HOMs simulation and measurement results of IHEP02 cavity

In accelerator RF cavities, there exists not only the fundamental mode which is used to accelerate the beam, but also higher order modes(HOMs). The higher order modes excited by the beam can seriously affect beam quality, especially for the higher R/Q modes. 1.3 GHz low-loss 9-cell superconducting cavity as a candidate for ILC high gradient cavity, the properties of higher order mode has not been studied carefully. IHEP based on existing low loss cavity, designed and developed a large grain size 1.3 GHz low-loss 9-cell superconducting cavity(IHEP02cavity). The higher order mode coupler of IHEP02 used TESLA coupler's design. As a result of the limitation of the mechanical design, the distance between higher order mode coupler and end cell is larger than TESLA cavity.This paper reports on measured results of higher order modes in the IHEP02 1.3 GHz low-loss 9-cell superconducting cavity. Using different methods, Q e of the dangerous modes passbands have been obtained. The results are compared with TESLA cavity results. R/Q of the first three passbands have also been obtained by simulation and compared with the results of the TESLA cavity.     

A coaxial HOM coupler for a superconducting RF cavity and its low-power measurement results

A resonant buildup of beam-induced fields in a superconducting radio frequency (RF) cavity may make a beam unstable or a superconducting RF cavity quench. Higher-order mode (HOM) couplers are used for damping higher-order modes to avoid such a resonant buildup. A coaxial HOM coupler based on the TTF (TESLA Test Facility) HOM coupler has been designed for the superconducting RF cavities at the Proton Engineering Frontier Project (PEFP) in order to overcome notch frequency shift and feed-through tip melting issues. In order to confirm the HOM coupler design and finalize its structural dimensions, two prototype HOM couplers have been fabricated and tested. Low-power testing and measurement of the HOM couplers has shown that the HOM coupler has good filter properties and can fully meet the damping requirements of the PEFP low-beta superconducting RF linac.     

A coaxial HOM coupler for a superconducting RF cavity and its low-power measurement results

A resonant buildup of beam-induced fields in a superconducting radio frequency(RF)cavity may make a beam unstable or a superconducting RF cavity quench. Higher-order mode(HOM)couplers are used for damping higher-order modes to avoid such a resonant buildup. A coaxial HOM coupler based on the TTF (TESLA Test Facility)HOM coupler has been designed for the superconducting RF cavities at the Proton Engineering Frontier Project(PEFP)in order to overcome notch frequency shift and feed-through tip melting issues. In order to confirm the HOM coupler design and finalize its structural dimensions, two prototype HOM couplers have been fabricated and tested. Low-power testing and measurement of the HOM couplers has shown that the HOM coupler has good filter properties and can fully meet the damping requirements of the PEFP low-beta superconducting RF linac.     

北京大学国产大晶粒铌材超导腔的性能研究

大晶粒铌材是射频超导领域的研究热点之一. 采用大晶粒铌材的射频超导谐振腔, 其后处理工艺可以大大简化. 北京大学对此进行了深入细致的研究, 自主研制了采用国产大晶粒铌材的射频超导腔, 对这些超导腔进行了简单的表面处理, 包括标准的化学抛光(BCP)和120℃低温烘烤处理, 未进行非常复杂的电抛光处理, 低温性能测试结果表明其低温超导性能优越, 大晶粒1.3GHz超导腔的加速梯度达到了43.5MV/m, 为我国超导加速器的国产化打下了基础.     

上海光源500MHz超导腔水平测试

上海光源是能量为3.5 GeV的第三代先进中能同步辐射光源,其储存环上安装了三台超导高频腔补偿电子因同步辐射等原因丢失的能量。为保障上海光源的长期稳定高效运行,中国科学院上海应用物理研究所和上海市低温超导高频腔技术重点实验室共同研制了具备低高次模损失参数和可承受更高入射功率的新型500 MHz超导腔,作为上海光源在线运行超导高频腔的备用腔。超导铌腔经低温垂直测试达到所需加速性能后,需要与高功率输入耦合器、高次模吸收器、低温恒温器等集成并完成水平测试,获得超导腔模组的加速性能、低温性能和真空性能。介绍了超导腔备用腔的研制、集成和测试过程,采用文丘里(Venturi)校准法获得模组的静态功耗反应模组的低温性能,并通过高功率测试获得了超导腔备用腔模组的加速性能。测试结果表明:自主研制的500 MHz超导腔备用腔满足上海光源的工作需求,在超导腔的加速腔压为2.0 MV时,无载品质因数为1.2×109 @4.2 K,且低温模组的静态热损耗为36.1 W。     

Stop band characteristics of a TESLA cavity coaxial-type HOM coupler

A TTF-type coaxial higher order modes (HOM) coupler has been used in a TESLA 9 cell cavity. It is impossible to measure the stop band characteristics of the HOM coupler with the cavity. A measurement device for the coaxial transmission line type for the HOM coupler has been designed at Peking University. Experimentally it was shown that the average voltage standing wave ratio of the coaxial transmission line is smaller than 1.08. The experimental results of the stop band characteristics of the TTF-type HOM coupler have been fitted for the simulation. This paper describes the design of the measurement device and discusses the experimental and simulation results of stop band characteristics of the HOM coupler.     

Engineering three-dimensional maximally entangled states for two modes in a bimodal cavity

An alternative scheme is proposed for engineering three-dimensional maximally entangled states for two modes of a superconducting microwave cavity. In this scheme, an appropriately prepared four-level atom is sent through a bimodal cavity. During its passing through the cavity, the atom is coupled resonantly with two cavity modes simultaneously and addressed by a classical microwave pulse tuned to the required transition. Then the atomic states are detected to collapse two modes onto a three-dimensional maximally entangled state. The scheme is different from the previous one in which two nonlocal cavities are used. A comparison between them is also made.     

Investigation of higher spanwise Helmholtz resonance modes in slender covered cavities

Cavity aeroacoustic noise is relevant for aerospace and automotive industries and widely investigated since the 1950s. Most investigations so far consider cavities where opening length and width are of similar scale. The present investigation focuses on a less investigated setup, namely cavities that resemble the door gaps of automobiles. These cavities are both slender (width much greater than length or depth) and partially covered. Furthermore they are under influence of a low Mach number flow with a relatively thick boundary layer. Under certain conditions, these gaps can produce tonal noise. The present investigation attempts to reveal the aeroacoustic mechanism of this tonal noise for higher resonance modes. Experiments have been conducted on a simplified geometry, where unsteady internal pressures have been measured at different spanwise locations. With increasing velocity, several resonance modes occur. In order to obtain higher mode shapes, the cavity acoustic response is simulated and compared with experiment. Using the frequency-filtered simulation pressure field, the higher modes shapes are retrieved. The mode shapes can be interpreted as the slender cavity self-organizing into separate Helmholtz resonators that interact with each other. Based on this, an analytical model is derived that shows good agreement with the simulations and experimental results.     

Great progress in developing 500 MHz single cell superconducting cavity in China

Superconducting cavities have been adopted in many kinds of accelerator facilities such as synchrotron radiation light source, hard X-ray free electron laser linac, colliders and energy recovery linacs (ERL). The 500 MHz superconducting cavities will be a candidate to be installed in the high current accelerators and high current ERLs for their large beam aperture, low higher order modes impedance and high current threshold value. This paper presents great progress in the whole sequence of developing 500 MHz superconducting cavity in China. It describes the first in-house successful development of 500 MHz single cell superconducting cavity including the deep-drawing of niobium half cells, electron beam wielding of cavity, surface preparations and vertical testing. The highest accelerating gradient of the fabricated cavity #SCD-02 higher than 10 MV/m was obtained while the quality factor was better than 4×10⁸ at 4.2 K, which has reached the world level of the same kind of cavities.     

Study on the 1.3 GHz low loss shape superconducting cavities at IHEP

As part of the international research program on the superconducting cavity for the International Linear Collider (ILC) R&;D on the 1.3 GHz low loss superconducting cavities has been carried out at the Institute of High Energy Physics (IHEP) since 2005. A design of 1.3 GHz low loss cavity shape was proposed and six single-cell cavities of different niobium material were successfully fabricated with standard technology. In this study our priority was on large grain (LG) cavities. The two LG cavities were treated with complete procedures of surface treatments based on chemical polishing (CP) without electro polishing (EP) at IHEP. The two LG cavities and a fine grain cavity were sent to KEK for vertical testing. All the three cavities reached accelerating gradients higher than 35 MV/m and the maximum gradient of 40.27 MV/m was achieved in the LG cavity. This paper presents the process of the vertical RF tests and the comparison of the LG and fine grain cavities's performance.     

直线加速器超导段故障补偿的人工智能算法研究

强流直线加速器的长时间稳定运行是该领域的难点和前沿课题之一。以加速器驱动嬗变研究装置(CiADS)的加速器为例,利用TraceWin软件模拟的虚拟加速器数据,提出了基于人工智能算法的超导腔失效的分段故障补偿方法。当有腔体故障时,故障腔的相邻器件将用于重新匹配束流包络,而所有下游腔均可用于补偿束流能量。与传统的优化方法相比,该方法可实现低能耗的超导腔段的故障补偿,具有计算速度快、普适性强等优点,为实际应用器件故障补偿提供了新的可行性。     

Preliminary study of the higher-harmoni ccavity for HLS-Ⅱ

A higher-harmonic cavity will be used to increase the beam lifetime and suppress coupled-bunch instabilities for Hefei Light Source-Ⅱ. In this paper, results simulated by the particle-tracking model confirm that tuning in the harmonic cavity may suppress the parasitic coupled-bunch instabilities. The factors calculated for lifetime improvement are larger than 2.5. The 3rd and 4th harmonic cavities have been designed. In particular, the absorbers and antenna couplers are applied in harmonic cavities to damp the higher order modes. Finally, the 4th harmonic cavity similar to the Duke's RF cavity will be used for HLS-Ⅱ.     

Study on the 1.3 GHz low loss shape superconducting cavities at IHEP

As part of the international research program on the superconducting cavity for the International Linear Collider (ILC) R&D on the 1.3 GHz low loss superconducting cavities has been carried out at the Institute of High Energy Physics (IHEP) since 2005. A design of 1.3 GHz low loss cavity shape was proposed and six single-cell cavities of different niobium material were successfully fabricated with standard technology. In this study our priority was on large grain (LG) cavities. The two LG cavities were treated with complete procedures of surface treatments based on chemical polishing (CP) without electro polishing (EP) at IHEP. The two LG cavities and a fine grain cavity were sent to KEK for vertical testing. All the three cavities reached accelerating gradients higher than 35 MV/m and the maximum gradient of 40.27 MV/m was achieved in the LG cavity. This paper presents the process of the vertical RF tests and the comparison of the LG and fine grain cavities's performance.     

射频超导谐振腔中的电磁场研究

由高纯铌制成的射频超导谐振腔在高场时会出现Q值下降现象，这是高场下超导腔表面局部磁场增强所致. 为研究高场下超导腔表面的电磁场特性，用单cell超导腔设计了腔表面峰值磁场的研究实验. 通过对单cell超导腔表面峰值磁场的测量，可以确定超导腔焊缝及iris附近表面是否存在缺陷，以便进一步进行腔的处理来改进腔的性能.     

LOM and HOM damping study in a superconducting deflecting cavity for ALS at LBNL

Superconducting deflecting cavities can be used in synchrotron light source to generate subpicosecond X-ray pulses while the impedance of the lower order modes (LOM) and higher order modes (HOM) in the cavity should be kept below an accepted level to avoid beam instability. These modes can be damped by adding waveguide on beam pipe. Detailed simulation of Q in CST Microwave Studio is introduced and experiment results on an aluminum model cavity with damping waveguide are reported to make a comparison.     

Lorentz detuning and tuning system study of 3+1/2cell DC-SC photo-injector for PKU-FEL

A 3+1/2cell DC-SC photo-injector for PKU-FEL facility is under development, which is an upgrade design of the successful 1+1/2cell DC-SC photo-injector. The Lorentz detuning and tuning structure for the 3+1/2cell superconducting cavity is presented in this paper. The Lorentz force detuning coefficient is 7.2 Hz/(MV/m)2 with double stiffening rings for the half cell and single stiffening rings between the adjacent TESLA cells. With the special stiffening structure, the 3+1/2cell whole cavity needs only one tuner. The influences of the tuning on frequency shift, field flatness and average gradient are discussed in this paper. The simulation results show that the stiffening rings' design is successful.     

Stop band characteristics of a TESLA cavity coaxial-type HOM coupler

A TTF-type coaxial higher order modes (HOM) coupler has been used in a TESLA 9 cell cavity. It is impossible to measure the stop band characteristics of the HOM coupler with the cavity. A measurement device for the coaxial transmission line type for the HOM coupler has been designed at Peking University. Experimentally it was shown that the average voltage standing wave ratio of the coaxial transmission line is smaller than 1.08. The experimental results of the stop band characteristics of the TTF-type HOM coupler have been fitted for the simulation. This paper describes the design of the measurement device and discusses the experimental and simulation results of stop band characteristics of the HOM coupler.     

Scheme for Preparation of W State Among Three Cavity Modes

We present a scheme of preparing the tripartite W state among three cavity modes of radiation field inside high-Q superconducting cavities. Our scheme is based on the interaction of a four-level atom with the cavity field for precalculated interaction times with every mode.     

Investigation of the Purcell effect in photonic crystal cavities with a 3D Finite Element Maxwell Solver

Photonic crystal cavities facilitate novel applications demanding the efficient emission of incoherent light. This unique property arises when combining a relatively high quality factor of the cavity modes with a tight spatial constriction of the modes. While spontaneous emission is desired in these applications the stimulated emission must be kept low. A measure for the spontaneous emission enhancement is the local density of optical states (LDOS). Due to the complicated three dimensional geometry of photonic crystal cavities the LDOS quantity has to be computed numerically. In this work, we present the computation of the LDOS by means of a 3D Finite Element (FE) Maxwell Solver. The solver applies a sophisticated symmetry handling to reduce the problem size and provides perfectly matched layers to simulate open boundaries. Different photonic crystal cavity designs have been investigated for their spontaneous emission enhancement by means of this FE solver. The simulation results have been compared to photoluminescence characterizations of fabricated cavities. The excellent agreement of simulations and characterizations results confirms the performance and the accuracy of the 3D FE Maxwell Solver.