Aerodynamic Coefficients and Deformation Measurements on Flexible Micro Air Vehicle Wings

This paper documents the elastic deformations and corresponding aerodynamic coefficients of flexible wings used for micro air vehicles (MAVs). These low-aspect ratio wings, developed and fabricated at the University of Florida, incorporate an elastic latex membrane skin covering a thin carbon fiber skeleton. The wings were tested in a unique low-speed wind tunnel facility integrating a visual image correlation (VIC) system with a six-component strain gauge sting balance. Model characteristics are presented, along with the appropriate specimen preparation techniques and wind tunnel instrumentation. The static response characteristics, including full-field displacements and plane strain measurements, for three distinct MAV wing designs are presented. The full-field deformation results show how passive wing flexibility preferably affects aerodynamic performance when compared to a rigid model of similar geometry.     

A simulation-based study on longitudinal gust response of flexible flapping wings

Winged animals such as insects are capable of flying and surviving in an unsteady and unpredictable aerial environment. They generate and control aerodynamic forces by flapping their flexible wings. While the dynamic shape changes of their flapping wings are known to enhance the efficiency of their flight, they can also affect the stability of a flapping wing flyer under unpredictable disturbances by responding to the sudden changes of aerodynamic forces on the wing. In order to test the hypothesis, the gust response of flexible flapping wings is investigated numerically with a specific focus on the passive maintenance of aerodynamic forces by the wing flexibility. The computational model is based on a dynamic flight simulator that can incorporate the realistic morphology, the kinematics, the structural dynamics, the aerodynamics and the fluid–structure interactions of a hovering hawkmoth. The longitudinal gusts are imposed against the tethered model of a hovering hawkmoth with flexible flapping wings. It is found that the aerodynamic forces on the flapping wings are affected by the gust, because of the increase or decrease in relative wingtip velocity or kinematic angle of attack. The passive shape change of flexible wings can, however, reduce the changes in the magnitude and direction of aerodynamic forces by the gusts from various directions, except for the downward gust. Such adaptive response of the flexible structure to stabilise the attitude can be classified into the mechanical feedback, which works passively with minimal delay, and is of great importance to the design of bio-inspired flapping wings for micro-air vehicles.     

柔性扑翼的气动特性研究

以往扑翼的气动力计算研究都很少考虑扑翼的柔性,而在鸟的扑翼动作中,在外加气动力和鸟自身的扑动力作用下,扑翼的柔性变形相当大。本文在原有匀速刚性模型的基础上,提出考虑了扑翼扑动速率变化和形状变化的扑翼分析模型,使之更接近鸟翼柔性扑动真实情况。通过计算分析气动特性发现,控制适当的话,柔性变形能大大改善扑翼的气动性能。本文通过模拟鸟扑翼的柔性运动,计算了时柔性扑翼气动力以及平均升力系数和平均推力系数随着扑动角、倾斜角等参数变化的情况,从而从气动的角度解释了为什么鸟在不同的飞行阶段扑翼规律各不相同,并为柔性扑翼飞行器的设计提供了理论依据。     

Nondimensional frequency scaling of aerodynamically-tensioned membranes

Membrane wings have applications that involve low Reynolds number flyers such as micro air vehicles. The time-averaged and time-dependent deformations of the membrane affect the aerodynamic characteristics of the wing, primarily in the region beyond the maximum aerodynamic efficiency of the wing. This paper investigates an appropriate nondimensional vibration frequency scaling of a spanwise tensioned membrane with free (unattached) leading and trailing edges at low Reynolds numbers relative to nondimensional aeroelastic parameters. Silicone rubber membranes with varying spanwise pre-tension, aerodynamic tension (due to wing angle-of-attack and flow dynamic pressure), modulus of elasticity, span, and thickness are studied. Experimental results are compared to a proposed scaling that simplifies the aerodynamic loading as a uniform pressure distribution acting on the membrane. Data is further compared and discussed relative to previous published results of membrane wings with finite wing spans (three-dimensional flow) and fixed (rigid) leading edges.     

仿生扑翼飞行机器人翅型的研制与实验研究

模仿昆虫和小鸟飞行的扑翼飞行机器人将举升、悬停和推进功能集于一个扑翼系统,与固定翼和旋翼完全不同,因此研究只能从生物仿生开始。生物飞行的极端复杂性使得进行完整和精确的扑翼飞行分析非常复杂,因此本文在仿生学进展基础上,通过一些合适的假设和简化,建立了仿生翅运动学和空气动力学模型,并以此为基础研制了多种翅型。研制了气动力测量实验平台,对各种翅型进行了实验研究。实验结果表明,研制的翅型都能产生一定的升力,其中柔性翅具有较好的运动性能和气动性能,并且拍动频率和拍动幅度对升力有较大影响。     

Aerodynamic and functional consequences of wing compliance

A growing body of evidence indicates that a majority of insects experience some degree of wing deformation during flight. With no musculature distal to the wing base, the instantaneous shape of an insect wing is dictated by the interaction of aerodynamic forces with the inertial and elastic forces that arise from periodic accelerations of the wing. Passive wing deformation is an unavoidable feature of flapping flight for many insects due to the inertial loads that accompany rapid stroke reversals—loads that well exceed the mean aerodynamic force. Although wing compliance has been implicated in a few lift-enhancing mechanisms (e.g., favorable camber), the direct aerodynamic consequences of wing deformation remain generally unresolved. In this paper, we present new experimental data on how wing compliance may affect the overall induced flow in the hawkmoth, Manduca sexta. Real moth wings were subjected to robotic actuation in their dominant plane of rotation at a natural wing beat frequency of 25 Hz. We used digital particle image velocimetry at exceptionally high temporal resolution (2,100 fps) to assess the influence of wing compliance on the mean advective flows, relying on a natural variation in wing stiffness to alter the amount of emergent deformation (freshly extracted wings are flexible and exhibit greater compliance than those that are desiccated). We find that flexible wings yield mean advective flows with substantially greater magnitudes and orientations more beneficial to lift than those of stiff wings. Our results confirm that wing compliance plays a critical role in the production of flight forces. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Experimental investigation of the effect of chordwise flexibility on the aerodynamics of flapping wings in hovering flight

Ornithopters or mechanical birds produce aerodynamic lift and thrust through the flapping motion of their wings. Here, we use an experimental apparatus to investigate the effects of a wing's twisting stiffness on the generated thrust force and the power required at different flapping frequencies. A flapping wing system and an experimental set-up were designed to measure the unsteady aerodynamic and inertial forces, power usage and angular speed of the flapping wing motion. A data acquisition system was set-up to record important data with the appropriate sampling frequency. The aerodynamic performance of the vehicle under hovering (i.e., no wind) conditions was investigated. The lift and thrust that were produced were measured for different flapping frequencies and for various wings with different chordwise flexibilities. The results show the manner in which the elastic deformation and inertial flapping forces affect the dynamical behavior of the wing. It is shown that the generalization of the actuator disk theory is, at most, only valid for rigid wings, and for flexible wings, the power P varies by a power of about 1.0  of the thrust T. This aerodynamic information can also be used as benchmark data for unsteady flow solvers.     

The effects of corrugation and wing planform on the aerodynamic force production of sweeping model insect wings

The effects of corrugation and wing planform (shape and aspect ratio) on the aerodynamic force production of model insect wings in sweeping (rotating after an initial start) motion at Reynolds number 200 and 3500 at angle of attack 40° are investigated, using the method of computational fluid dynamics. A representative wing corrugation is considered. Wing-shape and aspect ratio (AR) of ten representative insect wings are considered; they are the wings of fruit fly, cranefly, dronefly, hoverfly, ladybird, bumblebee, honeybee, lacewing (forewing), hawkmoth and dragonfly (forewing), respectively (AR of these wings varies greatly, from 2.84 to 5.45). The following facts are shown. (1) The corrugated and flat-plate wings produce approximately the same aerodynamic forces. This is because for a sweeping wing at large angle of attack, the length scale of the corrugation is much smaller than the size of the separated flow region or the size of the leading edge vortex (LEV). (2) The variation in wing shape can have considerable effects on the aerodynamic force; but it has only minor effects on the force coefficients when the velocity at r ₂ (the radius of the second moment of wing area) is used as the reference velocity; i.e. the force coefficients are almost unaffected by the variation in wing shape. (3) The effects of AR are remarkably small: when AR increases from 2.8 to 5.5, the force coefficients vary only slightly; flowfield results show that when AR is relatively large, the part of the LEV on the outer part of the wings sheds during the sweeping motion. As AR is increased, on one hand, the force coefficients will be increased due to the reduction of 3-dimensional flow effects; on the other hand, they will be decreased due to the shedding of part of the LEV; these two effects approximately cancel each other, resulting in only minor change of the force coefficients.     

蜻蜓滑翔时柔性褶皱前翅气动特性分析

蜻蜓是自然界优秀的飞行家,滑翔是其常见且有效的飞行模式.蜻蜓优异的飞行能力来源于其翅膀的巧妙结构,褶皱是蜻蜓翅膀上最为显著的结构之一,不仅提高了翅膀的刚度,还改变了其气动特性,而飞行过程中柔性翅膀会产生变形是蜻蜓翅膀的另一特性.为揭示蜻蜓在滑翔时,柔性褶皱前翅的变形,探究褶皱和柔性的共同作用对其气动特性的影响,基于逆向工程,依据前人的测量数据和研究成果,通过三维建模软件建立了蜻蜓三维褶皱前翅的计算流体力学(computational fluiddynamics,CFD)模型和计算结构力学(computational structuralmechanics,CSD)模型,并通过模态分析验证了此模型有足够的精度.基于CFD方法和CFD/CSD双向流固耦合计算方法分别对蜻蜓滑翔飞行时刚性和柔性褶皱前翅的气动特性进行了数值模拟,结果表明,柔性褶皱前翅受气动载荷后,翅脉和翅膜产生形变,柔性前翅上下表面压力差相较于刚性前翅减小了,从而其升力和阻力也减小了,而在大攻角时,变形后的前缘脉诱导出比刚性前翅更强的前缘涡.因此在攻角小于10$^\circ$时刚性前翅的气动特性优于柔性前翅,继续增大攻角,柔性前翅的气动特性则优于刚性前翅.前翅受载后气动响应时间短,翅尖的变形最大,仅仅产生了垂直于翅膀所在平面方向上的变形,而没有发生扭转,翼根处受到应力最大,褶皱上凸部分承受蜻蜓滑翔时前翅的主要载荷.      

On the aerodynamic characteristics of hovering rigid and flexible hawkmoth-like wings

Insect wings are subjected to fluid, inertia and gravitational forces during flapping flight. Owing to their limited rigidity, they bent under the influence of these forces. Numerical study by Hamamoto et al. (Adv Robot 21(1–2):1–21, 2007) showed that a flexible wing is able to generate almost as much lift as a rigid wing during flapping. In this paper, we take a closer look at the relationship between wing flexibility (or stiffness) and aerodynamic force generation in flapping hovering flight. The experimental study was conducted in two stages. The first stage consisted of detailed force measurement and flow visualization of a rigid hawkmoth-like wing undergoing hovering hawkmoth flapping motion and simple harmonic flapping motion, with the aim of establishing a benchmark database for the second stage, which involved hawkmoth-like wing of different flexibility performing the same flapping motions. Hawkmoth motion was conducted at Re = 7,254 and reduced frequency of 0.26, while simple harmonic flapping motion at Re = 7,800 and 11,700, and reduced frequency of 0.25. Results show that aerodynamic force generation on the rigid wing is governed primarily by the combined effect of wing acceleration and leading edge vortex generated on the upper surface of the wing, while the remnants of the wake vortices generated from the previous stroke play only a minor role. Our results from the flexible wing study, while generally supportive of the finding by Hamamoto et al. (Adv Robot 21(1–2):1–21, 2007), also reveal the existence of a critical stiffness constant, below which lift coefficient deteriorates significantly. This finding suggests that although using flexible wing in micro air vehicle application may be beneficial in term of lightweight, too much flexibility can lead to deterioration in flapping performance in terms of aerodynamic force generation. The results further show that wings with stiffness constant above the critical value can deliver mean lift coefficient almost the same as a rigid wing when executing hawkmoth motion, but lower than the rigid wing when performing a simple harmonic motion. In all cases studied (7,800 ≤ Re ≤ 11,700), the Reynolds number does not alter the force generation significantly.     

Experimental study on interaction of aerodynamics with flexible wings of flapping vehicles in hovering and cruise flight

Flapping wings are promising lift and thrust generators, especially for very low Reynolds numbers. To investigate aeroelastic effects of flexible wings (specifically, wing’s twisting stiffness) on hovering and cruising aerodynamic performance, a flapping-wing system and an experimental setup were designed and built. This system measures the unsteady aerodynamic and inertial forces, power usage, and angular speed of the flapping wing motion for different flapping frequencies and for various wings with different chordwise flexibility. Aerodynamic performance of the vehicle for both no wind (hovering) and cruise condition was investigated. Results show how elastic deformations caused by interaction of inertial and aerodynamic forces with the flexible structure may affect specific power consumption. This information was used here to find a more suitable structural design. The best selected design in our tests performs up to 30% better than others (i.e., less energy consumption for the same lift or thrust generation). This measured aerodynamic information could also be used as a benchmarking data for unsteady flow solvers.     

The effects of corrugation and wing planform on the aerodynamic force production of sweeping model insect wings

The effects of corrugation and wing planform (shape and aspect ratio) on the aerodynamic force production of model insect wings in sweeping (rotating after an initial start) motion at Reynolds number 200 and 3500 at angle of attack 40° are investigated, using the method of computational fluid dynamics. A representative wing corrugation is considered. Wing-shape and aspect ratio (AR) of ten representative insect wings are considered; they are the wings of fruit fly, cranefly, dronefly, hoverfly, ladybird, bumblebee, honeybee, lacewing (forewing), hawkmoth and dragonfly (forewing), respectively (AR of these wings varies greatly, from 2.84 to 5.45). The following facts are shown. (1) The corrugated and flat-plate wings produce approximately the same aerodynamic forces. This is because for a sweeping wing at large angle of attack, the length scale of the corrugation is much smaller than the size of the separated flow region or the size of the leading edge vortex (LEV). (2) The variation in wing shape can have considerable effects on the aerodynamic force; but it has only minor effects on the force coefficients when the velocity at r ₂ (the radius of the second moment of wing area) is used as the reference velocity; i.e. the force coefficients are almost unaffected by the variation in wing shape. (3) The effects of AR are remarkably small: when AR increases from 2.8 to 5.5, the force coefficients vary only slightly; flowfield results show that when AR is relatively large, the part of the LEV on the outer part of the wings sheds during the sweeping motion. As AR is increased, on one hand, the force coefficients will be increased due to the reduction of 3-dimensional flow effects; on the other hand, they will be decreased due to the shedding of part of the LEV; these two effects approximately cancel each other, resulting in only minor change of the force coefficients. The project supported by the National Natural Science Foundation of China (10232010 and 10472008) and Ph. D. Student Foundation of Chinese Ministry of Education (20030006022) The English text was polished by Keren Wang.     

Influence of wing flexibility on the aerodynamic performance of a tethered flapping bumblebee

The sophisticated structures of flapping insect wings make it challenging to study the role of wing flexibility in insect flight. In this study, a mass-spring system is used to model wing structural dynamics as a thin, flexible membrane supported by a network of veins. The vein mechanical properties can be estimated based on their diameters and the Young's modulus of cuticle. In order to analyze the effect of wing flexibility, the Young's modulus is varied to make a comparison between two different wing models that we refer to as flexible and highly flexible. The wing models are coupled with a pseudo-spectral code solving the incompressible Navier–Stokes equations, allowing us to investigate the influence of wing deformation on the aerodynamic efficiency of a tethered flapping bumblebee. Compared to the bumblebee model with rigid wings, the one with flexible wings flies more efficiently, characterized by a larger lift-to-power ratio.     

Lift enhancement through flexibility of plunging wings at low Reynolds numbers

In this paper the combined effect of two mechanisms for lift enhancement at low Reynolds numbers are considered, wing oscillations and wing flexibility. The force, deformation and flow fields of rigid and flexible low aspect ratio (AR=3) and high aspect ratio (AR=6) wings oscillating at a fixed post-stall angle of attack of 15° and amplitude of 15% of chord are measured. The force measurements show that flexibility can increase the time-averaged lift coefficient significantly. For low aspect ratio wings the maximum lift coefficient across all Strouhal numbers was C_l=1.38 for the rigid wing as opposed to C_l=2.77 for the flexible wing. Very similar trends were observed for the high aspect ratio wings. This increase is associated with significant deformation of the wing. The root is sinusoidally plunged with small amplitude but this motion is amplified along the span resulting in a larger tip motion but with a phase lag. The amount it is amplified strongly depends on Strouhal number. A Strouhal number of Sr_c=1.5 was selected for detailed flow field measurements due to it being central to the high-lift region of the flexible wings, producing approximately double the lift of the rigid wing. For this Strouhal number the rigid wings exhibit a Leading Edge Vortex (LEV) ring. This is where the clockwise upper-surface LEV pairs with the counter-clockwise lower-surface LEV to form a vortex ring that self-advects upstream and away from the wing's upper surface. Conversely the deformation of the flexible wings inhibits the formation of the LEV ring. Instead a strong upper-surface LEV forms during the downward motion and convects close to the airfoil upper surface thus explaining the significantly higher lift. These measurements demonstrate the significant gains that can be achieved through the combination of unsteady aerodynamics with flexible structures.     

Effects of camber angle on aerodynamic performance of flapping-wing micro air vehicle

This study investigates the unsteady aerodynamic characteristics of the cambered wings of a flapping-wing micro air vehicle (FW-MAV) in hover. A three-dimensional fluid–structure interaction solver is developed for a realistic modeling of large-deforming wing structure and geometry. Cross-validation is conducted against the experimental results obtained also in the present study to establish more accurate analyses of cambered wings. An investigation is carried out on the unsteady vortex structures around the wings caused by the passive twisting motion. A parametric study is then conducted to evaluate the aerodynamic performance with respect to the camber angle at three different flapping frequencies including normal operating conditions. The camber angles producing the largest thrust and highest propulsive efficiency are estimated at each flapping frequency, and their effects on aerodynamic performance are analyzed in terms of the stroke phase. The timing and magnitude of the passive twisting motion, which are dependent on the camber angle at the operating frequency, greatly affects the unsteady vortex structure. Consequently, the camber angle designed at the operating frequency plays a key role in enhancing the aerodynamic performance of FW-MAVs.     

Experimental investigation of a flapping wing model

The main objective of this research study was to investigate the aerodynamic forces of an avian flapping wing model system. The model size and the flow conditions were chosen to approximate the flight of a goose. Direct force measurements, using a three-component balance, and PIV flow field measurements parallel and perpendicular to the oncoming flow, were performed in a wind tunnel at Reynolds numbers between 28,000 and 141,000 (3–15 m/s), throughout a range of reduced frequencies between 0.04 and 0.20. The appropriateness of quasi-steady assumptions used to compare 2D, time-averaged particle image velocimetry (PIV) measurements in the wake with direct force measurements was evaluated. The vertical force coefficient for flapping wings was typically significantly higher than the maximum coefficient of the fixed wing, implying the influence of unsteady effects, such as delayed stall, even at low reduced frequencies. This puts the validity of the quasi-steady assumption into question. The (local) change in circulation over the wing beat cycle and the circulation distribution along the wingspan were obtained from the measurements in the tip and transverse vortex planes. Flow separation could be observed in the distribution of the circulation, and while the circulation derived from the wake measurements failed to agree exactly with the absolute value of the circulation, the change in circulation over the wing beat cycle was in excellent agreement for low and moderate reduced frequencies. The comparison between the PIV measurements in the two perpendicular planes and the direct force balance measurements, show that within certain limitations the wake visualization is a powerful tool to gain insight into force generation and the flow behavior on flapping wings over the wing beat cycle.     

Structural Analysis of a Dragonfly Wing

Dragonfly wings are highly corrugated, which increases the stiffness and strength of the wing significantly, and results in a lightweight structure with good aerodynamic performance. How insect wings carry aerodynamic and inertial loads, and how the resonant frequency of the flapping wings is tuned for carrying these loads, is however not fully understood. To study this we made a three-dimensional scan of a dragonfly (Sympetrum vulgatum) fore- and hindwing with a micro-CT scanner. The scans contain the complete venation pattern including thickness variations throughout both wings. We subsequently approximated the forewing architecture with an efficient three-dimensional beam and shell model. We then determined the wing’s natural vibration modes and the wing deformation resulting from analytical estimates of 8 load cases containing aerodynamic and inertial loads (using the finite element solver Abaqus). Based on our computations we find that the inertial loads are 1.5 to 3 times higher than aerodynamic pressure loads. We further find that wing deformation is smaller during the downstroke than during the upstroke, due to structural asymmetry. The natural vibration mode analysis revealed that the structural natural frequency of a dragonfly wing in vacuum is 154 Hz, which is approximately 4.8 times higher than the natural flapping frequency of dragonflies in hovering flight (32.3 Hz). This insight in the structural properties of dragonfly wings could inspire the design of more effective wings for insect-sized flapping micro air vehicles: The passive shape of aeroelastically tailored wings inspired by dragonflies can in principle be designed more precisely compared to sail like wings —which can make the dragonfly-like wings more aerodynamically effective.     

Numerical simulation of flapping‐wing insect hovering flight at unsteady flow

A computational fluid dynamics (CFD) analysis was conducted to study the unsteady aerodynamics of a virtual flying bumblebee during hovering flight. The integrated geometry of bumblebee was established to define the shape of a three‐dimensional virtual bumblebee model with beating its wings, accurately mimicking the three‐dimensional movements of wings during hovering flight. The kinematics data of wings documented from the measurement to the bumblebee in normal hovering flight aided by the high‐speed video. The Navier–Stokes equations are solved numerically. The solution provides the flow and pressure fields, from which the aerodynamic forces and vorticity wake structure are obtained. Insights into the unsteady aerodynamic force generation process are gained from the force and flow‐structure information. The CFD analysis has established an overall understanding of the viscous and unsteady flow around the virtual flying bumblebee and of the time course of instantaneous force production, which reveals that hovering flight is dominated by the unsteady aerodynamics of both the instantaneous dynamics and also the past history of the wing. A coherent leading‐edge vortex with axial flow and the attached wingtip vortex and trailing edge vortex were detected. The leading edge vortex, wing tip vortex and trailing edge vortex, which caused by the pressure difference between the upper and the lower surface of wings. The axial flow, which include the spanwise flow and chordwise flow, is derived from the spanwise pressure gradient and chordwise pressure gradient, will stabilize the vortex and gives it a characteristic spiral conical shape. Copyright © 2006 John Wiley & Sons, Ltd.     

Effects of unsteady deformation of flapping wing on its aerodynamic forces

Effects of unsteady deformation of a flapping model insect wing on its aerodynamic force production are studied by solving the Navier-Stokes equations on a dynamically deforming grid.Aerodynamic forces on the flapping wing are not much affected by considerable twist,but affected by camber deformation.The effect of combined camber and twist deformation is similar to that of camber deformation.With a deformation of 6% camber and 20°twist(typical values observed for wings of many insects),lift is increased bv 10%～20%and lift-to-drag ratio by around 10%compared with the case of a rigid flat-plate wing.As a result.the deformation can increase the maximum lift coefficient of an insect.and reduce its power requirement for flight.For example,for a hovering bumblebee with dynamically deforming wings(6?mber and 20°twist),aerodynamic power required is reduced by about 16%compared with the case of rigid wings.     

A computational study of the wing–wing and wing–body interactions of a model insect

The aerodynamic interaction between the contralateral wings and between the body and wings of a model insect are studied, by using the method of numerically solving the Navier-Stokes equations over moving overset grids, under typical hovering and forward flight conditions. Both the interaction between the contralateral wings and the interaction between the body and wings are very weak, e.g. at hovering, changes in aerodynamic forces of a wing due to the present of the other wing are less than 3% and changes in aerodynamic forces of the wings due to presence of the body are less than 2%. The reason for this is as following. During each down- or up-stroke, a wing produces a vortex ring, which induces a relatively large jet-like flow inside the ring but very small flow outside the ring. The vortex rings of the left and right wings are on the two sides of the body. Thus one wing is outside vortex ring of the other wing and the body is outside the vortex rings of the left and right wings, resulting in the weak interactions.