电感耦合等离子体原子发射光谱(ICP-AES)法测定人发中铜、锌、钙、镁、铁

样品经硝酸-高氯酸消化溶解,高氯酸冒烟,盐酸溶解盐类后,在盐酸(5%)介质中,在选定的测定条件下,用电感耦合等离子体原子发射光谱(ICP-AES)法测定人发中微量元素铜、锌、铁、镁、钙。选择Cu 327.3、Zn 206.2、Fe 238.2、Mg 279.5、Ca 315.8nm分别作为铜、锌、铁、镁、钙的分析线与混合标准溶液同时测定;方法加标回收率为98.6%～101%,铜、锌、铁、镁、钙的精密度(RSD,n=8)为0.37%～2%,准确度(RE)为-3.4%～1.15%,检出限分别为0.002 3、0.001 6、0.004 6、0.003 0、0.001 4μg/mL。方法克服了分光光度法和原子吸收光谱法操作繁琐、周期长、成本高、灵敏度低等缺点。用于测定人发样品中的铜、锌、铁、镁、钙元素,测定结果与原子吸收光谱法测定值基本一致。经GBWO7061标准物质和自制标样分析验证,测定值与标准值吻合,结果准确可靠。     

ICP-AES法测定红土镍矿中镍、钙、钛、锰、铜、钴、铬、锌与磷的含量

建立了ICP-AES法测定红土镍矿中Ni;Ca;Ti;Mn;Cu;Co;Cr;Zn和P含量的方法。样品用HCl、HNO3溶解,加入HF和HClO4,加热至HClO4烟冒尽,用HCl溶解盐类,过滤,采用ICP-AES法同时测定滤液中Ni、Ca、Mn、Cu、Co、Zn、P;残渣经灼烧、挥硅、K2S2O7熔融、HCl浸取,所得溶液与滤液合并,测定溶液中Cr和Ti含量。方法检出限:P为0.022μg/mL,其它元素在0.0032～0.0085μg/mL之间,方法的精密度(n=7)在1.4%～2.9%之间。分析结果与分光光度法、XRF法和AAS法分析结果的相对误差:Ni、Cu、Co、Cr小于5%,Ti和Mn小于10%,Zn小于15%,Ca和P小于19%。     

ICP-AES法测定铜镍矿、铅锌矿中铜、镍、铅、锌、钴

用电感耦合等离子体发射光谱法测定铜镍矿、铅锌矿石中铜、镍、铅、锌、钴,样品用盐酸-硝酸溶解,在选定的测量条件下以ICP-AES测定溶液中的Cu、Pb、Zn、Co、Ni的含量.对国家一级标准物质进行测定,方法精密度(RSD,n=12)为Cu 2.92%～6.62%,Pb 1.88%～2.61%,Zn 1.30%～2.05%,Co 6.90%,Ni 2.23%.本方法具有线性范围宽、干扰少、快速、简便、检出限低等优点.用于实际使用,结果满意.     

电感耦合等离子体原子发射光谱法(ICP-AES)测定铜磁铁矿中铜、锰、铝、钙、镁、钛和磷的含量

通过样品处理、干扰实验、方法检出限、准确度和精密度实验,确定了最佳实验条件,建立了电感耦合等离子体-原子发射光谱法(ICP-AES)测定铜磁铁矿中铜、锰、铝、钙、镁、钛和磷含量的方法。试料经盐酸、硝酸、氢氟酸、高氯酸分解,用盐酸溶解盐类,过滤,采用电感耦合等离子体原子发射光谱法同时测定滤液中铜、锰、铝、钙、镁、钛和磷的含量。方法检出限为锰、钛和磷小于0.00085%,其它元素小于0.0054%,分析结果与分光光度法、X射线荧光光谱法(XRF)和原子吸收光谱法(AAS)分析结果一致,8个实验室对5个水平样品进行协同实验给出了方法的精密度。     

微波灰化-电感耦合等离子体原子发射光谱法测定原油中的金属元素

采用微波灰化技术消化原油样品,并使用电感耦合等离子体原子发射光谱法(ICP-AES)测定其中Na、Mg、Ca、Fe、V、Ni和Cu的含量。探讨了原油样品中金属元素测定的称样量和微波灰化程序,并优化了仪器工作参数和实验条件。样品经微波灰化处理后,用盐酸溶解残渣,方法对Na、Mg、Ca、Fe、V、Ni和Cu元素的检出限分别为0.07、0.01、0.01、0.01、0.02、0.04和0.03mg/kg,回收率在84.5%～96.6%之间,相对标准偏差在2.1%～6.9%范围。方法简便、可靠,可用于原油中Na、Mg、Ca、Fe、V、Ni和Cu 7种金属元素的检测。     

ICP-AES法测定AuNiGd合金中的Ni、Gd、Pd、Fe和Bi

报道了采用ICP-AES法测定AuNiGd合金中Ni、 Gd、 Pd、 Fe、 Bi.对测定元素的波长、测定条件进行了选择;考察了基体和无机酸对测定的影响;在优化条件下,对试样进行测定,其相对标准偏差(n＝15) Ni 1.6%、 Gd 1.8%、 Pd 13%、 Fe 4.9%、 Bi 13%;回收率 Ni 98%～105%、 Gd 97%～99%、 Pd 101%～105%、 Fe 98%～104%、 Bi 104%～106%.     

电感耦合等离子体原子发射光谱(ICP-AES)法测定铜砷滤饼中的Pb、Fe、Bi三种元素

采用硝酸、盐酸、氢氟酸、高氯酸分解样品,氢溴酸-盐酸挥发消除砷基体,优化仪器测定参数,选取最佳工作条件,建立了电感耦合等离子体原子发射光谱(ICP-AES)法测定铜砷滤饼中Pb、Fe、Bi元素的分析方法,其测定范围分别为:0.12%～2.09%;0.081%～2.10%;1.20%～6.14%。各元素检出限为0.010 0.006、0.003μg/mL。加标回收率分别为95.5%～102%。方法简便、准确、可靠,适用于铜砷滤饼中Pb、Fe、Bi元素的同时测定。     

电感耦合等离子体质谱法测定镁合金中的多种元素

用电感耦合等离子体质谱(ICP-MS)法测定了镁合金中的Be、Al、Ca、Fe、Mn、Ni、Cu、Zn、Ag、Cd、Sn、La、Ce、Pb14种元素,进行了稳定性实验以及Cu、Zn、Ni、Mg、Al基体实验,考察了共存元素的干扰.镁合金标准物质测定值与参考值符合较好,方法检出限为0.0002～0.3346 μg/g,相对标准偏差RSD＜10%.     

茶叶中锰、铁、锌、铬等10种微量元素的快速测定

茶叶样品经粉碎干燥后,以硝酸-高氯酸混合液进行消解处理,火焰原子吸收分光光度法测定了K、Ca、Na、Mg、Fe、Mn、Cu、Zn、Ni、Cr的含量。结果表明,回收率在89.30%～103.20%之间,相对标准偏差小于10%。方法简单、快速、经济,结果可靠。     

黄芪及其水煎液中Cu、Mn、Zn、Fe、Se的测定和浸出率研究

用原子吸收法对黄芪及其水煎液中的Cu、Mn、Zn、Fe进行了测定 ,用紫外分光光度法测定了其中的Se ,从而得出各元素的浸出率。结果表明五种元素的浸出率为 :Cu >Zn >Mn >Se >Fe。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.