Simple chemical route for nanorod-like cobalt oxide films for electrochemical energy storage applications

We used a simple chemical synthesis route to deposit nanorod-like cobalt oxide thin films on different substrates such as stainless steel (ss), indium tin oxide (ITO), and microscopic glass slides. The morphology of the films show that the films were uniformly spread having a nanorod-like structure with the length of the nanorods shortened on ss substrates. The electrochemical properties of the films deposited at different time intervals were studied using cyclic voltammetry (CV), galvanostatic charge–discharge (GCD), and electrochemical impedance spectroscopy (EIS). The film deposited after 20 cycles on ss gave the highest specific capacity of 67.6 mAh g^?1 and volumetric capacity of 123 mAh cm^?3 at a scan rate 5 mV s^?1 in comparison to 62.0 mAh g^?1 and 113 mAh cm^?3 obtained, respectively, for its counterpart on ITO. The film electrode deposited after 20 cycles on ITO gave the best rate capability and excellent cyclability with no depreciation after 2000 charge–discharge cycles.     

Effect of cyclic oxidation on electrochemical corrosion of type 409 stainless steel in the simulated muffler condensates

The electrochemical corrosion behavior of 409 stainless steel after cyclic oxidation below 400 °C was investigated in the simulated muffler condensates by using surface analysis and electrochemical measurement techniques. In the cyclic processes of condensate-dipping and oxidation, specimens may form defective oxide films and weak Cr depletion underlying the oxide films. Sulfate from the condensate-dipping will give rise to sulfidation during the cyclic oxidation, being detrimental to both the oxidation and corrosion properties of stainless steel. The oxidation above 300 °C deteriorates the corrosion resistance, even leading to active corrosion in the acidic condensate solutions. Comparatively, specimens oxidized cyclically without condensate-dipping show much higher condensate corrosion resistance. It is suggested that the acidic condensate corrosion is accelerated by the synergetic effect of oxidation and condensation in the mufflers, and then may result in perforation through the defects such as cracks and nodules in oxide films on the stainless steel surface.     

Enhancing effect of boron trifluoride diethyl etherate electrolytes on capacitance performance of electropolymerized poly[poly(<Emphasis Type="Italic">N</Emphasis>-vinyl-carbazole)] films

In this paper, poly[poly(N-vinyl-carbazole)] (PPVK) films electrodeposited in tetrahydrofuran (THF) containing 12 % boron trifluoride diethyl etherate (BFEE) were studied as electrode active material for supercapacitors. The morphology and thermal property were characterized by SEM, atomic force microscopy (AFM), and thermogravimetry (TG), respectively. The electrochemical capacitive behaviors of the PPVK films were also investigated by cyclic voltammetry, galvanostatic charge/discharge, and electrochemical impedance spectroscopy. The electrochemical results showed that the specific capacitance of PPVK films in CH₃CN solution was about 126 mF cm^?2 at 1.5 mA cm^?2 and the capacitance retention was only 14.4 % after 1000 cycles. It was exciting to improve the specific capacitance up to 169.3 mF cm^?2 at 1.5 mA cm^?2 and to make the cyclic stability increase to 81.8 % capacitance retention after 5000 cycles when the equivalent BFEE was added into the CH₃CN solution containing 0.05 M Bu₄NBF₄ electrolyte. These results clearly demonstrated that BFEE was an efficient promoter for the enhancement of the capacitance performance of PPVK films. Therefore, with the help of BFEE electrolyte, the PPVK films have potential application as capacitive materials in high-performance energy storage devices.     

Electrochemical polymerization of polyaniline doped with Zn2+ as the electrode material for electrochemical supercapacitors

Polyaniline doped with Zn²⁺ (PANI/Zn²⁺) films was synthesized by cyclic voltammetric method on stainless steel mesh substrates in 0.2 mol L^?1 aniline and 0.5 mol L^?1 sulfuric acid electrolyte with various concentrations of zinc sulfate (ZnSO₄·7H₂O). The structure and morphology of PANI and PANI/Zn²⁺ films were characterized by Fourier transform infrared, X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy techniques, respectively. The electrochemical properties of PANI and PANI/Zn²⁺ films were investigated by cyclic voltammetry, galvanostatic charge–discharge test, and electrochemical impedance spectroscopy in 0.5 mol L^?1 H₂SO₄ electrolyte in a three-electrode system. The results show that the surface morphology of PANI/Zn²⁺ is more rough than that of pure PANI. The specific capacitance of the PANI/Zn²⁺ film displays a larger specific capacitance of 738 F g^?1, lower resistance, and better stability as compared with the pure PANI film. Thus, good capacitive performance demonstrates its potential superiority for supercapacitors.     

Comparison of electrochemical properties of two-component C60-Pd polymers formed under electrochemical conditions and by chemical synthesis

The electrochemical behavior of C₆₀-Pd polymer formed under electrochemical conditions and by the chemical synthesis was examined. In these polymers, fullerene moieties are covalently bonded to palladium atoms to form a polymeric network. Both materials deposited at the electrode surface show electrochemical activity at negative potentials due to the reduction of fullerene cage. Electrochemically formed thin polymeric films exhibit much more reversible voltammetric response in comparison to chemically synthesized polymers. The morphology and electrochemical behavior of chemically synthesized C₆₀-Pd polymer depend on the composition of grown solution. Chemical polymerization results in formation of large, ca. 50 μm, crystallic superficial structures that are composed of regular spherical particles with a diameter of 150 nm. The capacitance properties of C₆₀-Pd films were investigated by cyclic voltammetry and faradaic impedance spectroscopy. Specific capacitance of chemically formed films depends on the conditions of film formation. The best capacitance properties was obtained for films containing 1:3 fullerene to Pd molar ratio. For these films, specific capacitance of 35 Fg^?1 was obtained in acetonitrile containing (n-C₄H₉)₄NClO₄. This value is much lower in comparison to the specific capacitance of electrochemically formed C₆₀-Pd film.     

Graphene oxide decorated bimetal (MnNi) oxide nanoflakes used as an electrocatalyst for enhanced oxygen evolution reaction in alkaline media

Precious non-noble metals have been constantly attracting research attention in order to realize an inexpensive, extra active and more stable electrocatalysts in terms of various oxidation states and structures for their applications in oxidation (splitting) of water. In the present work graphene oxide incorporated, MnO₂-NiO composite metal oxide nanoflakes were synthesized on the stainless steel substrate using efficient electrodeposition route in alkaline media and drop casting method with further annealing treatment at 400 °C for 4 h. Initially MnO₂-NiO nanoflakes were deposited using different cyclic sweep rates, later graphene oxide suspension was drop casted on the MnO₂-NiO nanoflakes and subsequently subjected to annealing at 200 °C for 2 h. The prepared electrode material is denoted as GO/MnO₂-NiO/SS and used as an electrocatalyst for oxygen evolution. Field emission scanning electron microscopy, transmission electron microscopy, Energy dispersive electron spectroscopy and X-ray diffraction spectroscopy were used to study the crystalline nature and morphologies of the deposited films. The electrochemical properties of the electrode material were investigated using cyclic voltammetry and linear sweep voltammetry. The electrode exhibits low overpotential and small Tafel slope of 379 mV and 47.84 mVdec⁻¹ at the current density of 10 mA cm⁻² in alkaline (KOH) medium. In addition, the electrode shows a long time stability of 28800 s. Hence, the present study suggests that the GO incorporated Mn-Ni bimetal oxide modified electrode is suitable electrode material for oxygen evolution reaction (OER), owing to its facile preparation, inexpensive, easy handling and high active nature.     

α-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> thin films by liquid phase deposition: low-cost option for supercapacitor

In the present study, iron oxide (α-Fe₂O₃) thin films with good adhesion on stainless steel substrates are deposited by liquid phase deposition (LPD) technique, which is additive and binder-free. Iron oxyhydroxide (FeOOH) thin films are formed by means of a ligand-exchange equilibrium reaction of metal-fluoro complex ions and an F^?ions consuming reaction by using boric acid (H₃BO₃) as a scavenging agent. These films are annealed at 500 °C to get α-Fe₂O₃ thin films. The transformation from hydrophobic to hydrophilic nature of the films is observed due to annealing. The films are characterized by different techniques. The α-Fe₂O₃ film is checked for electrochemical supercapacitive performance in Na₂SO₃ solutions of various concentrations. Specific capacitance is calculated from cyclic voltammetry at numerous scan rates (5–200) mV s^?1. The highest obtained value of specific capacitance is 582 F g^?1 at 5 mV s^?1 for 0.5 M Na₂SO₃ electrolyte. The maximum values of specific power and specific energy are 6.9 and 53.4 Wh kg^?1 from the charge-discharge curve at the current density 2 mA cm^?2 in 0.5 M Na₂SO₃ electrolyte.     

Electrochemical Characterization of Chemically Synthesized Polythiophene Thin Films: Performance of Asymmetric Supercapacitor Device

Polythiophene (PT) thin films have been prepared by chemical bath deposition (CBD) method at room temperature (300 K) via oxidative polymerization of thiophene using ammonium peroxodisulfate (APS) as an oxidizing agent. Globular particulates of PT are deposited on the stainless steel and glass substrates. The morphology and chain structure of PT are studied using scanning electron microscopy (SEM) and Raman spectroscopy techniques, respectively. The electrochemical behavior of PT electrode is studied using cyclic voltammetry and galvanostatic charge? discharge studies. PT thin film shows maximum specific capacitance of 300 F g^?1 at 5 mV s^?1 in 0.1 M LiClO₄/PC electrolyte. The asymmetric device formed with PT and graphite shows supercapacitive properties useful in the power applications.     

Deposition of polyaniline on RVC electrodes: effect of substrate thickness

Polyaniline films, obtained by either chemical or electrochemical deposition on reticulated vitreous carbon (RVC), were investigated as a function of the substrate thickness. The electrochemical properties of these RVC/Pani electrodes were assessed by cyclic voltammetry and electrochemical impedance spectroscopy (EIS), whereas the morphology of the Pani films on RVC was analyzed by scanning electron microscopy (SEM). The cyclic voltammetric results revealed that the oxidation/reduction charges for electrodeposited polyaniline decrease as the RVC thickness is increased. Conversely, the charge densities for the chemically deposited films do not present a significant dependence on the substrate thickness. Two time constants, appearing in all the EIS spectra, indicate that an ohmic drop effect within the RVC substrate affects the polymer electrodeposition and the electrochemical behavior of the obtained electrodes. Therefore, an electric equivalent circuit considering the different electrochemical environments at the outer and inner RVC surfaces was proposed to analyze the EIS data.     

Glucose biosensor based on glucose oxidase immobilized on unhybridized titanium dioxide nanotube arrays

A glucose biosensor has been fabricated by immobilizing glucose oxidase (GOx) on unhybridized titanium dioxide nanotube arrays using an optimized cross-linking technique. The TiO₂ nanotube arrays were synthesized directly on a titanium substrate by anodic oxidation. The structure and morphology of electrode material were characterized by X-ray diffraction and scanning electron microscopy. The electrochemical performances of the glucose biosensor were conducted by cyclic voltammetry and chronoamperometry measurements. It gives a linear response to glucose in the 0.05 to 0.65 mM concentration range, with a correlation coefficient of 0.9981, a sensitivity of 199.6 μA mM^?1 cm^?2, and a detection limit as low as 3.8 µM. This glucose biosensor exhibited high selectivity for glucose determination in the presence of ascorbic acid, sucrose and other common interfering substances. This glucose biosensor also performed good reproducibility and long-time storage stability. This optimized cross-linking technique could open a new avenue for other enzyme biosensors fabrication.

Synthesis of NiO/Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocomposites as substrate for the construction of electrochemical biosensors

The exploration of substrate materials to construct electrochemical biosensors for glucose monitoring in the field of clinical diagnosis, especially for diabetes is still being investigated extensively. In this paper, NiO/Fe₂O₃ nanocomposites are designed and synthesized by two-step hydrothermal approach in combination with calcinations. The morphology and microstructure are studied by SEM, XRD, XPS, and TEM systematically. Optimized NiO/Fe₂O₃ nanocomposites are employed as substrate to construct glucose biosensors, and the electrochemical properties are carried out by cyclic voltammetric and chronoamperometric techniques. The results indicate as-prepared biosensors achieve a high sensitivity of 230.5 μA cm^?2 mM^?1, wide linear range between 50 and 2867 μM, and low detection limit of 3.9 μM towards glucose detection. The synergistic effect between NiO and Fe₂O₃ as substrate to construct glucose biosensors is elucidated. The selectivity is acceptable based on the detection of glucose concentration for diabetics.     

Self-assembled films based on polypyrrole and carbon nanotubes composites for the determination of Diuron pesticide

In this work, polypyrrole (PPy) and its respective composite with functionalized multi-walled carbon nanotubes (MWCNT) were obtained by chemical polymerization of the monomer pyrrole in aqueous solution. The obtained PPy as well as its composite (PPy-MWCNT) were characterized by Fourier transform infrared spectroscopy (FTIR) and were used to produce nanostructured self-assembled (SA) films deposited onto glass substrates covered with indium tin oxide (ITO). The SA films were produced with alternated layers of polystyrene sulphonated (PSS) and were characterized by UV-visible, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and scanning electron microscopy (SEM) analyses. The applicability of the SA films was evaluated by square wave voltammetry (SWV) with standard additions of aliquots of Diuron pesticide in Britton-Robinson buffer solutions (pH = 2.0). The results showed an oxidation peak at 0.23 V which increases in function of the Diuron concentration for both the SA films. It was also observed that the SA film based on the composite (PPy-MWCNT/PSS) showed a peak current intensity about ten times higher in comparison with its unmodified counterpart (PPy/PSS) for a Diuron concentration of 4.29 × 10^?5 mol L^?1, indicating a synergic effect between PPy and MWCNT in the composite. The limits of quantification (LOQ) and limits of detection (LOD) were respectively 8.6 × 10^?7 mol L^?1 and 2.6 × 10^?7 mol L^?1.     

Direct electrochemical detection of bisphenol A at PEDOT-modified glassy carbon electrodes

The electrochemical behavior of bisphenol A (BPA) was studied on poly(3,4-ethylenedioxythiophene) (PEDOT)-modified glassy carbon electrodes by cyclic voltammetry. It was observed that BPA oxidation on PEDOT film produced a BPA polymer (pBPA) showing excellent redox activity with anodic and cathodic peaks at 0.15 and 0.01 V, respectively; the former being evaluated for BPA electrochemical sensing. The amount of deposited pBPA has been estimated by electrochemical and spectroscopic analysis by X-ray photoelectron spectroscopy. The effect of scan rate and pH on the oxidation of pBPA film has been studied. The oxidation current was found to vary linearly with BPA concentration in the range 90–410 μM, and a detection limit of 55 μM was evaluated. Results of BPA amperometric detection have also been collected by using a repetitive potential step program to give a linear response to BPA in the concentration range 40–410 μM with a detection limit of 22 μM and a sensitivity of 1.57 μAμM^?1?cm^?2. The developed sensor showed satisfactory reproducibility and anti-interference properties and was successfully applied to BPA determination in mineral water samples.     

Electrodeposition of Al-Ti alloy on mild steel from AlCl<Subscript>3</Subscript>-BMIC ionic liquid

The electrodeposition of Al-Ti alloy on a mild steel substrate is examined in a Lewis acidic 66.7–33.3 mol% AlCl₃-1-buthyl-3-methylimidazolium chloride ionic liquid containing TiCl₄. Dense and compact Al-Ti alloy coatings with Ti content ranging from 5.3 to 11.4 at.% can be obtained under optimized conditions. The applied current densities and TiCl₄ concentration are found to play central roles in controlling the alloy compositions and surface morphologies of the resultant Al-Ti alloy coatings. Ti content in Al-Ti alloys increases with initial increase in the current density and decreases when the current density is beyond 5 mA cm^?2. In addition, the enhanced corrosion resistance of the mild steel substrate by the deposited Al-Ti alloy layers is evaluated via electrochemical techniques. The Al-Ti alloy coatings show much higher corrosion resistance than single Al coating, and this performance is improved with the increase of the Ti content.     

Intensified electrochemical hydrogen storage capacity of multi-walled carbon nanotubes supported with Ni nanoparticles

The electrochemical hydrogen storage properties of Ni-supported multi-walled carbon nanotube (Ni/MWCNT) electrodes were investigated using charge/discharge (C&D) and cyclic voltammetry (CV) techniques. Nickel NPs were deposited on the MWCNT surface, which was first chemically oxidized by H₂SO₄ and HNO₃ (3:1, v/v). Hydrogen storage was carried out by using the Ni/MWCNT electrode as the working electrode in the electrochemical cell. A set of various current densities were applied to the cell to produce (C&D) cycles, and it became optimum corresponding to 1.5 mA current. According to the electrochemical test results, the highest electrochemical discharge capacity of 1625 mAh g^?1 was obtained for the electrode with ratio of 4:1 (MWCNTs to Ni) in the initial cycle, which corresponded to 6.07 wt% H₂. The storage capacity was increased and reached to 4909 mAh g^?1 (18.34 wt% H₂) after 20 cycles, and the electrode maintained the specific capacity as cycling continued. Thus, the Ni/MWCNT electrode displays an excellent cycle stability and a high capacity reversibility. CV measurements also showed that the electrochemical adsorption and desorption amount of hydrogen was increased by Ni loading onto the CNTs and indicated that the electrochemical hydrogen adsorption of the electrode has an activated period.     

The importance of the film structure during self-powered ibuprofen salicylate drug release from polypyrrole electrodeposited on AZ31 Mg

Therapeutic drugs uploaded into conjugated conductive polymer matrices deposited on active magnesium alloys serve as controlled-dose, self-powered drug-delivery systems. Preferentially, drugs are added into polymer films in the largest amount possible, mostly to prevent long-term treatments. However, added drugs can interact with the polymer matrix affecting either the structure or the final mechanical properties of the polymer film. In this work, polypyrrole films (PPy) electrodeposited on an AZ31 Mg alloy in ibuprofen and salicylate-containing solutions are investigated in terms of their uploading capacity, surface morphology and mechanical properties. The techniques used to investigate the uploaded PPy films include cyclic voltammetry (CV), scanning electron microscopy (SEM), EDS, and depth-sensing indentation (DSI). A maximum ibuprofen concentration of 440 ± 40 μg cm^?2 was obtained in PPy films in the presence of sodium salicylate. The release fraction of ibuprofen as a function of time is fitted to Avrami’s equation. The hardness and reduced modulus decreased by 54 and 40 %, respectively, when the PPy films are prepared in the presence of sodium ibuprofen compared with those prepared in sodium salicylate only, indicating a more plastic film with ibuprofen.     

Optical,electrical, and electrochemical behavior of p-type nanostructured SnO<Subscript>2</Subscript>:Ni (NTO) thin films

The physical and electrochemical properties of sol-gel synthesized nickel-doped tin oxide (NTO) thin films were investigated. The X-ray diffraction results showed that NTO samples exhibited a tetragonal structure. The average crystallite size and the unit cell volume of the films were reduced by Ni increment, while the stacking fault probability was increased. Furthermore, the field-emission scanning electron microscopy images clearly displayed that the worm-like surface morphology of the SnO₂ thin films was altered to the spherical feature in 3 and 10 mol% NTO samples. Moreover, by virtue of Ni incorporation, the average transparency of the SnO₂ thin films rose up from 67 to 85% in the visible region; also, the optical band gap of the SnO₂ sample (3.97 eV) increased and the thin film with 3 mol% dopant concentration showed a maximum value of 4.22 eV. The blue/green emission intensities of photoluminescence spectra of SnO₂ thin film changed via Ni doping. The Hall effect measurements revealed that by Ni addition, the electrical conductivity of tin oxide thin films altered from n- to p-type and the carrier concentration of the films decreased due to the role of Ni²⁺ ions which act as electron acceptors in NTO films. In contrast, 20 mol% Ni-doped sample had the highest mobility about 9.65 cm² (V s)^?1. In addition, the cyclic voltammogram of NTO thin films in KOH electrolyte indicated the charge storage capacity and the surface total charge density of SnO₂ thin films enhanced via Ni doping. Moreover, the diffusion constant of the samples increased from 2?×?10^?15 to 6.5?×?10^?15 cm² s^?1 for undoped and 5 mol% dopant concentration. The electrochemical impedance spectroscopy of the NTO thin films in two different potentials showed the different electrochemical behaviors of n- and p-type thin films. It revealed that the 20 mol% NTO thin film had maximum charge transfer at lower applied potential.     

Effect of synthesis duration on the morphological and structural modification of the sea urchin-nanostructured γ-MnO2 and study of its electrochemical reactivity in alkaline medium

Single-crystalline nanorods and sea urchin-like morphology of the γ-MnO₂ nanostructures were successfully synthesized by hydrothermal method at different synthesis durations. The as-synthesized products were characterized by the techniques X-ray powder diffraction (XRD), field emission gun-scanning electron microscope (FEG-SEM) coupled with energy-dispersive X-ray elemental analysis (EDX), transmission electron microscope (TEM), isotherms of N₂ adsorption/desorption and BET-BJH models. The effect of synthesis duration on the morphology, porous structure, and crystallographic form of MnO₂ powders was studied. The electrochemical reactivity of as-prepared powders was investigated in 1 mol L^?1 KOH by both cyclic voltammetry and impedance spectroscopy by using a micro-cavity electrode. The results show that the best electrochemical reactivity of the MnO₂ powder was obtained with synthesis duration of 24 h.     

The effect of the polyaniline morphology on the performance of polyaniline supercapacitors

The polyaniline (PANI) prepared by the pulse galvanostatic method (PGM) or the galvanostatic method on a stainless steel substrate from an aqueous solution of 0.5 mol/l H₂SO₄ with 0.2 mol/l aniline has been studied as an electroactive material in supercapacitors. The electrochemical performance of the PANI supercapacitor is characterized by cyclic voltammetry, a galvanostatic charge–discharge test and electrochemical impedance spectroscopy in NaClO₄ and HClO₄ mixed electrolyte. The results show that PANI films with different morphology and hence different capacitance are synthesized by controlling the synthesis methods and conditions. Owing to the double-layer capacitance and pseudocapacitance increase with increasing real surface area of PANI, the capacitive performances of PANI were enhanced with increasing real surface area of PANI. The highest capacitance is obtained for the PANI film with nanofibrous morphology. From charge–discharge studies of a nanofibrous PANI capacitor, a specific capacitance of 609 F/g and a specific energy density of 26.8 Wh/kg have been obtained at a discharge current density of 1.5 mA/cm². The PANI capacitor also shows little degradation of capacitance after 1,000 cycles. The effects of discharge current density and deposited charge of PANI on capacitance are investigated. The results indicate that the nanofibrous PANI prepared by the PGM is promising for supercapacitors.     

Fabrication and the electrochemical activation of network-like MnO<Subscript>2</Subscript> nanoflakes as a flexible and large-area supercapacitor electrode

Porous network-like MnO₂ thick films are successfully synthesized on a flexible stainless steel (SS) mesh using a simple and low-cost electrodeposition method followed by an electrochemical activation process. Morphology, chemical composition, and crystal structure of the prepared electrodes before and after the activation process are determined and compared by scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD) analyses. The results show that the implementation of the electrochemical activation process does not change the chemical composition and crystal structure of the films, but it influences the surface morphology of the MnO₂ thick layer to a flaky nanostructure. Based on the electrochemical data analysis, the maximum specific capacitance of 1400 mF (381 F g^?1) and 3700 mF (352 F g^?1) are measured for small (2.6 cm²) and large (10 cm²) surface area electrodes, respectively. In addition, a flexible symmetric MnO₂//MnO₂ solid-state supercapacitor shows a capacitance of 0.3 F with about 98% retention at different bending angles from 0 to 360°.