离子液体凝胶聚合物电解质的三元组分相互作用研究

采用Raman光谱、傅里叶转换红外光谱和X-射线衍射光谱研究N-甲基-N-丙基哌啶双三氟甲磺酸亚胺离子液体（PP13TFSI）和双三氟甲磺酸亚胺锂盐（LiTFSI）对PVDF-HFP聚合物聚合方式的影响,结果表明,PP13TFSI、LiTFSI和PVDF-HFP是共混存在的,同时加入PP13TFSI和LiTFSI会使聚合物的聚合方式由晶体结构转变为无定形结构. 通过对电解质及其各组分的线性扫描伏安曲线和热重曲线分析可知,溶剂N-甲基吡咯烷酮（NMP）容易残留在凝胶聚合物电解质（ILGPE）中,这会降低ILGPE的电化学稳定性和热稳定性. 作者对固态LiFePO₄|ILGPE|Li电池的倍率性能进行了研究,实验结果表明其具有较好的倍率性能,当电池倍率由C/10增大至2C,然后再回到C/10时,其容量可以恢复到原来的90.9%左右. 该研究结果对理解PP13TFSI和LiTFSI在ILGPE中的作用机理具有重要的意义.     

Li+ cation environment, transport, and mechanical properties of the LiTFSI doped N-methyl-N-alkylpyrrolidinium+TFSI- ionic liquids

Molecular dynamics (MD) simulations have been performed on N-methyl-N-propylpyrrolidinium bis(trifluoromethanesulfonyl)imide (mppy(+)TFSI(-)) and N,N-dimethyl- pyrrolidinium bis(trifluoromethanesulfonyl)imide (mmpy(+)TFSI(+)) ionic liquids (ILs) doped with 0.25 mol fraction LiTFSI salt at 303-500 K. The liquid density, ion self-diffusion coefficients, and conductivity predicted by MD simulations were found to be in good agreement with experimental data, where available. MD simulations reveal that the Li(+) environment is similar in mppy(+)TFSI(-) and mmpy(+)TFSI(+) ILs doped with LiTFSI. The Li(+) cations were found to be coordinated on average by slightly less than four oxygen atoms with each oxygen atom being contributed by a different TFSI(-) anion. Significant lithium aggregation by sharing up to three TFSI(-) anions bridging two lithiums was observed, particularly at lower temperatures where the lithium aggregates were found to be stable for tens of nanoseconds. Polarization of TFSI(-) anions is largely responsible for the formation of such lithium aggregates. Li(+) transport was found to occur primarily by exchange of TFSI(-) anions in the first coordination shell with a smaller (approximately 30%) contribution also due to Li(+) cations diffusing together with their first coordination shell. In both ILs, ion self-diffusion coefficients followed the order Li(+) < TFSI(-) < mmpy(+) or mppy(+) with all ion diffusion in mmpy(+)TFSI(-) being systematically slower than that in mppy(+)TFSI(-). Conductivity due to the Li(+) cation in LiTFSI doped mppy(+)TFSI(-) IL was found to be greater than that for a model poly(ethylene oxide)(PEO)/LiTFSI polymer electrolyte but significantly lower than that for an ethylene carbonate/LiTFSI liquid electrolyte. Finally, the time-dependent shear modulus for the LiTFSI doped ILs was found to be similar to that for a model poly(ethylene oxide)(PEO)/LiTFSI polymer electrolyte on the subnanosecond time scale.     

A novel ternary polymer electrolyte for LMP batteries based on thermal cross-linked poly(urethane acrylate) in presence of a lithium salt and an ionic liquid

A new ternary polymer electrolyte based on thermally cross-linked poly(urethane acrylate) (PUA), lithium bis(trifluoromethansulfonyl)imide (LiTFSI) and the ionic liquid N-butyl-N-methylpyrrolidinium TFSI (PYR₁₄TFSI) was developed and tested for application in LMP batteries. The polymer electrolyte was a transparent yellow self-standing material with quite good mechanical properties, i.e., comparable to that of a flexible rubber. The room temperature ionic conductivity of the dry polymer electrolyte was found to be as high as 0.1 mS cm⁻¹ for the compound containing 40 wt% of ionic liquid (PYR₁₄TFSI) and a O/Li ratio of 15/1 (Li⁺ from LiTFSI). The thermal analysis of the new cross-linked electrolyte showed that it was homogeneous, amorphous and stable over a wide temperature range extending from −40 °C to 100 °C. The homogeneity of the polymer electrolyte was also confirmed by SEM analysis.     

Synthesis and electrochemical characterization of aPEO-based polymer electrolytes

In this paper, the preparation and purification of an amorphous polymer network, poly[oxymethylene-oligo(oxyethylene)], designated as aPEO, are described. The flexible CH₂CH₂O segments in this host polymer combine appropriate mechanical properties, over a critical temperature range from −20 to 60 °C, with labile salt-host interactions. The intensity of these interactions is sufficient to permit solubilisation of the guest salt in the host polymer while permitting adequate mobility of ionic guest species. We also report the preparation and characterisation of a novel polymer electrolyte based on this host polymer with lithium tetrafluoroborate, LiBF₄, as guest salt. Electrolyte samples are thermally stable up to approximately 250 °C and completely amorphous above room temperature. The electrolyte composition determines the glass transition temperature of electrolytes and was found to vary between −50.8 and −62.4 °C. The electrolyte composition that supports the maximum room temperature conductivity of this electrolyte system is n = 5 (2.10 × 10⁻⁵ S cm⁻¹ at 25 °C). The electrochemical stability domain of the sample with n = 5 spans about 5 V measured against a Li/Li⁺ reference. This new electrolyte system represents a promising alternative to LiCF₃SO₃ and LiClO₄-doped PEO analogues.     

二次锂电池用离子液体电解质研究

合成了哌啶类离子液体N-甲基-N-丙(丁)基哌啶三氟甲基磺酰亚胺[PP13(4)-TFSI], 并与现在常用的两种离子液体1-丁基-3-甲基-咪唑六氟磷酸(BMIPF₆)及1-丁基-3-甲基-咪唑四氟硼酸(BMIBF₄)进行了各种电化学性能的对比. PP13(4)-TFSI的电化学稳定窗口可以达到5.8 V, 明显大于BMIBF₄ (4.7 V) 以及BMIPF₆ (4.6 V). 而且PP13(4)-TFSI负极极限电位(－0.3 V vs. Li/Li^＋)明显低于BMIPF₆ (0.5 V) 和BMIBF₄ (0.7 V), 有望被使用在以锂金属作为负极的二次锂电池中. 以LiTFSI /PP14-TFSI为电解质溶液测试了Li/LiCoO₂纽扣电池的电化学性能, 在0.05 mA•cm^－2的恒定电流充放电条件下, 电池的比容量可以达到150 mAh•g^－1, 初始循环以后库仑效率接近100%. 交流阻抗测试表明, 电池的阻抗特性稳定, 不存在明显的界面钝化现象.     

Effect of ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide on the properties of poly(glycidyl methacrylate) based solid polymer electrolytes

A free standing polymer electrolytes films, containing poly(glycidyl methacrylate) (PGMA) as the polymer host, lithium perchlorate (LiClO₄), and ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl) imide [Bmim][TFSI] as a plasticizer was successfully prepared via the solution casting method. The XRD analysis revealed the amorphous nature of the electrolyte. ATR-FTIR and thermal studies confirmed the interaction and complexation between the polymer host and the ionic liquid. The maximum ionic conductivity of the solid polymer electrolyte was found at 2.56 × 10^–5 S cm^–1 by the addition of 60 wt % [Bmim][TFSI] at room temperature and increased up to 3.19 × 10^–4 S cm^–1 at 373 K, as well as exhibited a transition of temperature dependence of conductivity: Arrhenius-like behavior at low and high temperatures.     

Novel functionalized ionic liquid with a sulfur atom in the aliphatic side chain of the pyrrolidinium cation

A novel ionic liquid, never reported in literature until now, was properly designed, synthesized and preliminary investigated. This material was prepared combining the N-methylpyrrolidinium cation (PYR_1(2S1))⁺, exhibiting a sulfur atom in the alkyl side chain, with the bis(trifluoromethanesulfonyl)imide anion, (TFSI)⁻, to be addressed as safer electrolyte component for sulfur-based battery systems. The presence of sulfur within the cation side chain was found to prevent the crystallization of the ionic liquid even in the presence of lithium salt. Cyclic voltammetries have clearly indicated that Li⁺ cation exhibits good mobility and is reversibly plated/stripped in PYR_1(2S1)TFSI–LiTFSI electrolytes with high efficiency.     

Highly concentrated polycarbonate‐based solid polymer electrolytes having extraordinary electrochemical stability

Solid polymer electrolytes (SPEs) are compounds of great interest as safe and flexible alternative ionics materials, particularly suitable for energy storage devices. We study an unusual dependence on the salt concentration of the ionic conductivity in an SPE system based on poly(ethylene carbonate) (PEC). Dielectric relaxation spectroscopy reveals that the ionic conductivity of PEC/lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) electrolyte continues to increase with increasing salt concentration because the segmental motion of the polymer chains is enhanced by the plasticizing effect of the imide anion. Fourier transfer‐infrared (FTIR) spectroscopy suggests that this unusual phenomenon arises because of a relatively loose coordination structure having moderately aggregated ions, in contrast to polyether‐based systems. Comparative FTIR study against PEC/lithium perchlorate (LiClO₄) electrolytes suggests that weak ionic interaction between Li and TFSI ions is also important. Highly concentrated electrolytes with both reasonable conductivity and high lithium transference number (t₊) can be obtained in the PEC/LiTFSI system as a result of the unusual salt concentration dependence of the conductivity and the ionic solvation structure. The resulting concentrated PEC/LiTFSI electrolytes have extraordinary oxidation stability and prevent any Al corrosion reaction in a cyclic voltammetry. These are inherent effects of the highly concentrated salt. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2442–2447     

Enhanced electrochemical properties of polyethylene oxide-based composite solid polymer electrolytes with porous inorganic–organic hybrid polyphosphazene nanotubes as fillers

Solid composite polymer electrolytes consisting of polyethylene oxide (PEO), LiClO₄, and porous inorganic–organic hybrid poly (cyclotriphosphazene-co-4, 4′-sulfonyldiphenol) (PZS) nanotubes were prepared using the solvent casting method. Differential scanning calorimetry and scanning electron microscopy were used to determine the characteristics of the composite polymer electrolytes. The ionic conductivity, lithium ion transference number, and electrochemical stability window can be enhanced after the addition of PZS nanotubes. The electrochemical impedance showed that the conductivity was improved significantly. Maximum ionic conductivity values of 1.5 × 10⁻⁵ S cm⁻¹ at ambient temperature and 7.8 × 10⁻⁴ S cm⁻¹ at 80 °C were obtained with 10 wt.% content of PZS nanotubes, and the lithium ion transference number was 0.35. The good electrochemical properties of the solid-state composite polymer electrolytes suggested that the porous inorganic–organic hybrid polyphosphazene nanotubes had a promising use as fillers in SPEs and the PEO₁₀–LiClO₄–PZS nanotube solid composite polymer electrolyte might be used as a candidate material for lithium polymer batteries.     

Properties of LiNiO2 cathode and graphite anode in N-methyl-N-propylpyrrolidinium bis(trifluoromethanesulfonyl)imide

Electrochemical properties of LiNiO₂|Li and LiNiO₂|graphite cells were analysed in ionic liquid electrolyte [Li⁺][MePrPyrr⁺][NTf₂^-] (based on N-methyl-N-propylpyrrolidinium bis(trifluoromethanesulphonyl)imide, [MePrPyrr⁺][NTf₂^-]) using impedance spectroscopy and galvanostatic techniques. The ionic liquid is incapable of protective solid electrolyte interface (SEI) formation on metallic lithium or lithiated graphite. However, after addition of VC, the protective coating is formed, facilitating a proper work of the Li-ion cell. Scanning electron microscopy images of pristine electrodes and those taken after electrochemical cycling showed changes which may be interpreted as a result of SEI formation. The charging/discharging capacity of the LiNiO₂ cathode is between 195 and 170 mAh g⁻¹, depending on the rate. The charging/discharging efficiency of the graphite anode drops after 50 cycles from an initial value of ca. 360 mAh g⁻¹ to stabilise at 340 mAh g⁻¹. The replacement of a classical electrolyte in molecular liquids (cyclic carbonates) with an electrolyte based on the MePrPyrrNTf₂ ionic liquid highly increases in the cathode/electrolyte non-flammability.     

Electrochemical Properties of PP13TFSI-LiTFSI-P(VdF-HFP) Ionic Liquid Gel Polymer Electrolytes (cited: 1)

N-Methyl-N-propylpiperidiniumbis(trifluoromethanesulfonyl)imide (PP13TFSI), bis(triflu-oromethanesulfonyl)imide lithium salt (LiTFSI), and poly(vinylidene difluoride-co-hexafluoropropylene) (P(VdF-HFP)) were mixed and made into ionic liquid gel polymerelectrolytes (ILGPEs) by solution casting. The morphology of ILGPEs was observed by scanning electron microscopy. It was found that the ILGPE had a loosened structure with liquid phase uniformly distributed. The ionic conductivity, lithium ion transference num-ber and electrochemical window were measured by electrochemical impedance spectroscopy, chronoamperometric and linear sweep voltammetry. The ionic conductivity and lithium ion transference number of this ILGPE reached 0.79 mS/cm and 0.71 at room temperature, and the electrochemical window was 0 to 5.1 V vs. Li⁺/Li. Battery tests indicated that the ILGPE is stable when being operated in Li/LiFePO₄ batteries. The discharge capacity maintained at about 135, 117, and 100 mAh/g at 30, 75, and 150 mA/g rates, respectively. The capacity retentions were almost 100% after 100 cycles without little capacity fading.     

Composite poly(ethylene carbonate) electrolytes with electrospun silica nanofibers

We prepared a ternary composite polymer electrolyte from poly(ethylene carbonate) (PEC), lithium bis(trifluoromethanesulfonyl) imide (LiTFSI) and non‐calcined silica nanofibers (SNFs) having 3 average diameters (300, 700, and 1000 nm). The SNF composite electrolytes were obtained as homogeneous, self‐standing membranes. The ionic conductivity of PEC/LiTFSI 100 mol% was increased by the addition of SNFs, and the thinner SNFs with average diameter 300 nm were most effective in improving the conductivity. The conductivity was of the order of 10⁻⁴ S/cm at 60°C. The lithium transference number of the SNF₃₀₀ composite was greater than 0.7. Stress‐strain curves of the composites indicated significant increases in Young's modulus and maximum stress for the PEC electrolytes. The 5% weight‐loss temperature of the composites also improved with the addition of SNF.     

A polymer electrolyte containing ionic liquid for possible applications in photoelectrochemical solar cells

Various iodide ion conducting polymer electrolytes have been studied as candidate materials for fabricating photoelectrochemical (PEC) solar cells and energy storage devices. In this study, enhanced ionic conductivity values were obtained for the ionic liquid tetrahexylammonium iodide containing polyethylene oxide (PEO)-based plasticized electrolytes. The analysis of thermal properties revealed the existence of two phases in the electrolyte, and the conductivity measurements showed a marked conductivity enhancement during the melting of the plasticizer-rich phase of the electrolyte. Annealed electrolyte samples showed better conductivity than nonannealed samples, revealing the existence of hysteresis. The optimum conductivity was shown for the electrolytes with PEO:salt = 100:15 mass ratio, and this sample exhibited the minimum glass transition temperature of 72.2 °C. For this optimum PEO to salt ratio, the conductivity of nonannealed electrolyte was 4.4 × 10⁻⁴ S cm⁻¹ and that of the annealed sample was 4.6 × 10⁻⁴ S cm⁻¹ at 30 °C. An all solid PEC solar cell was fabricated using this annealed electrolyte. The short circuit current density (I _SC), the open circuit voltage (V _OC), and the power conversion efficiency of the cell are 0.63 mA cm⁻², 0.76 V, and 0.47% under the irradiation of 600 W m⁻² light.     

A new composite polymer electrolyte based on poly(ethyleneoxide)/ polysiloxane/BMImTFSI/organomontmorillonite

Composite polymer electrolytes based on poly(ethylene oxide)-polysiloxane/l-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide/organomontmorillonite(PEO-PDMS/1L/OMMT) were prepared and characterized.Addition of both an ionic liquid and OMMT to the polymer base of PEO-PDMS resulted in an increase in ionic conductivity.At room temperature,the ionic conductivity of sample PPB100-OMMT4 was 2.19×10~3 S/cm.The composite polymer electrolyte also exhibited high thermal and electrochemical stability and may potentially be applied in lithium batteries.     

Laser Raman and conductivity studies of plasticized polymer electrolyte P(ECH-EO):propylenecarbonate:<Emphasis Type="Italic">γ</Emphasis>-butyrolactone:LiClO<Subscript>4</Subscript>

The plasticized polymer electrolytes composed of poly(epichlorohydrin-ethyleneoxide) (P(ECH-EO)) as host polymer, lithium perchlorate (LiClO₄) as salt, γ-butyrolactone (γ-BL), and propylene carbonate (PC) as plasticizer have been prepared by simple solution casting technique. The effect of mixture of plasticizers γ-BL and PC on conductivity of the polymer electrolyte P(ECH-EO):LiClO₄ has been studied. The band at 457 cm⁻¹ in the Raman spectra of plasticized polymer electrolyte is attributed to both the ring twisting mode of PC and the perchlorate ν ₂(ClO₄⁻) bending. The maximum conductivity value is observed to be 4.5 × 10⁻⁴ S cm⁻¹ at 303 K for 60P(ECH-EO):15PC:10γ-BL:15LiClO₄ electrolyte system. In the present investigation, an attempt has been made to correlate the Raman and conductivity data.     

Enhanced Lithium‐Ion Conductivity of Polymer Electrolytes by Selective Introduction of Hydrogen into the Anion

The anion chemistry of lithium salts plays a pivotal role in dictating the physicochemical and electrochemical performance of solid polymer electrolytes (SPEs), thus affecting the cyclability of all‐solid‐state lithium metal batteries (ASSLMBs). The bis(trifluoromethanesulfonyl)imide anion (TFSI^?) has long been studied as the most promising candidate for SPEs; however, the Li‐ion conductivities of the TFSI‐based SPEs still remain low (Li‐ion transference number: ca. 0.2). In this work, we report new hydrogen‐containing anions, conceived based on theoretical considerations, as an electrolyte salt for SPEs. SPEs comprising hydrogen‐containing anions achieve higher Li‐ion conductivities than TFSI‐based ones, and those anions are electrochemically stable for various kinds of ASSLMBs (Li–LiFePO₄, Li–S, and Li–O₂ batteries). This opens up a new avenue for designing safe and high‐performance ASSLMBs in the future.     

Studies on the thermal behavior of CS:LiTFSI:[Amim] Cl polymer electrolytes exerted by different [Amim] Cl content

The principle motivation of this research work is to develop environmental-friendly polymer electrolytes utilizing corn starch (CS), lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) and 1-allyl-3-methylimidazolium chloride ([Amim] Cl) by solution casting technique. The highest ionic conductivity value was achieved for the composition CS:LiTFSI:[Amim] Cl (14 wt. %:6 wt. %:80 wt. %) which exhibits the ionic conductivity value of 5.68 × 10⁻² S cm⁻¹ at 40 °C with the activation energy of 4.86 kJ mol⁻¹. This sample possess high concentration of amorphous phase coupled with greater presence of conducting cations (lithium, Li⁺ and imidazolium, [Amim]⁺) as depicted by the dielectric loss tangent plot. The conductivity-temperature plots were found to obey Arrhenius rule in which the conductivity mechanism is thermally assisted. The melting temperature of polymer electrolyte decreases with increase in [Amim] Cl content. This is attributed to the good miscibility of [Amim] Cl in CS:LiTFSI matrix inducing structural disorderliness. Reference to the TGA results it is found that the addition of [Amim] Cl diminishes the heat-resistivity whereas enhancement in the thermal stability occurred at the initial addition and declines with further doping of [Amim] Cl.     

Single Lithium‐Ion Conducting Polymer Electrolytes Based on a Super‐Delocalized Polyanion

A novel single lithium‐ion (Li‐ion) conducting polymer electrolyte is presented that is composed of the lithium salt of a polyanion, poly[(4‐styrenesulfonyl)(trifluoromethyl(S‐trifluoromethylsulfonylimino)sulfonyl)imide] (PSsTFSI^?), and high‐molecular‐weight poly(ethylene oxide) (PEO). The neat LiPSsTFSI ionomer displays a low glass‐transition temperature (44.3 °C; that is, strongly plasticizing effect). The complex of LiPSsTFSI/PEO exhibits a high Li‐ion transference number (t_Li⁺=0.91) and is thermally stable up to 300 °C. Meanwhile, it exhibits a Li‐ion conductivity as high as 1.35×10^?4 S cm^?1 at 90 °C, which is comparable to that for the classic ambipolar LiTFSI/PEO SPEs at the same temperature. These outstanding properties of the LiPSsTFSI/PEO blended polymer electrolyte would make it promising as solid polymer electrolytes for Li batteries.     

Application of novel room temperature ionic liquids in flexible supercapacitors

This paper studied application of different types of room temperature ionic liquids (RTILs) into flexible supercapacitors. Typical RTILs including 1-buthyl-3-methyl-imidazolium [BMIM][Cl], trioctylmethylammonium bis(trifluoromethylsulfonyl)imide [OMA][TFSI] and triethylsulfonium bis(trifluoromethylsulfonyl)imide ([SET₃][TFSI]) were studied. [SET₃][TFSI] shows the best result as electrolyte in electrochemical double-layer (EDLC) supercapacitors with very high specific capacitance of 244 F/g at room temperature, overceiling the performance of conventional carbonate electrolyte such as dimethyl carbonate (DMC) with more stable performance and much larger electrochemical window.     

Preparation and properties of ionic‐liquid‐containing poly(ethylene glycol)‐based networked polymer films having lithium salt structures

Ionic‐liquid‐containing polymer films were prepared by swelling poly(ethylene glycol)‐based networked polymers having lithium salt structures with an ionic liquid, 1‐ethyl‐3‐methylimidazolium bis(fluorosulfonyl)imide (EMImFSI), or with an EMImFSI solution of lithium bis(trifluoromethanesulfonyl) imide (LiTFSI). Their fundamental physical properties were investigated. The networked polymer films having lithium salt structures were prepared by curing a mixture of poly(ethylene glycol) diglycidyl ether and lithium 3‐glycidyloxypropanesulfonate or lithium 3‐(glycidyloxypropanesulfonyl)(trifluoromethanesulfonyl)imide with poly(ethylene glycol) bis(3‐aminopropyl) terminated. The obtained ionic‐liquid‐containing films were flexible and self‐standing. They showed high ionic conductivity at room temperature, 1.16–2.09 S/m for samples without LiTFSI and 0.29–0.43 S/m for those with 10 wt % LiTFSI. Their thermal decomposition temperature was above 220 °C, and melting temperature of the ionic liquid incorporated in the film was around ?16 °C. They exhibited high safety due to good nonflammability of the ionic liquid. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011