温度和溶液pH值交互作用对X80钢在模拟土壤环境中腐蚀行为的影响

利用循环伏安法（CV）、电化学阻抗谱（EIS）和Mott-Schottky曲线研究了温度和溶液pH值交互作用下X80钢在模拟土壤环境中的腐蚀性能。结果表明：低pH值条件下X80钢表面会形成一层稳定性差的腐蚀膜;高pH值条件下X80钢表面会形成一层保护性强的腐蚀膜。随着pH值得增大和温度的降低X80钢表面所成腐蚀膜的膜电阻和传递电阻增大,这表明随着pH值得增大和温度的降低X80钢表面所成腐蚀膜对基体的保护性增强。X80钢在模拟土壤环境中表面所成腐蚀膜呈n型半导体特性,膜内施主密度随介质pH值增大而降低,随溶液温度升高而增大。平带电位和pH值之间呈现线性关系。     

镁合金在含F－的NaOH溶液中钝化行为的电化学研究

采用极化曲线、电容-电位曲线、Mott-Schottky分析以及电化学阻抗(EIS)等电化学方法研究了镁合金在含F^－ NaOH溶液中的阳极钝化行为. 结果表明, 在－1.2～1.8 V的电位范围内, 镁合金在含F^－的NaOH溶液中发生阳极钝化. 所形成的钝化膜表现出n型半导体的导电特性. 在0.7～1.8 V的电位范围内, 随着F^－浓度增大, 镁合金的阳极极化电流密度呈现出随着电位升高而逐渐增大的趋势, 随着F^－浓度增大这一趋势逐渐减弱. 并且F^－浓度的增大使得镁合金表面空间电荷层电容和钝化膜的载流子密度都不断减小. 通过极化曲线和电化学阻抗共同说明, 在5%的Na₂SO₄溶液中, NaOH溶液中阳极钝化后的镁合金随着钝化体系中F^－浓度的增加其耐蚀性逐渐减弱.     

铬对碳钢在NaHCO3/NaCO3缓冲溶液中所成钝化膜半导体性能的影响

应用电化学阻抗谱技术研究铬对碳钢钝化膜半导体性能的影响.实验表明,在碳酸氢钠/碳酸钠缓冲溶液中碳钢形成的钝化膜具n型半导体特性,而含有3%铬的碳钢钝化膜则呈n-p型半导体特性,随着成膜电位的增加,以上两种钝化膜之Mott-Schottky直线部分的斜率均呈增大的趋势,表明成膜电位升高,膜内的杂质密度减小,但铬的加入使得碳钢钝化膜的施主密度增加约一个数量级,从而增加了碳钢点蚀发生的趋势.EIS分析表明:铬的加入降低了钝化膜的传递电阻R1和膜电阻R2,特别是膜电阻R2下降达3个数量级,这就有可能增加碳钢在高pH值环境中的腐蚀.     

温度、pH值和氯离子对X80钢钝化膜内点缺陷扩散系数的影响

借助于Mott-Schottky和点缺陷模型(PDM)研究了溶液温度、pH值以及氯离子对X80管线钢在模拟土壤环境中所形成钝化膜内点缺陷扩散系数D₀的影响. 结果表明: 随着溶液温度的升高、溶液pH值的降低以及氯离子浓度的增大, 钝化膜内的施主密度呈现增大的趋势. 依据点缺陷模型可以得到钝化膜内点缺陷(假设点缺陷为氧空位或铁离子间隙)的扩散系数D₀达到10^－16～10^－17 cm²•S^－1, 且D₀随着溶液温度的升高、溶液pH值的降低及氯离子浓度的增加而增大.     

扫描电化学显微镜原位表征pH值对核电蒸汽发生器合金腐蚀行为的影响

用扫描电化学显微镜(SECM)和电化学阻抗谱(EIS)原位表征了溶液pH值对核电蒸汽发生器800 合金溶液中的腐蚀行为的影响. 实验结果表明：在酸性氯化钠溶液中,SECM探针渐进曲线为正反馈,表明800合金为活化阳极溶解,腐蚀电位下的EIS 图呈现完整的单容抗弧特征;而在中性或者碱性溶液中,SECM探针渐进曲线为负反馈,表明800 合金为自钝化,不同阳极电位下的EIS 图均呈现不完整的容抗弧特征,但随着阳极极化电位的增加,EIS 谱容抗弧半径减小,表明钝化膜的耐蚀性下降;SECM二维扫描图像结果显示探针电流增加,表明电极表面活性增加,即钝化膜的溶解速度增加. 而在中性或者碱性溶液中的SECM二维图像中均可观察到若干活性点,这可能与晶界或者金属夹杂物等有关.     

扫描电化学显微镜原位表征pH值对核电蒸汽发生器合金腐蚀行为的影响(英文)

用扫描电化学显微镜(SECM)和电化学阻抗谱(EIS)原位表征了溶液pH值对核电蒸汽发生器800合金溶液中的腐蚀行为的影响.实验结果表明:在酸性氯化钠溶液中,SECM探针渐进曲线为正反馈,表明800合金为活化阳极溶解,腐蚀电位下的EIS图呈现完整的单容抗弧特征;而在中性或者碱性溶液中,SECM探针渐进曲线为负反馈,表明800合金为自钝化,不同阳极电位下的EIS图均呈现不完整的容抗弧特征,但随着阳极极化电位的增加,EIS谱容抗弧半径减小,表明钝化膜的耐蚀性下降;SECM二维扫描图像结果显示探针电流增加,表明电极表面活性增加,即钝化膜的溶解速度增加.而在中性或者碱性溶液中的SECM二维图像中均可观察到若干活性点,这可能与晶界或者金属夹杂物等有关.     

锡含量对铅锡合金在硫酸溶液中钝化膜性能的影响

利用线性电位扫描法(LSV)、循环伏安法(CV)和交流伏安法(ACV), 结合Mott-Schottky分析, 研究了锡含量对铅锡合金在硫酸溶液中形成的钝化膜性能的影响. 结果表明: 铅合金中加入Sn可以显著提高其耐腐蚀性能、减小其阳极膜电阻, 同时这些性能的改善随Sn含量的增加更为显著, 另外氧在铅合金上的析出过电位随合金中锡含量的增加而增加. Mott-Schottky分析表明, 钝化膜呈n型半导体特征, 钝化膜中缺陷浓度随锡含量的增加而增加, 说明其施主密度N_D和膜的导电性能随锡含量的增加而增加.     

ZnO-Bi2O3二元陶瓷粉体电化学行为研究

采用电化学阻抗谱和电位-电容测试及Mott-Schottky分析技术研究了ZnO-Bi2O3粉体电极在0.5 mol/L NaCl溶液中的电化学行为. 研究表明, ZnO-Bi2O3粉体表现为n型半导体; 随着Bi2O3含量的增加或混合时间的延长, 粉体的阻抗增大, 空间电荷层电容Csc减小, 载流子浓度ND减小; 经高温烧结成二元压敏陶瓷, 随着混合时间的延长, 电阻片综合电性能越好. 该方法可有效评价二元陶瓷粉体混合均匀性.     

锂在高有序热解石墨(HOPG)电极中的扩散系数

用循环伏安、交流阻抗和电位阶跃法研究了平板高有序热解石墨(HOPG)电极在1mol/LLiPF₆和体积比为1∶1的EC/DMC溶液中的电化学行为.结果表明,石墨的嵌锂反应仅发生在边界面上.随着嵌锂量的增加,表面SEI膜的电阻和嵌入反应的极化电阻减小.用交流阻抗谱和电位阶跃方法测定的锂在高有序热解石墨中的扩散系数一致,并随充电程度的增加而显著减小.在电极电位(vs.Li/Li⁺) 0.2～0.05V区间,扩散系数由10^-11cm²/s下降到10^-12cm²/s.     

N80油套管钢钝化膜的光电化学性能

采用电容测试法研究了N80油套管钢在浓度为0.5 mol/L NaHCO3溶液中形成钝化膜的半导体性能,结合Mott-Schottky方程分析了测试频率,成膜电位和C l-浓度对钝化膜半导体性能的影响。电容测试结果表明,钝化膜呈n型半导体特性,Mott-Schottky曲线的斜率随着测试频率的增加、成膜电位的正移和溶液中氯离子浓度的增加而增加,相应地膜内的施主密度减小。光电化学实验结果表明,光电流强度随成膜电位的正移及成膜时间的延长而增加,这主要归功于高电位和长时间下所成的钝化膜具有比较均匀的组成,光激发所成的空位或电子在膜内的迁移率的增加。     

Effect of Sn content on the properties of passive film on PbSn alloy in sulfuric acid solution

The effect of Sn content on properties of anodic film formed on PbSn alloys in sulfuric acid solution was investigated using linear sweeping voltage (LSV), cyclic voltammetry (CV), and a.c. voltammetry (ACV), based on the Mott-Schottky analysis. The results revealed that the addition of Sn into lead alloys can promote the corrosion resistance property and could decrease the impedance of anodic film; these results were more remarkable with enhancing the Sn content. The over potential of oxygen evolution on lead alloys enhanced with the increase of Sn content. The Mott-Schottky analysis indicated that the passive film appeared an n-type semiconductor, and the donor density of passive film increased with increasing Sn content. The increased vacancies in the passive film with Sn content increasing could illustrate this trend.     

Investigation on Electronic Property of Passive Film on Nickel in Bicarbonate/Carbonate Buffer Solution

The electronic properties of passive film formed on nickel in bicarbonate/carbonate buffer solution were studied by electrochemical impedance spectra (EIS) and Mott‐Schottky plot. The film composition was analyzed by X‐ray photoelectron spectroscopy (XPS). The results showed that passive film exhibited p‐type semi‐conductive character, and the acceptor density (N_A) decreased with increasing potential, prolonging time, decreasing temperature, increasing pH value and decreasing chloride/sulfur ions concentration. The transfer resistance and film resistance increased with the above factors changing. XPS results showed that passive film was composed of NiO and a little amount of Ni₂O₃.     

SrRuO3阳极催化剂的制备及对乙醇电催化氧化性能研究

用溶胶凝胶法制备了钙钛矿型氧化物SrRuO₃，热重分析和X射线衍射分别对制备过程和产物进行了分析和表征。采用循环伏安、计时电流和交流阻抗方法测试了所得产物对常温下碱性介质中乙醇电化学氧化的催化性能。循环伏安曲线、计时电流和交流阻抗结果表明：在乙醇溶液中，阳极电流密度明显大于氢氧化钾溶液中的阳极电流密度，并且随着电极中SrRuO₃含量的增加，电流密度也大幅度增加，在乙醇溶液中，SrRuO₃电极的电荷迁移阻抗明显降低。SrRuO₃对乙醇电化学氧化具有良好的催化作用。     

Effects of Samarium on the Properties of the Anodic Pb（Ⅱ） Oxides Film Formed on Pb in Sulfuric Acid Solution

The effects of samarium on the properties of the anodic Pb(II) oxides films formed on lead at 0.9 V (vs. Hg/Hg₂SO₄) in 4.5 mol/L H₂SO₄ solution were studied using linear sweep voltammetry (LSV), electrochemical impedance spectroscopy (EIS) and scanning electron micrographs (SEM). The experimental results show that adding Sm to lead metal can inhibit the growth of the Pb(II) oxides film effectively, and reduce the resistance of the PbO oxides film obviously. The addition of Sm increases the porosity of the anodic film, which may cause the increase of the ionic conductance produced by the interstitial liquid among the PbO particles in the film and lead to the decrease of the resistance of the anodic film.     

Electronic Properties of Passive Films Formed on G3 and G30 Nickel-based Alloys in Bicarbonate/Carbonate Buffer Solution

The electronic properties of passive films formed on G3 and G30 alloys in bicarbonate/carbonate buffer solution were comparatively studied by electrochemical impedance spectra(EIS) and Mott-Schottky analysis, the chemical composition of the passive film formed on G3 alloy was detected by X-ray photoelectron spectroscopy (XPS). The results show that passive film on G3 alloy had better protection than that on G30 alloy. The transfer resistance, film resistance and diffusion resistance of the passive films on ...     

Application of electrochemical impedance spectroscopy for characterisation of the reduction of benzophenone in acetonitrile solutions

In this study, the reduction of benzophenone (Bzph) Ph₂C=O (Ph: phenyl group) on glassy-carbon electrode was studied in acetonitrile by means of cyclic voltammetry and electrochemical impedance spectroscopy (EIS). Bzph undergoes two one-electron reductions. The first reduction leads to the formation of radical anion [Ph₂·–O]^? and appears to be reversible and diffusion controlled. The second reduction results in the generation of benzhydrol dianion [Ph₂C–O]^2? and seems to be irreversible. A third quasi-reversible wave observable at more anodic potentials can be ascribed to benzhydrol free radical [Ph₂CH–O] and benzydrol anion [Ph₂CH–O]^? redox couple. The EIS spectra demonstrate that the first reversible reduction of Bzph is characterised by the lowest charge transfer resistance while the resistance for the irreversible reduction is significantly greater. The electrochemical behaviour of Bzph on film consisting of multi-walled carbon nanotubes seems to be different. Thus, the findings reveal slower electrode kinetics which can be associated with electrode passivation.     

Electrochemical Study of Schiff Bases by Means of Self‐Assembled Monolayers

In this paper, Schiffbases were investigated using cyclic voltammetry (CV) and impedance electrochemical spectroscopy (EIS) techniques by means of self‐assembled monolayers for the first time, where a 0.1 M KCl solution and the redox couple of Fe(CN)₆^3?/Fe(CN)₆^4?were used as the electrolyte and probing‐pin, respectively. The monolayers formed by the employed Schiff base were proved to be relatively stable, and its electrochemical response in the studied system with different pH values was also de scribed clearly with CV and EIS plots. The results show that the monolayer of Schiff bases could exist in the solution with pH value from 2 to 10. In the EIS measurement in the concentration range from 10^?5 M to 5× 10^?4 M, a nearly linear relation ship between the charge transfer resistance (R_ct) and the logarithm concentration of Cu²+was observed, suggesting that Cu²+ could be titrated with the EIS method quasi‐quantitatively. The phenomenon agreed with the former report very well. Using the self‐assembled monolayers to study Schiff bases with the electrochemical method is the major contribution of our work.     

Influence of Cr on the Electronic Properties of Passive Film on B30 Alloy in NaOH Solution

The influence of Cr on the electronic properties of the passive film on B30 alloy in NaOH solution was studied via electrochemical impedance spectra(EIS), potentiodynamic curve and Mott-Schottky plot. The Cr doped in the passive film on B30 alloy was detected by X-ray photoelectron spectroscopy(XPS). XPS results show that Cr₂O₃ appeared on the passive film, which implied the enhanced anti-corrosion of B30 alloy. The passive film showed a p-type semi-conductive character. The acceptor density(N_A) was in an order of magnitude of 10²² cm^-3, and N_A decreased with the increment of Cr. EIS results show that the film resistance(R_f) increased with increasing the amount of Cr. The diffusion coefficient(D₀) was calculated to be in a range of 10^-16-10^-17 cm^-2/s on the basement of point defect model(PDM).