光梳主动滤波放大实现锶原子光钟二级冷却光源

提出一种结合注入锁定技术的主动滤波放大方法,将光梳直接注入锁定至光栅外腔半导体激光器,产生窄线宽激光光源,该光源可以用于锶原子光钟二级冷却.实验中,将中心波长为689 nm,带宽为10 nm的光梳种子光源注入689 nm光栅式外腔半导体激光器,通过半导体增益光谱与半导体光栅外腔,从飞秒光梳的多个纵模梳齿中挑选出一个纵模模式来进行增益放大,再通过模式竞争,实现单纵模连续光输出;同时,光梳的重复频率锁定在线宽为赫兹量级的698 nm超稳激光光源上,因此,注入锁定后输出的窄线宽激光也继承了超稳激光光源的光谱特性.利用得到的输出功率为12 mW的689 nm窄线宽激光光源实现了88Sr原子光钟的二级冷却过程,最终获得温度为3μK,原子数约为5×10~6的冷原子团.该方法可拓展至原子光钟其他光源的获得,从而实现原子光钟的集成化和小型化.     

利用光频梳提高台阶高度测量准确度的方法

提出一种利用光频梳和可调谐半导体激光器提高台阶高度测量准确度的方法. 通过将可调谐激光器锁定至光频梳,可对激光器的输出波长进行精确锁定与测量.基于可调合成波长链原理,利用锁定后的半导体激光器构建了一套台阶高度测量方案,该方案可消除合成波长误差对台阶高度测量不确定度的影响. 采用一台可调谐半导体激光器和光频梳进行了5000 s的连续锁定实验, 结果表明,锁定后的可调谐半导体激光器的频率稳定度达 1.8×10^-12.该方法的理论测量不确定度约为7.9 nm, 且测量结果可溯源至时间频率基准.     

Optical locking of two semiconductor lasers through high-order Brillouin Stokes components in optical fiber

A novel technique for optical injection locking of two semiconductor lasers through high-order Brillouin Stokes components in optical fiber is proposed and experimentally demonstrated. The configuration potentially provides microwave signals generation at manifold Brillouin frequency without high-frequency external modulator and generator. Significant narrowing of the locked slave semiconductor laser linewidth was recorded.     

用于激光冷却的半导体激光器大频差边模注入锁定的理论及实验研究

利用注入锁定技术实现了与自由运转频率相差1300?GHz的大功率半导体激光器的边模注入 锁定.实验上利用饱和吸收谱和光学外差拍方法详细研究了锁定后主从激光器之间的相干转 移特性,并测量了注入光功率与锁频范围的关系和注入锁定模式建立过程,与利用带注入项 的多模速率方程得到的边模注入锁定的范围相吻合.理论上计算了实现边模注入锁定所满足 的注入光阈值条件,并作了实验验证. 关键词：     

基于飞秒光频梳的压电陶瓷闭环位移控制系统

利用飞秒光频梳、外腔可调谐半导体激光器和法布里-珀罗干涉仪建立了一套压电陶瓷亚纳米级闭环位移控制系统. 将可调谐半导体激光器锁定至光频梳, 通过精确调谐光频梳的重复频率, 实现了半导体激光器在其工作频率范围内的精密调谐. 利用Pound-Drever-Hall锁定技术将带有压电陶瓷的法布里-珀罗腔锁定至半导体激光器, 进而通过频率发生系统控制压电陶瓷产生亚纳米级分辨率的位移. 实验研究发现锁定至光频梳后可调谐半导体激光器1 s的Allan标准偏差为1.68×10^-12, 将其在30.9496 GHz范围内进行连续闭环调谐, 可获得压电陶瓷的位移行程约为4.8 μm; 以3.75 Hz的步长扫描光频梳的重复频率, 实现了压电陶瓷的450 pm闭环位移分辨率并测定了压电陶瓷的磁滞特性曲线. 该系统不存在非线性测量误差, 且激光频率及压电陶瓷位移均溯源至铷钟频率源. 关键词： 光频梳 压电陶瓷 法布里-珀罗腔 可调谐半导体激光器     

Injection locked multi-section gain-coupled dual mode DFB laser for terahertz generation

A dual mode multi-section gain-coupled distributed feedback laser with tunable mode spacing is subharmonically injection locked at 0.315 THz. The injected signal consists of an optical comb with harmonics 35 GHz apart and a bandwidth of approximately 1.9 THz. The optical comb is a result of strong four-wave mixing in a highly-nonlinear dispersion-shifted fiber. In order to observe locking of the multi-section laser, the output is optically downconverted to RF frequencies using the same optical comb. The locked multi-section DFB laser is a coherent and tunable optical source suitable for continuous-wave terahertz generation systems.     

Precision phase control of an ultrawide-bandwidth femtosecond laser: a network of ultrastable frequency marks across the visible spectrum

We demonstrate that the stability of the current optical frequency comb generated by a Kerr-lens mode-locked femtosecond laser is limited by the microwave reference used for phase locking the comb spacing. Hence we implement precision frequency/phase control of the entire comb to the fundamental and second-harmonic frequencies of a stable cw laser without any external microwave reference. The stability of a cw iodine-stabilized laser is transferred to millions of comb lines (with an instability of 3 x 10(-13)) covering more than one octave of the optical frequency spectrum. In addition, the mode spacing of the comb can be used as a stable microwave frequency derived directly from a stable optical oscillator.     

Amplitude-squeezed, frequency-modulated, tunable, diode-laser-based source for sub-shot-noise FM spectroscopy

We have developed a frequency-modulated, tunable, amplitude-squeezed, diode-laser-based source and used it to perform FM spectroscopy on rubidium. The setup consists of a free-running diode laser injection locked by a frequency-stabilized, current-modulated diode laser. The injection-locked slave laser beam adopted the frequency spectrum of the master laser beam while rejecting residual AM in the master laser beam by more than 50 dB. Injection locking also enhanced amplitude squeezing in the slave laser beam by suppressing uncorrelated longitudinal sidemodes. The noise floor of the measurement was 0.8 dB below the shot-noise level.     

Injection locking of a diode laser locked to a Zeeman frequency stabilized laser oscillator

We describe the design and performance of an injection-locked diode laser locked to a stabilized, single frequency, unmodulated diode laser. The master oscillator is a grating-tuned, external cavity diode laser which is stabilized on a Doppler free alkali metal resonance transition frequency via Zeeman locking. The master oscillator frequency is shifted by an acousto-optic modulator, which provides optical isolation of the master oscillator laser while tuning of the acousto-optic modulation frequency can also provide frequency offset tuning. The slave laser is a free running diode which is injection-locked by a small fraction of the frequency shifted master oscillator light. Good long- and short-time frequency stability are observed for both the Zeeman-locked master oscillator and the injection-locked slave laser.     

Selective injection locking of a multi-mode semiconductor laser to a multi-frequency reference beam

Injection locking is a well known and commonly used method for coherent light amplification. Usually injection locking is obtained on a single-mode laser injected by a single-frequency seeding beam. In this work we show that selective injection locking of a single-frequency may also be achieved on a multi-mode semiconductor laser injected by a multi-frequency seeding beam, if the slave laser provides sufficient frequency filtering. This selective injection locking condition depends critically on the frequency detuning between the free-running slave emission frequency and each injected frequency component. Stable selective injection locking to a set of three seeding components separated by 1.2 GHz is obtained. This system provides an amplification up to 37 dB of each component. This result suggests that, using distinct slave lasers for each frequency line, a set of mutually coherent high-power radiation modes can be tuned in the GHz frequency domain.     

掺Er光纤飞秒激光器中电光晶体对激光器参数的影响

由于受增益介质上能级寿命的影响,掺Er光纤光梳的梳齿线宽一般在百kHz量级.为了实现光梳梳齿线宽的压窄,一种有效的方法是在激光器中增加快速响应的电光晶体,使光纤光梳的伺服锁定带宽提高到百kHz以上,为光纤光梳的快速伺服锁定提供反馈机构.这其中,高品质的飞秒激光器是核心.基于此,本文主要研究了掺Er光纤飞秒激光器中电光晶体对激光器参数的影响.通过计算电光晶体的折射率、色散、相位延迟等参数,分析了电光晶体对激光器参数的影响,并在实验上获得了电光晶体电压对激光器重复频率和载波包络偏移频率的影响,进而通过电光晶体实现了对光纤光梳重复频率和载波包络偏移频率的锁定.通过锁定光纤飞秒激光器与窄线宽激光器的拍频信号,验证了电光晶体的引入使激光器的伺服锁定带宽提高到了236 kHz,为窄线宽飞秒光学频率梳的建立提供了技术基础.     

Frequency comb-referenced narrow line width diode laser system for coherent molecular spectroscopy

We analyze in detail the frequency noise properties of a grating enhanced external cavity diode laser (GEECDL). This system merges two diode laser concepts, the grating stabilized diode laser and the diode laser with resonant optical feedback, thus combining a large tuning range with an excellent short-term frequency stability. We compare the frequency noise spectrum of a GEECDL to that of a grating stabilized diode laser and demonstrate a 10-fold reduction of the frequency noise linear spectral density. The GEECDL is phase locked to a similar laser and to a fs-frequency comb with a servo loop providing an open-loop unity-gain frequency of only 237 kHz, which is a tenth of the bandwidth typically required for grating stabilized diode lasers. We achieve a residual rms phase error as small as 72 mrad (≈ 200 mrad) for stabilization to a similar laser (to the fs-frequency comb). We demonstrate that the novel diode laser can phase-coherently track a stable optical reference with an instability of 1.8×10^-16 at 1 s. This laser system is well suited for applications that require phase locking to a low-power optical reference under noisy conditions. It may also be considered for the implementation of optical clock lasers. PACS 42.55.Px; 42.60.Jf; 42.50.Gy     

Optical amplifier for femtosecond frequency comb measurements near 633 nm

An optical amplifier operating at the 633-nm wavelength region is designed for absolute frequency measurements of iodine-stabilized He-Ne lasers with an optical femtosecond frequency comb generator. The same setup can also be used in other applications that require relatively high (15 mW) laser powers with good spectral characteristics. Radiation of a master laser is amplified by a microlens-coupled diode laser, which is injection locked to the frequency of the master laser. The amplifier can be reliably operated over several hours with very low phase noise. Optical amplification of more than 39 dB is demonstrated. PACS 06.20.Fn; 06.30.Ft; 42.55.Px; 42.62.Eh     

Kilohertz-resolution spectroscopy of cold atoms with an optical frequency comb

We have performed sub-Doppler spectroscopy on the narrow intercombination line of cold calcium atoms using the amplified output of a femtosecond laser frequency comb. Injection locking of a 657-nm diode laser with a femtosecond comb allows for two regimes of amplification, one in which many lines of the comb are amplified, and one where a single line is predominantly amplified. The output of the laser in both regimes was used to perform kilohertz-level spectroscopy. This experiment demonstrates the potential for high-resolution absolute-frequency spectroscopy over the entire spectrum of the frequency comb output using a single high-finesse optical reference cavity.     

Passively mode-locked Raman laser

We report on the observation of a mode-locked laser generated with a crystalline whispering gallery mode resonator pumped with a continuous wave laser. Optical pumping of the resonator generates an optical frequency comb with phase locked components at the Raman offset of the resonator host material. Phase locking of the modes is confirmed via measurement of the radio-frequency beat note produced by the comb on a fast photodiode. Neither the conventional Kerr comb nor hyperparametric oscillation is observed when the comb is present. We present a theoretical explanation of the effect.     

Optical and RF stability transfer in a monolithic coupled-cavity colliding pulse mode-locked quantum dot laser

We report a novel quantum dot based laser design where a stable high-Q master laser is used to injection lock a passively mode-locked monolithic colliding pulse slave laser. Coupling between the crossed orthogonal laser cavities is achieved through a common monolithically integrated saturable absorber, which results in the locking and hence reduction of the timing jitter as well as the long-term frequency drift of the slave laser. A stable 30?GHz optical pulse train is generated with more than 10?dB reduction in the RF noise level at 20?MHz offset and close to 3 times reduction in the 10?dB average optical linewidth of the slave laser.     

Observation of optical bistability in a GaAlAs semiconductor laser under intermodal injection locking

Experimental observation of optical bistability in a semiconductor laser under intermodal injection locking is reported for what is believed to be the first time. It is seen that a change in injection power of several microwatts or master laser frequency detuning of a few hundred megahertz can induce a change of as much as several hundred gigahertz in the lasing frequency of the slave laser. The results are in qualitative agreement with theoretical predictions.     

Frequency comb expansion in a monolithic self‐mode‐locked laser concurrent with stimulated Raman scattering

The discovery of a novel phase‐locked frequency comb generated from a monolithic laser with the concurrent processes of self‐mode locking (SML) and stimulated Raman scattering (SRS) is reported. It is experimentally shown that the width of the Raman gain can be exploited to considerably expand the frequency comb of a monolithic SML crystal laser via the SRS process. At a pump power of 6.5 W, an output power of 140 mW in the Stokes wave with a pulse width as narrow as 2.9 ps at a pulse repetition rate of 6.615 GHz is obtained. The present finding not only provides useful insights into the monolithic intracavity SRS process but also paves the way for generating mode‐locked pulses based on monolithic self‐Raman crystals.     

基于双光注入锁定1550 nm垂直腔表面发射半导体激光器产生可调谐毫米波

基于自旋反转模型, 对双光注入下1550 nm 垂直腔表面发射半导体激光器(1550 nm-VCSEL)的非线性动力学行为进行了理论分析和数值仿真研究. 结果表明: 当一个中心波长位于1550 nm 的副VCSEL(S-VCSEL)同时受到来自两个主VCSELs (M-VCSELs)的光注入时, 在适当的注入条件下, S-VCSEL可处于双光注入锁定态. 此时, S-VCSEL中的两偏振模式均呈现频率为两注入光频率之差的周期性振荡, 输出的光谱仅包含两个主频率部分, 即光谱具有单边带特征. 因此, 基于双光注入下S-VCSEL的周期性振荡可以获得两个相互正交的光毫米波. 通过调节两个M-VCSELs之间的频率差异可使毫米波频率在较大范围内连续可调, 通过调节系统参量可以控制毫米波功率以及调制深度. 关键词： 垂直腔表面发射激光器 双光注入 毫米波 调制深度     

用于提高种子注入Nd：YAG激光器性能的一种光学补偿方法的设计计算

分析了利用干涉法实现腔模锁定的种子激光器的工作原理，在此基础上提出了偏转检测器法补偿由于信号处理可引起的滞后，为种子注入激光器的腔模锁定技术的提供了新的改进方法，可方便而有效地控制从振荡器的输出光质。