含氟聚酰亚胺波导波长分离耦合器优化设计

提出并采用统计优化的设计方法解决含氟聚酰亚胺波导波长交叉分离耦合器的偏振态变动的影响.在实测了含氟聚酰亚胺的色散和双折射特性的基础上,优化设计了40路波长信道、1550 nm中心波长、0.8 nm波长间隔的抗偏振变动的波长交叉分离耦合器.数值模拟显示:波长周期偏移小于0.1 nm,1 dB带宽为0.5 nm,3 dB带宽为0.8 nm,串扰小于－30 dB,偏振变动导致的波长漂移小于0.08 nm.     

Design of tunable wavelength microcavity organic electroluminescent diode with liquid crystal

A novel designed method for tunable wavelength microcavity organic electroluminescent diode (MOLED) based on the birefringence of liquid crystal was presented. By modulated the refractive index of liquid crystal, the device could radiate with different wavelength continuously. The simulated result showed that the tunable range could reach to 60 nm and the full width of half maximum is 5.5 nm. The device could be applied to wavelength converter and tunable light source.     

Wavelength demultiplexers based on multimode interference effect in photonic crystals

We present a compact photonic crystal wavelength demultiplexing device based on multimode interference effect. The finite-difference time-domain method is used to verify and analyze the characteristics of the device. Results show the demultiplexing function of the device can be obtained with greater than 20 dB isolation ratio and about 20 nm bandwidth at both wavelength bands.     

声表面波器件变频快速模拟方法*

声表面波器件的级联有限元模拟方法是从整体结构中分离出若干独立的基本单元,通过基本单元边界矩阵的级联实现有限长器件结构的模拟。在实际设计中,通过优化叉指换能器的指条周期,激发出不同波长的声表面波,调整声表面波器件的谐振频率,这导致级联有限元模拟方法存在频繁的单元建模与数据传输过程。为提高模拟效率,该文提出了一种波长(频率)变化时的级联有限元快速模拟方法。首先分析了不同波长对应单元系统矩阵间的关系,引入参考波长及波长变化因子,建立单元系统矩阵与波长之间的简易函数关系。接着利用参考波长的有限元模型快速计算出不同波长对应的单元系统矩阵,避免了多次单元建模与大量数据传输过程。最后利用边界矩阵的级联计算器件的频域响应,证明了该方法的有效性。     

基于体全息技术的波分解复用(WDM)器件研究

为了寻求更高质量和密集度的WDM器件，对体全息技术制作WDM器件的新方法进行了研究。利用耦合波理论讨论了光折变多重体全息光栅作为波长滤波器实现波长解复用的基本原理。通过理论分析得出了最大衍射效率、最佳写入光强比与耦合强度大小的关系表达式。考虑有效电光系数和空间电荷场随写入光路几何组态的变化关系，以及各信道衍射光波长、衍射角等因素对曝光时序的影响，利用递推法推导出更为精确的曝光时序。采用高亮度溴钨灯代替价格昂贵的大功率可调谐激光器作为波长解复用光源，设计出基于体全息技术的16通道波分解复用器的实验方案。理论分析表明，该器件可将波长相隔0.8nm的谱线分开约1.0mm，这有助于实现密集波长的解复用。     

Reduction of light signal pulse distortion in cascaded sum-frequency-generation and difference-frequency-generation wavelength conversion

Cascaded sum-frequency-generation (SFG) and difference-frequency-generation (DFG) can implement a wavelength conversion between arbitrary combinations of input and output signal wavelengths. By using a tunable wavelength pump light, the output wavelength can be tuned to a desired wavelength. As in many wavelength conversion devices using the nonlinear optical effect, the group velocity difference between light pulses with different wavelength causes a walk-off effect deforming the output pulse shape. Thus the device length should be kept short to avoid the walk-off effect resulting in limited conversion efficiency. In this report, we propose a method for a quasi-phase matched (QPM) device to maintain the pulse shape of the SFG light pulse along the propagation distance. The output DFG light pulse deformation is suppressed and the conversion efficiency can be increased by extending the device length.     

Rotating-mirror wavelength shifter

A mechanical method is used to shift the wavelength of a laser light source over a small wavelength range. The device, constructed for use in the field of electronic spectroscopy, uses curved mirrors to give a good wavelength shift stability and a high duty cycle.     

Analysis of Ti:LiNbO3 zero-gap directional coupler for wavelength division multiplexer/demultiplexer

For the purpose of multichannel integrated-optical wavelength division MUX/DEMUX design, the wavelength tuning method of Ti:LiNbO₃ zero-gap directional coupler is analysed by effective-index based matrix method (EIMM). In this method, first, the 2D refractive index profile of the Ti:LiNbO₃ zero-gap directional coupler is transformed into lateral 1D effective-index profile by WKB method. Finally, matrix method is applied to this effective-index profile and the propagation constants are computed from the resonance peaks of the excitation efficiency versus propagation constant characteristics. It has been shown that the channel wavelength tuning can be achieved by varying the Y-branching angle at the input and output of the device or by a slight variation of two-mode-section length. The method of electro-optic fine tuning of the channel wavelength and channel separation of the device has also been investigated. A cascaded structure with proper parameters for four-channel application is also simulated and the results are presented.     

利用改进的熔融拉锥法制备单模光纤波分复用器

研究了熔融拉锥光纤型波分复用器制备过程中各相关参量对其最小信道间隔的影响。并根据理论模拟的结论设计了新型的熔融拉锥装置,其中加热装置为有较长均匀加热区域的条形加热炉,使熔融拉锥光纤型波分复用器的耦合长度显著加长,改善了传统拉锥方法对这一类型波分复用器可达到的最小信道间隔的限制,得到了初步实验结果,最小信道间隔达到3.01 nm。     

Vertical input optical ring resonator with differential operation for optical sensor

A novel waveguide ring resonator optical sensor with two resonant wavelength channels is proposed for a refractive index measurement of a test sample placed on the sensor substrate and its performance characteristics are investigated analytically and numerically. The waveguide device consists of a ring resonator, a split-ring-shaped loop waveguide, and a vertical input/output grating coupler, in which the loop waveguide acts as an additional resonator and provides another output wavelength channel of the sensor. The differential detection between the two wavelength channels enables the highly sensitive detection with temperature compensation. A numerical simulation based on a finite difference time domain (FDTD) method shows that a precise index change detection with a resolution of 10⁻⁶ can be achieved using of the proposed device.     

基于自衍射效应的自参考光谱干涉方法的研究

研究一种基于非线性透明光学介质中的自衍射和自参考光谱干涉的新方法来进行飞秒激光脉冲测量. 实验中, 基于此新方法设计一种简单装置, 对800 nm 中心波长, 约40 fs 近无啁啾飞秒激光脉冲进行测量, 并与自参考光谱相干电场重建法测量结果进行比较, 得到了一致的结果. 此新方法与相应的装置结构简单, 可以对深紫外到中红外光谱范围的飞秒脉冲进行测量. 关键词： 飞秒激光脉冲 自参考光谱干涉 自衍射 脉冲测量     

太赫兹量子阱光电探测器光栅耦合的模拟与优化

光栅耦合是量子阱光电探测器探测正入射电磁辐射的常用耦合方法,本文采用模式展开法研究了一维金属光栅太赫兹量子阱光电探测器中的电磁场分布,并给出了器件有源区中的平均光强.研究结果表明,若一维光栅的周期与太赫兹波在器件材料中的波长相当,并且根据器件结构选取合理的光栅占空比,可使器件中的平均光场最强,光栅的光耦合效率最高,从而提高器件的响应率. 关键词： 太赫兹 量子阱光电探测器 光栅     

Experimental Investigation on Temperature Characteristic and Temperature Control of Fiber Bragg Gratings

１ＩｎｔｒｏｄｕｃｔｉｏｎＦｉｂｅｒＢｒａｇｇｇｒａｔｉｎｇｓ（ＦＢＧｓ）ｈａｖｅａｔｒａｃｔｅｄｍｕｃｈａｔｅｎｔｉｏｎｉｎｒｅｃｅｎｔｙｅａｒｓ［１～３］ｂｅｃａｕｓｅｏｆｔｈｅｉｒａｃｔｕａｌａｎｄｐｏｔｅｎｔｉａｌｉｍｐｏｒｔａｎｔａｐｐｌｉ...     

迈克尔逊干涉仪测波长的一种便捷方法

提出了迈克尔逊干涉仪测波长的一种便捷且精确的测量方法。利用自制的光电计数及电机控制装置,在短时间内无须任何数据处理便可由计数器直接读取待测光源波长值。该方法不仅实现了条纹的全自动计数,又简化了干涉仪繁复的读数环节,更消除了仪器的零点误差。     

785nm便携式光栅外腔可调谐半导体激光器的研制和输出特性

针对移频激发拉曼光谱测试系统的小型化需求,在Littrow结构中,采用商用的785nm大功率激光二极管作为增益器件,构建了一款便携式光栅外腔可调谐半导体激光器。该激光器通过采用一种新型的波长调谐方法,即以改变半导体增益器件相对于准直透镜的水平位置来实现波长的连续调谐,实现了尺寸为140mm×65mm×50mm的小型化结构设计。相比于传统的旋转衍射光栅改变光线在光栅上的入射角来实现波长调谐的方式,该方法有效地缩减了增益器件的平移距离,从而有利于便携式外腔激光器波长的快速宽带调谐。实验结果表明,该激光器具有较宽的波长调谐范围,在340~900mA注入电流下均可实现10nm以上的波长调谐,尤其在900mA大注入电流下,其波长调谐覆盖779.40~791.07nm,调谐范围可达11.67nm,且激射线宽小于0.2nm,单波长输出功率最高可达280mW,放大的自发辐射抑制比大于25dB,呈现出较优异的输出性能,满足移频激发拉曼光谱检测系统对光源的基本要求。此外,该激光器可采用一微型压电陶瓷驱动器来实现波长的电动调谐,实验获得了1.35nm的波长调谐范围,证实了所制785nm便携式光栅外腔可调谐半导体激光器适合作为便携式移频激发拉曼光谱检测系统的光源用于减除原始拉曼光谱中的荧光背景。     

InP基1×4多模干涉耦合器的设计与制作

在密集波分复用系统中,多波长DFB激光器阵列与多模干涉耦合器集成光源器件具有重要的应用前景.为了研制多波长集成光源中的宽带可用低损耗光耦合器,利用三维有限差分光束传播法仿真设计了一种具有强限制作用的InP/InGaAsP材料的多模干涉型耦合器.输入/输出端波导均采用楔形结构以降低多模干涉型耦合器的插入损耗,提高各个输出端口的出光平衡度.根据仿真结果,结合波导芯层为采用外延生长设备,采用反应离子刻蚀工艺制作了1×乘4多模干涉型耦合器.利用自动对准波导耦合测试系统对所制作器件的插入损耗和出光平衡度进行测量.测试结果表明,该器件在1 550 nm波长附近的40 nm带宽范围内获得了约2.6 dB的通带平坦度,在1 550 nm通信波长处,器件的插入损耗低于10 dB.     

InP基1×4多模干涉耦合器的设计与制作

在密集波分复用系统中,多波长DFB激光器阵列与多模干涉耦合器集成光源器件具有重要的应用前景.为了研制多波长集成光源中的宽带可用低损耗光耦合器,利用三维有限差分光束传播法仿真设计了一种具有强限制作用的InP/InGaAsP材料的多模干涉型耦合器.输入/输出端波导均采用楔形结构以降低多模干涉型耦合器的插入损耗,提高各个输出端口的出光平衡度.根据仿真结果,结合波导芯层为采用外延生长设备,采用反应离子刻蚀工艺制作了1×乘4多模干涉型耦合器.利用自动对准波导耦合测试系统对所制作器件的插入损耗和出光平衡度进行测量.测试结果表明,该器件在1 550nm波长附近的40nm带宽范围内获得了约2.6dB的通带平坦度,在1 550nm通信波长处,器件的插入损耗低于10dB.     

Design of a device with wavelength multiplexing and routing functions using dynamic holography on SLMs

This work describes the theory and design of a generic multipurpose device that can operate as a tunable wavelength filter, wavelength multiplexer and wavelength router. This device could be especially useful in optical network applications based in both coarse and dense wavelength division multiplexing technology. The enabling component is a ferroelectric liquid crystal spatial light modulator (SLM) where dynamic holograms are implemented in real time. As a consequence, the device will be able to carry out different functions according to the hologram recorded onto the SLM. The great advantage of this device is a polarization insensitivity operation, allowing low crosstalk and simple handling.     

微通道板近紫外量子效率测量及成像研究

提出了一种通过测量微通道板输出电流及增益来计算光电流,从而测量出微通道板量子效率的方法,并用该方法测量了微通道板在近紫外(200~380nm)的量子效率.测量结果表明,微通道板的量子效率很低,并且随波长增加而快速下降,200nm波长处的量子效率为10-4数量级,320nm波长处的量子效率为10-8数量级,大于340nm波长处的量子效率极低且趋近于零.微通道板及荧光屏组成的成像器件可以对酒精灯火焰成像,但图像较稀疏,而传统Cs2Te光电阴极紫外成像器件的图像却较密实,这与微通道板量子效率低,Cs2Te光电阴极量子效率高的情形一致.在该成像器件的前端放置一片350nm波长的高通滤光片后,所成的酒精灯火焰图像消失.对被照射目标成像时,如果照射光源为254nm的汞灯,则可以成像;但如果照射光源为365nm汞灯,则不能成像.说明微通道板的光谱响应主要在350nm波长以下,与其量子效率的测量结果一致.最后测量得到该成像器件的分辨力为32lp/mm,与传统Cs2Te光电阴极紫外成像器件的分辨力相同.微通道板及荧光屏组成的成像器件由于不使用光电阴极,具有价格低、寿命长且可靠性高的优点,因此可在紫外信号较强或成像距离较短的条件下使用.     

Broad band beam splitter based on the double-groove fused silica grating

In this paper, we propose a broad band 1 × 3 beam splitter operating in the telecommunication wavelength band under normal incidence, this device consisting of a double-groove fused silica grating layer is designed with using the inverse mathematical method and rigorous vector diffraction theory. It is shown from our calculations that the device presents excellent beam splitter ability for TE polarization light with the average diffraction efficiencies is more than 95% over ∼100 nm wavelength range, moreover, the uniformity of our beam splitter is better than 2% in the whole wavelength band. Furthermore, the physical understanding of the diffraction behaviors taking place inside the beam splitter gratings can be explained by the modal method.