Chemical conditions inside occluded regions on corroding aircraft aluminum alloys

Corrosion of aluminum alloy structures costs the US Air Force in the order of US$1×10⁹ annually. Corrosion develops in areas of overlap such as aircraft lap-splice joints and under protective organic coatings. Capillary electrophoresis (CE) has been used to determine the local chemistries at these corrosion sites of solutions that were extracted using a microsampling system. Analysis of the local solution within lap-splice joints from aircraft has been performed in two ways: rehydration of corrosion products and direct microsampling. The solutions collected were analyzed with CE to quantitatively determine the species present during corrosion. The most common ions detected were Cl⁻, NO₂⁻, NO₃⁻, HCO₃⁻, K⁺, Al³⁺, Ca²⁺, Na⁺ and Mg²⁺. Studies of the solution chemistry under local coating defects are required to understand coating failure and develop more durable coatings. A microsampling system and micro pH sensor were developed to extract solution from and measure pH in defects with diameters as small as 170 μm. Actively corroding defects contained high concentrations of Cl⁻, Al³⁺, Mg²⁺, Mn²⁺ and Cu²⁺ whereas only trace levels of Mg²⁺ were found in repassivated defects. The effects of these species on initiation and propagation of corrosion are discussed.     

Simultaneous separation of inorganic anions and cations by capillary zone electrophoresis

A new capillary electrophoretic approach for simultaneous separation of fast anions and cations is demonstrated. Indirect UV detection at 214 nm in conjunction with electromigration sampling from both ends of the capillary was developed. Two electrolyte systems based on imidazole-nitrate and copper(II)-ethylenediamine-nitrate were investigated for the simultaneous separation of chloride, sulphate, hydrocarbonate, potassium, ammonium, calcium, sodium and magnesium ions. Experimental parameters that were evaluated included a nature of UV chromophore, pH of electrolyte, a nature of complexing agent. The method permits the excellent separation of three anions and five cations in only 4 min using electrolyte system containing 2.5 mmol l⁻¹ Cu(NO₃)₂, 5 mmol l⁻¹ ethylenediamine and 1 mmol l⁻¹ fumaric acid at pH 8.5 adjusted with tetraethylammonium hydroxide.     

Quantitative determination of inorganic minor cations in sodium-, calcium-, magnesium-matrix simulated samples by capillary electrophoresis

The analysis of ammonium, alkali and alkaline-earth trace cations (0.5 ppm) in samples with a calcium, sodium or magnesium matrix (500 ppm) has been achieved using 10 mM imidazole (pH 4.5) electrolyte to which a complexing agent (15-crown-5, oxalic acid or dipicolinic acid) has been specifically added in order to decrease the electrophoretic mobility of the matrix cation and thus to allow the separation of higher mobility cations at sub-ppm concentrations. The influence of several experimental parameters (complexing agent concentration, buffer pH and temperature) have been studied in order to optimize the separation. The complexing agent concentration appears to be the main parameter governing the selectivity of the cations during the analysis of matrix samples. In optimized conditions, we have checked that the separation between minor inorganic cations is not significantly altered by an increase in the matrix cation concentration. As the concentration of the matrix cation increases, the migration times of minor cations remain unchanged even for a 1000 ppm concentration of the matrix cation. Finally, these optimized buffers allow the quantitation of minor cations down to 0.05% (w/w) for calcium- or magnesium- matrix simulated samples and 0.2% (w/w) for sodium-matrix simulated samples.     

Comparison of ion chromatography and capillary electrophoresis for the determination of inorganic ions

The techniques of ion chromatography and capillary electrophoresis are compared as analytical methods for the determination of inorganic anions and cations. Comparison is made in the areas of stage of development, separation efficiency, separation selectivity, analytical performance parameters, method development procedures, applications, strenghts and weaknesses, and future directions. It is shown that the two techniques are complementary rather than competitive, especially with regard to their separation selectivities and the type of applications to which they are most suited.     

Development of a fast capillary electrophoresis method to determine inorganic cations in biodiesel samples

The aim of this study was to develop a fast capillary electrophoresis method for the determination of inorganic cations (Na⁺, K⁺, Ca²⁺, Mg²⁺) in biodiesel samples, using barium (Ba²⁺) as the internal standard. The running electrolyte was optimized through effective mobility curves in order to select the co-ion and Peakmaster software was used to determine electromigration dispersion and buffer capacity. The optimum background electrolyte was composed of 10 mmol L⁻¹ imidazole and 40 mmol L⁻¹ of acetic acid. Separation was conducted in a fused-silica capillary (32 cm total length and 23.5 cm effective length, 50 μm I.D.), with indirect UV detection at 214 nm. The migration time was only 36 s. In order to obtain the optimized conditions for extraction, a fractional factorial experimental design was used. The variables investigated were biodiesel mass, pH, extractant volume, agitation and sonication time. The optimum conditions were: biodiesel mass of 200 mg, extractant volume of 200 μL and agitation of 20 min. The method is characterized by good linearity in the concentration range of 0.5-20 mg kg⁻¹ (r > 0.999), limit of detection was equal to 0.3 mg kg⁻¹, inter-day precision was equal to 1.88% and recovery in the range of 88.0-120%. The developed method was successfully applied to the determination of cations in biodiesel samples.     

毛细管区带电泳法间接测定红细胞中的主要无机阳离子

建立了间接测定红细胞中主要无机阳离子的毛细管区带电泳方法, 考察了背景溶液pH、咪唑和酒石酸浓度等对无机离子分离效果及峰面积的影响. 以10 mmol/L咪唑-4 mmol/L酒石酸(pH 5.5)为背景, 在15 kV、214 nm的条件下, 对红细胞中K 、Mg2 、Ca2 和Zn2 进行了定性、定量分析, 回收率在96%～104%之间, 迁移时间和峰面积的相对标准偏差分别低于0.76%和2.8%(日内), 0.85%和3.7%(日间). 所建方法有望成为一种测定细胞内离子含量的辅助方法.     

Parametric study of a fiber-optic laser-induced breakdown spectroscopy probe for analysis of aluminum alloys

In the present work we demonstrate a fiber-optic laser-induced breakdown spectroscopy (FO LIBS) system for delivering laser energy to a sample surface to produce a spark as well as to collect the resulting radiation from the laser-induced spark. In order to improve the signal/background (S/B) ratio, various experimental parameters, such as laser energy, gate delay and width, detector gain, lenses of different focal lengths and sample surface, were tested. In order to provide high reliability and repeatability in the analysis, we also measured plasma parameters, such as electron density and plasma temperature, and determined their influence on the measurement results. The performance of FO LIBS was also compared with that of a LIBS system that does not use a fiber to transmit the laser beam. LIBS spectra with a good S/B were recorded at 2-μs gate delay and width. LIBS spectra of six different Al alloy samples were recorded to obtain calibration data. We were able to obtain linear calibration data for numerous elements (Cr, Zn, Fe, Ni, Mn, Mg and Cu). A linear calibration curve for LIBS intensity ratio vs. concentration ratio reduces the effect of physical variables (i.e. shot-to-shot power fluctuation, sample-to-surface distance, and physical properties of the samples). Our results reveal that this system may be useful in designing a high-temperature LIBS probe for measuring the elemental composition of Al melt.     

氢化物发生-原子荧光光谱法测定铝合金中痕量砷

建立了测定铝合金中痕量砷HG-AFS分析方法.采用王水溶解样品,在硫脲和抗坏血酸的存在下将As(Ⅴ)还原为As(Ⅲ),以KBH4溶液(20g/L)作为还原剂,HCl(5+95)溶液作为载流,用原子荧光光谱法测定样品中痕量砷.在选定的实验务件下,方法的线性范围为0.05～40μg/L,线性回归方程为,If=108.17+272.49ρ(μg/L),相关系数r=0.9997,检出限0.019μg/L.并与ICP-AES法进行了对照试验.     

Fundamental aspects of contactless conductivity detection for capillary electrophoresis. Part I: Frequency behavior and cell geometry

A better understanding of the characteristics of the axial contactless conductivity cell could be obtained by carefully studying the effect of the cell geometry on its frequency behavior. A good fit between theoretical and experimental results shows that the axial contactless conductometric detector can effectively be described by the simplest possible equivalent circuitry consisting of a capacitor, resistor, and a second capacitor. The cell constant is largely defined by the length of the gap between the electrodes. The effective electrode size is thus not related to the dimensions of the real electrodes but more closely to the cross-sectional area of the internal diameter of the capillary. Typical experimental values of 20 MOmega and 0.1 pF were obtained for the resistance and capacitances, respectively, of a cell formed by a 2 mm gap between two 4 mm long electrodes fitted with a capillary of 50 microm ID. It could be shown that the diameter of the electrode is not critical and tight coupling of the electrodes to the outer wall of the capillary is not needed. The peak overshoot phenomenon, which has frequently been reported, is an artefact that can be minimized by optimizing the frequency for cell excitation. The frequency setting has to be optimized for each cell design, operational amplifier, electrolyte solution and capillary.     

Determination of ammonium,calcium, magnesium,potassium and sodium in drinking waters by capillary zone electrophoresis on a column-coupling chip

This work deals with simultaneous determination of ammonium, calcium, magnesium, sodium and potassium in drinking waters by capillary zone electrophoresis (CZE) on a column-coupling (CC) chip with suppressed hydrodynamic and electroosmotic transports. CZE separations were carried out in a propionate background electrolyte at a low pH (3.2) containing 18-crown-6-ether (18-crown-6) to reach a complete resolution of the cations. In addition, triethylenetetramine (TETA) coated the inner wall surface of the chip channels. The concentration limits of detection (cLOD) for the studied cations ranged from 4.9 to 11.5 μg/l concentrations using a 900 nl volume of the sample injection channel. 93–106% recoveries of the cations in drinking waters indicate a good predisposition of the present method to provide accurate analytical results.     

Separation and determination of inorganic cations in beverages by capillary electrophoresis with indirect UV detection

A rapid, simple and reliable capillary electrophoresis method for the separation and quantitation of inorganic cations with indirect UV detection at 214 nm was developed. The electrolyte was: 12 mM imidazole as background absorbance provider; 5 mM malic acid and 1.0 mM 18-crown-6 ether as complexing agents; and 20% D₂O (v/v) to improve ion mobility. The pH was 4.25. The applied voltage was 22 kV at 22°C. Nine ions were completely separated and determined with correlation coefficients of 0.9979-0.9992. The relative standard deviations (RSD) were less than 0.5% for migration time and less than 5.2% for peak area (n=8). The detection limits (S/N=3) were from 0.08 mg L⁻¹ (for Na⁺) to 0.51 mg L⁻¹ (for Cu²⁺). To assess the reliability atomic absorption (AA) was also used to determine the same samples. Satisfactory results were obtained for real samples of jasmine tea drink and coconut milk.      

Separation of inorganic anions in acidic solution by capillary electrophoresis

Inorganic anions are almost always determined by capillary electrophoresis (CE) at an alkaline pH, so the analytes will be fully ionized. However, a long-chain quaternary ammonium salt usually must be added as a flow modifier to the carrier electrolyte to reverse the direction of the electroosmotic flow. By working at a sufficiently acidic pH, the electroosmotic flow in fused-silica capillaries is virtually eliminated, and anions can be separated simply by differences in their electrophoretic mobilities. Excellent separations were obtained for AuCl₄⁻ and the chloro complexes of platinum group elements in HCl solution at pH 2.0 to 2.4. No additional buffer or flow modifier was needed. This CE technique is an excellent way to follow slow hydrolytic reactions in which one or more of the chloride ligands is replaced by water. Sharp peaks and good separations were also obtained for MnO₄⁻, VO₃⁻, chromate, molybdate, ferrocyanide, ferricyanide and stable complex ions such as chromium oxalate (CrO₃³⁻).     

Application of an external contactless conductivity detector for the analysis of beverages by microchip capillary electrophoresis

Quantitative total ionic analysis of alcoholic and nonalcoholic beverages was performed by microchip capillary electrophoresis with external contactless conductivity detection. An electrolyte solution consisting of 10.5 mM histidine, 50 mM acetic acid, and 2 mM 18-crown-6 at pH 4.1 was used for the determination of NH(4) (+), K(+), Ca(2+), Na(+), and Mg(2+). Fast analysis of Cl(-), NO(3) (-), and SO(4) (2-) was achieved in 20 mM 2-(N-morpholino)ethanesulfonic acid /histidine electrolyte solution at pH 6.0 and the simultaneous separation of up to 12 inorganic and organic anions was performed in a solution containing 10 mM His and 7 mM glutamic acid at pH 5.75. Limits of detection ranged from 90 to 250 mug/L for inorganic cations and anions, and from 200 to 2000 mug/L for organic anions and phosphate. Calibration curves showed linear dependencies over one to two orders of magnitude when the stacking effect was minimized by injecting standard solutions prepared in background electrolyte solutions. Total analysis times of 35 and 90 s were achieved for the determination of 5 inorganic cations and for the simultaneous determination of 12 inorganic and organic anions, respectively, which represents a considerable reduction of analysis time compared to conventional separation methods used in food analysis.     

A new electrolytic dissolution of aluminum alloys and determination of some constituents by inductively coupled plasma optical emission spectrometry

The new electrolytic dissolution in batch of aluminum alloys samples as grains or turns and the determination of Fe, Cu, Mn, Mg, Cr, Ni, Zn, Pb and Ti by ICP OES was investigated. In on-line electrodissolution procedures described in the literature, samples were restricted to be in the form of solid blocks or plates with one polished flat face. Here, the sample was loaded in the barrel of a modified disposable syringe (the anodic semi-cell) and pressed with a modified plunger fitted with a platinum disk to establish electrical contact with the analyte. This arrangement was introduced in a beaker containing the electrolyte (1 mol L⁻¹ HNO₃) and a platinum wire as the cathode. The resulting solution from electrodissolution (0.6 A) was used for the ICP OES determinations. The influence of the aluminum concentration increase on the determination of the elements was evaluated. Electrodissolution of certified reference materials and commercial samples revealed relative errors lower than 10% for the elements Fe, Cu, Mg, Ni, Cr, Zn and Ti (when their content is above 0.1%). Higher inaccuracies (>10%) were observed for Mn and for Fe in B.C.S. 268/1 reference material certified. The proposed method presented a relative standard deviations (R.S.D.) lower or circa 10% to all of the elements (except Pb). In comparison with traditional acid dissolution, the proposed electrodissolution method is relatively fast (about 30 min), it is clean (there is no projection of solution) and simple (heating and fumes exhaust system were not necessaries).     

Optimization of conductivity detection of low-molecular-mass anions in capillary zone electrophoresis

The optimization of background electrolyte compositions for capillary zone electrophoresis in combination with conductivity detection focusing on maximal detector response is discussed. A theoretical approach pointing out the influence of the electrolyte co- and counter-ion mobilities on the detector signal has been developed. Using this model, running buffer compositions providing optimum S/N ratios for the selected analytes could be calculated. The results derived from these examinations have been verified by experimental investigations, namely the determination of inorganic and organic anionic solutes.     

Rapid capillary zone electrophoresis method for the determination of metal cations in beverages

A rapid and reliable capillary zone electrophoresis method for the determination of inorganic cations was developed. The complete separation of K⁺, Ba²⁺, Ca²⁺, Na⁺, Mg²⁺, Mn²⁺, Ni²⁺, Cd²⁺, Li⁺ and Cu²⁺ can be achieved in 4 min with a simple electrolyte composed by 10 mM imidazole as the carrier buffer and background absorbance provider and acetic acid as the complexing agent (pH 3.60). Injection was performed hydrostatically by elevating the sample at 10 cm for 30 s. The running voltage was +25 kV at room temperature. Indirect UV-absorption detection was achieved at 185 nm. The detection limit was in the range between 0.06 mg/l (Mg²⁺) and 0.57 mg/l (K⁺) and the quantification limits ranged from 0.10 mg/l (Ni²⁺) to 0.80 mg/l (Cu²⁺). The calibration graphs were linear in the concentration range from the quantification limit till at least 1 g/l in K⁺, 10 mg/l in Ba²⁺, Ca²⁺, Mg²⁺, Mn²⁺, Ni²⁺ and Cd²⁺, 40 mg/l in Na⁺ and 12 mg/l in Li⁺ and Cu²⁺. The repeatability, intraday and interday analysis were ≤1.55% and ≤3.64% for migration time and ≤3.38% and ≤3.63% for peak area. The method developed has been applied to several beverage samples with only a simple dilution and filtration treatment of the sample. The proposed method is simple, fast, cheap and it is achieved with common products in either laboratory. For these reasons, it is a very useful method for routine analysis.     

Fundamental aspects of contactless conductivity detection for capillary electrophoresis. Part II: Signal-to-noise ratio and stray capacitance

The signal-to-noise ratio of a contactless conductivity detector for capillary electrophoresis was examined for different cell arrangements and operating parameters. The best signal-to-noise ratios, and hence the best detection limits, are obtained for frequencies which give highest sensitivity. Comparative experiments for three different excitation voltages (20, 100, and 200 V(pp)) showed that the best signal-to-noise ratios were achieved for the highest excitation voltage of 200 V(pp). Low conductivity of the background electrolyte solution is mandatory to obtain lowest noise levels, and also the improvement on applying high excitation voltages was best for the electrolyte solution with lowest conductivity. The diameter of the electrodes was found to have only a negligible effect, so that a tight fitting of the electrodes to the external diameter of the capillary is not necessary. A cell without shielding between the two electrodes showed significant direct coupling (stray capacitance) and lower signal-to-noise ratios for all experimental conditions used. A serious distortion of the peak shapes was also observed for this cell arrangement.     

Antihypertensive drugs as an inhibitors for corrosion of aluminum and aluminum silicon alloys in aqueous solutions

The corrosion behavior of aluminum and three aluminum–silicon alloys in different concentrations of HCl solutions and its inhibition by antihypertensive drugs was studied using potentiostatic polarization measurements. As the acid concentration increases, the rate of corrosion increases. Aluminum is less susceptible to corrosion than any of Al–Si alloys. The inhibition efficiency of the drug compounds increases with their concentration up to a critical value. At higher additive concentrations the inhibition efficiency starts to decrease. The inhibitive action of these compounds is due to their formation of insoluble complex adsorbed on the metal surface. The adsorption follows Langmuir adsorption isotherms. It was found that the drugs compounds provide protection to Al and Al–Si alloys against pitting corrosion by shifting the pitting potential to more positive direction until critical drug concentrations (250 ppm). After this critical concentration the inhibition against to pitting corrosion starts to decrease.     

Metal cations for the determination of fluorescent phosphoinositides by capillary electrophoresis

Phosphatidylinositol (PI) and its phosphorylated derivatives known as phosphoinositides (PIPs), are essential regulators of cell signaling and membrane trafficking, cytoskeletal dynamics, and nuclear functions. Disruption of PI metabolism is associated with disorders such as immune dysfunction, cardiovascular disease, and cancer; therefore, there is currently great interest in studying PIPs and their metabolic enzymes. Here, we describe a method for the separation of fluorescent PI and its seven fluorescent phosphorylated derivatives by CE‐LIF. The CE method utilizes a Tris buffer and sodium deoxycholate in the presence of 30% 1‐propanol and 5% of a dynamic coating reagent, EOTrol^TM low reverse (EOTrol LR). It is simple, fast, highly sensitive, and it offers LODs in the order of 1.5 amol. The effect of cations such as lithium, sodium, potassium, cesium, barium, manganese, zinc, magnesium, calcium, spermine, and gentamicin were evaluated. Calcium and magnesium provided the best selectivity and resolution for the separation of the analytes while magnesium offered the best data reproducibility. The developed CE method would be useful in the studies of enzymatic activity in the PI and PIPs metabolic pathways using CE‐based in vitro and CE cell‐based assays, and/or for drug screening.     

Determination of anions in rainwater by capillary electrophoresis with conductivity detection

A routine method for the determination of chloride, nitrate and sulfate anions in rainwater by capillary electrophoresis was developed. The system uses an end-column non-suppressed conductivity detector. Linear calibration plots were generated from 0.050 to 20 mg/l, which is the range generally found in wet depositions. Accuracy and precision were evaluated by analyzing certified standards of simulated rainwater and environmental samples, or by comparing CE results with those obtained by IC, the reference technique for anion analysis in wet deposition. The reproducibility of the method was satisfactory except at the lower and upper limits of the analytical range. Sensitivity lay in the range of few μg/l.