Thermal,mechanical and morphological analysis of poly(ε‐caprolactone), cellulose acetate and their blends

Poly(ε‐caprolactone) (PCL), cellulose acetate (CA) and their blends were characterized by their tensile strength, differential scanning calorimetry (DSC) and optical microscopy (OM). The compatibility of the blends was investigated and the OM results showed that CA tended to disperse as discrete particles in PCL. Thermal analysis showed the characteristic melting temperature peaks for PCL and CA in all blends, indicating that the compounds were immiscible. The addition of CA to PCL increased slightly the crystallinity of PCL, decreased the elongation at yield and the tensile strength up to 40/60 PCL/CA (w/w), which suggested incompatibility between the polymers. Together, these results indicate the absence of a strong chemical interaction between the two polymers. In agreement with this, the addition of CA to blends with PCL increased Young's modulus. Copyright © 2003 John Wiley & Sons, Ltd.     

Fabrication of Single Wall Carbon Nanotubes-Based Poly(vinyl butyral) Nanocomposites with Enhanced Mechanical and Thermal Properties

In this research, poly(vinyl butyral) (PVB)/single wall carbon nanotubes (SWCNT) composites were prepared via solution blending method. Dispersion degree of SWCNT in the composites was characterized by Scanning Electron Microscopy (SEM) and mechanical properties were measured with tensile testing. Thermal degradation of composites was investigated using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). SEM analysis confirmed good dispersion of the nanotubes in the PVB. The tensile tests showed significant increases in mechanical properties such as exceptional improvement in tensile strength, Young's modulus and flexibility for the composites compared to PVB at low SWCNT content.The TGA curves indicated that adding SWCNT improved the thermal stability of the PVB significantly and the degradation of the polymer matrix shifted to the higher temperatures. For the sample containing 0.6 wt%, an increase of 171% in modulus and a 258.4% enhancement of tensile strength were achieved. Also, elongation at break increased 28.7% at this loading. In fact, intrinsic properties of nanotubes caused enhancement of strength and flexibility simultaneously. Also, for this composite, T_onset and T_max enhanced remarkably and weight loss reduced greatly and residue at 600°C increased to high values. These results are promising for application of the PVB in industry.     

Effects of the compatibilizer PE‐g‐GMA on the mechanical,thermal and morphological properties of virgin and reprocessed LDPE/corn starch blends

The effects of the compatibilizer polyethylene grafted with glycidyl methacrylate (PE‐g‐GMA) on the properties of low‐density polyethylene (LDPE) (virgin and reprocessed)/corn starch blends were studied. LDPE (virgin and reprocessed)/corn starch blends containing 30, 40 and 50 wt% starch, with or without compatibilizer, were prepared by extrusion and characterized by the melt flow index (MFI), tensile test, dynamic mechanical analysis (DMTA) and light microscopy. The addition of starch to LDPE reduced the MFI values, the tensile strength and the elongation at break, whereas the modulus increased. The decreases in the MFI and tensile properties were most evident when 40 and 50 wt% starch were added. Blends containing 3 wt% PE‐g‐GMA had higher tensile strength values and lower MFI values than blends without compatibilizer. Light microscopy showed that increasing the starch content resulted in a continuous phase of starch. Copyright © 2005 John Wiley & Sons, Ltd.     

Electrospun poly(ε‐caprolactone)‐based composites using synthesized β‐tricalcium phosphate

Non‐woven hybrid membranes based on poly(ε‐caprolactone) (PCL) and as‐synthesized β‐tricalcium phosphate (β‐TCP) were obtained by the electrospinning technique. A wide range of composition was investigated, the filler content spanning between 2 and 60 wt%. The synthesis of the β‐TCP powder was accomplished by titration of calcium hydroxide with phosphoric acid followed by calcination of the resulting precipitate at 1100°C. The as‐dried calcium phosphate was characterized by Inductive Coupled Plasma (AES‐ICP), thermal analysis (TG‐DTA), Fourier Transform Infrared Spectroscopy (FT‐IR), Scanning Electron Microscopy (SEM), and high temperature X‐ray diffraction analysis (HT‐XRD). The specific surface area (SSA) was evaluated by N₂ adsorption. Microstructure of PCL/TCP membranes was investigated by SEM, energy dispersion spectroscopy (EDS), XRD analysis, and SSA measurements. The average fiber diameter ranged between 1 and 2 µm, the porosity was 80–90%, and the SSA 16 m²/g. Mechanical properties were determined by uniaxial tensile test. A remarkable enhancement of the tensile modulus was observed for composites containing up to 4 wt% β‐TCP. The ultimate tensile strength ranged between 2 and 3 MPa for samples loaded up to 8 wt%. For most of the samples, the elongation at break was in the range 100–150%. Copyright © 2010 John Wiley & Sons, Ltd.     

Physico-Mechanical Properties of Biodegradable Rubber Toughened Polymers

Summary: In this study, blends of poly(lactic acid) (PLA) with poly(butylene adipate-co-terephthalate) (PBAT) were studied for their mechanical and thermal properties as a function of the PBAT content. Tensile testing, impact testing, differential scanning calorimetry (DSC), dynamic mechanical analysis (DMTA) and scanning electron microscopy (SEM) were used to characterize the blends. It was observed that PLA/PBAT blends maintained quite high modulus and tensile strength compared to pure PLA. Small amounts of PBAT improved the elongation at break and the impact resistance showing a debonding effect typical of rubber toughened systems.     

环氧丁羟型聚氨酯弹性体的制备与性能

以间氯过氧苯甲酸(mCPBA)为氧化剂对降解法制备的端羟基聚丁二烯(DHTPB)中的部分双键进行环氧化改性,通过控制mCPBA和双键的比例制得具有不同环氧率的环氧化端羟基聚丁二烯(EHTPB),经1H-NMR分析测试表明EHTPB的环氧率分别为5%、10%和15%,与设计值基本一致.进一步以EHTPB为多元醇、4,4'-二苯基甲烷二异氰酸酯(MDI)为异氰酸酯、1,4-丁二醇为扩链剂制备了环氧丁羟型聚氨酯弹性体(EPU),并对其性能进行了测试,研究结果表明:丁羟胶的环氧化改性对聚氨酯弹性体的力学性有着一定的提升作用,其杨氏模量和拉伸强度随环氧率的上升而提高,而断裂伸长率则随环氧率的上升有所下降;环氧丁羟型聚氨酯弹性具有优异的弹性恢复能力;环氧化改性后,聚氨酯弹性体的热稳定性有一定程度的提高;聚氨酯弹性体的玻璃化转变温度随环氧率的上升而升高.     

Mechanical and viscoelastic properties of chitin fiber reinforced poly(ε-caprolactone)

Poly(ε-caprolactone)/chitin fiber (PCL-CF) composites as potential bone substitutes were prepared using a simple melt-processing method. The results from differential scanning calorimetry and dynamic mechanical thermal analysis (DMTA) showed that there was interaction between PCL and CF. Static mechanical testing showed that tensile strength, Young’s modulus and flexural strength were increased by the addition of CF. The measurements from DMTA and an advanced rheometric expansion system showed that both the storage modulus and loss modulus were enhanced by CF. The PCL-CF composite with CF of 45% by mass had the best properties among all the tested composites.     

Preparation and cryogenic mechanical properties of epoxy resins modified by poly(ethersulfone)

A thermoplastic, poly(ethersulfone) (PES) was used to modify a bisphenol‐F based epoxy resin cured with an aromatic diamine. The initial mixtures before curing, prepared by melt mixing, were homogeneous. Scanning electron microscopy (SEM) micrographs of solvent‐etched fracture surfaces of the cured blends indicated that phase separation occurred after curing. The cryogenic mechanical behaviors of the epoxy resins were studied in terms of tensile properties and Charpy impact strength at cryogenic temperature (77 K) and compared to their corresponding behaviors at room temperature (RT). The addition of PES generally improved the tensile strength, elongation at break, and impact strength at both RT and 77 K except the RT tensile strength at 25 phr PES content. It was interesting to observe that and the maximum values of the tensile strength, elongation at break, and impact strength occurred at 20 phr PES content where a co‐continuous phase formed. Young's modulus decreased slightly with the increase of the PES content. Moreover, the tensile strength and Young's modulus at 77 K were higher than those at RT at the same composition, whereas the elongation at break and impact strength showed the opposite results. Finally, the differential scanning calorimetry analysis showed that the glass transition temperature (T_g) was enhanced by the addition of PES. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 612–624, 2008     

Synthesis and characterization of compatibilized poly(ϵ‐caprolactone)/granular starch composites

To improve the mechanical properties of granular corn starch‐filled poly(ϵ‐caprolactone) (PCL) compositions, three strategies were investigated including the hydrophobic coating of starch granules by reaction with n‐butyl isocyanate, the addition of PCL‐grafted dextran (PGD) as an amphiphilic compatibilizer, and the use of PCL‐grafted granular starch (PGS). Except for the chemical modification of granular starch by reaction with n‐butyl isocyanate, the synthesis of both PGD and PGS relies upon the controlled ring‐opening polymerization (ROP) of ϵ‐caprolactone (CL) initiated by Al‐alkoxides generated onto the polysaccharide, either dextran or starch particles. While the hydrophobic coating of starch only provides higher tensile strength and elongation at break, these properties as well as Young's modulus and strength at yield of the PCL/starch blends were remarkably increased by locating the PCL‐grafted dextran at the filler/matrix interface. It is however worth pointing out that a tougher and stiffer material was obtained by melt blending PGS and pure PCL. These property changes were analyzed and clearly related to parameters such as filler dispersion, interfacial tension, interfacial adhesion and reinforcement by PCL crystallites.     

The electrospun poly(ε‐caprolactone)/fluoridated hydroxyapatite nanocomposite for bone tissue engineering

Biodegradable cell‐incorporated scaffolds can guide the regeneration process of bone defects such as physiological resorption, tooth loss, and trauma which medically, socially, and economically hurt patients. Here, 0, 5, 10, and 15 wt% fluoridated hydroxyapatite (FHA) nanoparticles containing 25 wt% F^? and 75 wt% OH^? were incorporated into poly(ε‐caprolactone) (PCL) matrix to produce PCL/FHA nanocomposite scaffolds using electrospinning method. Then, scanning electron microscopy (SEM), X‐ray diffraction (XRD) pattern, and Fourier transform infrared spectroscopy (FTIR) were used to evaluate the morphology, phase structure, and functional groups of prepared electrospun scaffolds, respectively. Furthermore, the tensile strength and elastic modulus of electrospun scaffolds were investigated using the tensile test. Moreover, the biodegradation behavior of electrospun PCL/FHA scaffolds was studied by the evaluation of weight loss of mats and the alternation of pH in phosphate buffer saline (PBS) up to 30 days of incubation. Then, the biocompatibility of prepared mats was investigated by culturing MG‐63 osteoblast cell line and performing MTT assay. In addition, the adhesion of osteoblast cells on prepared electrospun scaffolds was studied using their SEM images. Results revealed that the fiber diameter of prepared electrospun PCL/FHA scaffolds alters between 700 and 900 nm. The mechanical assay illustrated the mat with 10 wt% FHA nanoparticles revealed the highest tensile strength and elastic modulus. The weight loss alternation of mats determined around 1% to 8% after 30 days of incubation. The biocompatibility and cell adhesion of mats improved by increasing the amounts of FHA nanoparticles.     

Effect of surface modification of colloidal silica nanoparticles on the rigid amorphous fraction and mechanical properties of amorphous polyurethane–urea–silica nanocomposites

Colloidal silica nanoparticles (NPs) modified with eight different silane coupling agents were incorporated into an amorphous poly(tetramethylene oxide)‐based polyurethane–urea copolymer matrix at a concentration of 10 wt % (4.4 vol %) in order to investigate the effect of their surface chemistry on the structure–property behavior of the resulting nanocomposites. The rigid amorphous fraction (RAF) of the nanocomposite matrix as determined by differential scanning calorimetry and dynamic mechanical analysis was confirmed to vary significantly with the surface chemistry of the NPs and to be strongly correlated with the bulk mechanical properties in simple tension. Hence, nanocomposites with an RAF of about 30 wt % showed a 120% increase in Young's modulus, a 25% increase in tensile strength, a 15% decrease in elongation at break with respect to the neat matrix, which had no detectable RAF, whereas nanocomposites with an RAF of less than 5% showed a 60% increase in Young's modulus, a 10% increase in tensile strength and a 5% decrease in the elongation at break. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2543–2556     

Effect of Zinc Oxide on Morphology and Mechanical Properties of Polyoxymethylene/Zinc Oxide Composites

This paper studies the effects of zinc oxide (ZnO) on morphology and mechanical properties of pure polyoxymethylene (POM) and POM/ZnO composites. POM/ZnO composites with varying concentration of ZnO were prepared by melt mixing technique in a twin screw extruder. The dispersion of ZnO particles on POM composites was studied by scanning electron microscope (SEM). It is observed that the dispersion of ZnO particles is relatively good. The mechanical properties of the composites such as tensile strength, stress at break, Young's modulus and impact strength were measured. Increasing content of ZnO up to 4.0 wt% increases the impact strength of POM. Addition of ZnO beyond 4.0 wt% decreases the impact strength. The composites containing ZnO content greater than 2.0 wt% show increased Young's Modulus. The tensile strength and stress at break decrease with increasing ZnO content. This may be due to the compatibility between ZnO and POM.     

Biocomposites based on Alfa fibers and starch‐based biopolymer

Biocomposite materials based on Alfa cellulose fibers (esparto grass plant) as reinforcing element and starch‐based biopolymer matrix were prepared and characterized in terms of mechanical performance, thermal properties, and water absorbance behavior. The fibers and the matrix were first mixed in the melted state under mechanical shearing using a plastograph and the obtained composites were molded by injection process. The tensile mechanical analysis showed a linear increase of the composite flexural and tensile modulus upon increasing the fiber content, together with a sharp decrease of the elongation at break. The fibers′ incorporation into the biopolymer matrix brings about an enhancement in the mechanical strength and the impact strength of the composite. Dynamic mechanical thermal analysis (DMTA) investigation showed two relaxations occurring at about ?30 and 35°C. The addition of Alfa fibers enhanced the storage modulus E′ before and after T_α, which is consistent with the reinforcing effect of Alfa cellulose fibers. Copyright © 2008 John Wiley & Sons, Ltd.     

Zein supports scaffolding capacity toward mammalian cells and bactericidal and antiadhesive properties on poly(ε-caprolactone)/zein electrospun fibers

Studies investigate the electrospinnability of poly(ε-caprolactone)/protein blends to produce fibers for tissue engineering applications. However, no reports show that zein can improve the scaffolding capacity toward stem cells and promote antiadhesive and bactericidal properties to the poly(ε-caprolactone)/zein fibers. We create fibers with average diameters ranging from 200 to 400 nm from the electrospinning of poly(ε-caprolactone)/protein mixtures. Poly(ε-caprolactone)/zein blends are electrospinnable at zein concentration between 20 and 40 wt% in a 70/30 formic acid/acetic acid mixture. Water contact angle measurements indicate that zein increases fiber hydrophilicity. The water contact angle decreases from 118° (pure poly(ε-caprolactone) fiber) to 73° for the scaffold containing 40 wt% zein. The zein (40 wt%) significantly increases Young's modulus from 260 MPa (pure poly(ε-caprolactone) fibers) to 980 MPa (poly(ε-caprolactone)/zein fibers) with no substantial influence on elongation at break (ε ≥ 125%) and tensile strength (≥0.040 MPa). The electrospun scaffolds containing zein also promote cell adhesion, proliferation, and spreading of adipose-derived human mesenchymal stem cells for at least 7 days of culture. The zein on poly(ε-caprolactone)/zein fibers can prevent the attachment and proliferation of Escherichia coli and Staphylococcus aureus. We propose these materials for wound healing and skin repair.     

Structure–property co‐relationship of fluorinated poly(imide‐siloxane)s

Eight poly(imide‐siloxane)s co‐polymers have been prepared by one pot solution imidization method. The polymers are synthesized by the reaction of bisphenol‐A‐dianhydride (BPADA) with fluorinated diamine 4,4′‐bis(3″‐trifluoromethyl‐p‐aminobiphenyl ether) biphenyl, and aminopropyl‐terminated polydimethylsiloxane (APPS). The polymers are synthesized by varying the siloxane loading to 5, 10, 15, 20, 25, 30, 35, and 40 wt%, respectively. Thermal, mechanical, rheological, and dielectric properties of these polymers have been evaluated with respect to siloxane loading. The polymers showed glass transition temperature of 107–203°C and tensile strength at break of 24–75 MPa depending on siloxane loading. The elongation break of the polymers ranges from 24 to 144% depending on siloxane loading. The amounts of char residue in the polymers have been correlated with incorporated siloxane in the polymer by NMR techniques. The polymers showed very low water absorption and dielectric constant as low as 2.43 when the siloxane loading is 40 wt%. Copyright © 2008 John Wiley & Sons, Ltd.     

Fabrication of open‐porous PCL/PLA tissue engineering scaffolds and the relationship of foaming process,morphology, and mechanical behavior

Tissue engineering scaffolds should provide a suitable porous structure and proper mechanical strength, which is beneficial for the delivery of growth factor and regulation of cells. In this study, the open‐porous polycaprolactone (PCL)/poly (lactic acid) (PLA) tissue engineering scaffolds with suitable porous scale were fabricated using different ratios of PCL/PLA blends. At the same time, the relationship of foaming process, morphology, and mechanical behavior in the optimized batch microcellular foaming process were studied based on the single‐factor experiment method. The porous structures and mechanical strength of the scaffolds were optimized by adjusting foaming parameters, including the temperature, pressure, and CO₂ dissolution time. The results indicated that the foaming parameters influence the cell morphology, further determine the mechanical behavior of PCL/PLA blends. When the PCL content is high, with the increase of temperature and time, the cell diameter and the elastic modulus increased, and the tensile strength and elastic modulus increased with the increase of the average cell size, and decreased as the increase of the cell density. While when the PLA content was high, the cell diameter showed the same trend, and the tensile strength and elastic modulus were higher, and the elongation at break was lower, and tensile strength and elastic modulus decreased with the increase of the average cell size and increased with the increase of cell density. This work successfully fabricated optimized porous PCL/PLA scaffolds with excellent suitable mechanical properties, pore sizes, and high interconnectivity, indicating the effectiveness of modulating the batch foaming process parameters.     

Biodegradable polyester/modified mesoporous silica composites for effective bone repair with self‐reinforced properties

A series novel composites based on poly(_L‐lactide) (PLLA) oligomer modified mesoporous silica (MCM41) homogeneous dispersed into poly(_L‐lactide‐co‐trimethylene carbonate‐co‐glycolide) (PLTG) terpolymer has been successfully prepared. The structure of PLTG terpolymer was characterized by ¹H NMR. The structure and properties of modified and unmodified MCM41 were attested by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analyzer (TGA), X‐ray diffraction (XRD), N₂ adsorption–desorption, scanning electron microscope (SEM), and transmission electron microscope (TEM), which demonstrated that the MCM41 was successfully grafted by the PLLA oligomer. The effect of different concentration of modified MCM41 in PLTG matrix on thermal properties, mechanical properties, and hydrophilicity was investigated by TGA, differential scanning calorimetry (DSC), mechanical testing, contact angle measurement, and SEM. The results of mechanical tests showed that 5 wt% of modified MCM41 nanoparticles gave rise to optimal reinforcing effect. The tensile strength, Young's modulus, and elongation at break of the PLTG/PLLA‐MCM41 (5%) composites were 33.2 Mpa, 1.58 Gpa, and 268.7%, respectively, which were all higher than the PLTG/MCM41 (5%) composites and pristine PLTG matrix, which were due to good interfacial adhesion between the PLTG matrix and MCM41 nanoparticles. TGA and DSC have shown that 5% modified MCM41 in the PLTG increased the temperature of composite degradation and T_g. Water contact angle measurement showed the hydrophilicity of the composites increases with the increase of modified MCM41 content. The live/dead assay showed that the modified MCM41 existing on the PLTG matrix presents very excellent cytocompatibility. Therefore, the novel composite material represents promising way for bone tissue engineering application.     

Bio-Based Nanocomposites of Cellulose Acetate and Nano-Clay with Superior Mechanical Properties

Summary: Bio-based nanocomposites were manufactured by melt intercalation of nanoclays and cellulose acetate (CA) with and without plasticizer. Glycerol triacetate (triacetin) as plasticizer up to 30 mass%, and different types of organo-modified and unmodified montmorillonites (MMTs) as filler were used. X-ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM), were used to study clay dispersion, intercalation/exfoliation, and structure of the composites. XRD and TEM revealed very good dispersion and exfoliation of modified clay throughout the CA matrix. While for unmodified clay agglomeration and poor dispersion but an intercalated structure was observed. The mechanical properties of injection moulded test bars were determined by a tensile experiment giving tensile strength, Young's modulus and elongation at break. Adding plasticizer facilitated the processing and up to 20 mass%, increased the tensile strength, Young's modulus and elongation at break as well. Higher amount of plasticizer diminished the tensile properties except elongation showing a slight increase. In all plasticized composites, organo-modified clay improved the tensile strength and at the same time, young's modulus and elongation almost remained constant. On the other hand, plasticized CA compounded with unmodified clay revealed lower properties. In a particular case, compounding of unplasticized CA with unmodified clay resulted in superior mechanical properties with a novel structure. So that, in optimum percentage –5 mass%- of unmodified clay, tensile strength and young's modulus increased significantly by 335% and 100%, to 178 MPa and 8.4 GPa, respectively. This is a dramatic improvement in strength and stiffness of CA. Adding organo-modified clay resulted in a little improvement in tensile properties. SEM pictures of the optimum composite showed a core/shell structure with high orientation in the shell part. It is supposed that this behaviour is caused by the interaction between CA hydroxyl groups and free cations existing in the galleries of unmodified clay.     

动态固化聚丙烯/环氧树脂共混物的研究

将动态硫化技术应用于热塑性树脂 热固性树脂体系 ,制备了动态固化聚丙烯 (PP) 环氧树脂共混物 .研究了动态固化PP 环氧树脂共混物中两组分的相容性、力学性能、热性能和动态力学性能 .实验结果表明 ,马来酸酐接枝的聚丙烯 (PP g MAH)作为PP和环氧树脂体系的增容剂 ,使分散相环氧树脂颗粒变细 ,增加了两组分的界面作用力 ,改善了共混物的力学性能 .与PP相比 ,动态固化PP 环氧树脂共混物具有较高的强度和模量 ,含 5 %环氧树脂的共混物拉伸强度和弯曲模量分别提高了 30 %和 5 0 % ,冲击强度增加了 15 % ,但断裂伸长率却明显降低 .继续增加环氧树脂的含量 ,共混物的拉伸强度和弯曲模量增加缓慢 ,冲击强度无明显变化 ,断裂伸长率进一步降低 .动态力学性能分析 (DMTA)表明动态固化PP 环氧树脂共混物是两相结构 ,具有较高的储能模量 (E′)     

Mechanical and dynamic viscoelastic properties of hydroxyapatite reinforced poly(ε-caprolactone)

Poly(ε-caprolactone)/hydroxyapatite (PCL/HA) composites as potential bone substitutes were prepared by melt-blending. The melting, crystallization and glass transition temperatures deduced from differential scanning calorimetery and dynamic mechanical thermal analysis (DMTA) were all changed by the addition of HA, suggesting an interaction at the interface of these two phases. Quasi-static mechanical testing shows that the yield strength and Young's modulus of PCL were increased by the addition of the reinforcement filler, HA. Dynamic viscoelastic properties were investigated using DMTA and an advanced rheometric expansion system. The results show that both the storage modulus and viscous modulus are enhanced by HA, and the PCL composite melts still behave like pseudo-plastic liquid.