High resolution capillary GC–MS analysis of low molecular weight organic compounds in municipal wastewater

High resolution capillary gas chromatography–mass spectrometry has been used in combination with various sample preparation methods to analyze a wide range of low molecular weight organic contaminants in municipal wastewaters. Volatile organic compounds were extracted using a purge and trap concentrator connected directly to a wide bore DB-624 capillary column. Because of the high organic load in wastewater samples, this method was preferred to the more sensitive closed loop stripping technique which suffered from competition effects and insufficient adsorbent capacity. Volatile and semi-volatile base/neutral compounds and acids were extracted with dichloromethane at pH 11 and pH 2, respectively, or were recovered using a simultaneous distillation-extraction procedure. Acidic compounds were subsequently derivatized using diazomethane methylation. Both fractions were separated with a 30m DB-5ms capillary column. Specific ionic substances (LAS, NTA, EDTA) were isolated by solid-phase extraction then derivatized with diazomethane (LAS) or acetyl chloride in n-butanol (NTA, EDTA) before GC–MS analysis. This array of techniques enabled the identification of more than 150 organic contaminants in the influent of a municipal wastewater treatment plant in northern suburban Paris. The individual concentrations of these contaminants ranged from < 0.1 μg/l to 5.7 mg/l.     

Comparison of GC–MS and MEKC methods for caffeine determination in preworkout supplements

In this study, GC–MS‐ and MEKC‐based methods for determination of caffeine (CAF) in preworkout supplements were developed and validated. The proposed protocols utilized minimal sample preparation (simple dilution and syringe filtration). The developed methods achieved satisfactory validation parameters, i.e. good linearity (R² > 0.9988 and R² > 0.9985 for GC–MS‐ and MEKC‐based method, respectively), satisfactory intra‐ and interaccuracy (within 92.6–100.7% for method utilizing GC–MS and 92.1–110.3% for protocol based on MEKC) and precision (CV < 15.9% and CV < 6.3% for GC–MS‐ and MEKC‐based method, respectively) and recovery (within 100.1–100.8% for method utilizing GC–MS and 101.5–106.2% for protocol based on MEKC). The LOD was 0.03 and 3 μg/mL for method utilizing GC–MS and MEKC, respectively. The CAF concentrations determined by GC–MS‐ and MEKC‐based methods were found to be in the range of 8.53–11.23 and 8.20–11.61 μg/mL, respectively. Taking into consideration information on the labels, the investigated supplements were found to contain from 110.0 to 167.3% of the declared CAF content, which confirmed the literature reports on incompatibility of the declared product compositions with real ones. Nevertheless, the consumption of examined supplements as recommended by producers did not lead to exceeding the CAF safe limit of 400 mg per day. Additionally, the MEKC‐based method allowed for detection and identification of vitamin B3 and B6 in all of the investigated supplement samples, which demonstrated that MEKC‐based protocols may be an appropriate assays for simultaneous determination of CAF and vitamins.     

GC–SIM/MS Profiling of Urinary Steroids as their Per-trimethylsilyl Derivatives

Complete GC–SIM/MS separation and identification of 19 steroids (including several steroid isomers) in a male urine sample, as their per-trimethylsilyl ethers, is described. Trimethylsilylation of their functional groups (hydroxyl and carbonyl) was achieved by a rapid, simplified and one-step derivatization method, using N -methyl- N -trimethylsilyl-2,2,2,-trifluoroacetamide as the silylating agent and the solvent as well, along with catalytic amounts of trimethylsilyl iodide and dithioerythritol. Furthermore, a GC/MS method for the analysis of a synthetic mixture of underivatized urinary steroids is proposed. © 1997 by John Wiley & Sons, Ltd.     

Determination of phthalate esters in bottled water using dispersive liquid–liquid microextraction coupled with GC–MS

Dispersive liquid–liquid microextraction method was developed for the determination of the amount of phthalate esters in bottled drinking water samples and dispersive liquid–liquid microextraction samples were analyzed by GC–MS. Various experimental conditions influencing the extraction were optimized. Under the optimized conditions, very good linearity was observed for all analytes in a range between 0.05 and 150 μg/L with coefficient of determination (R²) between 0.995 and 0.999. The LODs based on S/N = 3 were 0.005–0.22 μg/L. The reproducibility of dispersive liquid–liquid microextraction was evaluated. The RSDs were 1.3–5.2% (n = 3). The concentrations of phthalates were determined in bottled samples available in half shell. To understand the leaching profile of these phthalates from bottled water, bottles were exposed to direct sunlight during summer (temperature from 34–57°C) and sampled at different intervals. Result showed that the proposed dispersive liquid–liquid microextraction is suitable for rapid determination of phthalates in bottled water and di‐n‐butyl, butyl benzyl, and bis‐2‐ethylhexyl phthalate compounds leaching from bottles up to 36 h. Thereafter, degradation of phthalates was observed.     

Effects of Centella asiatica extract on antioxidant status and liver metabolome of rotenone‐treated rats using GC–MS

Centella asiatica has been used as a culinary vegetable or medicinal herb. In this study, the hepatoprotective effect of the standardized extract of C. asiatica (ECa233) in rotenone‐treated rats was examined using a GC–MS‐based metabolomic approach. ECa233 contains >80% triterpenoids with a ratio of madecassoside to asiaticoside of 1.5(±0.5):1. Rats were randomly divided into three groups (with six rats/group): sham negative control, rotenone positive control and the ECa233 test group. Rats in the ECa233 group received 10 mg/kg ECa233 orally for 20 days, followed by 2.5 mg/kg intraperitoneal rotenone injection to induce toxicity before being sacrificed. Metabolomic analysis showed that supplementation of ECa233 protected rat liver against rotenone toxicity. Pipecolinic acid was one of the most important metabolites; its level was decreased in the rotenone group as compared with the control. Supplementation with ECa233 before administration of rotenone raised pipecolinic acid to levels intermediate between controls and rotenone alone. The metabolomics approach also helped discover a possible new genuine epimetabolite in the present work. Antioxidant tests revealed that ECa233 inhibited lipid peroxidation and increased catalase activities in liver tissue.     

Simultaneous determination of difenoconazole,trifloxystrobin and its metabolite trifloxystrobin acid residues in watermelon under field conditions by GC–MS/MS

An optimized quick, easy, cheap, effective, rugged and safe method for the simultaneous determination of difenoconazole, trifloxystrobin and its metabolite trifloxystrobin acid residues in watermelon and soil was developed and validated by gas chromatography with tandem mass spectrometry. The samples were extracted with acetonitrile (1% formic acid) and cleaned up by dispersive solid‐phase extraction with octadecylsilane sorbent. The limit of quantification of the method was 0.01 mg/kg, and the limit of detection was 0.003 mg/kg for all three analytes. The recoveries of the fungicides in watermelon, pulp and soil were 72.32–99.20% for difenoconazole, 74.68–87.72% for trifloxystrobin and 78.59–92.66% for trifloxystrobin acid with relative standard deviations of 1.34–14.04%. The dissipation dynamics of difenoconazole and trifloxystrobin in watermelon and soil followed the first‐order kinetics with half‐lives of 3.2–8.8 days in both locations. The final residue levels of difenoconazole and trifloxystrobin were below 0.1 mg/kg (maximum residue level [MRL] set by China) and 0.2 mg/kg (MRL set by European Union), respectively, in pulp samples collected 14 days after the last application. These results could help Chinese authorities to establish MRL of trifloxystrobin in watermelon and provide guidance for the safe and proper application of both fungicides on watermelon.     

Identification of cis/trans isomers of methyl ester and oxazoline derivatives of unsaturated fatty acids using GC–FTIR–MS

Identification of cis/trans isomers of unsaturated fatty acids cannot usually be achieved by GC-MS (gas chromatography-mass spectrometry) without reference substances. In this study a GC-FTIR-MS system (gas chromatography-Fourier transform-mass spectrometry) was used to identify fatty acid methyl esters (FAMEs) and differentiate between the cis/trans isomers. Besides methyl esters, 2-alkenyl-4,4-dimethyloxazoline derivatives (DMOX), which have been used to locate double bond positions of unsaturated fatty acids, were examined with respect to their suitability for cis/trans differentiation. A combined GC-FTIR-MS system with a wide band (4000–550 cm^?1) mercury cadmium telluride (MCT) detector was used in series and parallel to identify 31 reference unsaturated fatty acids, including 7 pairs of cis/trans isomers. Serum samples of healthy persons and commercially available fish oil were analyzed as examples of complex mixtures. Using splitless injection the detection limit for the less sensitive IR detector was 25 ng/μl in case of the weak cis and trans bands. In the FTIR spectra cis/trans isomers were identified by analysis of bands arising from C? H out-of-plane (oop) bending: for both the FAME and DMOX derivatives cis-1,2-disubstituted double bonds give a strong band near 720 cm^?1 and the corresponding trans isomers near 967 cm^?1. cis Isomers could be identified further by a band at 3012 cm^?1. With the combined data of the GC-FTIR-MS system it is now possible to identify polyunsaturated fatty acids with regard to the discrimination of cis/trans isomers.     

GC–MS with photoionization of cold molecules in supersonic molecular beams—Approaching the softest ionization method

A new type of photoionization ion source was developed for the ionization of cold molecules in supersonic molecular beams (named Cold PI). The system was based on a GC–MS with supersonic molecular beams and its fly‐through EI of cold molecules ion source (Cold EI) plus quadrupole mass analyzer. A continuously operated deuterium VUV photoionization lamp was added and placed above and between the supersonic nozzle and skimmer whereas the Cold EI ion source served only as a portion of the ion transfer ion optics. The supersonic nozzle and skimmer were voltage biased and the VUV light crossed the supersonic expansion about 10 mm from the nozzle. We obtained over three orders of magnitude enhancement in the relative abundance of the molecular ion of squalane in Cold PI versus in photoionization of this compound as a thermal compound. Accordingly, we also proved that standard photoionization is not as soft ionization method as previously perceived for large compounds. We found that Cold PI is as soft as and possibly softer than field ionization; thus, it could be the softest known ionization method. The ionization yield was about 200–300 times weaker than with Cold EI yet our limit of detection was about 200 femtogram in SIM mode for cholesterol and pyrene which is reasonable. Practically, all hydrocarbons gave only molecular ions with rather uniform response whereas alcohols gave some molecular ions plus major fragment ions particularly with a loss of water (similarly to field ionization). We tested Cold PI in the GC–MS analysis of diesel fuels and analyzed the time averaged data for group type information. We also found that we can analyze the diesel fuels by fast under 20‐s flow injection analysis in which the generated averaged mass spectrum of molecular ions only could serve for the characterization of fuels.     

Graphene as an efficient sorbent for the SPE of organochlorine pesticides in water samples coupled with GC–MS

The determination of organochlorine pesticides in water samples, which are harmful to humans, is very important for environmental risk assessment. Based on the excellent adsorption properties of graphene, an SPE coupled with GC–MS method for the monitoring of organochlorines (four hexachlorcyclohexanes and four dichlorodiphenyltrichloroethanes) was developed. Owing to the hydrophobic interaction and π–π stacking interaction between the analytes and graphene, the analytes quantitatively adsorbed onto the graphene‐based SPE cartridge were eluted by ethyl acetate for analysis. Several parameters influencing the analytical performance, such as the kind of elution, sample volume, reusability of the cartridge, have been investigated in detail. Under the optimal conditions, detection of limits of 1.95–9.38 ng/L, recoveries of 83.9–107.3% at two spiked concentration levels (0.1 and 10 ng/mL) and RSDs in the range of 2.9–7.4% for real water samples were obtained for all the analytes. This work reveals the great potential of graphene in sample preparation procedures.     

MDGC–MS: A powerful tool for enantioselective flavor analysis

This paper reports the differentiation between the enantiomers of theaspiranes and theaspirones, potent flavor compounds widely used in the flavor industry. Optically pure reference compounds of isomeric theaspiranes were obtained by enantioselective synthesis. Enantiomerically pure reference theaspirones were isolated from quince fruit; their absolute stereochemistry was assigned by CD spectroscopy. For both types of compounds the order of elution was elucidated by using authentic reference compounds. These data enabled the determination of the enantiomeric distribution of both types of compounds in a variety of plant tissues. Because of the complexity of the natural flavor isolates, compounds were identified by mass spectrometry after multidimensional gas chromatography employing a Sichromat 2 double oven chromatograph. After separation of the target compounds on the first, achiral, column (DB-5), they were transferred to a chiral column (C-Dex B) for determination of the enantiomeric distribution. Multiple ion detection (MID) enabled the determination of the enantiomeric distribution even for complex mixtures containing the target compounds at extremely low levels.     

Determination of cuticular and internal fatty acids of Chorthippus brunneus males and females using HPLC‐LLSD and GC–MS

Insects are of growing significance in veterinary medicine and human healthcare; therefore, an understanding of their biology is very important. The cuticular and internal fatty acid compositions of Chorthippus brunneus males and females have been studied for the first time. The lipids of males and females were separated into classes of compounds using high‐performance liquid chromatography with a laser light scattering detector. The free fatty acid (FFA) fractions obtained by HPLC were silylated and then analyzed by GC–MS. The cuticular lipids of males contained 15 saturated, four unsaturated with even‐numbered and two unsaturated with odd‐numbered carbon chains, FFAs ranging from C8 to C25. The major free fatty acids in males were C16 (20.8%), C18:2 (8.5%), C18:1 (32.9%) and C18 (24.4%). The cuticular lipids of females contained 17 saturated, four monounsaturated and two diunsaturated free fatty acids ranging from C8 to C30. The major cuticular fatty acids in females were C16 (25.1%), C18:2 (6.2%), C18:1 (23.7%) and C18:0 (33.2%). The internal FFAs of males consisted of 20 compounds ranging from C8 to C26. Four of these compounds were detected as major compounds: C16 (14.1%), C18:2 (21.6%), C18:1 (38.0%) and C18 (22.5%). Among 18 internal free fatty acids of females, C16 (22.3%), C18:2 (10.9%), C18:1 (40.2%) and C18 (20.5%) were the most abundant compounds. The following cuticular fatty acids present in the lipids of females were absent in the lipids of males: C26, C27 and C30. On the other hand, only C24 was absent from the cuticular lipids of females. Only C10 and C24 internal fatty acids present in the lipids of males were absent in the lipids of females. Copyright © 2016 John Wiley & Sons, Ltd.     

Comparative analysis of essential oils from eight herbal medicines with pungent flavor and cool nature by GC–MS and chemometric resolution methods

Systematic comparative research was conducted on essential oils from eight traditional Chinese medicines (TCM) of pungent flavor and cool nature because the essential oils are the main active ingredients of herbs of this kind. The work was based on their component analysis by gas chromatography–mass spectrometry (GC–MS), on their retention indices, as well as on chemometric resolution methods. A total of 144 compounds were tentatively identified, accounting for 69.0% to 91.8% of the total essential oils. It is worth noting that there are 67 compounds in at least three of these eight essential oils. Moreover, many biologically active compounds, such as hexanal, α‐pinene, camphene, β‐pinene, p‐cymene, limonene, eucalyptol, (Z)‐ocimene, γ‐terpinene, camphor, p‐menthone, 4‐terpineol, α‐terpineol, carvone, eugenol, caryophyllene, β‐farnesene, α‐curcumene, β‐selinene, δ‐cadinene, caryophyllene oxide, cedrol, n‐hexadecanoic acid, benzaldehyde, benzeneacetaldehyde, phthalic acid diisobutyl ester, linoleic acid, tetradecanoic acid, (Z,Z,Z)‐9,12,15‐octadecatrienoic acid, eucalyptol, pentadecanoic acid, hexadecanoic acid methyl ester, linoleic acid methyl ester, exist in at least four of the eight essential oils. These results might help us to understand why the eight herbs are all of pungent flavor and cool nature according to the theory of TCM, and may provide a useful chemical basis for future research on herbs of this kind.     

Nontargeted GC–MS approach for volatile profile of toasting in cherry,chestnut, false acacia,and ash wood

By using a nontargeted GC–MS approach, 153 individual volatile compounds were found in extracts from untoasted, light toasted and medium‐toasted cherry, chestnut, false acacia, as well as European and American ash wood, used in cooperage for aging wines, spirits and other beverages. In all wood types, the toasting provoked a progressive increase in carbohydrate derivatives, lactones and lignin constituents, along with a variety of other components, thus increasing the quantitative differences among species with the toasting intensity. The qualitative differences in the volatile profiles allow for identifying woods from cherry (being p‐anisylalcohol, p‐anisylaldehyde, p‐anisylacetone, methyl benzoate and benzyl salicylate detected only in this wood), chestnut (cis and trans whisky lactone) and false acacia (resorcinol, 3,4‐dimethoxyphenol, 2,4‐dihydroxy benzaldehyde, 2,4‐dihydroxyacetophenone, 2,4‐dihydroxypropiophenone and 2,4‐dihydroxy‐3‐methoxyacetophenone), but not those from ash, because of the fact that all compounds present in this wood are detected in at least one other. However, the quantitative differences can be clearly used to identify toasted ash wood, with tyrosol being most prominent, but 2‐furanmethanol, 3‐ and 4‐ethylcyclotene, α‐methylcrotonolactone, solerone, catechol, 3‐methylcatechol and 3‐hydroxybenzaldehyde as well. Regarding oak wood, its qualitative volatile profile could be enough to distinguish it from cherry and acacia woods, and the quantitative differences from chestnut (vanillyl ethyl ether, isoacetovanillone, butirovanillone, 1‐(5‐methyl‐2‐furyl)‐2‐propanone and 4‐hydroxy‐5,6‐dihydro‐(2H)‐pyran‐2‐one) and ash toasted woods. Copyright © 2014 John Wiley & Sons, Ltd.     

Pyrolysis of residual palm oil in spent bleaching clay by modified tubular furnace and analysis of the products by GC–MS

In this study, spent bleaching clay containing 26.6 wt.% of residual palm oil was pyrolyzed using a tubular furnace. Carboxylic acids ranging from C₉-C₁₈ and alkanes ranging from C₁₆-C₄₄ were the major classes of compounds found in the pyrolytic products analyzed using GC-MS. Significant amounts of monoaromatic compounds, alkenes, alcohols, ketones, aldehydes, esters, nitrogenated compounds, and polycyclic aromatic hydrocarbons (PAHs) were found in the bio-oil produced in this study. The bio-oil resulting from the pyrolysis process gave n-hexadecanoic acid as the major compound. Decomposition temperature of the adsorbed oil determined using TGA was found to be in the range of 573-683 K. Topographical and elemental analyses of the clay was done using SEM-EDX. The functional groups were determined using FTIR.     

Determination of phenolic compounds by MALDI–TOF and essential oil composition by GC–MS during three development stages of Origanum majorana L.

This study aimed to investigate the effect of the maturation process of sweet marjoram (Origanum majorana L.) on essential oil composition, the phenolic profile of ethanolic extract and their antioxidant capacities. The essential oil composition was studied at three stages of maturity by GC–MS. Thirty compounds were detected representing 100% of the total essential oil. p‐Menth‐1‐en‐4‐ol was the major compound (37.15–76.94%) followed by cyclohexanol‐3,3,5 trimethyl (5.41–15.99%) and α‐terpineol (0.94–11.34%). During the maturation process, an accumulation of oxygenated monoterpenes was observed. The phenolic composition was studied using matrix‐assisted laser desorption/ionization time of flight. The analysis showed the presence of short flavonoid monomers at all stages of maturation. The antioxidant capacity of ethanolic extracts and essential oils was evaluated using the DPPH assay, iron chelating power and reducing power assay. The highest phenolic content and antioxidant capacity were found at flowering stage. These findings on essential oil composition, phenolic profile and antioxidant capacity of O. majorana at three different stages of development provide more information on how these secondary metabolites are accumulated.     

Determination of endosulfan isomers and their metabolites in tap water and commercial samples using microextraction by packed sorbent and GC–MS

A simple, rapid, accurate and sensitive method using microextraction by packed sorbent (MEPS) followed by GC–MS has been pursued for the determination of organochlorine insecticide endosulfan isomers (α and β) and their metabolites (ether, lactone and sulfate). MEPS is a miniaturised version of SPE employing C₁₈ packing material. It is very efficient technique as it employs as low as 10 μL of sample volume. The distinct feature of MEPS is the magnitude of the elution volume that could be directly injected to GC system. Various parameters such as extraction cycles, washing solvent, elution solvent, elution volume and pH, which influenced the MEPS performance, were tested and optimised. The calibration curves were obtained in the concentration range 1–500 ng/mL. The results showed a close correlation coefficient (R² > 0.991) for all analytes in the calibration range studied. The LOD and LOQ obtained for GC–MS under selected ion monitoring acquisition are between 0.0038–0.01 and 0.0125–0.033 ng/mL, respectively. The developed method is applicable for the quantification of these compounds in tap water and commercial samples. This method has been shown to be selective as no interferences from endogenous substances were detected by analysis. This method not only decreases sample preparation time but is cheaper, eco‐friendly and easier to perform compared to traditional techniques.     

Analysis of polybrominated diphenyl ethers in sewage sludge by matrix solid‐phase dispersion and isotope dilution GC–MS

A method for the determination of 14 polybrominated diphenyl ethers (PBDEs) in sludge from wastewater treatment plants is presented. PBDEs were extracted by matrix solid‐phase dispersion assisted by sonication and determined by isotope dilution gas chromatography with electron impact mass spectrometric detection in the selected ion monitoring mode, using labelled ¹³C‐PBDEs as internal standards. The limits of detection and quantification for the tri‐ to hepta‐BDEs were in the range of 0.05 to 0.5 ng/g dry weight and 0.15 to 1.8 ng/g dry weight, respectively, and 1.6 ng/g dry weight and 5.6 ng/g dry weight for deca‐BDE‐209. The proposed analytical method was applied to determine PBDE levels in sewage sludge samples collected from 19 water treatment plants located in the province of Madrid (Spain). In all of the examined samples, BDE‐100 and BDE‐154 were the main compounds found with a mean concentration of 3.9 and 2.0 ng/g, respectively. PBDEs were detected in all of the samples, and their total concentrations not considering BDE‐209 were between 3.9 and 23.0 ng/g dry weight. The dominant PBDE congener in sewage sludge was BDE‐209, which constituted 38.7 to 97.3% of the total, and showed concentration levels ranging from 8.1 to 717.2 ng/g dry weight.     

Comparative analysis of volatile constituents in Citrus Reticulata Blanco using GC–MS and alternative moving window factor analysis

The similarities and differences of essential oil components in Album Citri Reticulatae (ACR), Cylindricae Citri Reticulatae (CCR), Folium Citri Reticulatae (FCR), Exocarpium Citri Grandis (ECG), Pericarpium Citri Reticulatae Viride (PCRV) and Pericarpium Citri Reticulatae (PCR) were investigated by GC–MS combined with a chemometric method named alternative moving window factor analysis (AMWFA). And temperature‐programmed retention indices (PTRIs) were used together with mass spectra for identification of the essential oil components. In essential oils of ACR, CCR, FCR, ECG, PCRV and PCR, 28, 26, 61, 62, 52 and 48 components were determined representing 93.13, 94.44, 93.53, 87.67, 99.03 and 98.03% of the total relative content, respectively. Also, the essential oils significantly differed both qualitatively and quantitatively. There were 14 common components among ACR, CCR, FCR, ECG, PCRV and PCR, their abundance varied in the ranges from 32.39% in FCR to 94.66% in PCRV. The results obtained may be helpful to the further study of pharmacological activity for their potential utilization as therapeutical agents.     

GC–MS combined with chemometric techniques for the quality control and original discrimination of Curcumae longae rhizome: Analysis of essential oils

Curcumae longae rhizome is a widely used traditional herb in many countries. Various geographical origins of this herb might lead to diversity or instability of the herbal quality. The objective of this work was to establish the chemical fingerprints for quality control and find the chemical markers for discriminating these herbs from different origins. First, chemical fingerprints of essential oil of 24 C. longae rhizome from four different geographical origins in China were determined by GC–MS. Then, pattern recognition techniques were introduced to analyze these abundant chemical data in depth; hierarchical cluster analysis was used to sort samples into groups by measuring their similarities, and principal component analysis and partial least‐squares discriminate analysis were applied to find the main chemical markers for discriminating these samples. Curcumae longae rhizome from Guangxi province had the highest essential oil yield (4.32 ± 1.45%). A total of 46 volatile compounds were identified in total. Consistent results were obtained to show that C. longae rhizome samples could be successfully grouped according to their origins, and turmerone, ar‐turmerone, and zingiberene were the characteristic components for discriminating these samples of various geographical origins and for quality control. This finding revealed that fingerprinting analysis based on GC–MS coupled with chemometric techniques could provide a reliable platform to discriminate herbs from different origins, which is a benefit for quality control.     

Analysis of vaporous contaminants including low‐volatility analytes permeating textiles at room temperature using headspace solid‐phase microextraction GC–MS

Detection of toxic vapors permeating textiles is an important measure of the efficacy of a protective garment. Here, we demonstrate a method to detect and analyze contaminant vapors as they permeate through cotton textiles. Specifically, we show how this method can be improved upon by the incorporation of solid‐phase microextraction into the sampling process, thereby allowing low‐volatility analytes to be sampled at room temperature without significantly influencing the concentration of the contaminant in the headspace. Furthermore, this technique can be extended to other applications in the development of barrier materials as it lends itself to kinetics as well as direct comparison of materials' total chemical permeation. Copyright © 2015 John Wiley & Sons, Ltd.