepwise alkali/acid method

In order to clarify the formation mechanism of multihollow structures inside styrene–methacrylic acid copolymer particles prepared by the stepwise alkali/acid method, which we proposed in 1990, the evaporation behavior of water from aqueous dispersions of the original carboxylated particles and those after the alkali treatment and the stepwise alkali/acid treatments was examined. It is concluded that the particle after the alkali treatment had a number of small water pools inside. Received: 22 February 2001 Accepted: 20 June 2001     

Copolycondensations of bisphenols with aggregates of isophthalic acid and terephthalic acid activated by tosyl chloride/dimethylformamide/pyridine in different manners

A mixture of isophthalic acid (IPA) and terephthalic acid (TPA) was activated by a tosyl chloride/dimethylformamide/pyridine (Py) condensing agent in two steps via the treatment of a mixture of the initially activated IPA/TPA with additional TPA followed by the activation of TPA with the agent. The resulting mixture showed a solubility in Py different from that obtained by the activation of them all at once; the difference might be due to different structures of the aggregates of the activated IPA and TPA at the same composition of the diacids. The structures of the aggregates were evaluated on the basis of melting points and the IR spectra of a mixture of dimethyl esters of IPA and TPA produced by the quenching of the reaction mixtures with methanol. The mixture obtained by two‐step activation showed lower melting points and spectral changes due to enhanced associations of the esters with respect to the mixture prepared by the activation of them all at once. The aggregates were also examined in terms of the distributions of IPA and TPA in thermotropic copolyesters prepared from methylhydroquinone and chlorohydroquinone by their transition temperatures and ¹³C NMR. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3884–3892, 2001     

Preparation of styrene/acrylic acid copolymer microspheres: polymerization mechanism and carboxyl group distribution

 Poly(styrene-co-acrylic acid) (St/AA) copolymer microspheres were prepared by batch emulsifier-free emulsion copolymerization of St with AA. The monomer conversion, the morphology and the composition of the particles along the polymerization process were monitored by a gravimetric method, transmission electron microscopy observation and Fourier transform IR analysis, respectively. A shift of the polymerization locus from inside the particles to “outside” the particles in the postnucleation stage was proposed. The results of the study of the distribution of carboxyl groups by a combination of elemental and X-ray photoelectron spectroscopy analyses implied a core/shell structure for the St/AA copolymer microspheres. By chemical metal deposition, nickel particles were formed and deposited on the surface of St/AA microspheres, forming polymer/metal composite particles. Received: 16 February 2001 Accepted: 8 August 2001     

Reverse atom transfer radical polymerization of methyl methacrylate with a new catalytic system,FeCl3/isophthalic acid

A new catalytic system, FeCl₃/isophthalic acid, was successfully used in the reverse atom transfer radical polymerization (RATRP) of methyl methacrylate (MMA) in the presence of a conventional radical initiator, 2,2′‐azo‐bis‐isobutyrontrile. Well‐defined poly(methyl methacrylate) (PMMA) was synthesized in an N,N‐dimethylformamide solvent at 90–120 °C. The polymerization was controlled up to a molecular weight of 50,000, and the polydispersity index was 1.4. Chain extension was performed to confirm the living nature of the polymer. The kinetics of the RATRP of MMA with FeCl₃/isophthalic acid as the catalyst system was investigated. The apparent activation energy was 10.47 kcal/mol. The presence of the end chloride atom on the resulting PMMA was demonstrated by ¹H NMR spectroscopy. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 765–774, 2001     

A quartz crystal microbalance sensor for the detection of formic acid vapors

A new quartz crystal microbalance sensor is developed to determine formic acid at low concentrations. Four previously selected polymers with acid–base characteristics were tested as possible coatings. Polyoxyethylene bis [amine] presented the best results. The sensor is rapid, sensitive [0.67 Hz/(mg/m³)], and reversible at low concentrations. The detection limit for formic acid (7.2 mg/m³) is comparable with the short term exposure limit and the threshold limit values. It presents a fast mechanical response to pressure changes, so that it can be quickly used in different environments and situations. The sensor also shows a good stability in a temperature range typical of work atmospheres (16–36 °C). It has a wide linear range (7.2–911.2 mg/m³) and a long useful time. It is also applicable to other low molecular mass carboxylic acids such as acetic acid. Received: 26 September 2000 / Revised: 8 February 2001 / Accepted: 12 February 2001     

Synthesis and chemical structural analysis of nitroxyl‐radical‐incorporated poly(acrylic acid/lactide/ϵ‐caprolactone) copolymers

The goal of this research is to synthesize biodegradable polymers that would have nitroxyl radical biological functions. Linear aliphatic polyesters were chosen as the starting materials. The hydroxyl‐terminated polylactide/?‐caprolactones (PBLC‐OHs) were first synthesized by melt ring‐opening copolymerization in the presence of benzyl alcohol and stannous octoate. PBLC‐OHs were used as the precursor for the synthesis of double bond‐functionalized polylactide/?‐caprolactones (PBLC‐Mas) by reacting the hydroxyl end groups of PBLC‐OH with maleic anhydride in melt at 130 °C. Acrylic acid/lactide/?‐caprolactone graft copolymers (PBLCAs) were then successfully carried out by the radical copolymerization of acrylic acid and PBLC‐Ma initiated by azobisisobutyronitrile. Finally, nitroxyl radicals [4‐amino‐2,2,6,6‐tetramethylpiperidine‐1‐oxy (TAM)] were incorporated into the carboxylic acid sites of the acrylic acid/lactide/?‐caprolactone copolymer (TAM‐PBLCA) by reacting TAM with PBLCA in the presence of N,N′‐carbonyl diimidazole. A high content of TAM was incorporated into the PBLCA copolymer. The polymers synthesized were characterized by ¹H and ¹³C NMR, Fourier transform infrared spectroscopy, and electron paramagnetic resonance spectra. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4214–4226, 2001     

Graft copolymerization induced by thermal reactions of the binary alkali salts of poly(carboxylic acid)–brominated carboxylic acid in bulk

Thermal reactions of the binary alkali salts of poly(carboxylic acid)–brominated carboxylic acid such as sodium or potassium poly(4-vinylbenzoate)-2-bromopropanoate [Na or K (PVBA-2-BPA)] in bulk were investigated. A methanol solution of binary acids was prepared by fixing the molar ratio of the repeating unit of polymeric acid to the fraction of brominated carboxylic acid. The binary salts were prepared by the neutralization of the binary acid solution. The product of the thermal reaction followed by esterification was identified as a graft copolymer containing PVBA in the main chain and polylactic acid in the side chain. The reaction of 1/15 K (PVBA-2-BPA) at 120 °C for 2 h yielded the highest percentage of grafting (300%). The grafting proceeded gradually for the initial 2 h and then somewhat. Reactivity of the K salt was higher than that of the corresponding Na salt. The thermal reaction of 1/10 K [polymethacrylate-2-BPA (PMA-2-BPA)] at 120 °C for 2 h also yielded a graft copolymer, and the percentage of grafting was 300%. However, reaction temperatures higher than 120 °C caused homopolycondensation of K 2-BPA prior to grafting, and homopolycondensation occurred prior to grafting in the reaction with Na (PMA-2-BPA). © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1877–1885, 2001     

Radiation synthesis and uranyl‐ion adsorption of poly(2‐hydroxyethyl methacrylate/maleic acid) hydrogels

A new kind of copolymeric hydrogel adsorbent containing hydrophilic groups that both provides swelling in water and chelates with uranyl ions was synthesized, and its adsorptive ability for recovering uranium from aqueous media was investigated. The uranyl adsorption capacities of poly(2‐hydroxyethyl methacrylate/maleic acid) hydrogels were determined with a polarographic technique to be 3.2–4.8 (mg UO/g dry gel) from a 15‐ppm uranyl nitrate solution at pH, 6 depending on the molar content of maleic acid in the hydrogel. Adsorption studies showed that other stimuli, the temperature, and the ionic strength of the solution also have important roles in the uranyl‐ion adsorption capacity of these hydrogels. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 277–283, 2001     

Aggregation of laponite in the presence of magnesium ions and polyacrylic acid

The average mass and size characteristics of ageing laponite/MgCl₂ and laponite/MgCl₂/polyacrylic acid were determined in aqueous dispersions at pH 10 using a Coulter counter and laser diffractometry methods. Comparison between mass and size characteristics showed the two systems to temporarily acquire a structure where particles are more densely packed. The relatively higher packing observed for laponite/polymer was attributed to conformational changes of the polymer adsorbed on neighbouring surfaces. Analysis of the reduced mass and size distribution functions confirmed the self-similarity of the distributions. The reduced mass frequency continuously decreased, while the reduced size frequency showed a linear decrease combined with bell-shaped populations. The volume packing observed for the laponite/polymer was attributed to a typical class of aggregates of large size, which was present at the maximal concentration in the bell-shaped distribution. Received: 19 February 2001 Accepted: 6 April 2001     

Proton‐conducting poly(vinylpyrrolidon)–polyphosphoric acid blends

Anhydrous, proton‐conducting polymer electrolytes of poly(vinylpyrrolidon) (PVP) with polyphosphoric acid (PPA) were prepared. PVP‐x‐PPA blends were obtained for 0.5 ≤ x ≤ 3, where x was the number of moles of PO per polymer repeat unit. Fourier transform infrared studies indicated protonation of the carbonyl group in the five‐member ring. Thermogravimetric analysis showed that these materials were stable up to about 180 °C. Differential scanning calorimetry data demonstrated that the addition of the acid plasticized the material, shifting the glass‐transition temperature from 180 °C for the pure polymer to ?23 °C for x = 3. The temperature dependence of the mechanical properties was investigated with shear experiments. The direct‐current conductivity increased with x and reached about 10^?5 S/cm at ambient temperature. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1987–1994, 2001     

Controlled stereochemistry of polyamides derived from cis/trans‐1,4‐cyclohexanedicarboxylic acid

A series of copolyamides 12.y was synthesized either with y = 6, or 1,4‐cyclohexanedicarboxylic acid (1,4‐CHDA) residue, or a mixture of both. The influence of the synthetic route of 1,4‐CHDA containing polyamides on the obtained cis–trans ratio of the incorporated 1,4‐CHDA was investigated. The use of acid chlorides provided a synthetic route with full control of the cis–trans ratio of the 1,4‐CHDA residue during synthesis, whereas synthesis at elevated pressure and temperature caused isomerization. The content and cis–trans ratio of 1,4‐CHDA in the copolyamides were determined by solution ¹³C NMR spectroscopy. Increasing the degree of partial substitution of the adipic acid by 1,4‐CHDA resulted in an increase in T_m, even for low molar precentages of 1,4‐CHDA. This phenomenon points to isomorphous crystallization of both the 12.6 and 12.CHDA repeating units. The mps of the synthesized polyamides were independent of the initial cis–trans ratio of 1,4‐CHDA, provided that the samples were annealed at 300 °C before DSC analysis. The polyamides exhibited a different melting pattern depending on the 1,4‐CHDA content. At a low a 1,4‐CHDA content a net exothermic recrystallization occurred during melting, whereas at higher contents of 1,4‐CHDA this recrystallization occurs to a lesser extent, and two separate melting areas are observed. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 833–840, 2001     

Controlled polymerization of acrylic acid under 60Co irradiation in the presence of dibenzyl trithiocarbonate

The polymerization of acrylic acid (AA) was performed under ⁶⁰Co irradiation in the presence of dibenzyl trithiocarbonate at room temperature, and well‐defined poly(acrylic acid) (PAA) with a low polydispersity index was successfully prepared. The gel permeation chromatographic and ¹H NMR data showed that this polymerization displays living free‐radical polymerization characteristics: a narrow molecular weight distribution (M_w/M_n = 1.07–1.22), controlled molecular weight, and constant chain‐radical concentration during the polymerization. Using PAA? S? C(?S)? S? PAA as an initiator, the extension reaction of PAA with fresh AA was carried out under ⁶⁰Co irradiation, and the results indicated that this extension polymerization displayed controlled polymerization behavior. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3934–3939, 2001     

Combined effects of Ca2+ and humic acid on colloid transport through porous media

We report the separate and combined effects of humic acid and Ca²⁺ ions on the transport of colloidal particles through a sand-packed column. Polystyrene latex particles with a sulfate functional group were used as model colloids. The concentrations of both the inlet solution and the effluent solutions were measured during each experimental run. Breakthrough curves were obtained by taking the ratios of each effluent sample concentration to the inlet solution concentration. In the absence of humic acid, the results indicate that increasing the concentration of Ca²⁺ increases particle attachment to the sand, thus causing decreased transport rates of latex particles through the porous bed matrix. Once 4 mg/l humic acid was added to the system, changes were observed in the effect that Ca²⁺ has on latex particle breakthrough. In a system containing calcium, increasing the humic acid concentration was shown to reduce particle attachment and increase transport rates. In the absence of calcium, the ratios for the outlet-to-inlet concentrations were similar for each concentration of humic acid. The electrophoretic mobility was also measured in order to determine the role of electrostatic repulsion in the latex particle transport. The electrophoretic mobility of the latex particles was found to be dependent on humic acid concentration in the absence of Ca²⁺ but not in its presence. Received: 2 February 2001 Accepted: 6 2001     

Synthesis and proton conductivities of phosphonic acid containing poly‐(arylene ether)s

A novel phosphonic acid containing bisphenol was successfully synthesized from phenolphthalein and m‐aminophenylphosphonic acid. A series of homo‐ and copoly‐(arylene ether)s containing phosphonic acid groups were prepared by solution nucleophilic polycondensation. These phosphonic acid containing polymers can readily be dissolved in common organic solvents, such as dimethyl sulfoxide, N‐methyl‐2‐pyrrolidinone, and N‐cyclohexylpyrrolidinone, and can be cast into tough and smooth films. The presence of phosphonic acid pendants in the poly‐(arylene ether)s was confirmed by NMR, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, and conductivity measurements. This is the first report on the attachment of phenylphosphonic acid groups as side chains to aromatic polyethers. These poly‐(arylene ether)s had very high glass‐transition temperatures ranging from 254 to >315 °C and high molecular weights. The conductivities of the synthesized polymers were analyzed by the Cole–Cole method, and they ranged from 10^?5 to 10^?6 Scm^?1. The synthesized polymers also exhibited good solution processability. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3218–3226, 2001     

Anodic oxidation of formic acid on PdAuIr /C-Sb_2O_5·SnO_2 electrocatalysts prepared by borohydride reduction

PdAuIr/C-Sb2O5·SnO2electrocatalysts with Pd∶Au∶Ir molar ratios of 90∶5∶5,70∶20∶10 and 50∶45∶5 were prepared by borohydride reduction method.These electrocatalysts were characterized by EDX,X-ray diffraction,transmission electron microscopy and the catalytic activity toward formic acid electro-oxidation in acid medium investigated by cyclic voltammetry(CV),chroamperometry(CA)and tests on direct formic acid fuel cell(DFAFC)at 100℃.X-ray diffractograms of PdAuIr/C-Sb2O5·SnO2electrocatalysts showed the presence of Pd fcc phase,Pd-Au fcc alloys,carbon and ATO phases,while Ir phases were not observed.TEM micrographs and histograms indicated that the nanoparticles were not well dispersed on the support and some agglomerates.The cyclic voltammetry and chroamperometry studies showed that PdAuIr/C-Sb2O5·SnO2(50∶45∶5)had superior performance toward formic acid electro-oxidation at 25℃compared to PdAuIr/C-Sb2O5·SnO2(70∶20∶10),PdAuIr/C-Sb2O5·SnO2(90∶5∶5)and Pd/C-Sb2O5·SnO2electrocatalysts.The experiments in a single DFAFC also showed that all PdAuIr/C-Sb2O5·SnO2electrocatalysts exhibited higher performance for formic acid oxidation in comparison with Pd/C-Sb2O5·SnO2electrocatalysts,however PdAuIr/C-Sb2O5·SnO2(90∶5∶5)had superior performance.These results indicated that the addition of Au and Ir to Pd favor the electro-oxidation of formic acid,which could be attributed to the bifunctional mechanism(the presence of ATO,Au and Ir oxides species)associated to the electronic effect(Pd-Au fcc alloys).     

Using pseudo amino acid composition to predict protein structural class: approached by incorporating 400 dipeptide components

The proteins structure can be mainly classified into four classes: all-alpha, all-beta, alpha/beta, and alpha + beta protein according to their chain fold topologies. For the purpose of predicting the protein structural class, a new predicting algorithm, in which the increment of diversity combines with Quadratic Discriminant analysis, is presented to study and predict protein structural class. On the basis of the concept of the pseudo amino acid composition (Chou, Proteins: Struct Funct Genet 2001, 43, 246; Erratum: Proteins Struct Funct Genet 2001, 44, 60), 400 dipeptide components and 20 amino acid composition are, respectively, selected as parameters of diversity source. Total of 204 nonhomologous proteins constructed by Chou (Chou, Biochem Biophys Res Commun 1999, 264, 216) are used for training and testing the predictive model. The predicted results by using the pseudo amino acids approach as proposed in this paper can remarkably improve the success rates, and hence the current method may play a complementary role to other existing methods for predicting protein structural classification.     

Synthesis and specific biodegradation of novel polyesteramides containing amino acid residues

Novel polyesteramides were synthesized from p‐nitrophenyl esters of sebacic or adipic acids and diamines containing α‐amino acid ester groups. The optimal polymerization condition was 60 °C in N,N‐dimethylformamide. The structures of these polymers were confirmed by IR and NMR. The number‐average molecular weights of these polyesteramides ranged from 2280 to 23,600 (except for the polymers containing glycine residues), depending on the nature of the amino acid used. The biodegradability of the polyesteramides was investigated by in vitro hydrolysis with proteases and a lipase as catalysts in borate buffer solutions. The results indicated that the polymers containing L ‐phenylalanine were hydrolyzed most effectively by α‐chymotrypsin, subtilisin Carlsberg, and subtilisin BPN′. The polyesteramides containing other amino acid residues also underwent hydrolysis to different extents, reflecting the substrate specificity of the proteases. Lipase had almost no effect on the hydrolytic degradation of these polyesteramides. The polymers containing glycine residues were hardly decomposed by any of the enzymes used. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1318–1328, 2001     

Synthesis of aromatic polyethersulfone‐based graft copolyacrylates via ATRP catalyzed by FeCl2/isophthalic acid

The atom transfer radical polymerization (ATRP) catalyzed by the FeCl₂/isophthalic acid system was used for the preparation of novel aromatic polyethersulfone (PSF)‐based graft copolymers in N,N‐dimethylformamide (DMF), such as aromatic PSF‐graft‐poly(methyl methacrylate), aromatic PSF‐graft‐polymethylacrylate, and aromatic PSF‐graft‐poly(butyl acrylate). The route consisted of two steps. The first step included the chloromethylation of aromatic PSF, and the second step involved the ATRP of acrylate monomers using chloromethylated aromatic PSF as the macroinitiator and FeCl₂/isophthalic acid as the catalyst in DMF. Characterization data by gel permeation chromatography, DSC, IR, ¹H NMR, and thermogravimetric analysis confirmed that the graft copolymerization was successful. Only one glass‐transition temperature (T_g) was observed for aromatic PSF‐graft‐poly(methyl methacrylate), and two T_g's were detected for aromatic PSF‐graft‐methyl acrylate and aromatic PSF‐graft‐poly(butyl acrylate). © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2943–2950, 2001     

Production of multi-hollow polymer particles by the stepwise acid/alkali method

 Recently, we reported that multi-hollow polymer particles can be prepared from carboxylated polymer particles by the stepwise alkali/acid method. In this article, an attempt was made to prepare similar particles from acid-swellable polymer particles by the stepwise treatment with acid and alkali, which was named the stepwise acid/alkali method. The acid-swellable particles were produced by emulsion terpolymerization of styrene, butyl acrylate, and dimethyl 2-amino ethyl methacrylate. The effects of initial pH value, temperature, and time in the acid and alkali treatment processes on the multi-hollow structure were examined. Received: 18 December 1996 Accepted: 11 March 1997     

Acrylamide/maleic acid hydrogels

Acrylamide/maleic acid hydrogels in the form of rods were prepared by γ-irradiating ternary mixtures of acrylamide–maleic acid–water with 2.00–5.71 kGy γ-rays. The influence of dose and relative content of maleic acid on the spectroscopic, thermal and mechanical properties, swelling properties, diffusional behavior of water and diffusion coefficients of hydrogel systems are examined. Acrylamide/maleic acid hydrogels were swelled in the range of 1000–2800%, While polyacrylamide hydrogels were swelled in the range of 650–700%. Water diffusion to hydrogels in non-Fickian type diffusion. The diffusion coefficients varied from 4.5 × 10^?2 to 12.2 × 10^?7 cm² sec^?1.