醇/水介质对PEG大分子单体与BMA分散共聚反应的影响

通过端基反应法合成了苯乙烯单封端的聚乙二醇(St- PEG)大分子单体,使其与甲基丙烯酸丁酯(BMA)在乙醇 水混合介质中进行分散共聚,得到了聚乙二醇接枝的聚甲基丙烯酸丁酯(PBMA- g -PEG)高分子微球.PBMA- g -PEG共聚物的亲溶剂 疏溶剂平衡将影响微球的形成,反应结束时,体系随BMA浓度和介质中水含量的变化呈现出4种不同的状态,透明清液、乳液、伴有沉淀或凝胶的乳液和凝胶.用透射电子显微镜(TEM)和激光光散射(LLS)对乳液体系的粒径及其形态进行了表征,表明所得接枝高分子微球形态规整具有较好的单分散性.通过控制介质中水的含量和BMA的浓度可得粒径在4 0～5 0 0nm范围的PBMA -g -PEG微球.     

PAm-g-PMAA亲水性聚合物微球的合成

利用链转移自由基聚合和端基置换反应法 ,合成了苯乙烯基单封端的聚甲基丙烯酸叔丁酯 (PBMA)大分子单体 .在N ,N′ 亚甲基二丙烯酰胺 (Bis A)存在的条件下 ,使PBMA大分子单体与亲水性单体丙烯酰胺(Am)在乙醇 水的混合介质中进行分散共聚反应 ,得到了表面为PBMA接枝的聚丙烯酰胺 (PAm g PBMA)聚合物微球 .将所得PAm g PBMA微球在酸性条件下水解 ,得到了整体亲水的聚甲基丙烯酸接枝的聚丙烯酰胺(PAm g PMAA)聚合物微球 .用激光光散射、透射电子显微镜和X射线光电子能谱仪等对聚合物微球的直径、形态及表面组成进行了表征 .研究结果表明 ,在共聚反应中PBMA大分子单体的分子量与浓度、Bis A浓度和介质的组成对微球的形成与颗粒直径的大小有明显影响 ;所形成的聚合物颗粒是以PBMA为壳、以交联PAm为核的核壳结构微球 .     

热敏性高分子接枝聚苯乙烯微球的制备

通过使聚N－乙烯基异丁酰胺（PNVIBA）大分子单体与苯乙烯在乙醇／水的混合溶剂中进行自由基分散共聚，得到热敏性PNVIBA接枝聚苯乙烯（PNVIBA－g-PSt)高分子微球。用TEM对微球的形态进行了观察，同时考察了起始PNVIBA大分子单体浓度、苯乙烯浓度、引发剂浓度、聚合温度和混合溶剂中水对微球直径的影响。发现在较宽的聚合反应条件下，得到的接枝高分子颗粒均保持球形并具有单分散性，微球的数均直径（D）与反应条件的关系遵循：D＝K[PNVIBA]^-0.39[St]^0.80[I]^-0.14;微球直径随聚合温度的升高和混合溶剂中水含量增加而降低；颗粒形态可以通过改变聚合反应条件或添加第二小分子单体加以控制。     

复合微球的制备、性能及应用

本文综述了复合微球的制备、性能及其应用，并对其发展趋势作了展望．     

无规-类接枝共聚物自组装制备交联纳米微球

无规-类接枝共聚物(SFG)由大分子单体-己内酯改性丙烯酸酯(FA)、亲油性单体苯乙烯和甲基丙烯酸缩水甘油酯(GMA)共聚所得，SFG与聚苯乙烯在甲醇溶液中进行自组装，形成核壳结构纳米胶束，进一步对PGMA壳进行化学交联。最终得到具有核壳结构的纳米微球。动态激光光散射和透射电子显微镜表征结果显示SFG自组装形成了窄分布的纳米微球，微球粒径在100～200nm之间。     

聚乙二醇接枝聚乳酸的自组装纳米微球的制备及性能

对制备的新型聚乙二醇(PEG)接枝聚乳酸(PLA)在水中的自组装性能进行研究, 探讨其作为纳米药物载体的可行性和稳定性. 目测法得到其溶解度为(2.16～4.32)×10^－2 mg•mL^－1; 荧光法得到聚合物的临界胶束浓度为1.12×10^－3 mg•mL^－1; 透射电子显微镜观察显示该聚合物在水中的自组装聚集体为纳米级球形; 动态激光光散射测试微球的粒径和Zeta电位发现, 在微球的制备过程中, 聚合物的亲/疏水性比例、水相介质及水溶液的pH值对它影响显著; 而制备后, 稀释和冷冻对它无显著影响, 改变微球的环境pH值至酸性, 出现聚集, 至碱性无影响. 研究结果显示, 该聚合物在水和磷酸钠盐缓冲液中可形成稳定的纳米微球, 通过微球的制备条件和存在环境可控制其粒径和Zeta电位, 因此根据应用需要, 通过控制其粒径和Zeta电位, 可能提高微球的在体血液循环时间并实现靶向缓释.     

单分散亚微米级磁性微球的合成

以磁性氧化铁胶体粒子为种子粒子，采用吸附－溶胀法，进行苯乙烯－丙烯酸－二乙烯基苯的乳液聚合，制备亚微米级磁性高分了微球。研究了分散介质、丙烯酸、种子粒子、苯乙烯和ＰＨ调节剂等因素对聚合行为和磁性微球的影响，成功地合成了平均粒径为０．１３和０．２７μｍ、单分散性很好的磁性微球。     

聚甲基丙烯酸甲酯-氯化银复合纳米微球的制备及其摩擦学性能

采用原位种子乳液聚合法合成了聚甲基丙烯酸甲酯 氯化银(PMMA AgCl)核壳结构复合纳米微球,通过透射电镜(TEM),红外光谱(IR),热分析(TG DTA)和X射线粉末衍射(XRD)等测试手段对其结构及性能进行了表征.在四球试验机上对其摩擦学行为进行了考察,研究结果表明,PMMA AgCl核壳结构复合纳米微球用作润滑油添加剂具有良好的抗磨性能,能显著提高基础油的失效负荷.     

磁性纳米包覆微球的制备和磁性表征

以胶体球形粒子为基体发展起来的纳米包覆(nano鄄coating)技术近来引起人们的极大兴趣,这种纳米包覆技术得到的产物常常被称为核壳粒子(core鄄shellparticles)。这种包覆一般是将纳米颗粒直接吸附在核微球上,或者包覆材料控制沉淀在核微球上[1,2]。这些复合微球常常展现出独特的光、电、力学、化学、催化等性质,因而具有广泛的研究和应用前景[3~7]。近十几年来,用做磁感应成像的超顺磁材料得到了深入的研究[4]。一方面,磁性颗粒的尺寸、电荷和表面成分对其应用有很大影响[8,9],另一方面,材料的磁学性质又主要取决于磁颗粒的大小[10]。Xu和Lindlar制备了含超顺磁颗粒的聚合物胶体颗粒,被用于构建超顺磁性的光子晶体[11,12]。在聚合物微粒上包覆氧化铁颗粒通常采用表面沉淀或表面改性官能团诱导反应包覆的方法。但这些方法不能很好控制复合微粒的均一性和表面平整性;Caruso的层鄄层包覆法(Layer鄄byLayer)虽然实现了磁性颗粒包覆[13],然而这种方法非常繁琐而不利于广泛应用。本文报道了一种新的合成磁性包覆颗粒的方法,即以聚合物微球为基核,通过非均相种子生长法包覆磁性纳米颗粒,并研究了...     

以碳微球为核的金纳米壳球体的制备

通过水热合成法制备了单分散碳微球, 并以此单分散碳微球为核, 利用其表面修饰的银纳米粒子作为种子, 进一步还原制备了以碳微球为核、以金为壳的金纳米壳(Nanoshell)球体. 通过透射电子显微镜和紫外可见吸收光谱对其形态以及光谱性质进行了表征. 研究结果表明, 采用该种方法制备出来的碳微球具有良好的单分散性, 表面修饰简便快捷, 利用碳微球为核制备的金纳米壳球体尺寸可控, 在近红外范围内有强吸收. 实验结果证明该方法是制备金纳米壳球体的一种有效新方法.     

Synthesis and Application of Tailored Graft Copolymers from Polystyrene Macromonomer

Comb graft copolymers prepared by macromonomer technique has become applicable for permanent modification of polymer surfaces. In this paper the association and adsorption behavior in solution of the well designed graft copolymer prepared from polystyrene macromonomer and various hydrophilic comonomer was studied and the mechanism of surface accumulation of hydrophilic segment was clarified by surface analysis of polystyrene containing the graft copolymers. Wetting of modified polymer surfaces and the permeability of gases through the film was also discussed.     

Synthesis and Characterization of Novel Ethene‐graft‐Ethene/Propene Copolymers

The synthesis of ethene/propene macromers with a high amount of sterically unhindered vinyl groups is described. These macromers are incorporated as long‐chain branches into polyethylene (PE). The remaining low molecular fractions were removed by Soxhlet extraction. Up to 60 wt.‐% macromer was included, which leads to comb‐like molecular topographies that distinctly affect the rheological behavior. The thermal activation energy increased significantly and the zero shear‐rate viscosity enhancement factor η ₀ / η was also changed noticeably.

     

水溶性CdSe/CdS核壳纳米粒子制备的影响因素及其对CdSe/CdS光谱特性的影响

以半胱氨酸镉配合物为前体, 在水溶液中合成CdSe纳米粒子, 以CdS对其表面进行修饰, 得到具有核壳结构的CdSe/CdS 纳米粒子. 采用XRD, TEM表征其结构及形貌; 以荧光光谱研究了时间、pH值、壳量、壳前体加入方式、稳定剂用量等因素对CdSe/CdS光谱特性的影响.     

核/壳型CdTe@SiO2荧光纳米复合粒子的制备与表征

利用反相微乳法, 以巯基乙酸修饰的水溶性CdTe量子点为核, 包覆SiO₂, 制备得到核壳型CdTe@SiO₂荧光纳米复合粒子. 用紫外-可见(UV-vis)分光光度计, 荧光(PL)分光光度计, 红外(FT-IR)光谱仪, 透射电子显微镜(TEM)等分析测试手段, 对得到的荧光纳米复合粒子的性能进行表征, 结果表明: 得到的CdTe@SiO₂纳米复合粒子是核壳型结构, 由SiO₂壳层包覆多个量子点, 其大小均匀, 水溶性好, 有效地提高了量子点的稳定性, 大大增强了其抗光漂白性能, 为该材料的进一步生物应用打下了良好的基础.     

In situ Synthesis of Oil Based Polymer Composites Containing Silver Nanoparticles

Using electron transfer reaction and free radical polymerization processes a series of triglyceride oil based polymer‐silver nanocomposites were successfully prepared. The whole process was divided into two simultaneous stages; (i) copolymerization of macromonomers obtained from partial glycerides with styrene and (ii) the reduction of silver nitrate to metallic silver nano particles with radicals stemming from the thermolysis of 2,2′‐azoisobutyronitrile (AIBN). Nanocomposites were characterized by TEM and TGA. The obtained polymer nanocomposite was also examined in view of antibacterial effect against Gram‐positive, Gram‐negative, and Spore forming bacteria. It was demonstrated that nanocomposite samples exhibited an antibacterial effect against these bacteria. Film properties of the samples as potential coating material were also studied. Nanocomposite samples showed better film properties than that of the polymer without silver nanoparticles.     

电活性大单体的合成

利用氧化偶联反应,由对苯二胺与端胺基被保护的苯胺二聚体,合成了包含苯胺五聚体的电活性大单体,这条合成路线的特点是,保护了苯胺二聚体的胺端基,防止其进一步反应。利用缩聚反应,由已二胺和１,１,２－十二二胺与大单体合成了电活性聚合物。     

侧基含偶氮苯生色团的短梗霉多糖的制备及光致变色性

利用4-(4-硝基苯偶氮)-1-萘酚的丙烯酸酯与短梗霉多糖进行接枝共聚,制备了侧基含偶氮苯生色团的短梗霉多糖聚合物,并用红外光谱、扫描电镜、X射线衍射、热重分析等手段对聚合物进行了表征.用紫外光谱研究了聚合物的光致变色性,结果表明聚合物具有良好的热稳定性和光致变色性.     

Graft copolymers having hydrophobic backbone and hydrophilic branches. X. Preparation and properties of water-dispersible polyanionic microspheres having poly(methacrylic acid) branches on their surfaces

The free radical copolymerization of poly(t-butyl methacrylate) (PBMA) macromonomer with styrene in ethanol give monodispersed microspheres with 0.8-1.6 μm diameter. The resulting microspheres were treated with HCl solution to convert into anionic microspheres having poly(methacrylic acid) chains. ESCA analysis of the microsphere surface suggested that PBMA chains were favorably located on the surface of the microspheres. The particle size of the microspheres decreased with increasing molecular weight and concentration of the macromonomer. Water dispersibilities of the microspheres were evaluated by measuring the relative turbidity of the suspension of microspheres as a function of pH. The results show that they were strongly dependent on pH. © 1995 John Wiley & Sons, Inc.     

Synthesis of graft copolymers having phospholipid polar group by macromonomer method and their properties in water

Water-soluble graft copolymers with phospholipid polar group were synthesized by the macromonomer method and their properties in water were investigated by surface tension and fluorescence spectroscopic measurements. At first, 2-methacryloyloxyethyl phosphorylcholine (MPC) was polymerized in the presence of 3-mercapt propionic acid as a chain transfer agent and carboxyl group-terminated oligo (MPC) was obtained. The oligo (MPC) reacted with glycidyl methacrylate to convert the carboxyl group to a polymerizable methacryloyl group. The MPC macromonomer obtained was copolymerized with hydrophobic n-butyl methacrylate (BMA) and a graft copolymer was obtained. The graft copolymer, poly(MPC-graft-BMA), was water-soluble when the MPC unit mole fraction was above 0.40. The surface tension of the aqueous solution of poly(MPC-graft-BMA) did not depend on the polymer concentration below 0.1 wt %. This tendency was the same as that which appeared in aqueous poly(MPC) solution. The fluorescence intensity of hydrophobic probes observed in an aqueous solution of the poly (MPC-graft-BMA) was also the same level as that observed in the case of poly(MPC). These results clearly indicated that the poly(MPC-graft-BMA) took a domain structure like micelle in water, i.e., the hydrophobic poly(BMA) backbone was in the core part and the hydrophilic poly(MPC) chain formed the shell part of the micelle. © 1994 John Wiley & Sons, Inc.     

Chitooligosaccharide Copolymers: Synthesis and Aqueous Self-assembly

Novel water-soluble amphiphilic graft copolymers (COS-g-PCL-b-MPEG) were synthesized by the coupling reaction between chitooligosaccharide (COS) and MPEG-b-PCL-COOH, which was synthesized via ring-opening polymerization of ε-caprolactone (CL) using MPEG as an initiator and subsequent carboxylation by succinic anhydride. The chemical composition of the graft copolymers was confirmed by ¹H-NMR spectra and FT-IR spectrometry. The thermal properties and crystallinity of the copolymers were observed by DSC and XRD measurements, which showed the existence of separate backbone and graft chain phases in the copolymer. The micellar behavior via self-assembly of the graft copolymers in aqueous solution was studied using pyrene fluorescence dye technique. AFM measurements showed that the micelles had a spherical morphology at the critical micelle concentration (CMC) and ranged in size from 20–45 nm. The amphiphilic ternary biodegradable graft copolymer endows the hydrophilic outer shell of micelles with structural and functional diversification, which might be desirable for drug delivery applications.