Preparation of calibration materials for microanalysis of Ti minerals by direct fusion of synthetic and natural materials: Experience with LA–ICP–MS analysis of some important minor and trace elements in ilmenite and rutile

Calibration materials for microanalysis of Ti minerals have been prepared by direct fusion of synthetic and natural materials by resistance heating in high-purity graphite electrodes. Synthetic materials were FeTiO₃ and TiO₂ reagents doped with minor and trace elements; CRMs for ilmenite, rutile, and a Ti-rich magnetite were used as natural materials. Problems occurred during fusion of Fe₂O₃-rich materials, because at atmospheric pressure Fe₂O₃ decomposes into Fe₃O₄ and O₂ at 1462?°C. An alternative fusion technique under pressure was tested, but the resulting materials were characterized by extensive segregation and development of separate phases. Fe₂O₃-rich materials were therefore fused below this temperature, resulting in a form of sintering, without conversion of the materials into amorphous glasses. The fused materials were studied by optical microscopy and EPMA, and tested as calibration materials by inductively coupled plasma mass spectrometry, equipped with laser ablation for sample introduction (LA–ICP–MS). It was demonstrated that calibration curves based on materials of rutile composition, within normal analytical uncertainty, generally coincide with calibration curves based on materials of ilmenite composition. It is, therefore, concluded that LA–ICP–MS analysis of Ti minerals can with advantage be based exclusively on calibration materials prepared for rutile, thereby avoiding the special fusion problems related to oxide mixtures of ilmenite composition. It is documented that sintered materials were in good overall agreement with homogeneous glass materials, an observation that indicates that in other situations also sintered mineral concentrates might be a useful alternative for instrument calibration, e.g. as alternative to pressed powders.     

Fluorimetric determination of uranium in certain refractory minerals,environmental samples and industrial waste materials

Summary A simple sample decomposition and laser fluorimetric determination of uranium at trace level is reported in certain refractory minerals, like ilmenite, rutile, zircon and monazite; environmental samples viz. soil and sediments; industrial waste materials, such as, coal fly ash and red mud. Ilmenite sample is decomposed by heating with ammonium fluoride. Rutile, zircon and monazite minerals are decomposed by fusion using a mixture of potassium bifluoride and sodium fluoride. Environmental and industrial waste materials are brought into solution by treating with a mixture of hydrofluoric and nitric acids. The laser induced fluorimetric determination of uranium is carried out directly in rutile, zircon and in monazite minerals and after separation in other samples. The determination limit was 1 μg ^. g^-1 for ilmenite, soil, sediment, coal fly ash and red mud samples, and it is 5 μg ^. g^-1 for rutile, zircon and monazite. The method is also developed for the optical fluorimetric determination of uranium (determination limit 10 μg ^. g^-1) in ilmenite, rutile, zircon and monazite minerals. The methods are simple, accurate, and precise and they require small quantity of sample and can be applied for the routine analysis.     

A novel rapid method for preparation of sample solution for chemical characterisation of titanium minerals by atomic spectrometry

A new rapid decomposition and dissolution method with a mixture of sodium di-hydrogen orthophosphate and di-sodium hydrogen orthophosphate as a novel flux is described. The minerals are fused with (1:1) mixture of the above salts (flux) and the melt is dissolved in distilled water. The solution is diluted to desired volume depending on the instrumental technique used for determination. ICP-OES is used for the determination of Al, Ca, Mg, Cr, V, Si, Fe and Ti without interference from titanium, iron and sodium phosphate (introduced as flux). All the elements except Si and V are also determined by AAS. The use of nitrous oxide–acetylene flame eliminates the depression due to titanium in the measurement of Mg, Mn, Cr and Fe in air–acetylene flame. Synthetic mixture conforming to ilmenite and rutile composition are analyzed by ICP-OES and AAS to check the validity of the method. The results are in good agreement. The proposed method has been applied to natural samples and the results are evaluated against the established decomposition method using potassium bisulphate. Both ICP-OES and AAS yielded comparable results. The R.S.D. of the proposed method in case of ICP-OES varies from 0.5 to 2%, whereas for AAS it varies from 1.5 to 3% for different elements (n = 5). The novelty of the proposed sample decomposition lies in its simplicity, ease and speed of fusion with minimal skills besides being eco-friendly unlike the reported tedious complicated decomposition procedures involving variety of fluxes and lot of hazardous chemicals.     

Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS): comparison of different internal standardization methods using laser-induced plasma (LIP) emission and LA-ICP-MS signals.

The source of signal variations that governs the analytical performance of laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) was investigated in this study. In order to specify the source of signal variations of LA-ICP-MS, laser-induced plasma (LIP) Fe emission, LA-ICP-MS Fe+ and LA-ICP-MS Ni+ signals were used as internal standards for the determination of trace elements in low-alloy steel certified reference materials (BS 50D and JSS 1005-1008). Fe 1373.5 nm emission signals from LIP were measured, while trace element LA-ICP-MS signals were collected. After that, the LIP emission signals, LA-ICP-MS Fe+ and LA-ICP-MS Ni+ signals were used as internal standards, and the analytical performance was evaluated by the RSDs and the correlation coefficients (r) of the calibration curves. The improvement factors were dependent on the internal standardization methods. Analytical precisions (RSDs) of trace element LA-ICP-MS signals were improved by factors of 1.5-3.3 using LIP Fe emission signals as an internal standard. The improvement factors of 2.5 - 5.9 and 4.1 - 17 were obtained by using LA-ICP-MS Fe+ and LA-ICP-MS Ni+ signals as internal standards, respectively. Better correlation coefficients (r) were also obtained using the LA-ICP-MS signal compensation (0.9985 by LA-ICP-MS Fe+ and 0.9996 by LA-ICP-MS Ni+) rather than the LIP Fe emission compensation (0.9932). In this paper we compare and discuss the analytical performance achieved by LA-ICP-MS using LIP Fe emission, LA-ICP-MS Fe+ and LA-ICP-MS Ni+ signals as internal standards.     

X射线荧光光谱法分析镁砂的主次成分

采用镁砂标准样品作为校准样品,建立了熔融制样X射线荧光光谱法测定镁砂中MgO,Al2O3,SiO2,CaO,P2O5,Fe2O3的方法。采用熔融法为样品片和校准片的制备方法,选择四硼酸锂-偏硼酸锂（67＋33）为助熔剂,1.00mL LiBr溶液为脱模剂,熔融温度为1 100℃,熔融时间20min。对镁砂样品测定的相对标准偏差（RSD）小于3%,对不同镁砂标准样品进行测定,方法的测定结果与认证值相吻合。     

X射线荧光光谱法测定钾长石、钠长石中多种元素

采用熔融制样,以钾长石、钠长石国家标准样品为主,辅以粘土、炉渣、硅石等标准样品,配制成一系列校准标准样品,用X射线荧光光谱法测定钾长石和钠长石中的Na2O、Al2O3、SiO2、K2O、CaO、Fe2O3、TiO2的含量,结果表明:方法的相对标准偏差为0.065%～2.9%,其测定结果与标准值基本一致,准确度好,可替代湿法化学分析,适合于长石类硅铝酸盐矿物的日常分析。     

熔融法X射线荧光光谱测定岩石主成分含量

选用国家一级标准物质,采用X射线荧光光谱法对岩石样品中的二氧化硅、氧化铝、氧化钙、氧化镁、氧化钾、氧化钠、三氧化二铁、五氧化二磷、氧化钛、氧化锰10种主要组分进行测定,分析结果和标准值或化学值相吻合,各组分测定结果的相对标准偏差小于2％（n=12）。     

Measurement of naturally occurring radioactive materials (NORM) in beach sand minerals using HPGe based gamma-ray spectrometry

This paper discusses the measurement of naturally occurring radioactivity materials (NORM) in beach sand minerals using high resolution gamma spectrometry. In India, the beach sand minerals of economic interest from coastal Kerala, Tamil Nadu and Orissa are enriched with NORM due to the occurrence of monazite deposits and heavy minerals such as zircon, ilmenite, magnetite, garnet, rutile etc. Since many of these ores are rich in ²³²Th and other radio elements, certification of radioactivity levels has become mandatory in recent years. The average activity concentrations of ²²⁶Ra in zircon, rutile and garnet were 3,531, 1,134 and 17 Bq kg^?1, respectively. The average activity concentration of ²³²Th observed in zircon, rutile and garnet were 618, 454 and 64 Bq kg^?1, respectively. Concentration of ²²⁶Ra, ²³²Th, and ⁴⁰K in ilmenite ore ranged from 17.6–444 Bq kg^?1, 80.4–1971 Bq kg^?1 and ≤5.5–25.0 Bq kg^?1, respectively.     

Applications of inductively coupled plasma mass spectrometry and laser ablation inductively coupled plasma mass spectrometry in materials science

Inductively coupled plasma mass spectrometry (ICP-MS) and laser ablation ICP-MS (LA-ICP-MS) have been applied as the most important inorganic mass spectrometric techniques having multielemental capability for the characterization of solid samples in materials science. ICP-MS is used for the sensitive determination of trace and ultratrace elements in digested solutions of solid samples or of process chemicals (ultrapure water, acids and organic solutions) for the semiconductor industry with detection limits down to sub-picogram per liter levels. Whereas ICP-MS on solid samples (e.g. high-purity ceramics) sometimes requires time-consuming sample preparation for its application in materials science, and the risk of contamination is a serious drawback, a fast, direct determination of trace elements in solid materials without any sample preparation by LA-ICP-MS is possible. The detection limits for the direct analysis of solid samples by LA-ICP-MS have been determined for many elements down to the nanogram per gram range. A deterioration of detection limits was observed for elements where interferences with polyatomic ions occur. The inherent interference problem can often be solved by applying a double-focusing sector field mass spectrometer at higher mass resolution or by collision-induced reactions of polyatomic ions with a collision gas using an ICP-MS fitted with collision cell. The main problem of LA-ICP-MS is quantification if no suitable standard reference materials with a similar matrix composition are available. The calibration problem in LA-ICP-MS can be solved using on-line solution-based calibration, and different procedures, such as external calibration and standard addition, have been discussed with respect to their application in materials science. The application of isotope dilution in solution-based calibration for trace metal determination in small amounts of noble metals has been developed as a new calibration strategy. This review discusses new analytical developments and possible applications of ICP-MS and LA-ICP-MS for the quantitative determination of trace elements and in surface analysis for materials science.     

Determination of trace elements in zeolites by laser ablation ICP-MS

Laser ablation inductively coupled plasma mass spectrometry using a quadrupole-based mass spectrometer (LA-ICP-QMS) was applied for the analysis of powdered zeolites (microporous aluminosilicates) used for clean-up procedures. For the quantitative determination of trace element concentrations three geological reference materials, granite NIM-G, lujavrite NIM-L and syenite NIM-S, from the National Institute for Metallurgy (South Africa) with a matrix composition corresponding to the zeolites were employed. Both the zeolites and reference materials were fused with a lithium borate mixture to increase the homogeneity and to eliminate mineralogical effects. In order to compare two different approaches for the quantification of analytical results in LA-ICP-MS relative sensitivity coefficients (RSCs) of chemical elements and calibration curves were measured using the geostandards. The experimentally obtained RSCs are in the range of 0.2-6 for all elements of interest. Calibration curves for trace elements were measured without and with Li or Ti as internal standard element. With a few exceptions the regression coefficients of the calibration curves are better than 0.993 with internal standardization. NIM-G granite reference material was employed to evaluate the accuracy of the technique. Therefore, the measured concentrations were corrected with RSCs which were determined using lujavrite reference material NIM-L. This quantification method provided analytical results with deviations of 1-11% from the recommended and proposed values in granite reference material NIM-G, except for Co, Cs, La and Tb. The relative standard deviation (RSD) of the determination of the trace element concentration (n = 5) is about 1% to 6% using Ti as internal standard element. Detection limits of LA-ICP-QMS in the lower microg/g range (from 0.03 microg/g for Lu, Ta and Th to 7.3 microg/g for Cu, with the exception of La) have been achieved for all elements of interest. Under the laser ablation conditions employed (lambda: 266 nm, repetition frequency: 10 Hz, pulse energy: 10 mJ, laser power density: 6 x 10(9) W/cm2) fractionation effects of the determined elements relative to the internal standard element Ti were not observed.     

Al掺杂α-Fe2O3材料的制备、表征和气敏特性

采用均相沉淀法制备了纯α-Fe2O3(300 ℃煅烧)和Al掺杂α-Fe2O3(300和400 ℃煅烧), 使用SEM, XRD, ICP和红外光谱等手段进行表征, 并利用气敏仪测试无水乙醇和90＃汽油在不同条件下对材料的响应性能. 结果表明, 微量Al掺杂不改变α-Fe2O3材料的物相, 但会阻碍晶粒生长, 使颗粒变小及Fe2O3晶格间隙中的铁原子数目增多, 材料的导电率增大, 从而显著提高材料的气敏性能. Al掺杂α-Fe2O3对乙醇的响应性能优于对汽油的响应性能, 在乙醇气氛中, 材料对湿度仍然不敏感. 经400 ℃煅烧的Al掺杂α-Fe2O3稳定性较好, 可作为检测乙醇气体的半导体气敏材料.     

An investigation of calibration materials for the measurement of metals in ambient particulate matter on filters by LA-ICP-MS

Three different types of simple and low-cost calibration material for the measurement of the metals content of ambient particulate matter (PM) on filters using laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) have been compared: cellulose ester filters spiked with multi-element calibration solutions, pellets of compressed ambient particulate matter certified reference material (CRM), and powdered ambient particulate matter CRM adhered to a surface. Elements determined were As, Cd, Cr, Cu, Fe, Mn, Ni, Pb, V and Zn, each at approximate levels of 1000?ng per filter. Blank filters spiked with multi-elemental standards were found to be significantly more reproducible and repeatable than materials based on powdered reference materials. However, a comparison of these spiked filters with real samples of ambient PM showed that the analytical sensitivities obtained per mass of analyte were significantly different. It is concluded that the spiked filters could act as very effective quality control standards correcting, to within 1%, drifts in LA-ICP-MS measurements of up to 10%, or as indirect calibration materials supported by additional measurements using traditional wet chemical techniques.     

Preparation and characterization of calibration standards for bone density determination by micro-computed tomography

Phantoms for the calibration of local bone mineral densities by micro-computed tomography (microCT), consisting of lithium tetraborate (Li(2)B(4)O(7)) with increasing concentrations of hydroxyapatite [HAp, Ca(10)(PO(4))6(OH)2] have been prepared and characterized for homogeneity. Large-scale homogeneity and concentration of HAp in the phantom materials was determined using laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS), while homogeneity on the micrometer scale was assessed through microCT. A series of standards was prepared by fusion of pure HAp with Li(2)B(4)O(7) in a concentration range between 0.12 and 0.74 g cm(-3). Furthermore, pressed and sintered pellets of pure HAp were prepared to extend the calibration range towards densities of up to 3.05 g cm(-3). A linear calibration curve was constructed using all individual standard materials and the slope of the curve was in good agreement with calculated absorption coefficients at the effective energy of the microCT scanner.     

Analysis of cement and cement raw meal by atomic absorption spectrophotometry using a new fusion agent

A new fusion agent is proposed for the analysis of cement and cement raw meal using AAS. In the described method, 0.8 g of the fusion agent, consisting of equal portions of oxalic acid, lithium carbonate and lithium tetraborate, was mixed with 0.2 g of the sample, and the mixture was fused for 10 min at 925 degrees C in a platinum crucilbe. The fusion cake was dissolved with dilute hydrochloric acid (1 + 10) and diluted to 500 ml for the determination of Si, Al, Fe, Ti, Na and K expressed as SiO(2), Al(2)O(3), Fe(2)O(3), TiO(2), Na(2)O, and K(2)O respectively. For the determination of Ca and Mg (expressed as CaO and MgO respectively), 10 ml of the previous sample solution were mixed with 4 ml of 6% (m/v) lanthanum nitrate solution and the solution was diluted to 100 ml. The method was found to have good accuracy and precision. The time required to determine the eight elements was around 80 min for each sample.     

Influence of Sn4+ on the structural and electronic properties of Ti1-xSnxO2 nanoparticles used as photocatalysts

Ti(1-x)Sn(x)O(2) nanocrystalline materials employed for photocatalysis have been characterised by means of X-ray diffraction, Raman, X-ray absorption (XANES and EXAFS) and UV-Vis spectroscopy and high resolution transmission electron microscopy. Single-phase samples with anatase or rutile type structures and similar tin contents permitted a separate study of the effect of Sn(4+) ions on these crystalline forms, whereas materials composed of anatase and rutile mixtures were used to investigate the distribution of the dopant cations when both phases coexist. The results obtained from the single-phase doped TiO(2) samples indicate that the presence of tin causes a different effect when doping anatase or rutile in both their structural and electronic properties. While a random substitution of Sn(4+) for Ti(4+) seems plausible for the rutile phase, some kind of gradient in Sn(4+) concentration is possible in anatase. On the other hand, when anatase and rutile coexist, effects of doping are visible in both phases. Regarding chemical composition, a homogeneous distribution of tin was found in both calcined and hydrothermal multiphase samples. Photocatalytic experiments show that both tin-doping and coexistence of different phases have a beneficial effect on the activity of the catalysts.     

Nitrogen photofixation on nanostructured iron titanate films

A nanostructured iron titanate thin film has been prepared by a sol-gel method from iron(III) chloride and titanium tetraisopropylate. Energy-dispersive X-ray analysis and M?ssbauer spectroscopy suggest the presence of a Fe(2)Ti(2)O(7) phase, which was previously obtained as an intermediary phase upon heating ilmenite. In the presence of ethanol or humic acids and traces of oxygen, the novel film photocatalyzes the fixation of dinitrogen to ammonia (17 microM) and nitrate (45 microM). In the first observable reaction step, hydrazine is produced and then undergoes further photoreduction to ammonia. Oxidation of the latter by oxygen affords nitrate as the final product. Since the reaction occurs also in air and with visible light (lambda>455 nm), and since the iron titanate phase may be formed by the weathering of ilmenite minerals, it may be a model for mutual nonenzymatic nitrogen fixation in nature.     

X-ray fluorescence analysis of rare earth elements in rocks using low dilution glass beads.

Major and trace elements (Na, Mg, Al, Si, P, K, Ca, Ti, Mn, Fe, Rb, Sr, Y, Zr, La, Ce, Pr, Nd, Sm, Gd, Dy, Th and U) in igneous rocks were assayed with fused lithium borate glass beads using X-ray fluorescence spectrometry. Low dilution glass beads, which had a 1:1 sample-to-flux ratio, were prepared for determination of rare earth elements. Complete vitrification of 1:1 mixture required heating twice at 1200 degrees C with agitation. Extra pure reagents containing determinants were used for calibrating standards instead of the rock standard. The calibration curves of the 23 elements showed good linearity. Furthermore, the lower limits of detection corresponding to three times the standard deviation for blank measurements were 26 mass ppm for Na2O, 6.7 for MgO, 4.5 for Al2O3, 4.5 for SiO2, 18 for P2O5, 1.1 for K2O, 4.0 for CaO, 3.9 for TiO2, 1.6 for MnO, 0.8 for Fe2O3, 0.5 for Rb, 0.2 for Sr, 0.4 for Y, 0.5 for Zr, 3.3 for La, 6.5 for Ce, 2.7 for Pr, 2.1 for Nd, 1.7 for Sm, 0.7 for Gd, 2.7 for Dy, 0.5 for Th, and 0.6 for U. Using the present method, we determined the contents of these 23 elements in four rhyolitic and granitic rocks from Japan.     

Study of heterogeneities in steels and determination of soluble and total aluminium and titanium concentration by laser ablation inductively coupled plasma mass spectrometry

A methodology for bulk analysis of Al and Ti and for determination of soluble and total Al and Ti concentration in steel samples by laser ablation inductively coupled plasma mass spectrometry was developed. The spatial distribution (both at surface and within the sample) of the insoluble fraction of Al and Ti was also qualitatively estimated. Certified reference materials (CRMs) SS-451 to 460 (carbon steel) and 064-1 (Nb/Ti interstitial free steel), from BAS, and JK 2D (carbon steel) and JK 37 (highly alloyed steel), from SIMR, were studied. It was demonstrated that the insoluble fraction of Al and Ti is heterogeneously distributed. A series of nine glass samples (fused beads) with fixed Fe content and different Al and Ti contents was prepared by melting appropriate amounts of Fe₂O₃, Al₂O₃ and TiO₂ with a lithium tetraborate–sodium carbonate mixture. Quantitative determinations were performed by using calibration graphs obtained from the synthetic fused beads, with ⁵⁷Fe as internal standard; line scan laser sampling mode was used, focusing the laser beam at the sample surface. The optimized laser operating parameters were: laser pulse energy of 1.5 mJ, pulse repetition rate of 5 Hz, scanning speed of 5 μm s⁻¹ and preablation time of 20 s. The concentrations obtained for bulk analysis of CRM samples corresponded with the certified values within the experimental uncertainty. An acceptable concordance between certified and found values was attained for the determination of soluble and total Al and Ti in CRM 064-1 sample.     

Synthesis and Characterization of Photocatalytic Porous Fe3+/TiO2 Layers on Glass

Wet chemical synthesis and preliminary photocatalytical characteristics of titania and Fe(III)-containing TiO₂ layers are presented. A highly stable coating colloids could be prepared under base- as well as acid-catalyzed condensation conditions. Structural properties of the as-prepared wet gels and sintered films were investigated using SEM, TEM, XRD as well as optical absorption spectroscopy, DTA-TG analysis and photomineralisation studies. X-ray amorphous wet titania gel layers start to crystallize at 500°C forming the characteristic anatase phase. In the presence of iron ions (Fe/Ti = 1), nanocrystalline FeTiO₃ ilmenite phase forms. Both TiO₂ and Fe-containing TiO₂ films demonstrate a photocatalytic activity in the process of the photomineralization of dichloroacetic acid.     

Analysis of cement by atomic absorption spectrophotometry and volumetric method

A new method to determine the composition of cement raw mix and cement is devised. The sample was fused with a mixture of sodium carbonate and lithium tetraborate (3:1) at 925 degrees C for 10 min. The fusion cake was dissolved in hydrochloric acid. The concentration of analyte in solution was either determined by atomic absorption spectrophotometry or titrimetry. The proposed method is quick and the analysis for interested oxides (SiO(2), Al(2)O(3), Fe(2)O(3), and CaO) can be completed within 1 hr. The accuracy and precision are comparable to that of X-ray fluorescence spectrometry.