超声喷雾共沉淀法制备的Lu3Al5O12∶Eu3+纳米粉体发光特性

采用新型超声喷雾共沉淀法技术,以Lu2O3、Eu2O3、Al(NO3)3·9H2O为原料,制备了不同浓度Eu3+离子掺杂的Lu3Al5O12纳米粉体.用X射线粉末衍射表征了获得纳米粉体的相,用扫描电镜观察了纳米粒子的形貌.测定了粉体的激发光谱、7F0-5D2声子边带谱与发射光谱.研究了不同高温烧结温度与Eu3+掺杂浓度...     

Eu3+激活的硼钒酸钇的光致发光

找出了合成Eu3+激活的硼钒酸钇铕发光粉的适宜条件和发光最佳化学组分,它是(Y0.94Eu0.06)(V0.69B0.31)O3.7.对其发光光谱的温度依赖关系的研究指出,发光最佳温度在350℃左右.发光的这种温度依赖关系与基质和Eu3+对能量的吸收,以及基质向Eu3+能量传递效率的提高有关.此外,试验结果还表明,在365nm激发下,少显Gd2O3、Zn2GeO4·GeO2:Mn2+等添加剂的加入提高了样品的发光亮度.     

纳米ZnO和ZnO∶Eu3+的表面效应及发光特性

纳米ZnO,ZnO:Eu3+及其添加覆盖层样品的光谱性质表明,表面有机物覆盖层具有改善发射光谱,增强基质与Eu3+间能量传递的良好效果.通过比较不同温度(60,800℃)处理的ZnO:Eu3+发光强度,发现了小尺度(纳米)颗粒的特殊发光行为 关键词： ZnO 表面覆盖层 Eu掺杂     

阴极电沉积ZnO薄膜的取向控制生长

采用阴极电沉积法,在Zn(NO3)2水溶液中,以304不锈钢为衬底制备了ZnO薄膜,研究了Zn2+浓度和电流密度对ZnO薄膜择优取向的影响规律。XRD结果表明:随着Zn2+浓度和电流密度增大,ZnO薄膜逐渐由(002)面择优取向生长转变为(101)面择优取向生长;当Zn2+浓度为0.005mol.L-1、电流密度为2.0mA.cm-2或Zn2+浓度为0.05mol.L-1、电流密度为0.5mA.cm-2时,可以得到(002)面择优取向生长的ZnO薄膜;当Zn2+浓度为0.05mol.L-1、电流密度为2.0mA.cm-2时,可以得到(101)面择优取向生长的ZnO薄膜。根据二维晶核理论,通过分析不同生长条件下的过饱和度及其对ZnO的(002)型和(101)型二维晶核形核活化能的影响,对这一规律进行了解释。可见,通过改变Zn2+浓度和电流密度能够实现阴极电沉积ZnO薄膜的取向可控生长。     

ZnO对Eu∶LiNbO3晶体的性能及光谱性质影响

应用坩埚下降法技术,以同成份化学摩尔分数[x(Li2O)=48.6%,x(Nb2O5)=51.4%]为原料,生长出了以不同Zn,Eu双掺杂的LiNbO3晶体。测定了晶体下部与上部的X射线衍射图(XRD)、激发光谱、荧光光谱以及声子边带谱。Zn的掺杂量对Eu3+离子在晶体中的分布产生很大的影响。Zn掺杂摩尔分数为3%时,Eu3+离子在进入晶格时受到有效的压制。随着Zn掺杂摩尔分数提高,达到6%时,压制作用减弱。从Zn2+离子在LiNbO3中随浓度变化的分凝情况以及对Eu3+离子的排斥作用解释了Eu3+离子分布的原因。同时测定了Zn掺杂样品的声子边带谱。     

纳米ZnO和ZnO∶Eu3+的表面效应及发光特性

纳米ZnO, ZnO:Eu3+及其添加覆盖层样品的光谱性质表明,表面有机物覆盖层具有改善发射光谱, 增强基质与Eu3+间能量传递的良好效果. 通过比较不同温度(60,800℃)处理的ZnO:Eu3+发光强度, 发现了小尺度(纳米)颗粒的特殊发光行为.     

碱金属改性的纳米氧化锌基荧光材料

研究了Zn （NO3）2·6H2O、CO （NH2）2、R-C6H4-SO3Na、Eu2O3和LiNO3为原料,通过均匀沉淀法制备了Eu3＋、Li＋共掺杂的纳米ZnO材料,并通过改变Li＋的掺杂比例来研究纳米氧化锌基材料的发光性能,用XRD、紫外和荧光等分析手段对样品进行表征.结果表明：制得的纳米粉体粒径在50nm左右,引入Li＋后增强了纳米ZnO∶Eu3＋材料的紫外可见光吸收和红色发光性能,且与Li＋的掺杂浓度有关,当Li＋∶Eu3＋的摩尔比为0.6时,其在601nm处的特征峰最强.     

以Eu_2(CA)_3(phen)_2为掺杂剂的Eu~(3+)/TiO_2纳米粉体的制备及其谱学性能研究

采用溶胶-凝胶法制备了分别以Eu(NO3)3和Eu2(CA)3(phen)2(CA:樟脑酸;phen:1,10-菲咯啉)为前驱体,掺杂量为1%(原子摩尔比)的Eu3+/TiO2纳米粉体,通过差热-热重(TG-DTA)、X射线衍射(XRD)、扫描电镜(SEM)、红外光谱(FTIR)、紫外-可见漫反射吸收光谱(UV-Vis)和荧光光谱等分析手段,对样品的结构和谱学性能进行了对比研究。研究表明,稀土Eu3+以有机配合物Eu2(CA)3(phen)2为前躯体掺杂时,能更有效抑制TiO2纳米粉体的颗粒度增长和晶相转变温度;且UV-Vis吸收峰有一定的红移现象。2种样品中均产生了Eu3+578nm(5D0→7F0),590nm(5D0→7F1)和612nm(5D0→7F2)处的特征发射光谱峰,612nm处最强发射峰为Eu3+特征红色发射峰。当稀土Eu3+含量相同时,以有机配合物Eu2(CA)3(phen)2为前躯体制备的纳米粉体发光强度更大。     

溶胶-凝胶法制备Zn2SiO4:Eu3+红色荧光粉

采用溶胶-凝胶法在Zn2SiO4基质中掺杂Eu3+,合成了红色荧光粉Zn2SiO4:Eu3+.通过样品的X射线衍射光谱、红外光谱、扫描电镜以及光致发光光谱的测试和表征,研究了Zn2SiO4:Eu3+的内部结构和发光特性.扣描电镜结果显示样品为球状荧光粉,颗粒直径为1～3μm.在395 nm激发下,样品在613 nm处发射出很强的红光.结合荧光光谱,分析了样品的退火温度,Eu3+的浓度,电荷补偿剂Li+的浓度对样品发光强度的影响.研究发现,红色荧光粉Zn2SiO4:Eu3+的发光强度随退火温度的升高而增加,发光强度随Eu3+和Li+浓度的增加先增大后减小.     

铕掺杂纳米氧化锌晶体结构和荧光光谱的研究

以醋酸锌、氧化铕、氢氧化钠为主要原材料,利用共沉淀法制备ZnO∶Eu3+纳米晶体.在X射线衍射谱中,只观察到氧化锌的峰,没有观察到氧化铕的特征峰.比较了ZnO和ZnO∶Eu3+拉曼光谱,在ZnO∶Eu3+样品拉曼光谱中观察到新的局部振动模.这些现象表明铕离子已经进入氧化锌晶格中.SEM形貌显示Eu3+离子掺入使ZnO晶...     

氧化锌及纳米氧化锌研究进展

ZnO是一种重要的直接宽带隙半导体,室温下禁带宽度为3.37eV,激子束缚能为60meV,对于开发蓝绿、蓝光、紫外等多种发光器件有巨大潜力.纳米ZnO表现出与体材料明显不同的电学、磁学、光学、化学等性质,是目前纳米材料的研究热点之一.本文介绍了ZnO和纳米ZnO的一些基本性质,综述了近年来纳米ZnO的合成以及应用等方面研究的一些进展.     

Properties of nano-ZnO/poly(vinyl alcohol)/poly(ethylene oxide) composite thin films

A series of poly(vinyl alcohol)/nano-ZnO composites were prepared by dispersing nano-ZnO in aqueous solutions containing mixtures of the biodegradable polymers poly(vinyl alcohol) (PVA) and poly(ethylene oxide) (PEO), and composite thin films were prepared by casting. The introduction of nano-ZnO into PVA/PEO mixed solutions significantly decreased the resistivity of the solutions. Ultraviolet absorption, thermal behaviour and visco-elastic properties of the thin films were determined as a function of nano-ZnO content up to 15 wt%. Optimum film properties were obtained with 1 wt% nano-ZnO, higher proportions of nano-ZnO resulting in agglomeration of ZnO particles and deterioration in film properties. The Forouhi and Bloomer model was used for the modelling of ZnO thin films.     

Surface modification of zinc oxide nanoparticle by PMAA and its dispersion in aqueous system

Commercial zinc oxide nanoparticles were modified by polymethacrylic acid (PMAA) in aqueous system. The hydroxyl groups of nano-ZnO particle surface can interact with carboxyl groups (COO-) of PMAA and form poly(zinc methacrylate) complex on the surface of nano-ZnO. The formation of poly(zinc methacrylate) complex was testified by Fourier-transform infrared spectra (FT-IR). Thermogravimetric analysis (TGA) indicated that PMAA molecules were absorbed or anchored on the surface of nano-ZnO particle, which facilitated to hinder the aggregation of nano-ZnO particles. Through particle size analysis and transmission electron micrograph (TEM) observation, it was found that PMAA enhanced the dispersibility of nano-ZnO particles in water. The dispersion stabilization of modified ZnO nanoparticles in aqueous system was significantly improved due to the introduction of grafted polymer on the surface of nanoparticles. The modification did not alter the crystalline structure of the ZnO nanoparticles according to the X-ray diffraction patterns.     

纳米ZnO生长及性质分析

利用低压金属有机化学气相沉积(LP-MOCVD)技术,在表面含有ZnO颗粒作为催化剂的Si(111)衬底上制备了ZnO纳米柱阵列。采用X射线衍射(XRD)、喇曼光谱(Raman)、扫描电子显微镜(SEM)、光致发光(PL)谱分析了样品的晶体结构质量、表面性质和光学性质。结果表明,生长出来的纳米ZnO具有较好的c轴择优取向性。发现氧分压对ZnO纳米柱的生长有重要影响:当氧分压较低时,生长基于VLS机制;当氧分压较高时,生长基于VS机制;通过对N2O流量的控制可实现对ZnO纳米材料的可控生长。     

Nanostructured ZnO synthesis and its application for effective disinfection of <Emphasis Type="Italic">Escherichia coli</Emphasis> micro organism in water

Nanostructured ZnO photo catalyst was synthesized by precipitation method and was applied in conjunction with 355 nm pulsed laser irradiation for effective disinfection of the water contaminated with Escherichia coli micro organism. The morphological studies using X-Ray Diffractometer (XRD) and Transmission Electron Microscope (TEM) were carried out on the synthesized nano-ZnO, and these studies indicated that the catalyst has the crystallographic structure of hexagonal wurtzite and has the grain size of around 20–40 nm. The bacteria decay rate constants were estimated for nine different concentrations of nano-ZnO in infected water. The parametric optimization was carried out, and we could reach the decay rate constant as high as 0.24 min_,⁻¹ which is higher than micro-structured ZnO and the familiar TiO₂ photo catalysts under similar experimental condition.     

真空冷冻干燥结合微乳液法制备纳米ZnO

真空冷冻干燥技术结合反相微乳液法制备了纳米ZnO粉体。利用XRD、TEM及表面积分析仪对制备过程、粉体的结构、形貌、比表面积、孔容进行了表征。探讨了煅烧温度、干燥方式及真空冷冻干燥的主要参数对纳米ZnO的影响。结果表明:该方法较常规方法制备的纳米ZnO粒径小(平均19nm)、分散性好、比表面积大(567.9m2.g-1),对亚甲基蓝溶液的降解(降解率98.6%)具有较高的光催化活性。     

Toxicity of zinc oxide nanoparticles to zebrafish embryo: a physicochemical study of toxicity mechanism

The biological impact of engineered nanomaterials released into the aquatic environment is a major concern. In this work, the properties of ZnO nanoparticles (nano-ZnO, 30 nm) were characterized in a water suspension (E3 medium), and a zebrafish 96-h post fertilization (hpf) embryo–larval test was performed to assess the toxicity of nano-ZnO suspension. Nano-ZnO was found to readily form aggregates with different sizes; small aggregates (142.4–517.7 nm) were still suspended in E3 medium, but large aggregates (>1 μm) quickly deposited on the bottom of 24-well plates; nano-ZnO was partially dissolved to Zn species (Zn_(dis)) in E3 medium. In the nano-ZnO suspension, small aggregates, Zn_(dis), and large aggregates might jointly exert influence on the development of zebrafish embryos. The embryo toxicity test revealed that nano-ZnO killed zebrafish embryos (50 and 100 mg/L), retarded the embryo hatching (1–25 mg/L), reduced the body length of larvae, and caused tail malformation after the 96 hpf exposure. Zn_(dis) only partially contributed to the toxicity of nano-ZnO. This research highlights the need to further investigate the ecotoxicity of nano-ZnO in the water environment.     

Structural properties of the donor indium in nanocrystalline ZnO

The structural properties of the nanocrystalline semiconductor ZnO (nano-ZnO) doped with the donor Indium were investigated by perturbed γγ angular correlation spectroscopy (PAC) and extended X-ray absorption fine structure measurements (EXAFS). Up to an average concentration of one In atom per nanocrystallite, PAC measurements show that about 12% of the ¹¹¹In atoms are incorporated on substitutional Zn sites. At higher In concentrations, new In defect complexes are visible in the PAC spectra, which dominate the spectra if the average In concentration exceeds one In atoms per nanocrystallite. In addition, the local environment of Zn and In atoms in In doped nano-ZnO was investigated by EXAFS. The measurements at the K edge of Zn show that the crystal structure of nano-ZnO corresponds to bulk ZnO. In heavily In doped nano-ZnO the EXAFS experiments at the K edge of In exhibit an expansion of the first O shell about the In site. Since about four O atoms are detected in this first shell a substitutional incorporation of the In atoms in the ZnO lattice is suggested. The second shell to be occupied by Zn atoms as well as higher shells are almost invisible, which might have the same microscopic origin as the occurrence of defect complexes observed by PAC.     

具有四角锥状纳米ZnO的制备及强蓝光发射特性

采用热蒸发锌(Zn)粉的方法在不同的氩气流量下制备了大量的四角锥状ZnO纳米材料。用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和光致发光(PL)谱对样品进行了形貌和发光特性分析。结果表明:合成的ZnO纳米材料受氩气流量影响较大,随着流量的增大,形貌由杂乱无章的结构(线状、块状、树枝状等)变成了均匀一致的四角锥结构,其发光特性随着生长过程中氧相对含量的减少,紫外光发射减弱、蓝光发射明显增强,说明氧空位是引起蓝绿光发射的主要原因。经700℃在空气中氧化处理后蓝绿光消失和氧化后的样品在700℃再经氢气还原处理后蓝绿光又重新出现的实验结果进一步证实了这个结论。本实验结果提供了支持纳米ZnO蓝光发射来自氧空位的实验证据,并初步探讨了四角锥状ZnO纳米结构的生长机理和强蓝光发射机制。     

聚合物纳米复合电解质(PEO)8-ZnO-LiClO4微结构及电导率研究

以聚氧化乙烯(PEO)为基质,成功制备出纳米ZnO掺杂的(PEO)₈-ZnO-LiClO₄离子导电聚合物电解质,并利用多种实验技术,包括扫描电子显微镜、X射线衍射(XRD)、傅里叶变换红外光谱和正电子湮没寿命谱(PALS),系统地研究了纳米ZnO与基质间相互作用及其对聚合物链段运动、纳米尺度自由体积、离子输运和复合电解质电导率的影响.实验结果发现,纳米ZnO的掺杂使聚合物电解质的离子电导率得到了大幅度提高,当ZnO与PEO质量比为6%时达到最大,(PEO)₈-ZnO-LiClO₄的电导率为1.82×10^-4 S ·cm^-1,比(PEO)₈-LiClO₄的电导率(6.58×10^-5 S ·cm^-1)提高了大约一个数量级.XRD结果显示,纳米ZnO的加入降低了PEO的结晶性,增加了锂离子传输的非晶相,从而提高了电导率.离散PALS测量结果表明,随着纳米ZnO的加入,复合电解质的自由体积、浓度和相对自由体积分数f_r均增加.连续PALS分析揭示了自由体积的分布由一个峰劈裂成两个峰,表明纳米ZnO的掺杂对聚合物的微结构有很大影响.基于实验测量的f_r和离子电导率,研究了离子导电机理.研究发现, f_r与电导率之间存在一个直接关系,即f_r越大,越有利于锂离子的传输,导致电导率越大.这个结果支持聚合物电解质导电的自由体积理论. 关键词： 正电子湮没寿命谱 聚合物纳米复合电解质 离子电导率 自由体积