Capillary scale light emitting diode based multi-reflection absorbance detector

We describe a light emitting diode (LED) based multi-reflection capillary scale absorbance detector based on both square and round capillaries and compare their performance with a conventional single-pass on-tube detector. The optical path length is extended by silver coating, the external surface of the capillary. The reflective geometry has been reported to be less prone to artifacts induced by refractive index changes; we do find this to be true. Although the detection volume/illuminated volume is increased some, a multi-reflection cell based on a 180 μm bore capillary with a ∼2-cm long illuminated volume shows over a 50-fold gain in signal-to-noise (S/N) compared to a single-pass on-tube configuration with the same capillary. The limit of detection (LOD) is 4.4 fmol (2.6 pg, 1 μL of 22.0 nM injected dye) BTB under pulseless (pneumatic) flow conditions. The cells behave as multipath devices where the effective path lengths are greater at low absorbance values. In our experiments, where non-coherent light is launched through optical fibers that are large compared to capillary bore dimensions, increase in the effective path length of the cell do not occur in a predictable fashion with the angle of incidence of the light beam. Although the effective path length almost linearly increases with increasing distance between the light entry and exit windows, the absolute values of the effective path lengths are always lower than this physical distance, suggesting that after some passage through the solution, light largely travels through or along the glass wall. Square capillaries have better light transmission and offer some performance advantages. Multi-reflection cells can indeed be of value for sensitive detection in microflow systems.     

Improvement in the sensitivity of microfluidic ELISA through field amplified stacking of the enzyme reaction product

In this article, we demonstrate a novel approach to enhancing the sensitivity of enzyme-linked immunosorbent assays (ELISA) through pre-concentration of the enzyme reaction product (resorufin/4-methylumbelliferone) in free solution. The reported pre-concentration was accomplished by transporting the resorufin/4-methylumbelliferone molecules produced in the ELISA process towards a high ionic-strength buffer stream in a microfluidic channel while applying a voltage drop across this merging region. A sharp change in the electric field around the junction of the two liquid streams was observed to abruptly slow down the negatively charged resorufin/4-methylumbelliferone species leading to the reported pre-concentration effect based on the field amplified stacking (FAS) technique. It has been shown that the resulting enhancement in the detectability of the enzyme reaction product significantly improves the signal-to-noise ratio in the system thereby reducing the smallest detectable analyte concentration in the ELISA method. Applying the above-described approach, we were able to detect mouse anti-BSA and human TNF-α at concentrations nearly 60-fold smaller than that possible on commercial microwell plates. For the human TNF-α sample, this improvement in assay sensitivity corresponded to a limit of detection (LOD) of 0.102 pg mL⁻¹ using the FAS based microfluidic ELISA method as compared to 7.03 pg mL⁻¹ obtained with the traditional microwell plate based approach. Moreover, because our ELISAs were performed in micrometer sized channels, they required sample volumes about two orders of magnitude smaller than that consumed in the latter case (1 μL versus 100 μL).     

Biosensor immunoassays for the detection of bisphenol A

Bisphenol A (BPA) is a xenoestrogen found in the environment, in consequence, for the biosensor detection of BPA we raised antibodies (polyclonal (PAbs) and monoclonal (MAbs)) against a structural analogue of BPA, 4,4 bis-(4-hydroxyphenyl) valeric acid (BVA). The kinetics of the MAb-BPA interaction were evaluated and the MAb providing the highest affinity was directly immobilized onto the sensor chip surface to evaluate a direct assay. Afterwards, the performance of the MAbs and the PAbs was compared in an inhibition assay using a BVA-coated chip.The highest sensitivity (limit of detection (LOD) of 0.4 μg L⁻¹) was obtained with MAb 12 in the direct assay. However, the inhibition assay was the most robust and the PAbs showed the highest sensitivity (LOD of 0.5-1 μg L⁻¹). The antibodies were specific for BVA and BPA as only minor cross-reactivities were found toward structurally related compounds or other endocrine disruptors. In the inhibition assay (with a run time of 6 min), water samples spiked with BPA at different levels (0.5-50 μg L⁻¹) resulted in recoveries varying between 68% and 121%. The sensitivity of the inhibition assay could be improved 40 times (LOD of 0.03 μg L⁻¹ with the Mab 12-based assay) using solid phase extraction (SPE).     

Very low optical absorptions and analyte concentrations in water measured by Optimized Thermal Lens Spectrometry

Thermal Lens Spectrometry has traditionally been carried out in the single-beam and the mode-mismatched dual-beam configurations. Recently, a much more sensitive dual-beam TL setup was developed, where the probe beam is expanded and collimated. This feature optimizes Thermal Lens (TL) signal and allows the use of thicker samples, further improving the sensitivity. In this paper, we have made comparisons between the conventional and optimized TL configurations, and presented applications such as measurements of very low absorptions and concentrations in water and Cr(III) aqueous solution in the UV-vis range. For pure water we found linear absorption coefficients as low as the Raman scattering one due to the stretching vibrational modes of OH group. The detection limit was estimated 1 × 10⁻⁶ cm⁻¹ with a 180-mW excitation power using a 100-mm cell length. This sensitivity is very high, considering that water has a photothermal enhancement factor ∼33 times smaller than CCl₄, for example. For Cr(III) species in aqueous solution, the limit of detection (LOD) was estimated in ∼40 ng mL⁻¹ at 514 nm, or ∼10 ng mL⁻¹ at 405 nm, which is ∼30 times smaller than the LOD achieved with conventional transmission techniques. The more recent TL configuration is very attractive to obtain absorption spectra, since the result does not depend critically on the beam parameters, unlike the other configurations. The main drawbacks of this optimized TL configuration are the longer acquisition time and the need for larger samples.     

Sulfide determination in hydrothermal seawater samples using a vibrating gold micro-wire electrode in conjunction with stripping chronopotentiometry

A rapid electrochemical stripping chronopotentiometric procedure to determined sulfide in unaltered hydrothermal seawater samples is presented. Sulfide is deposited at −0.25 V (vs Ag/AgCl, KCl 3 M) at a vibrating gold microwire and then stripped through the application of a reductive constant current (typically −2 μA). The hydrodynamic conditions are modulated by vibration allowing a short deposition step, which is shown here to be necessary to minimize H₂S volatilization. The limit of detection (LOD) is 30 nM after a deposition step of 7 s. This LOD is in the same range as the most sensitive cathodic voltammetric technique using a mercury drop electrode and is well below those reported previously for other electrodes capable of being implemented in situ.     

An easily-automated assay for the physiological state quantification of Pseudomonas sp. M18

In order to foreknow poorly performing cultures before wasting energy to scale them to large cultures, industrial microbial fermentation can greatly benefit from knowledge of the physiological state of cells. The method currently proposed is an easily automated physiological state determination method. We have designed one universal rRNA-specific probe for bacteria and developed novel signal probe hybridization (SPH) assay featuring no RNA extraction and no PCR amplification steps necessary to quantify the physiological state of microbial cells. The microbial cell was lysed with sonication and SDS. Signal probes were applied to hybridize and protect the rRNA target. S1 nuclease was then applied to remove the excessive signal probes, the single-stranded RNA and the mismatch RNA/DNA hybrids. The remaining signal probe was captured with a corresponding capture probe immobilized on a microplate and quantified with a horseradish peroxidase-conjugated color reaction. We then systemically optimized our assay. Results showed that the cell limit of detection (LOD) and the cell limit of quantification (LOQ) were 2.64 × 10⁴ cells and 9.86 × 10⁴ cells per well of microplate, respectively. The limit of detection (LOD) and the limit of quantification (LOQ) of signal probe were 49.0 fM and 344.0 fM respectively. Using this technique, we quantified the 16S rRNA levels during the fermentation process of Pseudomonas sp. M18. Our results indicate that the 16S rRNA levels can directly inform us about the physiological state of microbial cells. This technique has great potential for application to the microbial fermentation industry.     

Development of a disposable amperometric immunosensor for the detection of ecstasy and its analogues using screen-printed electrodes

An amperometric immunosensor for the specific and simple detection of 3,4-methylenedioxyamphetamine (MDA) and its analogues, 3,4-methylenedioxymethamphetamine (MDMA) and 3,4-methylenedioxyethylamphetamine (MDEA) in saliva and urine was developed. A direct competitive assay in which free analyte and horseradish peroxidase labelled species were simultaneously added to an immobilised polyclonal antibody was employed. Both MDA and MDMA could be labelled with the enzyme and the use of an MDMA-HRP tracer greatly enhanced the sensitivity of the assay. Amperometric detection was performed at +100 mV versus Ag/AgCl, using tetramethylbenzidine (TMB)/H₂O₂ as substrate. The antibody, raised specifically against the methylenedioxy moiety of an MDA-BSA immunogen allowed highly specific detection of these analogues with negligible cross-reactivity towards any other amphetamine related compounds. Total assay time was 45 min and the standard curve using MDA could be evaluated within the range 0.61-400 ng ml⁻¹ with corresponding limit of detection (LOD) of 0.36 and 0.042 ng ml⁻¹ for saliva and urine, respectively. The cross-reactivity pattern of the analytes was determined and showed the order of sensitivity increased with increased alkyl chain length (MDA < MDMA < MDEA). The overall performance of the sensor, working range, precision and sensitivity demonstrate its usefulness for rapid and direct measurement of methylenedioxy analogues of ecstasy in saliva and urine. The sensor has better specificity than any previous method for ecstasy, with greater sensitivity than ELISA methods, is less expensive/assay with an “easier to use” format than previous methods. The detection works in saliva or urine, eliminating requirement of blood sampling, with improved precision.     

A novel procedure for rapid surface functionalisation and mediator loading of screen-printed carbon electrodes

We report a simple and rapid procedure that leads to incorporation of mediator and introduction of amine functionality onto the surface of screen-printed carbon electrodes (SPCE). The electrodes were doped with cobalt phthalocyanine (CoPc) by enhanced adsorption in a process that uses minimal amounts of this redox mediator as compared with CoPc loaded inks. The CoPc-doped SPCE showed a substantially increased sensitivity to hydrogen peroxide and thiocholine as compared to unmodified electrodes. This greatly facilitated their use as transducers for the construction of amperometric biosensors based on enzymes producing oxidizable products such as hydrogen peroxide or thiols. Immobilisation of enzymes including glucose oxidase, acetylcholinesterase and choline oxidase was achieved through their multi-contact electrostatic interaction with polyethyleneimine (PEI) which was electrodeposited on the surface of CoPc-doped electrodes in one step from ethanolic solution. The efficiency of enzyme immobilisation was shown to depend on the molecular weight of the PEI used, reaching a maximum for 25 kDa PEI. The biosensors shown sensitivity to glucose at 130 nA mM⁻¹ (LOD 0.15 mM) and to acetylcholine at 70 nA mM⁻¹ (LOD 0.10 mM) under +0.6 V. Detection of glucose has been demonstrated at +0.4 V with the sensitivity of 60 nA mM⁻¹ and LOD of 0.33 mM. Possibility of the inhibition analysis of pesticides has been shown for acetylcholinesterase-based sensors.     

Portable flow-injection analyzer with liquid-core waveguide based fluorescence, luminescence, and long path length absorbance detector

We describe a multifunctional flow analysis instrument that is portable ( cm, 2.3 kg) for facile field deployment. Using a 50 cm long Teflon^® AF tubing as final reaction and optical measurement conduit, we combine a liquid-core waveguide (LCW) based fluorescence detector that is transversely illuminated by an addressable light emitting diode array, a chemiluminescence (CL) detector and an absorbance detector with a solid-state broadband (400-700 nm) source. Several illustrative experiments have been carried out to test the performance of the instrument in different detection modes. A S/N=3 limit of detection (LOD) of 0.25 μg l⁻¹ for chromium(VI) was established using the diphenylcarbazide chemistry, and an LOD of 5 μg l⁻¹ was similarly established for Al(III), using Pyrocatechol Violet (PCV) as the chelating chromogenic dye, in both cases using long path absorption detection. The LOD for aqueous hydrogen peroxide was 16 nM using a fluorescence method based on the formation of thiochrome from thiamine and 4 nM by a luminol chemiluminescence method. With a Nafion membrane diffusion scrubber (DS), the LOD was 8.0 pptv for gaseous hydrogen peroxide by the fluorescence method.     

Portable system for near-real time measurement of gaseous formaldehyde by means of parallel scrubber stopped-flow absorptiometry

Formaldehyde, HCHO, is one of the important causal agents of sick-building syndrome. It is also an important product of ambient air photochemistry. We report here a portable instrument capable of a 0.08 ppbv limit of detection (LOD) and a time resolution of 5 min that is useful for both indoor and ambient air applications. The detection is based on efficient gas collection and chromogenic reaction with 3-methyl-2-benzothiazolone hydrazone (MBTH) through a pair of alternately sampling small-bore porous-membrane tube diffusion scrubbers (DS). The chemistry is well established, requires no special reagent preparation or elevated reaction temperatures and permits the use of inexpensive light emitting diode (LED)-based detectors without need for long path cells. Stopped flow alternate sampling allows an HCHO collection performance, an order of magnitude better than any previous system with high throughput and high sensitivity. Results for indoor and ambient air analyses are presented.     

Development of a gel monolithic column polydimethylsiloxane microfluidic device for rapid electrophoresis separation

A β-cyclodextrin (β-CD)-bonded gel monolithic column polydimethylsiloxane (PDMS) microfluidic device was developed in a simple and feasible way. Before preparation of gel monolithic column in PDMS microchannel, PDMS surface was activated by UV light to create silanol groups, which is an active molecule to covalently bond 3-(trimethoxysilyl)-propyl methacrylate (Bind-Silane) and seal microfluidic device. By the way, Bind-Silane is a bifunctional molecule to link polyacrylamide (PAA) gel and inner wall of PDMS microchannel covalently. Allyl-β-CD was used not only as a multifunctional crosslinker in PAA gel to control the size of the pores, but also as a chiral selector for the enantioseparation. The stability, transferring heat and optical characteristic of the microfluidic device were examined. The separation capability of the gel monolithic column was confirmed by the successful separation of fluorescein isothiocyanate (FITC)-labeled arginine (Arg), glutamine acid (Glu), tryptophan (Try), cysteine (Cysteine) and phenylalanine (Phe) in the PDMS microfluidic device less than 100 s at 36 mm effective separation length. A maximum of 2.06 × 10⁵ theoretical plates was obtained by the potential strength of 490 V/cm. A pair of FITC-labeled dansyl-d,l-threonine (Dns-Thr) was separated absolutely.     

On-line wall-free cell for laser-induced fluorescence detection in capillary electrophoresis

A wall-free detection method based on liquid junction in a capillary gap was proposed for laser-induced fluorescence (LIF) of capillary electrophoresis (CE). The capillary gap of the wall-free cell was fabricated by etching a 10-mm × 50-μm I.D. fused-silica capillary to obtain a polyimide coating sleeve, decoating about 6 mm at one end of both 50 μm I.D. separation and liquid junction capillary, inserting the treated capillary ends into the coating sleeve oppositely, fixing the capillaries with a gap distance of 140 μm by epoxy glue and removing the coating sleeve by burning. The theoretical model, experimental results and wall-free cell images indicated that the gap distance and applied voltage were main influence factors on the wall-free detection. Since the wall-free cell increased the absorption light path and avoided the stray light from the capillary wall, it improved the ratio of signal to noise and limit of detection (LOD) of CE-LIF. Three flavin compounds of riboflavin (RF), flavin mononucleotide sodium (FMN) and flavin adenine dinucleotide disodium (FAD) were used to evaluate the wall-free detection method. Compared with on-column cell, the LODs of the wall-free cell were improved 15-, 6- and 9-fold for RF, FMN and FAD, respectively. The linear calibration concentrations of the flavins ranged from 0.005 to 5.0 μmol/L. The column efficiency was in the range from 1.0 × 10⁵ to 2.5 × 10⁵ plates. The wall-free detection of CE-LIF was applied to the analysis of the flavins in spinach and lettuce leaves.     

Microfluidic bead-based multienzyme-nanoparticle amplification for detection of circulating tumor cells in the blood using quantum dots labels

This study reports the development of a microfluidic bead-based nucleic acid sensor for sensitive detection of circulating tumor cells in blood samples using multienzyme-nanoparticle amplification and quantum dot labels. In this method, the microbeads functionalized with the capture probes and modified electron rich proteins were arrayed within a microfluidic channel as sensing elements, and the gold nanoparticles (AuNPs) functionalized with the horseradish peroxidases (HRP) and DNA probes were used as labels. Hence, two signal amplification approaches are integrated for enhancing the detection sensitivity of circulating tumor cells. First, the large surface area of Au nanoparticle carrier allows several binding events of HRP on each nanosphere. Second, enhanced mass transport capability inherent from microfluidics leads to higher capture efficiency of targets because continuous flow within micro-channel delivers fresh analyte solution to the reaction site which maintains a high concentration gradient differential to enhance mass transport. Based on the dual signal amplification strategy, the developed microfluidic bead-based nucleic acid sensor could discriminate as low as 5 fM (signal-to-noise (S/N) 3) of synthesized carcinoembryonic antigen (CEA) gene fragments and showed a 1000-fold increase in detection limit compared to the off-chip test. In addition, using spiked colorectal cancer cell lines (HT29) in the blood as a model system, the detection limit of this chip-based approach was found to be as low as 1 HT29 in 1 mL blood sample. This microfluidic bead-based nucleic acid sensor is a promising platform for disease-related nucleic acid molecules at the lowest level at their earliest incidence.     

A versatile total internal reflection photometric detection cell for flow analysis

A total internal reflection (TIR) flow-through cell that is highly tolerant of schlieren effects, has limited hydrodynamic dispersion and does not trap gas bubbles, and which is suitable for sensitive photometric measurements in flow analysis, is described. Light from an optical fibre is introduced into a short length of quartz capillary through the sidewall at an incident angle of ca. 53°. Under this condition, incident light undergoes total internal reflection from the external air-quartz interface and is propagated by successive reflections from the external walls through the aqueous liquid core of the cell. Detection of the transmitted beam is enabled by intentionally introducing an optical coupling medium at a predetermined distance along the capillary wall, which allows the internally reflected light to be captured by a second optical fibre connected to a charge-couple device detector.This configuration embodies a number of the desirable features of a liquid core waveguide cell (i.e. total internal reflection), a multi-reflection (MR) flow cell (i.e. minimum susceptibility to schlieren effects, low hydrodynamic dispersion and little tendency to trap bubbles), and a conventional Z-cell (wide dynamic range). When employed with a flow injection system, a limit of detection of 2.0 μg PL⁻¹ was achieved for the determination of reactive phosphate using the TIR cell, compared with LOD values of 3.8 μg PL⁻¹ and 4.9 μg PL⁻¹ obtained using the MR and Z-cells with same manifold.The combined advantages of schlieren-tolerance and lack of bubble entrapment of the MR cell with the higher S/N ratio and wider dynamic range of a conventional Z-cell, make the TIR cell eminently useful for photometric measurements of samples with widely differing refractive indices.     

Microfluidic device capable of sensing ultrafast chemiluminescence

Based on the principle of liquid core waveguide, a novel microfluidic device with micro-scale detection window capable of sensing flashlight emitted from rapid 1,1′-oxalyldi-4-methylimidazole (OD4MI) chemiluminescence (CL) reaction was fabricated. Light emitted from OD4MI CL reaction occurring in the micro-dimensional pentagonal detection window (length of each line segment: 900.0 μm, depth: 50.0 μm) of the microfluidic device with two inlets and one outlet was so bright that it was possible to take an image every 1/30 s at the optimal focusing distance (60 cm) using a commercial digital camera. Peaks obtained using a flow injection analysis (FIA) system with the micro-scale detection window and OD4MI CL detection show excellent resolution and reproducibility without any band-broadening observed in analytical devices having additional reaction channel(s) to measure light generated from slow CL reaction. Maximum height (H_max) and area (A) of peak, reproducibility and sensitivity observed in the FIA system with the microfluidic device and OD4MI CL detection depends on (1) the mole ratio between bis(2,4,6-trichlorophenyl) oxalate and 4-methyl imidazole yielding OD4MI, (2) the flow rate to mix OD4MI, H₂O₂ and 1-AP in the detection window of the microfluidic device, and (3) H₂O₂ concentration. We obtained linear calibration curves with wide dynamic ranges using H_max and A. The detection limit of 1-AP determined with H_max and A was as low as 0.05 fmole/injection (signal/background = 3.0).     

A highly sensitive label-free resonance light scattering assay of carcinoembryonic antigen based on immune complexes

As a kind of glycoprotein, carcinoembryonic antigen (CEA) is the important tumor marker for clinical diagnosis of the presence or recurrence of cancer. In this work, a novel label-free resonance light scattering (RLS) spectral CEA assay was developed based on the combination of highly selective immunoreaction and ultrasensitive RLS technique. In Tris–HCl buffer solution (pH 7.5), the specific immunoreaction between CEA antigen and mouse anti-CEA formed immune complexes which had a maximum RLS spectral peak at 389.0 nm, with the existence of physiological saline and polyethylene glycol 20,000 (PEG 20,000). Under the optimal conditions, the magnitude of enhanced RLS intensity (ΔI_RLS) was proportional to the concentration of CEA in the range from 0.1 to 60 ng mL⁻¹, with a detection limit (LOD, 3σ) of 0.03 ng mL⁻¹. The characteristics of RLS, the CEA immunocomplex, the immune response, the ratio of CEA antigen and mouse anti-CEA, and the optimum conditions of the immunoreaction have been investigated. The CEA concentrations of 20 serum specimens detected by the developed assay showed consistent results in comparison with those obtained by commercially available enzyme-linked immunosorbent assay (ELISA) kit. And this method has many satisfying merits including label-free, sensitivity and high selectivity.     

Selective spectrophotometric determination of TNT using a dicyclohexylamine-based colorimetric sensor

Because of the extremely heterogeneous distribution of explosives in contaminated soils, on-site colorimetric methods are efficient tools to assess the nature and extent of contamination. To meet the need for rapid and low-cost chemical sensing of explosive traces or residues in soil and post-blast debris, a colorimetric absorption-based sensor for trinitrotoluene (TNT) determination has been developed. The charge-transfer (CT) reagent (dicyclohexylamine, DCHA) is entrapped in a polyvinylchloride (PVC) polymer matrix plasticised with dioctylphtalate (DOP), and moulded into a transparent sensor membrane sliced into test strips capable of sensing TNT showing an absorption maximum at 530 nm when placed in a 1-mm spectrophotometer cell. The sensor gave a linear absorption response to 5-50 mg L⁻¹ TNT solutions in 30% aqueous acetone with limit of detection (LOD): 3 mg L⁻¹. The sensor is only affected by tetryl, but not by RDX, pentaerythritoltetranitrate (PETN), dinitrotoluene (DNT), and picric acid. The proposed method was statistically validated for TNT assay against high performance liquid chromatography (HPLC) using a standard sample of Comp B. The developed sensor was relatively resistant to air and water, was of low-cost and high specificity, gave a rapid and reproducible response, and was suitable for field use of TNT determination in both dry and humid soil and groundwater with a portable colorimeter.     

Paper-based electrochemical cyto-device for sensitive detection of cancer cells and in situ anticancer drug screening

In this work, using human acute promyelocytic leukemia cells (HL-60) as a model, a novel microfluidic paper-based electrochemical cyto-device (μ-PECD) was fabricated to demonstrate a facile, portable, and disposable approach for cancer cell detection and in situ screening of anticancer drugs in a high-throughput manner. In this μ-PECD, aptamers modified three-dimensional macroporous Au-paper electrode (Au-PE) was fabricated and employed as the working electrode for specific and efficient cancer cell capture as well as for sequential in-electrode 3D cell culture. This Au-PE showed enhanced capture capacity for cancer cells and good biocompatibility for preserving the activity of captured living cells. Sensitive cancer cell detection was achieved in this μ-PECD, which could respond down to four HL-60 cells in 10 μL volume with a wide linear calibration range from 5.0 × 10² to 7.5 × 10⁷ cells mL⁻¹ and exhibited good stability and reproducibility. Then, in situ anticancer drug screening was successfully implemented in this μ-PECD through monitoring of the apoptotic cancer cells after the in-electrode 3D cell culture with drug-containing culture medium, demonstrating its wide range of potential applications to facilitate effective clinical cancer diagnosis and treatment.     

Improved porous silicon microarray based prostate specific antigen immunoassay by optimized surface density of the capture antibody

Enriching the surface density of immobilized capture antibodies enhances the detection signal of antibody sandwich microarrays. In this study, we improved the detection sensitivity of our previously developed P-Si (porous silicon) antibody microarray by optimizing concentrations of the capturing antibody. We investigated immunoassays using a P-Si microarray at three different capture antibody (PSA – prostate specific antigen) concentrations, analyzing the influence of the antibody density on the assay detection sensitivity. The LOD (limit of detection) for PSA was 2.5 ng mL⁻¹, 80 pg mL⁻¹, and 800 fg mL⁻¹ when arraying the PSA antibody, H117 at the concentration 15 μg mL⁻¹, 35 μg mL⁻¹, and 154 μg mL⁻¹, respectively. We further investigated PSA spiked into human female serum in the range of 800 fg mL⁻¹ to 500 ng mL⁻¹. The microarray showed a LOD of 800 fg mL⁻¹ and a dynamic range of 800 fg mL⁻¹ to 80 ng mL⁻¹ in serum spiked samples.     

Droplet-based microfluidic lab-on-a-chip for glucose detection

A microfluidic lab-on-a-chip (LoC) platform for in vitro measurement of glucose for clinical diagnostic applications is presented in this paper. The LoC uses a discrete droplet format in contrast to conventional continuous flow microfluidic systems. The droplets act as solution-phase reaction chambers and are manipulated using the electrowetting effect. Glucose is measured using a colorimetric enzyme-kinetic method based on Trinder’s reaction. The color change is detected using an absorbance measurement system consisting of a light emitting diode and a photodiode. The linear range of the assay is 9-100 mg/dl using a sample dilution factor of 2 and 15-300 mg/dl using a sample dilution factor of 3. The results obtained on the electrowetting system compare favorably with conventional measurements done on a spectrophotometer, indicating that there is no change in enzyme activity under electrowetting conditions.