Towards high-performance cathode materials for lithium-ion batteries: Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-coated LiNi<Subscript>0.8</Subscript>Co<Subscript>0.15</Subscript>Zn<Subscript>0.05</Subscript>O<Subscript>2</Subscript>

Zn-doped LiNi_0.8Co_0.2O₂ exhibits impressive electrochemical performance but suffers limited cycling stability due to the relative large size of irregular and bare particle which is prepared by conventional solid-state method usually requiring high calcination temperature and prolonged calcination time. Here, submicron LiNi_0.8Co_0.15Zn_0.05O₂ as cathode material for lithium-ion batteries is synthesized by a facile sol-gel method, which followed by coating Al₂O₃ layer of about 15 nm to enhance its electrochemistry performance. The as-prepared Al₂O₃-coated LiNi_0.8Co_0.15Zn_0.05O₂ cathode delivers a highly reversible capacity of 182 mA h g^?1 and 94% capacity retention after 100 cycles at a current rate of 0.5 C, which is much superior to that of bare LiNi_0.8Co_0.15Zn_0.05O₂ cathode. The enhanced electrochemistry performance can be attributed to the Al₂O₃-coated protective layer, which prevents the direct contact between the LiNi_0.8Co_0.15Zn_0.05O₂ and electrolyte. The escalating trend of Li-ion diffusion coefficient estimated form electrochemical impedance spectroscopic (EIS) also indicate the enhanced structural stability of Al₂O₃-coated LiNi_0.8Co_0.15Zn_0.05O₂, which rationally illuminates the protection mechanism of the Al₂O₃-coated layer.     

Synthesis and electrochemical properties of Ca-doped LiNi<Subscript>0.8</Subscript>Co<Subscript>0.2</Subscript>O<Subscript>2</Subscript> cathode material for lithium ion battery

LiNi_0.8Co_0.2O₂ and Ca-doped LiNi_0.8Co_0.2O₂ cathode materials have been synthesized via a rheological phase reaction method. X-ray diffraction studies show that the Ca-doped material, and also the discharged electrode, maintains a hexagonal structure even when cycled in the range of 3.0–4.35 V (vs Li⁺/Li) after 100 cycles. Electrochemical tests show that Ca doping significantly improves the reversible capacity and cyclability. The improvement is attributed to the formation of defects caused by the partial occupancy of Ca²⁺ ions in lithium lattice sites, which reduce the resistance and thus improve the electrochemical properties.     

Layered LiNi<Subscript>0.80</Subscript>Co<Subscript>0.15</Subscript>Al<Subscript>0.05</Subscript>O<Subscript>2</Subscript> as cathode material for hybrid Li<Superscript>+</Superscript>/Na<Superscript>+</Superscript> batteries

LiNi_0.80Co_0.15Al_0.05O₂ (NCA) is explored to be applied in a hybrid Li⁺/Na⁺ battery for the first time. The cell is constructed with NCA as the positive electrode, sodium metal as the negative electrode, and 1 M NaClO₄ solution as the electrolyte. It is found that during electrochemical cycling both Na⁺ and Li⁺ ions are reversibly intercalated into/de-intercalated from NCA crystal lattice. The detailed electrochemical process is systematically investigated by inductively coupled plasma-optical emission spectrometry, ex situ X-ray diffraction, scanning electron microscopy, cyclic voltammetry, galvanostatic cycling, and electrochemical impedance spectroscopy. The NCA cathode can deliver initially a high capacity up to 174 mAh g^?1 and 95% coulombic efficiency under 0.1 C (1 C?=?120 mA g^?1) current rate between 1.5–4.1 V. It also shows excellent rate capability that reaches 92 mAh g^?1 at 10 C. Furthermore, this hybrid battery displays superior long-term cycle life with a capacity retention of 81% after 300 cycles in the voltage range from 2.0 to 4.0 V, offering a promising application in energy storage.     

The effects of sintering temperature and time on the structure and electrochemical performance of LiNi<Subscript>0.8</Subscript>Co<Subscript>0.2</Subscript>O<Subscript>2</Subscript> cathode materials derived from sol-gel method

LiNi _0.8Co _0.2O ₂ cathode materials were synthesized by the sol-gel method using citric acid as a chelating agent. The effects of sintering temperature and time on the structure and electrochemical performance of the materials were investigated. The materials were characterized by X-ray diffraction, together with refinement analysis by the Rietveld method. The results showed that sintering temperature and time had significant influence on the structure of the materials. The lattice parameters ( a, c, c/ a and volume) and the amount of Ni in the Li 3a site showed a peak shape change with sintering temperature and time. The sample sintering at 998 K for 24 h showed the best ordering layered structure with the maximum c/ a ratio and the least amount of Ni on the Li 3a site. The charge-discharge experiments also indicated that the sample had the best electrochemical properties, with an initial capacity of 181 mA h/g and a capacity retention of 82.9% after 50 cycles at a 0.1 C rate between 3.0 V and 4.2 V. In addition, the compositional homogeneity of these cathode materials derived using the sol-gel method was demonstrated by scanning electron microscopy/energy dispersive analysis.     

Effect of the preparation method of the cathode material LiNi<Subscript>0.33</Subscript>Mn<Subscript>0.33</Subscript>Co<Subscript>0.33</Subscript>O<Subscript>2</Subscript> on the electrochemical characteristics of a lithium ion cell

Complex metal oxides with the composition LiNi_0.33Mn_0.33Co_0.33O₂ prepared by various methods: sol–gel method, solid-phase method, and thermal destruction of metal-containing compounds in oil were studied. The results of elemental analysis, TGA/DSC, powder X-ray diffraction, SEM, TEM, as well as the results of electrochemical testing of the cathodes based on the obtained materials are presented. The complex metal oxides LiNi_0.33Mn_0.33Co_0.33O₂ prepared by sol–gel processes and thermal destruction of metal-containing compounds in oil consist of primary nanosized crystallites with an average size of 90 nm covered by a nanometer carbon layer, which improves the electrochemical characteristics of lithium ion batteries.     

Effects of Mg,Al Co-doping into Mn site on electrochemical performance of LiNi<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript>

In order to study the influence of multiple ions doping into single-site on the structure and electrochemical properties of Ni-rich layered-structure cathode material LiNi_0.5Co_0.2Mn_0.3O₂, the coprecipitation of hydroxides was applied to synthesize Mg, Al co-doped cathode material LiNi_0.5Co_0.2Mn_0.3–x Mg_1/2x Al_1/2x O₂ (x = 0.00, 0.01, 0.02, 0.04) in this paper. Morphology and structure, kinetic parameter, impedance and electrochemical performance of the material were respectively characterized by SEM, XRD, CV, EIS and galvanostatic charge/discharge test. The results of comprehensive analysis showed that the properties of material were improved obviously when the amount of doping was 0.02. At this amount of doping, the corresponding material has smaller cation mixing, higher hexagonal ordering of layered-structure, larger Li⁺ ion diffusion coefficients which are 2.444 × 10^–10 and 4.186 × 10^–10 cm² s^–1 for Li+ intercalation and deintercalation respectively, smaller impedance which is 33.93 Ω, higher specific capacity of first-discharge which is 168.01 mA h g^–1 and higher capacity retention rate which is up to 95.06% after 20 cycles at 0.5 C (100 mA g^–1).     

Effects of Nb substitution on structure and electrochemical properties of LiNi<Subscript>0.7</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript> cathode materials

Nb-doped cathode materials with the formula Li(Ni_0.7Mn_0.3)_1?xNb_xO₂ (x?=?0, 0.01, 0.02, 0.03, 0.04) have been prepared successfully by calcining the mixtures of LiOH·H₂O, Nb₂O₅, and Ni_0.7Mn_0.3(OH)₂ precursor formed through a simple continuous co-precipitation method. The effects of Nb substitution on the crystal structure and electrochemical properties of LiNi_0.7Mn_0.3O₂ were studied systematically by X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and various electrochemical measurements. The results show that the lattice parameters of the Nb substitution LiNi_0.7Mn_0.3O₂ samples are slightly larger than that of pure LiNi_0.7Mn_0.3O₂, and the basic α-NaFeO₂ layered structure does not change with the Nb doping. What’s more, better morphology, lower resistance, and good cycle stability were obtained after Nb substitution. In addition, CV test exhibits that Nb doping results in lower electrode polarization and XPS results indicate that the valence of Mn kept constant but the component of Ni³⁺ decreased after doping. All the results indicate that Nb doping in LiNi_0.7Mn_0.3O₂ is a promising method to improve the properties of Ni-rich lithium-ion batteries positive-electrode materials.     

Co-precipitation spray-drying synthesis and electrochemical performance of stabilized LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode materials

In this paper, the LiNi_0.5Mn_1.5O₄ cathode materials of lithium-ion batteries are synthesized by a co-precipitation spray-drying and calcining process. The use of a spray-drying process to form particles, followed by a calcination treatment at the optimized temperature of 750 °C to produce spherical LiNi_0.5Mn_1.5O₄ particles with a cubic crystal structure, a specific surface area of 60.1 m² g^?1, a tap density of 1.15 g mL^?1, and a specific capacity of 132.9 mAh g^?1 at 0.1 C. The carbon nanofragment (CNF) additives, introduced into the spheres during the co-precipitation spray-drying period, greatly enhance the rate performance and cycling stability of LiNi_0.5Mn_1.5O₄. The sample with 1.0 wt.% CNF calcined at 750 °C exhibits a maximum capacity of 131.7 mAh g^?1 at 0.5 C and a capacity retention of 98.9% after 100 cycles. In addition, compared to the LiNi_0.5Mn_1.5O₄ material without CNF, the LiNi_0.5Mn_1.5O₄ with CNF demonstrates a high-rate capacity retention that increases from 69.1% to 95.2% after 100 cycles at 10 C, indicating an excellent rate capability. The usage of CNF and the synthetic method provide a promising choice for the synthesis of a stabilized LiNi_0.5Mn_1.5O₄ cathode material.

Open image in new window

Graphical Abstract Micro/nanostructured LiNi_0.5Mn_0.5O₄ cathode materials with enhanced electrochemical performances for high voltage lithium-ion batteries are synthesized by a co-precipitation spray-drying and calcining routine and using carbon nanofragments (CNFs) as additive.

     

Synthesis and electrochemical performance of the Li-rich cathode material Li<Subscript>1.17</Subscript>Ni<Subscript>0.12</Subscript>Co<Subscript>0.13</Subscript>Mn<Subscript>0.58</Subscript>O<Subscript>2</Subscript> for lithium-ion batteries

Lithium-riched cathode material for lithium-ion batteries, Li_1.17Ni_0.12Co_0.13Mn_0.58O₂, was synthesized via crystallization from a solution of metal acetates, followed by a thermal treatment of the material obtained as a powder. The phase, elemental, and granulometric compositions of the material were examined, as well as the morphology of the powder particles obtained. The discharge capacity of the material in relation to the charging voltage was found from the results of electrochemical tests, and endurance tests were performed. The discharge capacity upon 85 charge/discharge cycles at voltages in the range 2.8–4.8 and a current of 0.1C was about 180 mA h g^–1.     

Improvement of the electrochemical properties of a LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode material formed by a new solid-state synthesis method

In order to avoid the shortcomings of large particle size and poor uniformity of material synthesized by the traditional solid-state method, this paper utilizes a simple improvement of calcination process (i.e., calcination–milling–recalcination) based on the traditional solid-state synthesis to successfully prepare a large number of well-distributed, micrometer-sized, spherical secondary LiNi_0.5Mn_1.5O₄ particles. Each particle is composed of nano- and/or sub-micrometer-sized grains. Results of the electrochemical performance tests show that the material exhibits a remarkable cycle performance and rate capability compared with that obtained from traditional synthesis method; the spherical LiNi_0.5Mn_1.5O₄ particles can deliver a large capacity of 135.8 mAh g^?1 at a 1 C discharge rate with a high retention of 77 % after 741 cycles and a good capacity of 105.9 mAh g^?1 at 10 C. Cyclic voltammetry measurements confirm that the significantly improved electrochemical properties are due to enhanced electronic conductivity and lithium-ion diffusion coefficient resulting from the optimized morphology and particle size. This improved method is more suitable for mass production.     

Effect of lithium boron oxide glass coating on the electrochemical performance of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript>

The effect of the lithium boron oxide glass coating on the electrochemical performance of LiNi_1/3Co_1/3Mn_1/3O₂ has been investigated via solution method. The morphology, structure, and electrochemical properties of the bare and coated LiNi_1/3Co_1/3Mn_1/3O₂ are characterized by scanning electron microscopy, X-ray diffraction, electrochemical impedance spectroscopy, and charge–discharge tests. The results showed that the lattice structure of LiNi_1/3Co_1/3Mn_1/3O₂ is not changed after coating. The coating sample shows good high-rate discharge performance (148 mAh g⁻¹ at 5.0 C rate) and cycling stability even at high temperature (with the capacities retention about 99% and 87% at room and elevated temperature after 50 cycles). The Li⁺ diffusion coefficient is also largely improved, while the charge transfer resistance, side reactions within cell, and the erosion of Hydrofluoric Acid all reduced. Consequently, the good electrochemical performances are obtained.     

Al,B, and F doped LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> as cathode material of lithium-ion batteries

A series of the mixed transition metal compounds, Li[(Ni_1/3Co_1/3Mn_1/3)_1–x-y Al _x B _y ]O_2-z F _z (x = 0, 0.02, y = 0, 0.02, z = 0, 0.02), were synthesized via coprecipitation followed by a high-temperature heat-treatment. XRD patterns revealed that this material has a typical α-NaFeO₂ type layered structure with R3^- m space group. Rietveld refinement explained that cation mixing within the Li(Ni_1/3Co_1/3Mn_1/3)O₂ could be absolutely diminished by Al-doping. Al, B and F doped compounds showed both improved physical and electrochemical properties, high tap-density, and delivered a reversible capacity of 190 mAh/g with excellent capacity retention even when the electrodes were cycled between 3.0 and 4.7 V.     

Influence of ZnO coating on the structure,morphology and electrochemical performances for LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> material

In this paper, ZnO was applied to modify the surface of LiNi_1/3Co_1/3Mn_1/3O₂ cathode material by a simple method. Powder X-ray diffraction (XRD) results show that both of the pristine material and the modified material were well crystallized and closely similar to each other. The crystal parameters of pristine material increased by modified measure. Scan electron microscope (SEM) pictures exhibit that the quasispherical pristine material was modified to the squareness one. Transmission electron microscope (TEM) image clearly elucidates that ZnO (several nanometers to 20 nm) was successful coated on surface of LiNi_1/3Co_1/3Mn_1/3O₂. X-ray photo-electron spectrometry (XPS) is used to characterize the composite of the coating layer on the surface of modified material. Electrochemical performance results present that the ZnO coating layer decrease the initial capacities of LiNi_1/3Co_1/3Mn_1/3O₂ by increasing the surface layer resistances. However, the cycling performance of LiNi_1/3Co_1/3Mn_1/3O₂ was effectively improved by the ZnO coating layer.     

LiNi<Subscript>0.8</Subscript>Co<Subscript>0.2−x</Subscript>Ti<Subscript>x</Subscript>O<Subscript>2</Subscript> nanoparticles: synthesis,structure, and evaluation of electrochemical properties for lithium ion cell application

Layered Ti-doped lithiated nickel cobaltate, LiNi_0.8Co_{0.2 − x}Ti_xO₂ (where x = 0.01, 0.03, and 0.05) nanopowders were prepared by wet-chemistry technique. The structural properties of synthesized materials were characterized by X-ray diffraction (XRD) and thermo-gravimetric/differential thermal analysis (TG/DTA). The morphological changes brought about by the changes in composition of LiNi_0.8Co_{0.2 − x}Ti_xO₂ particles were examined through surface examination techniques such as scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses. Electrochemical studies were carried out using 2016-type coin cell in the voltage range of 3.0–4.5 V (vs carbon) using 1 M LiClO₄ in ethylene carbonate and diethyl carbonate as the electrolyte. Among the various concentrations of Ti-doped lithiated nickel cobaltate materials, C/LiNi_0.8Co_0.17Ti_0.03O₂ cell gives stable charge–discharge features.     

Improving rate performance of cathode material Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Co<Subscript>0.13</Subscript>Ni<Subscript>0.13</Subscript>O<Subscript>2</Subscript> via niobium doping

As a promising Li-ion battery cathode active material, lithium-rich manganese-based layer-structured oxides suffer from inferior cycle performance and poor rate capability. Herein, Nb-doped Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ is prepared by a sol-gel method, and the effects of Nb doping on its electrochemical performance are investigated. It is concluded that the Nb-doped Li_1.2Mn_0.54Ni_0.13Co_0.13O₂, has a good layered structure along c-axis independent on the amount of Nb dopant and little cationic mixing. Nb doping for Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ has no obvious influence on its morphology. It is found that Nb doping can enhance the electrochemical activity of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂, such as improved rate performance and cycle performance under high rate conditions. Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ doped with 0.015 Nb shows the best cycle performance under the high rate with the capacity maintenance of 95.4% after 100 cycles under 5 C rate, which is higher than that of the undoped one by 10.5%.

Open image in new window

Graphical abstract Rate performance of Li_1.2Mn_0.54-xCo_0.13Ni_0.13Nb _x O₂ materials

     

Composition of the gas phase over Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and the enthalpies of atomization of AlO,Al<Subscript>2</Subscript>O,and Al<Subscript>2</Subscript>O<Subscript>2</Subscript>

The A1, O, AlO, A1₂O, Al₂O₂, WO₂, and WO₃, partial pressures in the vapor over Al₂O₃ in a tungsten Knudsen effusion cell between 2300 and 2600 K were derived from A1⁺, O⁺, AlO⁺, A1₂O⁺, Al₂O₂⁺, WO₂⁺, and WO₃⁺, ion intensities. The mass spectrometer was calibrated against the equilibrium constant of the WO₃(g) = WO₂(g) + O(g) reaction. Refined values of the ionization cross sections of AlO and A1₂O₂ were used in the partial pressure calculations. The enthalpies of atomization of aluminum suboxides were determined to be Δ_at H ^o(AlO, g, 0) = 510.7 ± 3.3 kJ mol⁻¹, Δ_at H ^o(Al₂O, g, 0) = 1067.2 ± 6.9 kJ mol⁻¹, and Δ_at H ^o(Al₂O₂, g, 0) = 1556.7 ± 9.9 kJ mol⁻¹.     

Sn-doped Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> cathode materials for lithium-ion batteries with enhanced electrochemical performance

Sn-doped Li-rich layered oxides of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ have been synthesized via a sol-gel method, and their microstructure and electrochemical performance have been studied. The addition of Sn⁴⁺ ions has no distinct influence on the crystal structure of the materials. After doped with an appropriate amount of Sn⁴⁺, the electrochemical performance of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ cathode materials is significantly enhanced. The optimal electrochemical performance is obtained at x = 0.01. The Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode delivers a high initial discharge capacity of 268.9 mAh g^?1 with an initial coulombic efficiency of 76.5% and a reversible capacity of 199.8 mAh g^?1 at 0.1 C with capacity retention of 75.2% after 100 cycles. In addition, the Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode exhibits the superior rate capability with discharge capacities of 239.8, 198.6, 164.4, 133.4, and 88.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively, which are much higher than those of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ (196.2, 153.5, 117.5, 92.7, and 43.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively). The substitution of Sn⁴⁺ for Mn⁴⁺ enlarges the Li⁺ diffusion channels due to its larger ionic radius compared to Mn⁴⁺ and enhances the structural stability of Li-rich oxides, leading to the improved electrochemical performance in the Sn-doped Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ cathode materials.     

Solid-phase synthesis of intermetallic compounds Al<Subscript>13</Subscript>Co<Subscript>4</Subscript>, Al<Subscript>13</Subscript>Fe<Subscript>4</Subscript>, and Al<Subscript>13</Subscript>Co<Subscript>2</Subscript>Fe<Subscript>2</Subscript>

Intermetallic compounds Al₁₃Co₄, Al₁₃Fe₄, and Al₁₃Co₂Fe₂ were obtained by solid-phase synthesis in air at temperatures below 600°C using precursor metals subjected to mechanochemical preactivation. The phase composition of the synthesized aluminides and composites Al₁₃Co₄/SiO₂ and Al₁₃Fe₄/SiO₂ was analyzed.     

BiFeO<Subscript>3</Subscript>-coated spinel LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> with improved electrochemical performance as cathode materials for lithium-ion batteries

Spinel LiNi_0.5Mn_1.5O₄ cathode material is a promising candidate for next-generation rechargeable lithium-ion batteries. In this work, BiFeO₃-coated LiNi_0.5Mn_1.5O₄ materials were prepared via a wet chemical method and the structure, morphology, and electrochemical performance of the materials were studied. The coating of BiFeO₃ has no significant impact on the crystal structure of LiNi_0.5Mn_1.5O₄. All BiFeO₃-coated LiNi_0.5Mn_1.5O₄ materials exhibit cubic spinel structure with space group of Fd3m. Thin BiFeO₃ layers were successfully coated on the surface of LiNi_0.5Mn_1.5O₄ particles. The coating of 1.0 wt% BiFeO₃ on the surface of LiNi_0.5Mn_1.5O₄ exhibits a considerable enhancement in specific capacity, cyclic stability, and rate performance. The initial discharge capacity of 118.5 mAh g^?1 is obtained for 1.0 wt% BiFeO₃-coated LiNi_0.5Mn_1.5O₄ with very high capacity retention of 89.11% at 0.1 C after 100 cycles. Meanwhile, 1.0 wt% BiFeO₃-coated LiNi_0.5Mn_1.5O₄ electrode shows excellent rate performance with discharge capacities of 117.5, 110.2, 85.8, and 74.8 mAh g^?1 at 1, 2, 5, and 10 C, respectively, which is higher than that of LiNi_0.5Mn_1.5O₄ (97.3, 90, 77.5, and 60.9 mAh g^?1, respectively). The surface coating of BiFeO₃ effectively decreases charge transfer resistance and inhibits side reactions between active materials and electrolyte and thus induces the improved electrochemical performance of LiNi_0.5Mn_1.5O₄ materials.     

Synthesis and characterization of Co<Subscript>0.8</Subscript>Zn<Subscript>0.2</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles

Cobalt zinc ferrite, Co_0.8Zn_0.2Fe₂O₄, nanoparticles have been synthesized via autocatalytic decomposition of the precursor, cobalt zinc ferrous fumarato hydrazinate. The X-ray powder diffraction of the ‘as prepared’ oxide confirms the formation of single phase nanocrystalline cobalt zinc ferrite nanoparticles. The thermal decomposition of the precursor has been studied by isothermal, thermogravimetric and differential thermal analysis. The precursor has also been characterized by FTIR, and chemical analysis and its chemical composition has been determined as Co_0.8Zn_0.2Fe₂(C₄H₂O₄)₃·6N₂H_4. The Curie temperature of the ‘as-prepared oxide’ was determined by AC susceptibility measurements.