Synthesis of Zn‐doped talc in hydrothermal atmosphere

Zn‐doped talc were synthesized under hydrothermal conditions at constant reaction time and pressure of 160 hours and 2 kbar respectively, at three different temperatures (300, 500 and 650 °C) with pH‐values of 5 and 7. The starting materials and run products were characterized by X‐ray powder diffraction (XRPD), scanning electron microscopy with annexed energy‐dispersive spectrometry (SEM‐EDS), differential scanning calorimetry thermogravimetric analysis (DSC‐TG) and Fourier transform infrared (FT‐IR). The results showed that the temperature, pH‐value of the reaction mixture and amount of zinc in the starting mixture affected the growth of the Zn‐doped talc. When synthesized at low temperature talc presents low crystallinity, flawed morphology but higher content in zinc in its lattice. A thermal treatment at, or above 500 °C allowed a significant flaw reduction in talc morphology, a higher crystallinity and a lower content in dopant. When large amounts of Zn were present in the starting mixtures, Zn‐doped talc grew small in size and poorly shaped. The effect of Zn doping on some chemical/physical characteristics of the synthesized talc was also discussed.     

Synthesis and growth mechanism of ZnO rod‐like nanostructures by a microwave‐assisted low‐temperature aqueous solution route

A zinc oxide (ZnO) nanoarray (rod‐like nanostructure) was successfully synthesized through a low‐temperature aqueous solution and microwave‐assisted synthesis using zinc nitrate hexahydrate (Zn(NO₃)₂·6H₂O) and hexamethylenetetramine (HMTA) as raw materials, and using FTO glass as substrate. The effects of parameters in the preparation process, such as solution concentration, reaction temperature and microwave power, on the morphology and microstructure of ZnO nanoarray were studied. Phase structure and morphology of the products were characterized by X‐ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. The results indicated that hexagonal wurtzite structure ZnO nanoarray with good crystallization could be prepared through a low‐temperature solution method. When the concentration of the mixed solution was 0.05 M, the reaction temperature was 95 °C, and the reaction time was 4 h, high‐density ZnO regular nanorods of 200 nm diameter were obtained. A possible mechanism with different synthesis methods and the influence of microwave processing are also proposed in this paper.     

Catalyst‐free thermally‐evaporated growth and optical properties of ZnO nanowires on Si,GaN and sapphire substrates

Vertically well‐aligned zinc oxide nanowires (NWs) with high density were successfully synthesized on Si, sapphire and GaN/sapphire substrates by thermal evaporation of zinc powders without catalysts or additives. The growth behavior of ZnO NWs was strongly dependent on the substrate materials. The effects of the substrate position on the structures and properties of ZnO NWs were primarily discussed. The morphology and crystallinity of the resultant NWs were studied by scanning electron microscope, transmission electronic microscope and X‐ray diffraction. The photoluminescence (PL) characteristics of the ZnO NWs on the different substrates were studied. The results showed that the as‐grown ZnO NWs exhibit a sharp and strong ultraviolet emission at 3.27 eV and a very weak green emission at around 2.48 eV, indicating that the a‐synthesized NWs have excellent PL properties with good crystalline quality and can be an ideal candidate for making luminescent devices. By comparison of PL spectra, we revealed that the green‐to‐UV emission intensity ratios were considerably dependent on the substrate materials, which was explained by the difference in the structural morphology of the produced nanowires.     

Phase‐selective crystallization of nickel phosphate VSB‐5 with (2‐hydroxyethyl) trimethylammonium hydroxide as template

Several nickel phosphate molecular sieves were synthesized by conventional heating (CH) and microwave assisted hydrothermal (MAH). Nickel phosphate VSB‐5 (Versailles Santa Barbara‐5) was synthesized with conventional oven for 72 h or with microwave for 1 h and followed by conventional oven for 48 h in the presence of (2‐hydroxyethyl) trimethylammonium hydroxide as template. The phase transformation is observed by variation of CH time for the synthesis of nickel phosphate molecular sieves. At CH time of 24 h, the VSB‐5 crystal together α‐Ni₂P₂O₇, Ni₂P₄O₁₂ and unknown phases were produced but the pure VSB‐5 crystal was obtained in the CH time of 48 h or more. At high content of nickel, a mixture of α‐Ni₂P₂O₇, Ni₂P₄O₁₂ phases and small amount of VSB‐5 crystal, was achieved but pure VSB‐5 crystal was obtained in the lower level of nickel and other phases are vanished. An efficient ultrasonic‐assisted aging was found for the synthesis of nickel phosphate molecular sieve, in which by ultrasonic mixing of 0.5 h followed microwave of 1 h, the CH time is significantly reduced from 48 to 24 h. The morphology of nickel phosphate crystals is highly influenced in the presence of ethylene glycol as co‐solvent. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Facile morphology‐controlled hydrothermal synthesis of flower‐like self‐organized ZnO architectures

Flower‐like self‐organized crystalline ZnO architectures were obtained through a facile and controlled hydrothermal process. As‐synthesized products were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), high‐resolution transmission electron microscopy (HRTEM), X‐ray diffraction (XRD), electron diffraction and UV‐Vis spectroscopy. XRD and electron diffraction results confirmed the obtained materials are pure wurtzite ZnO. The effects of different ratios of starting materials and solvent on the morphologies of ZnO hydrothermal products were also evaluated by SEM observations. It is suggested that the use of water, rather than ethanol as the solvent, as well as employing a precursor of Zn(Ac)₂ and 2NaOH (v/v) in hydrothermal reactions are responsible for the generation of specific flower‐like self‐assembled ZnO structures. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Capsule‐like α‐Fe2O3 nanoparticles: Synthesis,characterization, and growth mechanism

Uniform capsule‐like α‐Fe₂O₃ particles were synthesized via a simple hydrothermal method, employing FeCl₃ and CH₃COONa as the precursors and sodium dodecyl sulfate (SDS) as soft template. X‐ray powder diffraction (XRD), field emission scanning electron microscopy (FE‐SEM), transmission electron microscopy (TEM), and high‐resolution transmission electron microscopy were used to characterize the structure of synthesized products. Some factors influencing the formation of capsule‐like α‐Fe₂O₃ particles were systematically investigated, including different kinds of surfactants, the concentration of SDS, and reaction times. The investigation on the evolution formation reveals that SDS was critical to control the morphology of final products, and a possible five‐step growth mechanism was presented by tracking the structures of the products at different reaction stages.     

Intermediates and transport phenomena in two‐temperature synthesis of ZnGeP2

High quality semiconducting ternary compound ZnGeP₂ was synthesized by a modified two‐temperature technique using high purity elemental zinc, germanium and phosphorus as the starting materials. Transport phenomena of zinc and phosphorus vapors and the major reaction intermediates, taking place in ZnGeP₂ formation, were studied by interrupting the synthesis process using quenching technique as well as by adjusting the temperatures of cold and hot zones. The powder X‐ray diffraction analysis showed that the major reaction intermediates were ZnP₂, Zn₃P₂, and GeP, which proportions were changed at the different temperature stages. ZnP₂ was formed in the temperature gradient region and ZnGeP₂ was formed in the hot zone when the temperature of the hot zone was higher than 900 °C. The 520‐1040 °C temperature profile was chosen for the ZnGeP₂ synthesis and charge amount per run reached 200 g. The powder X‐ray diffraction pattern of the synthesized ZnGeP₂ compound was in agreement with the standard pattern of ZnGeP₂. These results demonstrated that the synthesized ZnGeP₂ compound was a single phase. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Different copper oxide nanostructures: Synthesis,characterization, and application for C‐N cross‐coupling catalysis

Cupric oxide and cuprous oxide micro‐/nanomaterials with well‐controlled sizes and morphologies have been synthesized via different crystal growth techniques. Structural and morphological characterizations of these copper oxide micro‐/nanomaterials were performed by X‐ray powder diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). After that, these copper oxide micro‐/nanomaterials were used as catalysts for a typical C‐N cross‐coupling reaction directly. The catalytic results showed that different copper oxide micro‐/nanomaterials had different catalytic activities in C‐N cross‐coupling reaction. The particle size of cupric oxide and the oxidation state of copper played vital roles in the catalytic process. Cupric oxide with small particle size has the best catalytic activity, while cupric oxide with different morphologies has almost the same yields and cuprous oxide has very poor yields. Further, the possible catalytic mechanism for copper oxide nanomaterials catalyzed cross‐coupling reaction was proposed. And the influence of particle size and oxidation state was carefully discussed. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Preparation of shuttle‐like Sb2S3 nanorod‐bundles via a solvothermal approach under alkaline condition

Uniform shuttle‐like Sb₂S₃ nanorod‐bundles were synthesized via a polyvinylpyrrolidone (PVP) assisted solvothermal approach under alkaline condition, using antimony chloride (SbCl₃) and thiourea (CH₄N₂S, Tu) as the starting materials in ethanol. The phase structure, composition and morphology of the product were characterized by means of X‐ray diffraction (XRD), energy dispersive X‐ray spectrometry (EDS), transmission electron microscopy (TEM), and high‐resolution transmission electron microscopy (HRTEM). XRD and EDS results confirm that the synthesized Sb₂S₃ nanorod‐bundles have an orthorhombic structure and an atomic ratio of 3:2 for S:Sb. TEM and HRTEM results show that the shuttle‐like Sb₂S₃ bundles are composed of nanorods with a size distribution of 20‐40 nm and growing along c‐axis. Furthermore, experiments under different reaction conditions were carried out and the mechanism for the growth of nanorod‐bundles was discussed (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural and magnetic studies of Mn‐doped ZnO

The bulk samples of Mn‐doped ZnO were synthesized with the nominal compositions Zn_1‐xMn_xO (x = 0.02, 0.05, 0.10, 0.15) by the solid‐state reaction and sol‐gel methods. In both the methods the samples were finally sintered at ∼700 °C in air. The X‐ray diffraction (XRD) studies of the samples synthesized by the solid‐state reaction method exhibit the presence of wurtzite (hexagonal) crystal structure similar to the parent compound (ZnO) in all the samples, suggesting that doped Mn ions sit at the regular Zn sites. However, same studies spread over the samples with Mn content ≥5% and synthesized by the sol‐gel method reveal the occurrence of some secondary phase in addition to the majority wurtzite phase. The magnetic measurements by vibrating sample magnetometer (VSM) clearly indicate ferromagnetic interaction at room temperature in all the samples. The Curie temperatures (T_c) and magnetization vary with concentration of Mn ions in the samples. However, the samples synthesized by sol‐gel method were found to have lower Tc values and also lower magnetization as compared to the corresponding samples synthesized by solid‐state reaction method. It could possibly be due to the presence of antiferromagnetic islands and smaller crystallite sizes in the samples prepared by sol‐gel method. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Large‐scale production of well‐dispersed submicro ZrB2 and ZrC powders

ZrB₂ and ZrC powders were synthesized via metallothermic reduction route using ZrO₂, B/C, and Mg as raw materials. Low packing density of the green mixture and high heating temperature of the furnace are crucial for the formation of well‐dispersed submicro powders. Optimum reaction time helped achieve good crystallization and high purity. The as‐prepared samples were characterized by XRD, FESEM, TEM, and particle size analyzer. Results showed that well‐dispersed ZrB₂ powders with mean particle size of 0.534 μm and ZrC powders with mean particle size of 0.376 μm can be obtained. Oxygen content can be controlled lower than 1.0 wt%. The bench‐scale output is about 10 kg/d.     

Synthesis and characterization of 1‐phenyl‐3‐(propan‐2‐yl)‐1H‐pyrazol‐5‐ol single crystals

The synthesis of pyrazoles and its derivatives remains of great interest due to their wide applications in pharmaceutical and agrochemical industry. The 1‐phenyl‐3‐(propan‐2‐yl)‐1H‐pyrazol‐5‐ol was synthesized. The 1‐phenyl‐3‐(propan‐2‐yl)‐1H‐pyrazol‐5‐ol single crystals were grown by slow solvent evaporation technique using mixture of chloroform and methanol as a solvent. Yellowish and transparent crystals having maximum dimensions of 0.005 m × 0.004 m × 0.002 m were grown. The crystals were characterized by powder XRD, FT–IR, TG–DTA–DSC and dielectric study. The crystals remained stable up to 160 °C and then start decomposing. The DSC suggested both endothermic and exothermic reactions. One broad exothermic peak was observed at 558.1 °C due to complete decomposition of the sample into the gaseous phase and reaction within the products. Thermodynamic and Kinetic parameters of decomposition were calculated by Coats–Redfern formula. The dielectric study was carried out in the frequency range from 50 Hz to 5 MHz at room temperature. The dielectric constant decreased as the frequency of the applied field increased. The variations of dielectric loss, a.c. conductivity and a.c. resistivity also studied with the frequency of the applied field. Jonscher's power law was verified for a.c. conductivity.     

Comments and reconciliation of the Ni–Bi‐system thermodynamic reassessments

The binary Ni‐Bi alloys as well as multicomponent materials comprising systems like Ni‐Bi‐Sn, Ni‐Bi‐Sb etc. are recently considered as prospective for design of lead‐free solders. For that reason various authors focused their attention to the Ni‐Bi system thermodynamics. The studies identified five phases in the above system. Two of them (i.e., (Ni) and liquid), were treated as disordered substitutional solutions. The phase NiBi₃ is stoichiometric and a standard two‐sublattice model was repeatedly applied to describe its Gibbs free energy, while for the nonstoichiometric NiBi phase, a three‐sublattice model was retained. The pure bismuth phase ((Bi)) is stoichiometric as well. The results are discussed and compared to literature thermochemical and topological data. In liquid state, strong repulsions between nickel and bismuth atoms are anticipated in the nickel rich‐side, but no data about a liquid phase miscibility gap is available yet. Therefore, the stability of the liquid phase has to be reassured, in spite of positive deviations from ideal behaviour. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Low‐temperature preparation of bismuth ferrite microcrystals by a sol‐gel‐hydrothermal method

Well‐crystallized pure perovskite bismuth ferrite (BiFeO₃) powders with various morphologies have been synthesized by a novel sol‐gel‐hydrothermal route for the first time, which combined the conventional sol‐gel process and the hydrothermal method. The as‐prepared samples were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), differential thermal analysis (DTA) and ferroelectric test system. The results revealed that the compositions, morphological and dimensional changes in bismuth ferrite samples synthesized by sol–gel–hydrothermal method strongly depend on the concentrations of mineralizer. Ferroelectric hysteresis loops are displayed in the BiFeO₃ samples. The bismuth ferrites were hydrothermally synthesized at as low a temperature as 180 °C, which is comparatively lower than that synthesized by the normal sol–gel route. The formation mechanism of the bismuth ferrite crystalline was also discussed. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis of flake‐like crystals by a hydrothermal process

In this study, a hydrothermal method for formation of flake‐like nanocrystals is described. This approach with appropriate surfactant CTAB can be successfully synthesized of compound, noble metals, and semiconductors simple substance, such as lead sulfate, gold and selenium. The products were characterized by SEM image and XRD pattern. The results show that TSA acting as a new class of inorganic scaffolds for the synthesis of materials in crystal engineering and composites design for different applications is versatile reactor and may be extended to the creation of other highly novel inorganic structures with applications in catalysis, novel optical materials and other fields. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Controllable one‐step synthesis of CuO,Cu2O and Cu

In the present report, CuO, Cu₂O and Cu have been successfully synthesized through a facile, one‐step hydrothermal method at a relative low temperature by controlling only the concentration of citric acid. Compared with other synthetic methods, the present method is mild, high‐efficient and nontoxic. The crystal structure and morphology of the as prepared samples were characterized by X‐ray diffraction and scanning electron microscopy, respectively. The mechanism for the crystal phase and morphological changes with different citric acid concentrations were discussed. The possible reaction process of the synthesis was also studied on the basis of the experimental results. We hope that this facile, one‐step hydrothermal method could be used in controlling synthesis of other metals and metal oxides under appropriate experimental conditions.     

Morphology‐photocatalytic properties‐growth mechanism for ZnO nanostructures via microwave‐assisted hydrothermal synthesis

ZnO nanostructures with various morphologies including rod‐like, sheet‐like, needle‐like and flower‐like structures were successfully synthesized via a fast and facile microwave‐assisted hydrothermal process. Reaction temperature, reaction time and the addition of NaOH were adjusted to obtain ZnO with different morphologies. Scanning electron microscopy(SEM), transmission electron microscope(TEM), X‐ray diffraction (XRD) and ultraviolet spectrophotometer (UV) were used to observe the morphology, crystal structure, ultraviolet absorption and photocatalytic activity of the obtained ZnO. The results indicated that growth rate of ZnO nanostructure along [001] direction was more sensitive to temperature compared with those along [101] and [100] directions. The competition between anionic surfactant and OH⁻ played an important role in the formation of ZnO with various morphologies. Flower‐like ZnO had better ultraviolet absorption property and excellent photocatalytic activity than ZnO in the other morphologies. On the basis of the above results, a possible growth mechanism for the formation of ZnO nanostructures with different morphologies was described.     

High‐performance gas‐sensing properties of octahedral NiO crystals prepared via one‐step controllable synthesis route

Octahedrally shaped NiO powders have been synthesized via a one‐step composite‐hydroxide‐mediated method without any surfactant. The synthesized materials are characterized by XRD, EDS, TEM and FESEM techniques. Each particle exhibited a nearly perfect octahedron shape with sharp edges and corners as well as smooth surfaces. The octahedral NiO particles performed better gas‐sensitivity toward ethanol than that of NiO nanopowders, which was attributed to the exposed ｛111｝ facets of octahedron. The result was confirmed by the first‐principle calculation which indicated that the (111) facet was more active than (100) and (110) facet.     

Growth and characterization of 4‐(2‐hydroxyphenylamino)‐pent‐3‐en‐2‐one single crystals

4‐(2‐hydroxyphenylamino)‐pent‐3‐en‐2‐one (HPAP) was synthesized and single crystals were grown by the solution growth technique using methanol as a solvent. The crystals having orthorhombic symmetry were characterized by single crystal XRD, FTIR spectroscopy, NMR spectroscopy, TGA, DSC and dielectric studies. Very less variation in the value of dielectric constant is found for different frequencies of applied field. The crystals were exhibiting positive photoconductivity and poor NLO responses. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis and characterization of hexagonal ferrites BaFe12‐2xZnxTixO19 (0 ≤ x ≤ 2) by thermal decomposition of freeze‐dried precursors

Substituted barium hexaferrites, BaFe_12‐2xZn_xTi_xO₁₉ (0 ≤ x ≤ 2), have been synthesized by thermal decomposition of freeze‐dried acetate precursors. Decomposition and phase formation were investigated by means of thermal analysis, XRD and IR spectroscopy. The initially amorphous decomposed precursor reacts to the substituted hexaferrite via a spinel‐like maghemite (γ‐Fe₂O₃) and Zn/Ti containing spinel ferrites. The synthesis method allows a decrease of the reaction temperature and time, necessary for producing a single phase hexaferrite. At relative low reaction temperatures, the substitution rate x shows remarkable differences at different iron sublattices. For x ≤ 0,8 this selective substitution results in an increase of magnetization as x grows. (© 2003 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)