Temperature dependence of the critical current in YBa2Cu3O7−δ and Bi2Sr2Ca1Cu2O8 Josephson junctions

We have studied the stationary Josephson effect on YBa₂Cu₃O_7−δ (T_c=90 K) and Bi₂Sr₂Ca₁Cu₂ O₈ (T_c=80 K and 87 K for two samples of different origin) ceramic based junctions. The temperature dependence of the critical current near T_c has been found as I_c≈(T_c-T) for the Y-Ba-Cu-O samples indicating that they should be classified as S-N-I-N-S type junctions. The I-V curves of the Bi-Sr-Ca-Cu samples show the typical behaviour of S-I-S structures. Using Ambegaokar-Baratoff's theory for Bi₂Sr₂Ca₁Cu₂O₈, the temperature dependence of the superconducting state gap Δ(T) was calculated and it was evaluated that 1.452Δ(0)/k_BT_c3.5.     

High critical current density YBa2Cu3O7−δ tapes prepared by the surface-oxidation epitaxy method

YBa₂Cu₃O_7−δ (YBCO) films with high critical current density (J_c) were successfully fabricated on nickel tapes buffered with epitaxial NiO. NiO was prepared on the textured nickel tape by the surface-oxidation epitaxy (SOE) method. We have reported so far a critical temperature (T_c) of 87 K and J_c=4–6×10⁴ A/cm² (77 K, 0 T) for the YBCO films on NiO/Ni tapes. To enhance the superconducting properties of the YBCO films on the SOE-grown NiO, depositions of thin oxide cap layers such as YSZ, CeO₂, and MgO on NiO were investigated. These oxide cap layers were epitaxially grown on NiO and provided the template for the epitaxial growth of YBCO films. Substantially improved data of T_c=88 K and J_c=3×10⁵ A/cm² (77 K, 0 T) and 1×10⁴ A/cm² (77 K, Hc, 4 T) were obtained for YBCO film on NiO, by using a MgO cap layer with a thickness of 50 nm. The method described in this paper is a simple way to produce long YBCO tape conductors with high-J_c values.     

Measurement of the slope parameter for the neutral pion spectrum in KL → πππ decay

The π⁰ spectrum in the K_L⁰ → 3π decay was measured using a wire chambers magnetic spectrometer. In the usual approximation, the matrix element can be expressed as: M² ≈ 1 + 2a₀(M_K/M_π²)(2T_π⁰−T_π⁰max) + a₁(M_K²/M_π⁴)(2T_π⁰−T_π⁰max)². We obtained a₀ = −0.282 ± 0.011 and a₁ consistent with zero.     

Linear and nonlinear critical magnetic properties and transport in Nd0.75Ba0.25MnO3 single crystal: evidence for its anomalous critical behavior near TC

The data on the resistance and magnetoresistance (MR) as well as measurements of the linear and nonlinear susceptibilities are presented for a Nd_0.75Ba_0.25MnO₃ single crystal with the Curie temperature T_C≈129 K. Although this compound remains insulating in the ferromagnetic state, its resistance has an anomaly near T_C and it reveals the colossal magnetoresistance. The data on the magnetic response are well described by the dynamic scaling theory for 3D isotropic ferromagnets in the paramagnetic critical region at τ>τ^*≈0.11, τ=(T−T_C)/T_C. Below τ^* an anomalous critical behavior is found that suggests the coexistence of two magnetic phases. This behavior is discussed in terms of a phase separation which can occur in the moderately doped manganites exhibiting an orbital ordering.     

Thermal transport in the oxygenated magnetic superconductor, Eu1.5Ce0.5RuSr2Cu2O10+δ

The thermal conductivity and thermopower are reported for a hole doped Eu_1.5Ce_0.5RuSr₂Cu₂O_10+δ sample that has been annealed at 1100 K under an oxygen pressure of 54 atm. At T_c=45 K superconductivity and weak ferromagnetism coexist (T_m=180 K). Weak features in the thermopower, S(T), and thermal conductivity, κ(T), are observed both at T_m and at T^*=140 K. The thermopower begins to decrease sharply toward zero at T_c, and there is an extremely sharp increase of about 30% in the thermal conductivity at T_c. This “first order” transition may be related to the sudden appearance of a spontaneous vortex phase at T_c. A small shoulder is observed in κ(T) in the temperature range T=5–13 K.     

Superconductivity and crystallographic properties of La2 − xMxCuO4 − δ (M = Na, K)

Superconductivity and crystallographic properties of La_{2 − x}M_xCuO_{4 − δ} (M = Na, K) are studied. In the La_{2 − x}M_xCuO_{4 − δ} system, superconductivity is detected for x 0.2. Oxygen content analysis shows that the system has more oxygen vacancies than the La_{2 − x}Sr_xCuO_{4 − δ} system. These oxygen vacancies may reduce the hole concentration, and high Na-doping is needed to produce superconductivity. In the La_{2 − x}K_xCuO_{4 − δ} system, superconductivity is observed for the first time. Resistivity and magnetic susceptibility measurements show that T_c(onset) is 40 K and the Meissner volume fraction is about 4% for x = 0.7. The system changes from orthorhombic to a tetragonal K₂NiF₄ structure at x ≈ 0.3 and only tetragonal samples show superconductivity.     

Magnetic moments and Fe hyperfine field interactions in Y(Fe1−xRux)2 ternaries

Measurements of magnetization and ⁵⁷Fe Mössbauer spectra have been made for Y(Fe_1−xRu_x)₂. The C15 type cubic structure is stabilized for xx 0.7. The C15 compounds is ferromagnetic with T_c200 K and its saturation moment decreases monotonically with increasing x, while the ⁵⁷Fe hyperfine field decreases only slightly with x. From these results, it is deduced that the Ru atoms have an induced moment of ≈1μ_B in the range x 0.2. In the C14 type phase, no magnetic ordering develops even at 4.2 K.     

Synthesis of YBa2Cu3O7−x superconducting thin films on LaAlO3 by means of PAMOCVD

High-T_c superconducting thin films have been deposited in situ by means of a plasma assisted metal-organic chemical vapour deposition (PAMOCVD) process on LaAlO₃. An EMCORE high-speed rotating disc reactor was used to deposit the films at a substrate temperature of 600°C to 800°C. The system is equipped with a (remote) 120 W microwave plasma generator. The oxidising plasma gas is N₂O and/or O₂ while Ar was used as the inert carrier gas for the different metal-organics. The influence of different process parameters (such as the temperatures of the metal-organics, substrate temperature, and plasma gas composition) on the superconductive properties and on the morphology of the films was investigated. Surface morphology and composition were studied by SEM/EDX or EPMA, and AC susceptibility measurements were used to investigate the superconductive properties (T_c and J_c). X-ray diffraction measurements indicated that single-phase YBa₂Cu₃O_7−x films were epitaxially grown with the 00l orientation perpendicular to the substrate surface. The critical temperature (T_c) of the films is about 90 K and the critical current density (J_c) is higher than 10⁶ A/cm² at 77 K and zero field.     

The effects of substrate temperature on the superconducting properties of Tl2Ca2Ba2Cu3O10 films sputter-deposited from stoichiometric oxide targets

The annealing characteristics and the superconducting properties of Tl₂Ca₂Ba₂Cu₃O₁₀ thin films sputter-deposited onto yttrium- stabilized ZrO₂ substrate at up to 500°C from two stoichiometric oxide targets are reported. The films deposited at 400–500°C were found to require a lower post-annealing temperature than the films deposited at lower temperatures to attain the highest T_c superconducting state, due to a more pronounced Ba diffusion toward the substrate as indicated by their secondary ion mass spectrometry depth profiles. The highest T_c achieved tends to degrade with increasing substrate temperatures, a zero resistance T_c of 121 and ≈90 K, respectively, being observed for the films deposited at -ambient temperature and at 500°C. The formation of the highest T_c phase (Tl₂Ca₂Ba₂Cu₃O₁₀) generally is associated with a sheet type of crystal growth morphology with smooth and aligned surfaces which can be obtained only from the films capable of sustaining prolonged annealing at 900°C. Annealing at lower temperatures (≈860°C) results in the formation of rod or sphere type of morphologies with rough and randomly oriented crystals and the lower T_c phases such as Tl₂Ca₁Ba₂Cu₂O₈.     

Electrical transport and superconductivity in the Al2O3-Bi2Sr1.8Ca1.2Cu2Oy and MgO-Bi2Sr1.8Ca1.2Cu2Oy composites

We have measured the resistivities of Al₂O₃-Bi₂Sr_1.8Ca_1.2Cu₂O_y and MgO-Bi₂Sr_1.8Ca_1.2Cu₂O_y composites with the nominal Bi₂Sr_1.8Ca_1.2Cu₂O_y volume fraction, ₂₂₁₂, ranging from 0.15 to 1.00. For the Al₂O₃-Bi₂Sr_1.8Ca_1.2Cu ₂O_y composites, we find for the samples with ₂₂₁₂≥0.6 that the superconducting transition temperature, T_c, is not disturbed by the addition of Al₂O₃. For ₂₂₁₂<0.3, no zero-resistivity state is observed. For the MgO-Bi₂Sr_1.8Ca_1.2Cu₂O_y composites, T_c is barely disturbed for the samples with ρ₂₂₁₂≥0.7. No superconducting state is observed for the samples with ρ₂₂₁₂<0.35. The variation of (300 K) with ρ₂₂₁₂ indicates a three-dimensional percolating Bi-Sr-Ca-Cu-O matrix occurring at ρ₂₂₁₂≈0.19 and ≈0.15 in Al₂O₃-Bi₂Sr_1.8Ca_1.2 Cu₂O_y and MgO-Bi₂Sr_1.8Ca_1.2Cu₂O_y, respectively. Both resistivity and magnetization measurements suggest that the reactions of Bi₂Sr_1.8Ca_1.2Cu₂O_y with MgO are weaker than with Al₂O₃.     

Realization and properties of ramp-type YBa2Cu3O7−δ/Au/Nb junctions

All-thin-film ramp type Josephson junctions between YBa₂Cu₃O_7−δ and Nb have been fabricated. This procedure allows connections between high-T_c and low-T_c superconductors at different crystal sides of the high-T_c superconductor on one chip, which is of great interest for novel phase devices. A thin Au layer is incorporated as a chemical barrier to avoid oxygen transfer from the YBa₂Cu₃O_7−δ to the Nb. Critical current densities up to 600 A/cm² are obtained at T=4.2 K, with typical R_nA values of 0.8 μΩ cm². The variation of the magnetic field dependence of the critical current with the angle between the junction barrier and the YBa₂Cu₃O_7−δ crystal axes is explained by considering a predominant d_x²−y² order parameter symmetry of the YBa₂Cu₃O_7−δ. The successful fabrication of these junctions allows the implementation of novel superconducting electronics, such as complementary Josephson circuitry or proposed qubit concepts, using the unconventional order parameter symmetry of the high-T_c superconductor.     

Effect of partial substitution of Ni and Zn for Cu in CaBaLaCu3O7−δ superconductor

Superconducting behaviour of the tetragonal superconductor CaBaLaCu₃O_7−δ (T_c = 70 K) has been studied as a function of substitution of Ni and Zn for Cu. Both electrical resistivity and AC susceptibility measurements show that T_c decreases monotonically with increasing concentration of the substituent ion, within the composition range where the samples remain single phase, although Zn suppresses T_c more strongly than Ni for equivalent concentrations. It is argued that the suppression of T_c in this system cannot be explained by the Abrikosov-Gorkov mechanism alone.     

Structure and superconductivity of HgBa2CuO4+δ

We have used neutron powder diffraction to investigate the defect structure of HgBa₂CuO_4+δ. An interstitial oxygen defect in the Hg plane is the primary doping mechanism. A superconducting transition temperature, T_{c onset}, of 95 K is achieved when ≈0.06 oxygen atoms per formula unit are incorporated at this site by annealing the sample at 500°C in pure oxygen. Annealing in argon at 500°C lowers the oxygen content in this site to ≈0.01 and results in a T_c of 59 K. The neutron powder diffraction data give evidence for a second defect in the Hg plane which we conclude involves the substitution of copper for about 8% of the mercury and the incorporation of additional oxygen (≈0.1 atoms per formula unit), presumably bonded to the copper defects. In the present samples, the concentration of this defect does not vary with synthesis conditions and its contribution to doping is, therefore, unclear. The structure of the compound is the same at room temperature and superconducting temperatures.     

ESR of double-perovskite Sr2FeMoO6

We present an ESR study of Sr₂FeMoO₆ in the paramagnetic region. A single line at g≈2 was associated with Fe³⁺ ions. The intensity follows Curie–Weiss law in the whole T range. For T >500 K a secondary line is attributed to ferromagnetic (FM) impurities. The line width is described by ΔH_pp(T)=ΔH_pp(∞)(1−Θ/T) with a high value for ΔH_pp(∞). The absence of narrowing effects is a signature of double-exchange (DE) interactions and indicates that DE drives the FM ordering at a relatively high T_c.     

NMR study of local hole distribution, spin fluctuation and superconductivity in Tl2Ba2Ca2Cu3O10

⁶³Cu, ¹⁷O and ²⁰⁵Tl NMR have been performed in the high-T_c superconductor Tl₂Ba₂Ca₂Cu₃O₁₀ whose T_c(max) is 127 K. The hole densities at Cu and oxygen sites in the CuO₂ plane have been extracted from the nuclear quadrupole frequency ν_Q. The striking feature is that the Cu holes are significantly transferred to oxygen site due to strong hybridization between Cu and oxygen. From an analysis of T₁ and T_2G, it has been found that the spectral weight of the spin fluctuation is transferred to higher energy compared to YBa₂Cu₃O₇, while the magnetic correlation length ξ does not differ much. Thus, it is suggested that the higher T_c is due to higher characteristic energy of spin fluctuations, i.e. the superconductivity is spin fluctuation mediated. The superconducting properties are consistently explained by a d-wave superconductivity model with a finite density of states (DOS) at the Fermi level. We show that the disorder of the Ca/TlO layer caused by the partial inter-substitution of Tl and Ca is responsible for the potential scattering to produce such a DOS. It is found that if such a potential scattering were absent, T_c would go up to 132 K which is quite close to the record T_c realized in the Hg based compound.     

Dynamic contribution to the fishtail effect in a twin-free DyBa2Cu3O7−δ single crystal

Superconducting current densities j_s and dynamic relaxation rates Q d ln j_s/d In(dB_e/dt), where dB_e/dt is the sweep rate of the external magnetic field B_e, were measured as a function of temperature (5 K < T < 65 K) in magnetic fields up to 7 T on a twin-free DyBa₂Cu₃O_7−δ single crystal by means of a high-sensitivity capacitance torque magnetometer. Above 15 K, we observe a “fishtail” effect, i.e. a pronounced minimum in the j_s(B_e) curve at fields around B_e = 1 T. The relaxation rate Q shows an anomalous increase at low fields which is correlated to the minimum in the j_s(B_e) curve. Both the j_s versus B_e and Q versus B_e data are used as input parameters into the generalized inversion scheme developed by Schnack et al. [Phys. Rev. B 48 (1993) 13178] to calculate the true critical current density j_c which is by definition independent of relaxation effects. Interestingly, the j_c(B_e, T) curves derived in this way do not show a minimum. This points clearly to a dynamic contribution to the fishtail effect. The true critical current density j_c(B_e, T) decreases weakly with increasing B_e over the entire measured temperature and field range, as expected for single-vortex pinning. This indicates that the observed fishtail effect is not caused by a crossover from single-vortex pinning to pinning of flux bundles. The temperature dependence of j_c is in good agreement with the predictions of a model based on single-vortex pinning caused by spatial fluctuations in the charge-carrier mean free path.     

Study of the magnetic properties of single-crystal Ba0.6K0.4BiO3

The magnetic properties of single-crystal Ba_0.6K_0.4BiO₃ were studied. The results show that this isotropic superconductor (cubic structure with T_c ≈ 32 K) exhibits irreversibility and relaxation properties similar to those observed in the layered, high temperature superconductors. For fields above 0.1 T, an irreversibility line B_irr = B_irr (0) (1 − t)ⁿ with n = 3/2 and B_irr (0) = 20 T is observed. The comparison among several superconducting systems with different anisotropies suggests that the irreversibility line is unlikely to be the melting line for the YBa₂Cu₃O_7−δ.     

Na2TiGeO5: Crystal structure stability at low temperature and high pressure

The temperature evolution of the lattice parameters measured from 295 to 125 K exhibits a small instability below T_c≈278 K, indicating ferroelastic properties of Na₂TiGeO₅. The behavior is related to the specific crystal structure built of polyhedral layers with shared TiO₅ pyramids and GeO₄ tetrahedra, alternating with layers of Na⁺ cations. Antiparallel alignment of the short apical titanyl bond in adjacent rows of the polyhedral layer gives rise to spontaneous strain, when a distortion of the TiO₅ groups occurs. Single-crystal structures determined at room temperature and 120 K suggest that {1 1 0} domains, developing below T_c, entail a tetragonal-to-orthorhombic symmetry change. The mechanism is attributed to a shortening of the O–O distance between the polyhedral layers, and to minor shifts of the positions of the Ti atoms and the correlated oxygen atoms along the c-axis. The structure distortion, however, is too small to allow any unambiguous determination of the symmetry-breaking effects. The bulk modulus and its pressure derivative have been determined as B₀=89(2) GPa and . A pressure-induced phase transformation takes place at P_c≈12.5 GPa, presumably to an orthorhombic structure. The pressure effect on the transition temperature is given by ΔT_c/ΔP≈1.76 K/GPa.     

Effect of a magnetic field on MnAs0.88P0.12 below 80 K

MnAs_0.88P_0.12 has been studied by powder neutron diffraction in external magnetic fields up to 15.2 kOe and temperatures down to 4.2 K. MnAs_0.88P_0.12 takes the MnP type atomic arrangement and exists in para-, ferro- and different (essentially) helimagnetic states. The observation of a double 000^± satellite at 4.2 K < T 70 K adds further evidence to the chain of arguments for distinction between the helimagnetic states H'_a (4.2 K < T < T_S,1 ≈ 70 K) and H_a (T_S,2 ≈ 180 K < T < T_N = (243 ± 5) K). External magnetic fields at 4.2 K < T < 70 K evoke a new magnetic state, which is also characterized by a satellite doublet, and is tentatively designated H'_a,fan.     

Charge ordering in Eu3S4 determined by the valence-difference contrast of synchrotron X-ray diffraction

Synchrotron X-ray diffraction study for single crystals of Eu₃S₄ has revealed that a Th₃P₄-type structure transforms to a charge-ordered one at T_c=188.5 K. The crystal structures of Eu₃S₄ at T=300, 180 and 160 K were determined in the least-squares refinements with the Mo K intensity data. The valence-difference contrast method was applied at the L_II absorption edge of Eu, utilizing a large difference in anomalous scattering factors between Eu²⁺ and Eu³⁺. The cation distribution of Eu²⁺ and Eu³⁺ was determined by crystal-structure analyses based on the intensity data collected at two wavelengths of λ=1.6312 and 1.6298 Å.The least-squares structural refinements suggest that the most plausible atomic arrangement is [Eu³⁺]^4a[Eu²⁺Eu³⁺]^8dS₄. The charge-ordering scheme is that a half of Eu³⁺ ions occupy the whole 4a sites in the crystal structure, while the remaining half of Eu³⁺ ions mix with Eu²⁺ in the 8d sites. The scheme is also supported by the energy dependence of Bragg intensities for 400 and 004 reflections.