Mechanical and thermal properties of natural rubber-modified poly(lactic acid) compatibilized with telechelic liquid natural rubber

The effect of telechelic liquid natural rubber (TLNR) compatibilizer on natural rubber (NR) modified by melt-blending with poly(lactic acid) (PLA-NR) is studied using infrared spectroscopy (FTIR), differential scanning calorimetry (DSC) and notched Izod impact testing to determine the structural, thermal and mechanical properties. Scanning electron microscopy (SEM) is used to relate these properties to the morphology of the blends and fracture surface of the impact samples. Through this, it is revealed that the addition of LNR significantly improves the tensile and impact strength of PLA-NR, with the greatest compatibilization effect achieved with 6 wt% LNR. This improvement is confirmed through FTIR analysis to be due to a chemical interaction between LNR and PLA that improves the phase morphology of the blend.     

Barrier,Mechanical, Morphological and Thermal Properties of Compatibilized High Density Polyethylene and Polyamide 6 Blends

Effectiveness of the content of maleic anhydride (MAH) and polyamide 6 (PA6) on mechanical, thermal, barrier (moisture and oxygen) properties of HDPE/PA6 blends was investigated. Blends of HDPE with PA6 were prepared by in situ method. Molau test and FTIR spectroscopy results confirmed the reactive compatibilization through grafting of MAH on HDPE and PA6 chains in PA6/HDPE blends. Low concentration of benzoyl peroxide (BPO) and MAH reduced the particle size, improved phase morphology and mechanical properties of PA6/HDPE blends. Decrease in mechanical properties of PA6/HDPE blends was observed at high concentration of BPO and MAH.     

Effects of Epoxidation Content of ENR on Morphology and Mechanical Properties of Natural Rubber Blended PVC

This research work has concerned a study on toughness of PVC/natural rubber (NR) blends compatibilized with epoxidized natural rubber (ENR). The aim of this work was to investigate the effect of degree of epoxidation on morphology and mechanical properties of the blends. Epoxidized natural rubber with a variety of epoxidation contents were prepared by reacting the NR latex with formic acid and hydrogen peroxide at various chemical contents. Chemical structure and epoxidation content of epoxidized natural rubber were evaluated by FTIR and ¹H-NMR techniques. After that, three grades of ENR with epoxidation contents of 15, 25 and 42 % (by mole) were further used for blending with PVC and NR in an internal mixer at 60 rpm and at 170 °C. From tensile and impact tests, it was found that tensile elongation and impact strength of the materials remarkably increased with degree of epoxidation. On the other hand, tensile strength and modulus of the materials rarely changed with the epoxidation content. An increase in toughness of the blends with epoxidation content was related to a better molecular interaction between PVC and ENR as suggested by torque-time curves of the materials.     

Reinforcement of compatibilized NR/NBR blends by fly ash particles and precipitated silica

Effects of precipitated silica (PSi) and silica from fly ash (FA) particles (FASi) on the cure and mechanical properties before and after thermal and oil aging of natural rubber (NR) and acrylonitrile–butadiene rubber (NBR) blends with and without chloroprene rubber (CR) or epoxidized NR (ENR) as a compatibilizer have been reported in this paper. The experimental results suggested that the scorch and cure times decreased with the addition of silica and the compound viscosity increased on increasing the silica content. The mechanical properties for PSi filled NR/NBR vulcanizates were greater than those for FASi filled NR/NBR vulcanizates in all cases. The PSi could be used for reinforcing the NR/NBR vulcanizates while the silica from FA was regarded as a semi‐reinforcing and/or extending filler. The incorporation of CR or ENR enhanced the mechanical properties of the NR/NBR vulcanizates, the ENR being more effective and compatible with the blend. The mechanical properties of the NR/NBR vulcanizates were improved by post‐curing effect from thermal aging but deteriorated by the oil aging. Copyright © 2008 John Wiley & Sons, Ltd.     

Effect of sol–gel derived in situ silica on the morphology and mechanical behavior of natural rubber and acrylonitrile butadiene rubber blends

Silica particles were generated and grown in situ by sol–gel method into rubber blends comprised of natural rubber (NR) and acrylonitrile butadiene rubber (NBR) at various blend ratios. Silica formed into rubber matrix was amorphous in nature. Amount of in situ silica increased with increase in natural rubber proportion in the blends during the sol–gel process. Morphology studies showed that the generated in situ silica were nanoparticles of different shapes and sizes mostly grown into the NR phase of the blends. In situ silica filled NR/NBR blend composites showed improvement in the mechanical and dynamic mechanical behaviors in comparison to those of the unfilled and externally filled NR/NBR blend composites. For the NR/NBR blend at 40/60 composition, in particular, the improvement was appreciable where size and dispersion of the silica particles into the rubber matrix were found to be more uniform. Dynamic mechanical analysis revealed a strong rubber–in situ silica interaction as indicated by a positive shift of the glass transition temperature of both the rubber phases in the blends.     

Compatibilization of elastomer-based blends

The reactive compatibilization of ethylene-propylene-diene (EPDM)-based dissimilar elastomer blends has been investigated in terms of mechanical properties and swelling degree. The use of mercapto-functionalized copolymers resulted in an improvement of mechanical properties of natural rubber-EPDM blends. The mercapto-groups are able to react with the carbon-carbon double bonds of the high diene rubber, resulting in a good interaction between phases. These interactions were confirmed by the amount of insoluble material obtained in non-vulcanized blends. From dynamic mechanical properties and swelling degree, one can suggest a covulcanization process in these blends cured with sulfur-based system. Blends composed by nitrile rubber with EPDM displayed good results in terms of mechanical properties when mercapto-functionalized EVA was employed instead of functionalized EPDM, probably because of the higher polarity of the former associated to its lower viscosity. Additionally, an improvement on mechanical properties was also achieved by using EPDM functionalized with mercapto or anhydride groups in combination with nitrile rubber functionalized with epoxy or oxazoline groups.     

Dynamic mechanical properties of isotactic polypropylene/nitrile rubber blends: Effects of blend ratio,reactive compatibilization,and dynamic vulcanization

The effect of blend ratio and compatibilization on dynamic mechanical properties of PP/NBR blends was investigated at different temperatures. The storage modulus of the blend decreased with increase in rubber content and shows two T_g's indicating the incompatibility of the system. Various composite models have been used to predict the experimental viscoelastic data. The Takayanagi model fit well with the experimental values. The addition of phenolic modified polypropylene (Ph-PP) and maleic modified polypropylene (MA-PP) improved the storage modulus of the blend at lower temperatures. The enhancement in storage modulus was correlated with the change in domain size of dispersed NBR particles. The effect of dynamic vulcanization using sulfur, peroxide, and mixed system on viscoelastic behavior was also studied. Among these peroxide system shows the highest modulus. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 2309–2327, 1997     

Interfacial reciprocal grafting by free radical reactions in polymer blends

Recent developments in the field of reactive compatibilization of polymer blends prepared by melt processing focus on the addition of low molecular weight compounds. This work deals with in situ compatibilization through the formation of graft or crosslinked copolymers at the interface. Mixtures of semicrystalline hydrocarbon polymers have been subjected to free radical reactivity, in a co-rotating twin screw extruder (ZSK 30) in a single step. The particular system, high density polyethylene and polyamide 6, was blended in the presence of a peroxide and a reactive bifunctional monomer, maleic anhydride. Because of a combined effect, the reaction appears to occur mainly at the interface, where the resulting grafted copolymer acts as an anchor for the final stabilization of the biphasic system. Different analytical techniques, such as differential scanning calorimetry, scanning electron microscopy and tensile testing, helped in characterizing the resulting blends and confirmed the high level of interfacial grafting and the expected improvement in mechanical properties.     

Blending of Natural Rubber/Recycled Ethylene-Propylene-diene Rubber: Promoting the Interfacial Adhesion Between Phases by Natural Rubber Latex

This article deals with blends based on natural rubber (NR) and recycled ethylene-propylene-diene rubber (R-EPDM). Natural rubber latex (NRL) was introduced into the blends to enhance interfacial adhesion between NR and R-EPDM. A new route of compounding was also suggested. The blends were prepared by mixing R-EPDM and other additives in NRL before blending with natural rubber on a two-roll mill. By applying this method, the homogeneity of the blends and cross-linking distribution are significantly improved. The blends exhibited superior state of cure, swelling resistance, mechanical properties and dynamic mechanical properties. The degree of entanglement between NR and R-EPDM also increased after NRL modification.     

Thermal properties of compatibilized and filled natural rubber/acrylonitrile butadiene rubber blends

The thermal behaviour of natural rubber/acrylonitrile butadiene rubber (NR/NBR) was studied using thermogravimetry (TG) and differential scanning calorimetry (DSC) in terms of blend ratio, crosslinking systems, fillers and compatibilizer (neoprene) were analyzed. The presence of NBR markedly increases the thermal stability of their blends and it lies in between NR and NBR. DSC studies revealed the thermodynamic immiscibility of the NR/NBR blends by the presence of two distinct glass transition temperatures and the immiscibility was prominent even in the presence of a compatibilizer.     

From incompatible poly(aryl ether sulfone)/polyamide 4.6. blends to new impact resistant alloys by a synergistic combination of a block copolymer emulsifier and an impact modifier

The compatibilization and impact modification of blends of a relatively new engineering plastic polyamide 4.6 (PA 4.6) and a poly(aryl ether sulfone) (PSU) are investigated. PSU-b-PA6 block copolymers, which can be easily synthesized by ring opening polymerization of ϵ-caprolactam in the presence of a commercial PSU, were found to be very efficient emulsifiers for these incompatible blends. Small amounts (1–4%) of copolymer are sufficient to significantly reduce the particle size and to improve the tensile and impact properties. Combinations of the copolymer and an impact modifier (ethylene-propylene rubber grafted with maleic anhydride) are synergistic and high impact PSU/PA 4.6 alloys are obtained in that way.     

Reactive Compatibilization of Polyethylene/Ground Tire Rubber Inhomogeneous Blends via Interactions of Pre-Functionalized Polymers in Interface

Summary: Reactive compatibilization of recycled low- or high-density polyethylenes (LDPE and HDPE, respectively) and ground tire rubber (GTR) via chemical interactions of pre-functionalized components in their blend interface has been carried out. Polyethylene component was functionalized with maleic anhydride (MAH) as well as the rubber component was modified via functionalization with MAH or acrylamide (AAm) using chemically or irradiation (γ-rays) induced grafting techniques. The grafting degree and molecular mass distribution of the functionalized polymers have been measured via FTIR and Size Exclusion Chromatography (SEC) analyses, respectively. Thermoplastic elastomer (TPE) materials based on synthesized reactive polyethylenes and GTR as well as ethylene-propylene-diene rubber, EPDM were prepared by dynamic vulcanization of the rubber phase inside thermoplastic (polyethylene) matrix and their phase structure, and main properties have been studied using DSC and mechanical testing. As a final result, the high performance TPE with improved mechanical properties have been developed.     

Investigation of phase morphology of incompatible polyethylene/nylon 6 blends containing EPDM-based functionalized compatibilizers

Graft copolymer and graft terpolymer were prepared by solution grafting of maleic anhydride (MAH) or acrylonitrile (AN) alone and mixture of MAH and AN on to ethylene–propylene–diene terpolymer (EPDM) using benzoyl peroxide (BPO) as an initiator. The resulting EPDM-g-MAH, EPDM-g-AN and EPDM-g-(MAH-co-AN) have been used to obtain a binary blend of Nylon 6/functionalized EPDM and a ternary blend of polyethylene/Nylon 6/functionalized EPDM by melt blending. The effects of the nature and the amount of the grafted species on the phase morphology, crystallization behavior and mechanical properties of the blends were characterized through scanning electron microscopy, optical microscopy, infrared spectroscopy and using a dynamic mechanical analyzer. From the morphological study, it can clearly be seen that the presence of the functionalized EPDMs in these blends resulted in an improvement of the dispersion degree in incompatible polyethylene/Nylon 6 blends.     

Ultra‐high molecular weight styrenic block copolymer/TPU blends for automotive applications: Influence of various compatibilizers

Thermoplastic elastomers (TPEs) based on new generation ultrahigh molecular weight styrene‐ethylene‐butylene‐styrene (SEBS) and thermoplastic polyurethane (TPU) are developed and characterized especially for automotive applications. Influence of maleic anhydride grafted styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MA) and maleic anhydride grafted ethylene propylene rubber (EPM‐g‐MA) as compatibilizers has been explored and compared on the blends of SEBS/TPU (60:40). The amount of compatibilizers was varied from 0 to 10 phr. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) studies revealed the dramatic changes from a nonuniform to finer and uniform dispersed phase morphology. This was reflected in various mechanical properties. SEBS‐g‐MA modified blends showed higher tensile strength. EPM‐g‐MA modified blends also displayed considerable improvement. Elongation at break (EB) was doubled for the entire compatibilized blends. Fourier‐transform infrared spectrometry (FTIR) confirmed the chemical changes in the blends brought about by the interactions between blend components and compatibilizers. Both SEBS‐g‐MA and EPM‐g‐MA had more or less similar effects in dynamic mechanical properties of the blends. Additionally, melt rheological studies have also been pursued through a rubber process analyzer (RPA) to get a better insight.     

Thermoplastic elastomer based on high‐density polyethylene/natural rubber blends: rheological,thermal, and morphological properties

Thermoplastic elastomer (TPE) comprising air‐dried sheet or natural rubber (ADS or NR) and high‐density polyethylene (HDPE) was prepared by a simple blending technique. NR and HDPE were mixed with each type of phenolic compatibilizer (HRJ‐10518 or SP‐1045) or liquid natural rubber (LNR) at 180°C in an internal mixer. The mixing torque, shear stress, and shear viscosity of the blends increased with increasing amounts of NR. Positive deviation blend (PDB) for the blends containing active hydroxyl methyl phenolic resin in HRJ‐10518 or dimethyl phenolic resin in SP‐1045 was obtained. PDB was not observed for the blends without the compatibilizers or with LNR. The blends with HRJ‐10518 or SP‐1045 were compatible or partially compatible while the LNR blends were incompatible. In the phenolic compatibilized blends, NR dispersed in the HDPE matrix was found in the NR/HDPE blends of 20/80, 40/60, and 50/50 ratios. HDPE dispersed in NR matrix was obtained in the NR/HDPE blend of 80/20 ratio, and the co‐continuous phase was accomplished in the NR/HDPE blend of 60/40 ratio. The NR/HDPE blend at 60/40 ratio compatibilized with HRJ‐10518 and fabricated by a simple plastic injection molding machine exhibited higher ultimate tensile strength and elongation at break (EB). Incorporation of parafinic oil caused a decreasing tendency in tensile strength with increases in EB. The TPNRs exhibited high elastomeric nature with low‐tension set. Copyright © 2007 John Wiley & Sons, Ltd.     

Biodegradable compositions by reactive processing of aliphatic polyester/polysaccharide blends

Commercially available biodegradable aliphatic polyesters, i.e., high molecular weight poly(ϵ-caprolactone) (PCL) and polylactide (PLA), were melt blended with a well-known natural and biodegradable polysaccharide: starch either as corn starch granules or as thermoplastic corn starch after plasticization with glycerol. Conventional melt blending yielded compositions with poor mechanical performances as a result of lack of interfacial adhesion between the rather hydrophobic polyester matrix and the highly hydrophilic and moisture sensitive starch phase. Interface compatibilization was achieved via two different strategies depending on the nature of the polyester chains. In case of PLA/starch compositions, PLA chains were grafted with maleic anhydride through a free radical reaction conducted by reactive extrusion. The maleic anhydride-grafted PLA chains (MAG-PLA) allowed for reinforcing the interfacial adhesion with granular starch as attested by TEM of cryofracture surface. As far as PCL/starch blends were concerned, the compatibilization was achieved via the interfacial localization of amphiphilic graft copolymers formed by grafting of PCL chains onto a polysaccharide backbone such as dextran. The PCL-grafted polysaccharide copolymers were synthesized by controlled ring-opening polymerization of ϵ-caprolactone proceeding via a coordination-insertion mechanism. These compatibilized PCL/starch compositions displayed much improved mechanical properties as determined by tensile testing as well as a much more rapid biodegradation as measured by composting testing.     

Fly ash particles and precipitated silica as fillers in NR/CR vulcanizates under thermal and thermal‐oil ageing

The loading effect of precipitated silica (PSi) and fly ash‐based silica (FASi) on mechanical properties of natural rubber/chloroprene (NR/CR) under thermal and thermal‐oil ageing was investigated with variation in NR content in the NR/CR blends. The selected results were compared with vulcanized NR/nitrile rubber (NR/NBR) blends. The cure time of CR vulcanizate was found to decrease with increasing NR content, but increased with silica fillers. The Mooney viscosity for CR vulcanizates reduced with increasing NR content. The addition of NR had no effect on tensile modulus and tensile strength for the FASi filled NR/CR, but the opposite trend was observed for the PSi filled NR/CR. The post‐curing effect was more significant in PSi filled NR/CR than in FASi filled NR/CR. The tensile strength of the NR/CR vulcanizates was slightly reduced after thermal ageing especially at high NR content, more extreme reduction being found by thermal‐oil ageing. The elongation at break of NR/CR with both silica fillers ranged from 400 to 900%. The hardness results were similar to the tensile modulus. The addition of PSi in NR/CR considerably increased the tear strength, but less pronounced effect was found for FASi. The resilience properties of NR/CR tended to decrease with increasing silica content. The compression set became poorer when NR content was increased. The PSi showed higher improvement in compression set than the FASi. The effects of silica and ageing on the mechanical properties for NR/CR vulcanizates were similar to those for NR/NBR vulcanizates. Copyright © 2009 John Wiley & Sons, Ltd.     

Viscoelastic behavior of polypropylene/nitrile rubber thermoplastic elastomer blends: Application of Kerner's models for reactively compatibilized and dynamically vulcanized systems

The viscoelastic properties of binary blends of nitrile rubber (NBR) and isotactic polypropylene (PP) of different compositions have been calculated with mean‐field theories developed by Kerner. The phase morphology and geometry have been assumed, and experimental data for the component polymers over a wide temperature range have been used. Hashin's elastic–viscoelastic analogy principle is used in applying Kerner's theory of elastic systems for viscoelastic materials, namely, polymer blends. The two theoretical models used are the discrete particle model (which assumes one component as dispersed inclusions in the matrix of the other) and the polyaggregate model (in which no matrix phase but a cocontinuous structure of the two is postulated). A solution method for the coupled equations of the polyaggregate model, considering Poisson's ratio as a complex parameter, is deduced. The viscoelastic properties are determined in terms of the small‐strain dynamic storage modulus and loss tangent with a Rheovibron DDV viscoelastometer for the blends and the component polymers. Theoretical calculations are compared with the experimental small‐strain dynamic mechanical properties of the blends and their morphological characterizations. Predictions are also compared with the experimental mechanical properties of compatibilized and dynamically cured 70/30 PP/NBR blends. The results computed with the discrete particle model with PP as the matrix compare well with the experimental results for 30/70, 70/30, and 50/50 PP/NBR blends. For 70/30 and 50/50 blends, these predictions are supported by scanning electron microscopy (SEM) investigations. However, for 30/70 blends, the predictions are not in agreement with SEM results, which reveal a cocontinuous blend of the two. Predictions of the discrete particle model are poor with NBR as the matrix for all three volume fractions. A closer agreement of the predicted results for a 70/30 PP/NBR blend and the properties of a 1% maleic anhydride modified PP or 3% phenolic‐modified PP compatibilized 70/30 PP/NBR blend in the lower temperature zone has been observed. This may be explained by improved interfacial adhesion and stable phase morphology. A mixed‐cure dynamically vulcanized system gave a better agreement with the predictions with PP as the matrix than the peroxide, sulfur, and unvulcanized systems. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1417–1432, 2004     

Synthesis of natural rubber-g-maleic anhydride and its use as a compatibilizer in natural rubber/short nylon fiber composites

Natural rubber grafted maleic anhydride (NR-g-MAH) was synthesized by mixing maleic anhydride (MAH) and natural rubber (NR) in solid state in a torque rheometer using dicumyl peroxide (DCP) as initiator. Then the self-prepared NR-g-MAH was used as a compatibilizer in the natural rubber/short nylon fiber composites. Both the functionalization of NR with MAH and the reaction between the modified rubber and the nylon fiber were confirmed by Fourier transform infrared spectroscopy (FTIR). Composites with different nylon short fiber loadings (0, 5, 10, 15 and 20 phr) were compounded on a two-roll mill, and the effects of the NR-g-MAH on the tensile and thermal properties, fiber-rubber interaction, as well as the morphology of the natural rubber/short nylon fiber composites were investigated. At equal fiber loading, the NR-g-MAH compatibilized NR/short nylon fiber composites showed improved tensile properties, especially the tensile modulus at 100% strain which was about 1.5 times that of the corresponding un-compatibilized ones. The equilibrium swelling tests proved that the incorporation of NR-g-MAH increased the interaction between the nylon fibers and the NR matrix. The crosslink density measured with NMR techniques showed that the NR-g-MAH compatiblized composites had lower total crosslink density. The glass transition temperatures of the compatibilized composites were about 1 K higher than that of the corresponding un-compabilized ones. Morphology analysis of the NR/short nylon fiber composites confirmed NR-g-MAH improved interfacial bonding between the NR matrix and the nylon fibers. All these results signified that the NR-g-MAH could act as a good compatilizer of NR/short nylon fiber composites and had a potential for wide use considering its easy to be prepared and compounded with the composites.     

POSS nanoparticles as a potential compatibilizer for natural rubber/butadiene rubber blends

In this study, it was aimed to investigate octavinyl‐polyhedral oligomeric silsesquioxane (OV‐POSS) incorporation into natural rubber (NR)/butadiene rubber (BR) elastomer blends as a potential compatibilizer. The effects of OV‐POSS loading levels on the thermal, mechanical, morphological, and dynamic‐mechanical properties of elastomer blends were explored. Fourier‐Transform Infrared Spectrometer (FTIR), Temperature Scanning Stress Relaxation (TSSR), and Differential Scanning Calorimetry (DSC) results revealed the conceivable effect of OV‐POSS nanoparticles in the vulcanization through reacting with sulfur and/or elastomers. Scanning Electron Microscope (SEM), X‐Ray Diffraction (XRD), and tensile test measurements supported the improvement of mechanical properties due to homogeneous dispersion at low loading levels. On the other hand, high amount of OV‐POSS incorporation (7 and 10 phr) resulted in a decrease in mechanical properties, owing to the agglomeration of nanoparticles. According to contact angle and Dynamic mechanical analysis (DMA) results, it could be concluded that OV‐POSS nanoparticles were localized at the interface of the elastomers and enabled the compatibilization of immiscible NR/BR blends.