Dithieno[2,3‐d:2',3'‐d']benzo[1,2‐b:4,5‐b']dithiophene (DTBDAT)‐based copolymers for high‐performance organic solar cells

P(BDT‐TCNT) and P(DTBDAT‐TCNT) , which has an extended conjugation length, were designed and synthesized for applications in organic solar cell (OSCs). The solution absorption maxima of P(DTBDAT‐TCNT) with the extended conjugation were red‐shifted by 5–15 nm compared with those of P(BDT‐TCNT) . The optical band gaps and highest occupied molecular orbital (HOMO) energy levels of both P(BDT‐TCNT) and P(DTBDAT‐TCNT) were similar. The structure properties of thin films of these materials were characterized using grazing‐incidence wide‐angle X‐ray scattering and tapping‐mode atomic force microscopy, and charge carrier mobilities were characterized using the space‐charge limited current method. OSCs were formed using [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as the electron acceptor and 3% diphenylether as additive suppress aggregation. OSCs with P(BDT‐TCNT) as the electron donor exhibited a power conversion efficiency (PCE) of 4.10% with a short‐circuit current density of J_SC = 9.06 mA/cm², an open‐circuit voltage of V_OC = 0.77 V, and a fill factor of FF = 0.58. OSCs formed using P(DTBDAT‐TCNT) as the electron donor layer exhibited a PCE of 5.83% with J_SC = 12.2 mA/cm², V_OC = 0.77 V, and FF = 0.62. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3182–3192     

Thiophene π bridge effect on bulky side‐chained benzodithiophene‐based photovoltaic polymers

Recently, we have used terthiophene side chain to modify benzo[1,2‐b:4,5‐b′]dithiophene (BDT) to form novel building block for BDT polymers. In this paper, this building block is used to copolymerized with thieno[3,4‐c]pyrrole‐4,6‐dione (TPD) and thieno[3,4‐b]thiophene (TT). This building block and TPD‐ or TT‐based polymers (P1 and P3) show high open circuit voltage (V_OC) (ca. 0.9–0.95 V) and low energy loss (E_g–eV_OC) in solar cells devices compared with similar polymers without bulky side chain. We further introduce thiophene π bridge into these polymers backbone to form two other polymers (P2 and P4). We find this thiophene π bridge does contribute to this bulky side chained benzodithiophene polymer photovoltaic performances, especially for power conversion efficiencies (PCEs). The polymer solar cells (PSCs) performances are moderate in this article due to the serious aggregation in the PSCs active layer. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1615–1622     

A Photoelectrochemical Solar Cell Consisting of a Cadmium Sulfide Photoanode and a Ruthenium–2,2′‐Bipyridine Redox Shuttle in a Non‐aqueous Electrolyte

A photoelectrochemical (PEC) cell consisting of an n‐type CdS single‐crystal electrode and a Pt counter electrode with the ruthenium–2,2′‐bipyridine complex [Ru(bpy)₃]^2+/3+ as the redox shuttle in a non‐aqueous electrolyte was studied to obtain a higher open‐circuit voltage (V_OC) than the onset voltage for water splitting. A V_OC of 1.48 V and a short‐circuit current (I_SC) of 3.88 mA cm^?2 were obtained under irradiation by a 300 W Xe lamp with 420–800 nm visible light. This relatively high voltage was presumably due to the difference between the Fermi level of photo‐irradiated n‐type CdS and the redox potential of the Ru complex at the Pt electrode. The smooth redox reaction of the Ru complex with one‐electron transfer was thought to have contributed to the high V_OC and I_SC. The obtained V_OC was more than the onset voltage of water electrolysis for hydrogen and oxygen generation, suggesting prospects for application in water electrolysis.     

Phenanthrene‐Fused‐Quinoxaline as a Key Building Block for Highly Efficient and Stable Sensitizers in Copper‐Electrolyte‐Based Dye‐Sensitized Solar Cells

Dye‐sensitized solar cells (DSSCs) based on Cu^II/I bipyridyl or phenanthroline complexes as redox shuttles have achieved very high open‐circuit voltages (V_OC, more than 1 V). However, their short‐circuit photocurrent density (J_SC) has remained modest. Increasing the J_SC is expected to extend the spectral response of sensitizers to the red or NIR region while maintaining efficient electron injection in the mesoscopic TiO₂ film and fast regeneration by the Cu^I complex. Herein, we report two new D‐A‐π‐A‐featured sensitizers termed HY63 and HY64 , which employ benzothiadiazole (BT) or phenanthrene‐fused‐quinoxaline (PFQ), respectively, as the auxiliary electron‐withdrawing acceptor moiety. Despite their very similar energy levels and absorption onsets, HY64 ‐based DSSCs outperform their HY63 counterparts, achieving a power conversion efficiency (PCE) of 12.5 %. PFQ is superior to BT in reducing charge recombination resulting in the near‐quantitative collection of photogenerated charge carriers.     

Theoretical Prediction on Photovoltaic Properties of 4Cl‐BPPQ/PC61BM System via Density Functional Theory Calculations

Designing and synthesizing high‐performable electron donor materials are very important for fabricating organic solar cell devices with high power conversion efficiency (PCE). In this work, quantum chemical and molecular dynamics calculations coupled with the Marcus‐Hush charge transfer model were used to investigate the photovoltaic properties of 4Cl‐BPPQ/PC₆₁BM. Results reveal that 4Cl‐BPPQ/PC₆₁BM system theoretically possesses a large open‐circuit voltage (1.29 V), high fill factor (0.90), and over 9% PCE. Moreover, calculations also reveal that the 4Cl‐BPPQ/PC₆₁BM system has a middle‐sized exciton binding energy (0.492 eV), but relatively small charge‐dissociation and charge‐recombination reorganization energies (0.345 eV and 0.355 eV). Based on the 4Cl‐BPPQ/PC₆₁BM complex, the charge‐dissociation rate constant, k_dis, is estimated to be as large as 6.575×10¹² s^?1, while the charge‐recombination one, k_rec, is very small (<1.0 s^?1) under the same condition due to the very small driving force (ΔG_rec=?1.900 eV). In addition, by means of an amorphous cell containing one hundred 4Cl‐BPPQ molecules, the hole carrier mobility of 4Cl‐BPPQ solid is estimated as high as 3.191×10^?3 cm²·V^?1·s^?1. In brief, our calculation shows that 4Cl‐BPPQ/PC₆₁BM system is a very promising organic solar cell system, and is worth of making further device research by experiments.     

Controlling Interfacial Charge Transfer and Fill Factors in CuO‐based Tandem Dye‐Sensitized Solar Cells

We designed and synthesized a series of novel electron‐accepting zinc(II)phthalocyanines (ZnPc) and probed them in p‐type dye sensitized solar cells (p‐DSSCs) by using CuO as photocathodes. By realizing the right balance between interfacial charge separation and charge recombination, optimized fill factors (FFs) of 0.43 were obtained. With a control over fill factors in p‐DSSCs in hand we turned our attemtion to t‐DSSCs, in which we combined for the first time CuO‐based p‐DSSCs with TiO₂‐based n‐DSSCs using ZnPc and N719. In the resulting t‐DSSCs, the V_OC of 0.86 V is the sum of those found in p‐ and n‐DSSCs, while the FF remains around 0.63. It is only the smaller J_scs in t‐DSSCs that limits the efficiency to 0.69 %.     

A New Small-Molecule Donor Containing Non-Fused Ring π-Bridge Enables Efficient Organic Solar Cells with High Open Circuit Voltage and Low Acceptor Content

To achieve high open-circuit voltage (V_oc) and low acceptor content, the molecular design of a small-molecule donor with low energy loss (E_loss) is very important for solution-processable organic solar cells (OSCs). Herein, we designed and synthesized a new coplanar A−D−A structured organic small-molecule semiconductor with non-fused ring structure π-bridge, namely B2TPR , and applied it as donor material in OSCs. Owing to the strong electron-withdrawing effect of the end group and the coplanar π-bridge, B2TPR exhibits a low-lying highest occupied molecular orbital and strong crystallinity. Furthermore, benefiting from the coplanar molecular skeleton, the high hole mobility, balanced charge transport and reduced recombination were achieved, leading to a high fill factor (FF). The OSCs based on B2TPR : PC₇₁BM blend film (w/w=1 : 0.35) demonstrates a moderate power conversion efficiency (PCE) of 7.10 % with a remarkable V_oc of 0.98 V and FF of 64 %, corresponding to a low fullerene content of 25.9 % and a low E_loss of 0.70 eV. These results demonstrate the great potential of small-molecule with structure of B2TPR for future low-cost organic photovoltaic applications.     

13.34 % Efficiency Non‐Fullerene All‐Small‐Molecule Organic Solar Cells Enabled by Modulating the Crystallinity of Donors via a Fluorination Strategy

Non‐fullerene all‐small‐molecule organic solar cells (NFSM‐OSCs) have shown potential as OSCs, owing to their high purity, easy synthesis and good reproducibility. However, challenges in the modulation of phase separation morphology have limited their development. Herein, two novel small molecular donors, BTEC‐1F and BTEC‐2F, derived from the small molecule DCAO3TBDTT, are synthesized. Using Y6 as the acceptor, devices based on non‐fluorinated DCAO3TBDTT showed an open circuit voltage (V_oc) of 0.804 V and a power conversion efficiency (PCE) of 10.64 %. Mono‐fluorinated BTEC‐1F showed an increased V_oc of 0.870 V and a PCE of 11.33 %. The fill factor (FF) of di‐fluorinated BTEC‐2F‐based NFSM‐OSC was improved to 72.35 % resulting in a PCE of 13.34 %, which is higher than that of BTEC‐1F (61.35 %) and DCAO3TBDTT (60.95 %). To our knowledge, this is the highest PCE for NFSM‐OSCs. BTEC‐2F had a more compact molecular stacking and a lower crystallinity which enhanced phase separation and carrier transport.     

Potential of Nonfullerene Small Molecules with High Photovoltaic Performance

Over the past decades, fullerene derivatives have become the most successful electron acceptors in organic solar cells (OSCs) and have achieved great progress, with power conversion efficiencies (PCEs) of over 11 %. However, fullerenes have some drawbacks, such as weak absorption, limited energy‐level tunability, and morphological instability. In addition, fullerene‐based OSCs usually suffer from large energy losses of over 0.7 eV, which limits further improvements in the PCE. Recently, nonfullerene small molecules have emerged as promising electron acceptors in OSCs. Their highly tunable absorption spectra and molecular energy levels have enabled fine optimization of the resulting devices, and the highest PCE has surpassed 12 %. Furthermore, several studies have shown that OSCs based on small‐molecule acceptors (SMA) have very efficient charge generation and transport efficiency at relatively low energy losses of below 0.6 eV, which suggests great potential for the further improvement of OSCs. In this focus review, we analyze the challenges and potential of SMA‐based OSCs and discuss molecular design strategies for highly efficient SMAs.     

Molecular Engineering of Simple Phenothiazine‐Based Dyes To Modulate Dye Aggregation,Charge Recombination,and Dye Regeneration in Highly Efficient Dye‐Sensitized Solar Cells

A series of simple phenothiazine‐based dyes, namely, TP , EP , TTP , ETP , and EEP have been developed, in which the thiophene (T), ethylenedioxythiophene (E), their dimers, and mixtures are present to modulate dye aggregation, charge recombination, and dye regeneration for highly efficient dye‐sensitized solar cell (DSSC) applications. Devices sensitized by the dyes TP and TTP display high power conversion efficiencies (PCEs) of 8.07 (J_sc=15.2 mA cm^?2, V_oc=0.783 V, fill factor (FF)=0.679) and 7.87 % (J_sc=16.1 mA cm^?2, V_oc=0.717 V, FF=0.681), respectively; these were measured under simulated AM 1.5 sunlight in conjunction with the I^?/I₃^? redox couple. By replacing the T group with the E unit, EP ‐based DSSCs had a slightly lower PCE of 7.98 % with a higher short‐circuit photocurrent (J_sc) of 16.7 mA cm^?2. The dye ETP , with a mixture of E and T, had an even lower PCE of 5.62 %. Specifically, the cell based on the dye EEP , with a dimer of E, had inferior J_sc and V_oc values and corresponded to the lowest PCE of 2.24 %. The results indicate that the photovoltaic performance can be finely modulated through structural engineering of the dyes. The selection of T analogues as donors can not only modulate light absorption and energy levels, but also have an impact on dye aggregation and interfacial charge recombination of electrons at the interface of titania, electrolytes, and/or oxidized dye molecules; this was demonstrated through DFT calculations, electrochemical impedance analysis, and transient photovoltage studies.     

Designing Nonfullerene Acceptors with Oligo(Ethylene Glycol) Side Chains: Unraveling the Origin of Increased Open-Circuit Voltage and Balanced Charge Carrier Mobilities

Despite the recent rapid development of organic solar cells (OSCs), the low dielectric constant (ϵ_r=3–4) of organic semiconducting materials limits their performance lower than inorganic and perovskite solar cells. In this work, we introduce oligo(ethylene glycol) (OEG) side chains into the dicyanodistyrylbenzene-based non-fullerene acceptors (NIDCS) to increase its ϵ_r up to 5.4. In particular, a NIDCS acceptor bearing two triethylene glycol chains (NIDCS-EO3) shows V_OC as high as 1.12 V in an OSC device with a polymer donor PTB7, which is attributed to reduced exciton binding energy of the blend film. Also, the larger size grain formation with well-ordered stacking structure of the NIDCS-EO3 blend film leads to the increased charge mobility and thus to the improved charge mobility balance, resulting in higher J_SC, FF, and PCE in the OSC device compared to those of a device using the hexyl chain-based NIDCS acceptor (NIDCS-HO). Finally, we fabricate NIDCS-EO3 devices with various commercial donors including P3HT, DTS-F, and PCE11 to show higher photovoltaic performance than the NIDCS-HO devices, suggesting versatility of NIDCS-EO3.     

Dyes and Redox Couples with Matched Energy Levels: Elimination of the Dye‐Regeneration Energy Loss in Dye‐Sensitized Solar Cells

In dye‐sensitized solar cells (DSSCs), a significant dye‐regeneration force (ΔG_reg⁰≥0.5 eV) is usually required for effective dye regeneration, which results in a major energy loss and limits the energy‐conversion efficiency of state‐of‐art DSSCs. We demonstrate that when dye molecules and redox couples that possess similar conjugated ligands are used, efficient dye regeneration occurs with zero or close‐to‐zero driving force. By using Ru(dcbpy)(bpy)₂²⁺ as the dye and Ru(bpy)₂(MeIm)₂^3+//2+ as the redox couple, a short‐circuit current (J_sc) of 4 mA cm^?2 and an open‐circuit voltage (V_oc) of 0.9 V were obtained with a ΔG_reg⁰ of 0.07 eV. The same was observed for the N3 dye and Ru(bpy)₂(SCN)₂^1+/0 (ΔG_reg⁰=0.0 eV), which produced an J_sc of 2.5 mA cm^?2 and V_oc of 0.6 V. Charge recombination occurs at pinholes, limiting the performance of the cells. This proof‐of‐concept study demonstrates that high V_oc values can be attained by significantly curtailing the dye‐regeneration force.     

A Rutile TiO2 Electron Transport Layer for the Enhancement of Charge Collection for Efficient Perovskite Solar Cells

Interfacial charge collection efficiency has demonstrated significant effects on the power conversion efficiency (PCE) of perovskite solar cells (PSCs). Herein, crystalline phase‐dependent charge collection is investigated by using rutile and anatase TiO₂ electron transport layer (ETL) to fabricate PSCs. The results show that rutile TiO₂ ETL enhances the extraction and transportation of electrons to FTO and reduces the recombination, thanks to its better conductivity and improved interface with the CH₃NH₃PbI₃ (MAPbI₃) layer. Moreover, this may be also attributed to the fact that rutile TiO₂ has better match with perovskite grains, and less trap density. As a result, comparing with anatase TiO₂ ETL, MAPbI₃ PSCs with rutile TiO₂ ETL delivers significantly enhanced performance with a champion PCE of 20.9 % and a large open circuit voltage (V_OC) of 1.17 V.     

Polymer Electron Acceptors Based on Fluorinated Isoindigo Unit for Polymer Solar Cells

Most of efficient polymer electron acceptors for polymer solar cells (PSCs) are based on naphthalene diimide or perylene diimide as the electron deficient building block. In this paper, for the first time, we report polymer electron acceptors based on fluorinated isoindigo (F‐IID) as the electron deficient building block. We synthesized two polymer electron acceptors consisting of alternating F‐IID unit and thiophene/selenophen unit. They show low‐lying LUMO/HOMO energy levels of –3.69/–5.69 eV, high electron mobilities of 1.31×10^–5 cm²·V^–1·s^–1 and broad absorption spectra with the optical bandgap of 1.61 eV. PSC devices using the two F‐IID‐based polymers as polymer electron acceptors show encouraging power conversion efficiencies (PCEs) of up to 1.50% with an open‐circuit voltage (V_OC) of 0.97 V, a short‐circuit current density (J_SC) of 2.91 mA·cm^–2, and a fill factor (FF) of 53.2%. This work suggests a new kind of polymer electron acceptors based on F‐IID unit.     

The Origin of Higher Open‐Circuit Voltage in Zn‐Doped TiO2 Nanoparticle‐Based Dye‐Sensitized Solar Cells

Zn‐doped anatase TiO₂ nanoparticles are synthesized by a one‐step hydrothermal method. Detailed electrochemical measurements are undertaken to investigate the origin of the effect of Zn doping on the performance of dye‐sensitized solar cells (DSSCs). It is found that incorporation of Zn²⁺ into an anatase lattice elevates the edge of the conduction band (CB) of the photoanodes and the Fermi level is shifted toward the CB edge, which contributes to the improvement in open‐circuit voltage (V_OC). Charge‐density plots across the cell voltage further confirm the increase in the CB edge in DSSCs directly. Photocurrent and transient photovoltage measurements are employed to study transport and recombination dynamics. The electron recombination is accelerated at higher voltages close to the CB edge, thus leading to a negative effect on the V_OC.     

Modification of Hole Transport Layers for Fabricating High Performance Non‐fullerene Polymer Solar Cells

Interfacial engineering is expected to be a feasible strategy to improve the charge transport properties of the hole transport layer (HTL), which is of crucial importance to boost the device performance of organic solar cells (OSCs). In this study, two types of alcohol soluble materials, 2,3,5,6‐tetrafluoro‐7,7,8,8‐tetracyanoquinodimethane (F₄‐TCNQ) and di‐tetrabutylammoniumcis–bis(isothiocyanato)bis (2,2’‐bipyridyl‐4,4’‐dicarboxylato) ruthenium(II) (N719) dye were selected as the dopant for HTL. The doping of F₄‐TCNQ and N719 dye in poly (ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) with and without integrating a graphene quantum‐dots (G‐QDs) layer has been explored in poly[[2,6′‐4‐8‐di(5‐ethylhexylthienyl)benzo[1,2‐b:3,3‐b]dithiophene][3‐fluoro‐2[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thio‐phenediyl:(2,2′‐((2Z,2′Z)‐(((4,4,9, 9‐tetrakis(4‐hexylphenyl)‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐2,7‐diyl)bis(4‐((2‐ethylhexyl)oxy)thiophene‐5,2‐diyl))bis(methanylylidene))bis(5,6‐difluoro‐3‐oxo‐2,3‐dihydro‐1H‐indene‐2,1‐diylidene))dimalononitrile (PTB7‐Th:IEICO‐4F) OSCs. The power conversion efficiency of the non‐fullerene OSCs has been increased to 10.12% from 8.84%. The influence of HTL modification on the nano‐morphological structures and photophysical properties is analyzed based on the comparative studies performed on the control and modified devices. The use of chemical doping and bilayer strategy optimizes the energy level alignment, nanomorphology, hole mobility, and work‐function of HTL, leading to considerable reduction of the leakage current and recombination losses. Our work demonstrates that the doping of HTL and the incorporation of G‐QDs layer to constitute a bilayer HTL is an promising strategy to fabricate high performance non‐fullerene polymer solar cells     

Synthesis and Photovoltaic Properties of Ester Group Functionalized Polythiophene Derivatives

To increase the open circuit voltage (V_OC) of polymer solar cells (PSCs) based on polythiophene, two new ester group functionalized polythiophene derivatives, PCTDT and PCTBDT, were designed and synthesized via alternating copolymerization of thiophene‐3‐carboxylate (CT) with the 2,2′‐bithiophene (DT) and benzodithiophene (BDT) units, respectively. The resulting copolymers exhibited broad and strong absorptions in the visible region, which was similar to that of the commonly used poly(3‐hexylthiophene) (P3HT). Through cyclic voltammetry measurements, it was found that both copolymers showed lower HOMO energy levels (−5.27 eV for PCTDT and −5.36 eV for PCTBDT) than that of P3HT (−5.03 eV), indicating that the HOMO energy level could be efficiently reduced by introducing the ester group into the polymer side chain. Photovoltaic properties of the copolymers blended with [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) as electron acceptor were investigated. The obtained two devices possessed both relatively large short circuit current (I_SC) and higher V_OC than that of P3HT:PCBM blend. For PCTBDT:PCBM blend, a power conversion efficiency (PCE) up to 2.32%, an I_SC of 6.94 mA · cm⁻², and a V_OC of 0.80 V were observed while PCTDT:PCBM system demonstrated a PCE of 1.75% with a V_OC of 0.68 V.

     

A p‐Type NiO‐Based Dye‐Sensitized Solar Cell with an Open‐Circuit Voltage of 0.35 V

In tandem : Employing a molecular dyad and a cobalt‐based electrolyte gives a threefold‐increase in open‐circuit voltage (V_OC) for a p‐type NiO device (V_OC=0.35 V), and a fourfold better energy conversion efficiency. Incorporating these improvements in a TiO₂/NiO tandem dye‐sensitized solar cell (TDSC), results in a TDSC with a V_OC=0.91 V (see figure; CB=conductance band, VB= valence band).

     

Enhanced efficiency of ternary organic solar cells by doping a polymer material in P3HT:PC61BM

Doping a low‐bandgap polymer material (PDTBDT‐DTNT) as a complementary electron donor in poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C₆₁‐butyricacid methyl ester (PC₆₁BM) blend is experimented to improve the power conversion efficiency (PCE) of organic solar cells (OSCs). The PCE of OSCs was increased from 3.19% to 3.75% by doping 10 wt% PDTBDT‐DTNT, which was 17.55% higher than that of the OSCs based on binary blend of P3HT:PC₆₁BM (host cells). The short‐circuit current density (J_sc) was increased to 10.11 mA·cm⁻² compared with the host cells. Although the PCE improvement could partly be attributed to more photon harvest for complementary absorption of 2 donors by doping appropriate PDTBDT‐DTNT, the promotion of charge separation and transport as well as the suppression of charge recombination due to a matrix of cascade energy levels is also important. And the better morphology of the active layer films is beneficial to the optimized performance of ternary devices.     

Benzo[2,1‐b;3,4‐b′]dithiophene‐based low‐bandgap polymers for photovoltaic applications

The synthesis of four alternating copolymers using benzo[2,1‐b;3,4‐b′]dithiophene (BDP) as the common donor unit is presented. Before the synthesis, theoretical calculations that we performed predicted that the incorporation of BDP, which consists of fused dithiophene units with a benzene ring, into these polymers would produce a low‐lying highest occupied molecular orbital (HOMO) energy level. Low‐lying HOMO levels are desirable to produce high open circuit voltages (V_OC) in organic bulk heterojunction (BHJ) photovoltaic devices. The polymers' structural characterization, as well as the preliminary results of their performance in BHJ devices, using (6,6)‐phenyl C₆₁‐butyric acid methyl ester as the electron acceptor, is presented. The V_OC values follow the expected trend: increasing with decreasing HOMO level of the polymer. High V_OC values of 0.81 and 0.82 V have been obtained from two polymers: PBDPBT and PBDPDPP. The initial power conversion efficiency achieved in these unoptimized devices was 1.11% because of relatively low J_SC values. The variation observed in the J_SC values between the four polymers is discussed. Device performance is expected to increase with optimization of processing conditions for the devices. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011