Morphology and thermal degradation studies of melt-mixed poly(lactic acid) (PLA)/poly(ε-caprolactone) (PCL) biodegradable polymer blend nanocomposites with TiO2 as filler

The morphology and thermal stability of melt-mixed poly(lactic acid) (PLA)/poly(ε-caprolactone) (PCL) blend nanocomposites with small amounts of TiO₂ nanoparticles were investigated. The nanoparticles were mostly located in the PLA phase, with good dispersion of individual particles, although significant aggregation was also visible. The thermal stability and degradation behaviour of the different samples were studied using thermogravimetric analysis (TGA) and TGA-Fourier-transform infrared (FTIR) spectroscopy. Neat PCL showed better thermal stability than PLA, but the degradation kinetics revealed that PLA had a higher activation energy of degradation than PCL, indicating its degradation rate more strongly depends on temperature, probably because of a more complex degradation mechanism based on chain scission and re-formation. Blending of PLA and PCL reduced the thermal stabilities of both polymers, but the presence of TiO₂ nanoparticles improved their thermal stability. The nanoparticles also influenced the volatilization of the degradation products from the blend, acted as degradation catalyst and/or retarded the escape of volatile degradation products.     

In vitro degradation and release behavior of porous poly(lactic acid) scaffolds containing chitosan microspheres as a carrier for BMP-2-derived synthetic peptide

To develop a novel tissue engineering scaffold with the capability of controlled releasing BMP-2-derived synthetic peptide, porous poly(lactic acid)/chitosan microspheres (PLA/CMs) composites containing different quantities of chitosan microspheres were prepared by a thermally induced phase separation method. FTIR analysis revealed that there were strong hydrogen bond interactions between the PLA and chitosan component. Introduction of less than 30% CMs (on PLA weight basis) did not remarkably affect the morphology and porosity of the PLA/CMs scaffolds. The compressive strength of the composite scaffolds increased from 0.48 to 0.66 MPa, while the compressive modulus increased from 7.29 to 8.23 MPa as the microspheres' contents increased from 0% to 50%. In vitro degradability investigation indicated that the dissolution of chitosan component was preferential than PLA matrix and the inclusion of CMs could neutralize the acidity of PLA degradation products. Compared with the rapid release from CMs, the synthetic peptide was released from PLA/CMs scaffolds in a temporally controlled manner, mainly depending on the degradation of PLA matrix. The promising microspheres based scaffold release system can be used to deliver bioactive factors for a variety of non-loaded bone regeneration and tissue engineering application.     

Dielectric investigations on how Mg salt is dispersed in and released from polylactic acid

Composite biomaterials made of biodegradable polylactic acid （PLA） and bioactive magnesium （Mg） salt are developed for orthopaedic implants or metal implant coatings. The releasing of Mg salt into the biological environment benefits the bone growth, while with the releasing of Mg salt and degradation of PLA there forms a porous scaffold for tissue engineering. The size and morphology of the salt and voids are adjustable with such preparation conditions as salt content, pH of casting solution, and the solidification rate, so that we can control the salt releasing and degradation rate of PLA. Dielectric spectroscopy is used to investigate the dispersive structures of Mg salt and voids in the polymer matrix and to monitor the in situ releasing of Mg salts in the simulated body fluid （SBF）. The current study provides us with an orthopedic biomaterial with controllable multi-phase structures, and a tool to investigate the in vivo behaviors of biomaterials.     

Electrospun poly(l-lactide)-grafted hydroxyapatite/poly(l-lactide) nanocomposite fibers

Composite fibers composed of poly(l-lactide)-grafted hydroxyapatite (PLA-g-HAP) nanoparticles and polylactide (PLA) matrix were prepared by electro-spinning. Environmental scanning electron microscope (ESEM) and transmission electron microscopy (TEM) were employed to investigate the morphology of the composite fibers and the distribution of PLA-g-HAP nanoparticles in the fibers, respectively. At a low content (∼4 wt%) of PLA-g-HAP, the nanoparticles dispersed uniformly in the fibers and the composite fibrous mats exhibited higher strength properties, compared with the pristine PLA fiber mats and the simple hydroxyapatite/PLA blend fiber mats. But when the content of PLA-g-HAP further increased, the nanoparticles began to aggregate, which resulted in the deterioration of the mechanical properties of the composite fiber mats. The degradation behaviors of the composite fiber mats were closely related to the content of PLA-g-HAP. At a low PLA-g-HAP content, degradation may be delayed due to the reduction of autocatalytic degradation of PLA. When PLA-g-HAP content was high, degradation rate increased because of the enhanced wettability of the composite fibers and the escape of the nanoparticles from fiber surfaces during incubation.     

Preparation of poly(lactide-co-glycolide-co-caprolactone) nanoparticles and their degradation behaviour in aqueous solution

The tri-component copolymer poly(lactide-co-glycolide-co-caprolactone) (PLGC) was synthesized to prepare nanoparticles by the modified spontaneous emulsification solvent diffusion method (modified-SESD method); and the method was also modified by using the Tween60 instead of poly(vinyl alcohol) (PVA) as dispersing agent. The obtained nanoparticles have spherical shape and good particle distribution with mean size in the range from 100 to 200 nm. The in vitro degradation behaviour of PLGC nanoparticles was investigated. It was found that PLGC nanoparticles could remain stable during the degradation with no agglomeration. Compared with PLA and PLGA nanoparticles, the degradation rate of PLGC nanoparticles is faster. After 9 weeks of hydrolysis, the M_n of PLGC is less by 10% of the original M_n. The mean radius of the nanoparticles increases from 68 nm to 80 nm continuously during the first stage, and after 4 weeks of degradation, the particles' size decreases gradually from 80 nm to about 40 nm. These results suggest that the PLGC nanoparticles may show degradation-controlled drug release behaviour and seem to be a promising drug delivery system.     

Preparation, characterization and application of pyrene-loaded methoxy poly(ethylene glycol)–poly(lactic acid) copolymer nanoparticles

Pyrene-loaded biodegradable polymer nanoparticles were prepared by incorporating pyrene into the polymer nanoparticles formulated from amphiphilic diblock copolymer, methoxy poly(ethylene glycol)–poly(lactic acid) (MePEG–PLA). Their morphological structure and physical properties were characterized by nuclear magnetic resonance (NMR), dynamic light scattering, fluorescence spectroscopy, transmission electronic microscopy and zeta potential measurements. Further, MePEG–PLA nanoparticles containing pyrene as fluorescent marker were administered intranasally to rats, and the distribution of nanoparticles in the nasal mucosa and the olfactory bulb were visualized by fluorescence microscopy. NMR results confirmed that MePEG–PLA copolymer can form nanoparticles in water, and hydrophilic PEG chains were located on the surface of the nanoparticles. The particle size, zeta potential and pyrene loading efficiency of MePEG–PLA nanoparticles were dependent on the PLA block content in the copolymer. Following nasal administration, the absorption of nanoparticles across the epithelium was rapid, with fluorescence observed in the olfactory bulb at 5 min, and a higher level of fluorescence persisted in the olfactory mucosa than that in the respiratory mucosa. These results show that pyrene could serve as a useful fluorescence probe for incorporation into polymer nanoparticles to study tissue distribution and MePEG–PLA nanoparticles might have a great potential as carriers of hydrophobic drugs.     

Preparation of PLA-based nanocomposites modified by nano-attapulgite with good toughness-strength balance

Polylactic acid (PLA) was modified by poly (butylene adipate-co-terephthalate) (PBAT) and nano-attapulgite (AT) using the melt blending technique. Ethylene-butyl acrylate-glycidyl methacrylate (E-BA-GMA) was used as a compatibilizer which can bond the AT nanoparticles with PLA/PBAT matrix by interaction between the epoxy and hydroxyl groups. The effects of the AT content on the mechanical properties, thermal properties, crystallinity and morphology of PLA/PBAT/ATT nanocomposites were investigated. The results showed that the tensile strength, elongation at break and impact strength of PLA/PBAT could be simultaneously increased by incorporating AT nanoparticles. PLA/PBAT/AT nanocomposites possessed higher thermal stability than pure PLA/PBAT. In the ternary composite system of PLA/PBAT/AT, AT acted as a heterogeneous nucleating agent and was able to increase the crystallization temperature. When the AT content was low (≤2.5 wt%), AT nanoparticles could uniformly disperse in the PLA/PBAT matrix. In general, AT was an effective filler to reinforce and toughen PLA/PBAT blend simultaneously, and the PLA/PBAT/AT nanocomposite with 2.5 wt% AT exhibited a good combination of strength and toughness.     

ZnO nanoparticles as chain elasticity reducer and structural elasticity enhancer: Correlating the degradating role and localization of ZnO with the morphological and mechanical properties of PLA/PP/ZnO nanocomposite

The main purpose of this study was to investigate the effect of zinc oxide (ZnO) nanoparticles on the morphological, mechanical, thermal, and rheological properties of PLA/PP blend. In this regard, nanocomposites containing 1, 3, and 5 wt% of ZnO nanoparticles were prepared by melt mixing. In addition, three different mixing procedures were adopted to study their effects on the microstructure of nanocomposites. The rheological behaviors demonstrated a higher elasticity and less compatibility for two phases in the case of nanocomposites containing nanoparticles in harmony with the morphological observations. Accordingly, it was correlated to the elasticity originating from the interphase, anticipated coalescence of dispersed particles as a result of degradation of PLA chains triggered by ZnO nanoparticles (ZnO‐NPs) and also agglomeration of ZnO‐NPs depending on the content of nanoparticles and chosen mixing procedure. It was also found that mixing method puts a remarkable influence on the microstructure and rheological behavior of nanocomposites. Results of mechanical characterizations and thermogravimetric analysis (TGA) also confirmed the degradation induced by ZnO nanoparticles.     

Improving the impact property and heat‐resistance of PLA/PC blends through coupling molecular chains at the interface

The influences of both the molecular structure and the melt viscosity differences between Poly(lactic acid) (PLA) and polycarbonate (PC) on the interpenetration of molecular chains at the interface were investigated by comparing the dynamic mechanical properties and morphologies of the as‐prepared PLA/PC solution‐casting blends with those of their corresponding annealed (180°C, 8 h) samples or PLA/PC melt blends. Additionally, two chain extenders containing epoxy groups (ADR and TGDDM) were used to improve the interfacial strength. Subsequently, the interpenetration of PLA and PC molecular chains at the interface was also surveyed. Finally, the effects of the morphology formed by after adding ADR or TGDDM on the impact property, and heat resistance were discussed. The results showed that there was no interpenetration of molecular chains at the interface in PLA/PC melt blends because of the serious hindrance of the molecular structure and the melt viscosity differences. Although the interfacial strength achieved significant increase after adding ADR or TGDDM, the increase of the interfacial strength should be caused by the connection of ADR or TGDDM molecules with PLA and PC molecules at the interface through chemical bonds rather than the entanglements of PLA and PC molecular chains because of no interpenetration of PLA and PC molecular chains at the interface. Thus, the morphology formed after adding ADR or TGDDM is still the type of complete phase separation, which may be the most suitable morphology for achieving high impact and heat resistance PLA/PC blends because these two properties strongly depend on the crystallinity of PLA phase. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis,characterization, and hydrolytic degradation of polylactide/poly(ϵ-caprolactone)/nano-silica composites

Poly(lactic acid) (PLA)/poly(?-caprolactone) (PCL)/nano-silica composite degradable films were prepared by a solvent casting method. SEM results showed that the nano-silica particles were dispersed uniformly in the PLA/PCL matrix. TGA results indicated that the thermal decomposition temperature rose with the increase of nano-silica content. The tensile strength of the composites was enhanced with the increase of nano-silica content up to 2%. The tensile strength increased with the silica content and reached its maximum (22.51 Mpa). The improvement in the water uptake ratio in the PLA/PCL/silica nanocomposites may be attributable to the presence of silica nanoparticles in the PLA/PCL matrix. After 15 weeks total processing time for the solution of alkaline and phosphate buffer, the performances of 16.23% and 3.65% for degradation.     

Electrostatic attachment of gold and poly(lactic acid) nanoparticles onto omega-aminoalkanoic acid self-assembled monolayers on 316L stainless steel

The assembly of poly(lactic acid) (PLA) nanoparticles on a 12-aminodecanoic acid (ADA) self-assembled monolayer (SAM) is described. Assembly is accomplished through electrostatic interactions between the positively charged SAM and the negatively charged PLA nanoparticles. The strategy used involves two steps in which a preliminary electrochemical coating of the ADA SAM is followed by a second step that involves immersing the SAM in a solution containing gold or PLA nanoparticles. The SAM was characterized by using cyclic voltammetry (CV), X-ray photoelectron spectroscopy (XPS), FTIR spectroscopy, and contact angle measurements, whereas scanning electron microscopy (SEM) was used to image the nanoparticles after electrostatic attachment was achieved. We found that the surface coverage of the nanoparticles could be controlled by modulating the electrostatic interactions between the negatively charged particles and the positively charged SAM surface by varying the pH of the nanoparticle solution, the immersion time, and the number of cyclic voltammetry scans under which the SAM was formed.     

Layer-by-layer polyelectrolyte coating of low molecular weight poly(lactic acid) nanoparticles

Low molecular weight (M(w)) poly(L-lactic acid) (PLA) nanoparticles were coated with polyelectrolytes (PEs) by layer-by-layer (LbL) technique using a filtration approach. Poly(allylamine hydrochloride) and poly(sodium 4-styrenesulfonate) were applied as PEs in coating. LbL coating is aimed to use in producing (nano)particulate drug delivery systems with improved biocompatibility and sustained or targeted release of drug substances. Nanoparticles of rapidly biodegradable polymers, like the low M(w) PLA, open up a possibility to control the release of the encapsulated substance by the coating, but set challenges to the coating process due to increased aggregation tendency and degradation rate of the polymer. When the core PLA nanoparticles were prepared by nanoprecipitation, surface properties of the nanoparticles were affected by solvent selection. Successful LbL coating of the PLA nanoparticles was obtained only with chloroform, but not with dichloromethane as the solvent during nanoprecipitation. Reason for this was found to be the more charged surface of the nanoparticles prepared with chloroform compared to the nanoparticles prepared with dichloromethane.     

The synergistic reinforcing effects of halloysite nanotube particles and polyolefin elastomer-grafted-maleic anhydride compatibilizer on melt and solid viscoelastic properties of polylactic acid/ polyolefin elastomer blends

The effect of halloysite nanotube (HNTs) particles and polyolefin elastomer-graft-maleic anhydride (POE-g-MA) in the polylactic acid (PLA) and polyolefin elastomer (POE) blend with a constant weight percentage composition have been studied using the scanning electron microscopy, rheometry, dynamic mechanical thermal analysis (DMTA) as well as the thermogravimetric testing. Through these, it was found that the simultaneous presence of POE-g-MA and HNT significantly improves the melt and solid viscoelastic properties and thermal stability of PLA/POE. This improvement is attributed to the increased interactions and improved interfacial adhesion between the present components. The microscopic images of PLA/POE-g-MA/POE (80/8/12) blend containing 4 wt% HNT showed a microstructure similar to the interconnected morphology due to the enhanced compatibility and better dispersion of nanoparticles. The rheological behavior was significantly changed for the PLA/POE blend containing POE-g-MA and 4 wt% HNT. This dramatic increase in the rheological properties was consistent with the morphological results. Only one glass transition temperature was observed in the DMTA plot of PLA/POE-g-MA/POE blend, which was a sign of a homogeneous, fully compatible system. In addition, a very strong reinforcing effect of HNT particles was observed in the presence of POE-g-MA for the nanocomposites. Finally, the thermogravimetric analysis showed a completely different trend for thermal degradation of PLA/POE-g-MA/POE nanocomposite containing 4 wt% HNT, which could be an indication of microstructural development.     

Composite Fiber Spun Mat Synthesis and In Vitro Biocompatibility for Guide Tissue Engineering

Composite scaffolds are commonly used strategies and materials employed to achieve similar analogs of bone tissue. This study aims to fabricate 10% wt polylactic acid (PLA) composite fiber scaffolds by the air-jet spinning technique (AJS) doped with 0.5 or 0.1 g of zirconium oxide nanoparticles (ZrO₂) for guide bone tissue engineering. ZrO₂ nanoparticles were obtained by the hydrothermal method and characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). SEM and fourier-transform infrared spectroscopy (FTIR) analyzed the synthesized PLA/ZrO₂ fiber scaffolds. The in vitro biocompatibility and bioactivity of the PLA/ZrO₂ were studied using human fetal osteoblast cells. Our results showed that the hydrothermal technique allowed ZrO₂ nanoparticles to be obtained. SEM analysis showed that PLA/ZrO₂ composite has a fiber diameter of 395 nm, and the FITR spectra confirmed that the scaffolds’ chemical characteristics are not affected by the synthesized technique. In vitro studies demonstrated that PLA/ZrO₂ scaffolds increased cell adhesion, cellular proliferation, and biomineralization of osteoblasts. In conclusion, the PLA/ZrO₂ scaffolds are bioactive, improve osteoblasts behavior, and can be used in tissue bone engineering applications.     

Pyrolysis-GC-MS reveals important differences in hydrolytic degradation process of wood flour and rice bran filled polylactide composites

Pyrolysis-GC-MS of polylactide (PLA) biocomposites before and after hydrolytic degradation revealed prominent differences in the hydrolytic degradation process of rice bran and wood flour filled biocomposites. The water uptake and mass loss for polylactide/wood flour composites were similar to that of plain PLA. Pyrolysis-GC-MS, however, showed that on prolonged ageing the hydrolysis of PLA led to increased wood flour concentration in the remaining biocomposite matrices. In contrast, the polylactide/rice bran composites exhibited larger water uptake and higher mass loss. Pyrolysis-GC-MS and FTIR analysis proved that the higher mass loss was caused by migration of rice bran from the composites. The type of natural filler could thus greatly influence the degradation process and/or the stability of the materials in aqueous or humid environments.     

Cationic PLA nanoparticles for DNA delivery: comparison of three surface polycations for DNA binding, protection and transfection properties

Biodegradable cationic nanoparticles (cNP) made of poly(lactide) (PLA) have been shown to be promising carrier systems for in vivo DNA delivery and immunization. In previous work, we have described a versatile approach for the elaboration of cationic PLA cNP based on the use of pre-formed particles and subsequent adsorption of a model polycation, the poly(ethylenimine) (PEI). Here, we evaluated two more polycations, chitosan and poly(2-dimethyl-amino)ethyl methacrylate (pDMAEMA)) to determine the most suitable one for the development of PLA cNP as DNA carriers. Cationic PLA-PEI, PLA-chitosan and PLA-pDMAEMA nanoparticles were compared for interaction with plasmid DNA and, more importantly, with regards to the biological properties of bound DNA. pDMAEMA coating yielded the most positively charged nanoparticles with the highest DNA binding capacity (32 mg/g). Loaded with DNA, all three cNP were in the same size range ( approximately 500 nm) and had a negative zeta potential (-50 mV). PLA-chitosan was the only cNP that released DNA at pH 7; the two others required higher pH. Adsorption and release from cNP did not alter structural and functional integrity of plasmid DNA. Moreover, DNA coated onto cNP was partially protected from nuclease degradation, although this protection was less efficient for PLA-chitosan than others. The highest transfection efficiency in cell culture was obtained with PLA-pDMAEMA carriers. We have shown that at least three different cationic polymers (chitosan, PEI, pDMAEMA) can be used for the production of PLA-based particulate DNA carriers and most probably other cationic polymers can also be used in the same purpose. PLA-pDMAEMA cNP were the most promising system for DNA delivery in this in vitro study. Our future work will focus on the in vivo evaluation of these gene delivery systems.     

Effect of Compatibilizer and Nucleation Agent on the Properties of Poly(lactic acid)/Polycarbonate (PLA/PC) Blends

Poly(lactic acid) (PLA) and polycarbonate (PC) blends were prepared by melt processing with a twin-screw extruder. Ethylene-maleic anhydride-glycidyl methacrylate terpolymer (EMG) as compatibilizer and talc as nucleation agent were added in PLA/PC blends. The effect of EMG and talc on the mechanical properties including tensile, flexural, Izod notched impact properties and heat deflection temperature (HDT) of PLA/PC blends were investigated. The morphologies were observed by scanning electron microscopy (SEM). The crystalline behavior of PLA/PC blends was analyzed by differential scanning calorimetry (DSC) and X-ray diffraction (XRD). The nanoscale mechanical properties of PLA/PC blends were investigated by atomic force microscope (AFM). The results showed that the addition of EMG and talc simultaneously with annealing treatment is the most effective process.     

交联度对原位聚合法制备聚合物胶束性质的影响及相应的空心球制备

用原位聚合法成功地制备出不同响应温度的温敏性聚乳酸/聚(异丙基丙烯酰胺-co-丙烯酰胺)[P(D,L-LA)/P(NIPAM-co-AM)]核壳胶束. 实验中发现, 壳层的交联剂含量对粒子的尺寸有很大的影响, 当交联剂的摩尔分数从5%提高到15%时, 粒子在25 ℃时的流体力学直径从170.2 nm增加到886.5 nm. 通过对胶束粒子的核进行生物降解, 方便地得到了相应的空心球. 用FTIR监测核的降解过程, 用SEM和AFM检测核降解完全后粒子的外在形貌和内在结构变化. DLS结果表明, 空心球粒子同样具有良好的温度响应性, 其响应温度可通过改变原位聚合时单体AM的含量加以调节.     

Poly(lactic acid)-based biocomposites reinforced with modified cellulose nanocrystals

This work investigates reinforcing poly(lactic acid) (PLA) nanocomposites using triazine derivative-grafted cellulose nanocrystals (CNCs). A hydrophobic triazine derivative was synthesized and applied to modify CNCs to improve their thermal stability and diminish the hydrophilicity of the nanoparticles. CNCs before and after modification were used to reinforce PLA nanocomposites by a hot compression process. The results of thermogravimetric analysis indicated that the initial thermal decomposition temperature of modified nanocrystals was improved by approximately 100 °C compared to the original CNCs. That is, the thermal stability of modified cellulose nanocrystals was improved due to the shielding effect of CNCs by a hydrophobic aliphatic amine layer on the surface of the nanoparticles. The results of dynamic contact angle measurements revealed a decrease of hydrophilicity of the modified CNCs. The results from scanning electron microscopy and a UV–Vis spectrophotometer revealed that the compatibility between the modified nanocrystals and the PLA was improved. Finally, the results of tensile tests indicated a significant improvement in terms of breaking strength and elongation at the break point.     

Structure and wettability relationship of coelectrospun poly (L‐lactic acid)/gelatin composite fibrous mats

Coelectrospun polylactide(PLA)/gelatin (GE) composite fibrous matrixes have been identified to exhibit much improved performances compared to the respective components; however, the reasons for their water contact angles decreasing to zero at proper PLA/GE ratios remain unclear. To get a deep understanding of the phenomenon, PLA and GE were coelectrospun with different PLA/GE ratios in this study. Although the resulting composite fibers were homogeneous in appearance, they were detected different microscopic structures by transmission electron mircroscope (TEM) and via morphological observations after selective removal of either PLA or GE component. Together with the results of degradation study in phosphate buffered solution, a kind of cocontinuous phase separation microstructure could be identified for the PLA(50 wt%)/GE(50 wt%) composite fibers, which also showed the water contact angle of 0°. This value was far lower than those of electrospun PLA (～123°) and GE (～42°) fibrous matrixes. The X‐ray photoelectron spectrometry (XPS) data revealed that the polar side groups of protein macromolecules have moved toward composite fiber surface with solvent evaporation during electrospinning, due to the hydrophobic interaction between PLA and GE. Then the excellent hydrophilicity of PLA(50 wt%)/GE(50 wt%) composite fibers could be suggested as the consequence of: (1) the cocontinuous phase separation structure could provide more interface and void for water molecules penetrating; and (2) the accumulation of polar groups on composite fiber surface significantly increased the surface wettability. Copyright © 2010 John Wiley & Sons, Ltd.