倾斜度及温度震荡频率对三维多孔介质方腔自然对流换热的影响

对三维多孔介质倾斜方腔内非稳态自然对流换热进行数值研究.腔体右壁面(X=1)保持恒温T₀,左壁面(X=0)基于温度T₀按正弦规律变化,其他所有壁面保持绝热.采用Brinkman扩展达西模型及SIMPLE算法模拟方腔内的流动.方腔沿y轴转动倾角α1的变化范围为0°~90°,沿x轴转动倾角α2的变化范围为0°~45°,无量纲温度震荡频率f的变化范围为5π~90π.详细研究倾角和温度震荡频率对三维方腔自然对流换热的影响.计算结果表明:当倾角α1=46°,α2=45°及温度震荡频率f=45π时,方腔内的换热最强.     

局部热壁面多孔介质方腔内自然对流的数值研究

本文对上下壁面绝热、左侧壁面长度为b的嵌装加热器部分维持恒定温度T_h而剩余部分绝热,且右侧壁面维持恒定温度T_c的多孔介质方腔内的自然对流换热进行了数值研究.在热壁面无量纲长度B=0.5(B=b/L)的条件下,综合研究了左侧壁面受热部分中心距上壁面的无量纲长度D(D=d/L)、Da数、Ra数和孔隙率对腔体内自然对流换热的影响.数值计算结果表明,左侧壁面受热部分位置的不同对腔体内自然对流换热有很大的影响,D在0.6附近取值时,Na数最大.Da数、Ra数对腔体的自然对流换热影响较大,而孔隙率对换热的影响较小.     

底部局部加热多孔介质自然对流传热的格子Boltzmann模拟

运用格子Boltzmann方法研究了底部局部加热多孔介质方腔的自然对流传热.方腔的上壁面为低温热源,下壁面为局部高温热源,左右壁面为绝热条件.重点分析了高温热源位置a及尺寸b对多孔介质方腔自然对流传热性能的影响,提出了平均Nusselt数Nu和位置a及尺寸b的拟合关系式.研究结果表明:高温热源位置及尺寸对多孔介质方腔内自然对流传热性质的影响很大,且存在最佳高温热源位置(a=4/16)和尺寸(b=0.75),以达到最强的对流换热强度(Nu_(max)≈10.35)和最大的对流换热量(Q_(max)≈5.69).     

周期性锯齿型通道内流动和换热研究

用非稳态层流模型对锯齿型通道内周期性充分发展流动与换热进行了数值模拟．Re=600时数值结果已发生明显振荡,而从入口段算起的第9、10个几何周期的平均Nu数与用周期性充分发展条件计算得到的平均Nu数吻合良好;在此基础上,计算通道周期长度L与通道垂直高度b的比值及通道倾角α等几何结构尺寸对周期性充分发展流动和换热的影响,计算结果表明,增大α和减小L／b都易促使流动产生涡旋,从而增强换热．     

管外包覆多孔介质强化换热的数值研究

本文对管外包覆多孔介质的无限长圆管绕流的流场和温度场进行数值模拟,研究了多孔介质层的无量纲厚度ep,达西数D_a以及雷诺数Re对流动和强制对流换热特性的影响。研究结果表明,管外包覆多孔介质后的强制对流换热效果明显强于光管条件下的效果,换热增强了2.8~5.4倍;壁面平均努塞尔数Nu随e_p和Re的增大而增大,随Da的增大而减小;管壁处的流动阻力系数C_D随ep的增大而增大,随D_a的减小,先增大后减小,当Da小于1×10~(-5)时,阻力系数保持不变。     

复杂多孔介质腔体内自然对流换热的数值研究

采用曲线坐标系下压力与速度耦合的SIMPLEC算法,数值研究复杂多孔介质腔体内的自然对流换热问题.腔体的曲面温度分别保持恒定,上下表面绝热.在曲线坐标系中用有限容积法离散方程,并采用Brinkman扩展达西模型及局部非热平衡模型求解,综合研究Rayleigh数,Darcy数、孔隙率等参数对腔体内自然对流换热的影响.计算结果表明:Rayleigh数和Darcy数的影响最大而孔隙率的影响很小,同时存在使得腔体内换热达到最强的最佳纵横比.     

微细多孔介质中对流换热研究

本文对空气、氦气和二氧化碳流过微细多孔介质内部的对流换热进行了实验研究和数值模拟。实验段为烧结多孔介质,颗粒的平均直径为40～225μm,通过单吹法的实验方法进行瞬态实验,得到了多孔介质内部对流换热系数。数值模拟了气体流过微细多孔结构内部的对流换热的非稳态过程,得到多孔介质内部对流换热系数。数值结果与实验结果基本一致,并与已有结果基本吻合。     

水平板自然对流换热的非线性特性

采用SIMPLE算法,QUICK差分方案,对封闭方腔内水平板自然对流换热进行了数值模拟.数值结果显示,低Ra数时流动和换热处于稳态,当Rayleigh数超过某一临界值时,流动和换热就会发生非稳态振荡,此时流动和换热表现出非对称性.对不同Rayleigh数,流动和换热通过单周期分岔从稳态过渡到非稳态,并通过倍周期分岔过渡到混沌.在混沌区,仍然会出现周期性窗口,并且数值结果与初始条件有关.     

三维有序排列多孔介质对流换热的数值研究

利用CFD软件数值研究了颗粒三维有序堆积多孔介质的对流换热问题. 采用颗粒直径分别为14 mm,9.4 mm和7 mm的球形颗粒有序排列构成多孔介质骨架,在多孔骨架的上方有一恒热流密度的铜板. 采用流固耦合的方法研究了槽通道内温度分布和局部对流换热系数的分布以及对流换热的影响因素. 研究结果表明:热渗透的厚度和温度边界层的厚度在流动方向上逐渐增大,并且随流量的增加而减小;当骨架的导热系数比较高时,对流换热随颗粒直径的减小而略有增大;对流换热系数随聚丙烯酰胺溶液浓度的增大而减小,黏性耗散减弱了对流换热. 关键词： 多孔介质 温度场 局部对流换热系数 数值模拟     

周期性矩形槽通道内对流换热的振荡

采用非稳态数学模型,通过数值模拟对周期性矩型槽通道内流动和换热的振荡特性进行了研究。结果表明:随着Re的增大,对流换热从入口后某一个几何周期开始振荡,振幅沿着通道逐渐增加,并经过若干周期后振幅基本不变;对于不同的Re开始振荡的几何周期数不同;当振幅基本不变时,各几何周期的平均Nu及相应点的速度按时间的平均值基本相等,表明振荡的流动和换热特征参数的时均值仍然具有周期性充分发展的特征;通道中突出物高度对振荡有显著影响,突出部分越高,开始振荡的几何周期数越小。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.