电感耦合等离子体原子发射光谱法测定高温合金中低含量钇

建立电感耦合等离子体原子发射光谱法测定高温合金中低含量钇的方法。采用盐酸、硝酸、氢氟酸溶解样品,在优化的仪器条件下,采用基体匹配法配制系列标准工作溶液,选择分析线为360.073 nm。钇的含量在0.0005%~0.050%范围内与光谱强度具有良好的线性关系,相关系数为0.99999,检出限为0.000003%。该方法测定结果的相对标准偏差不大于6.0%(n=8),加标回收率为90.0%~104.0%。该方法简便、快速、准确,可用于高温合金中低含量钇的测定。     

Determination of boron in boron-alloyed steels by inductively coupled plasma atomic emission spectrometry

An inductively coupled plasma atomic emission spectrometry (ICP-AES) procedure has been developed and examined for the determination of boron content (0.01 up to about 2% B) in boron-alloyed steels such as POLDI ATA BOR (65% Fe, 19%Cr, 12% Ni, 1.5% Mn, 1% B), POLDI ATA BOR EXTRA (62% Fe, 18% Cr, 13% Ni, 2.5% Mo, 1.5% Mn, 1% B) and POLDI ATA BOR-R (75% Fe, 18% Cr, 3.5% Ti, 1.8% B). The steel sample is dissolved with a mixture of hydrochloric, nitric, sulfuric and phosphoric acids in a quartz vessel. Borides of alloyed metals, especially of iron and chromium, are quantitatively decomposed. The presence of phosphoric acid in a sample solution reduces the volatility of boric acid with water vapour.Presented in part at the 1989 European Winter Conference on Plasma Spectrochemistry, Reutte, Austria     

电感耦合等离子体发射光谱法测定高纯铝中硅

建立电感耦合等离子体发射光谱(ICP-AES)法测定高纯铝中硅元素的分析方法。样品采用碱溶法进行预处理,以氢氧化钠溶液溶解,再加入盐酸、硝酸酸化。选取了硅251.611 nm分析谱线进行分析。硅的质量分数在0.001%~0.01%范围内与光谱强度具有良好的线性关系,线性相关系数为0.9991。该方法检出限为0.00012%,测定结果的相对标准偏差不大于10.2%(n=8),加标回收率为93.2%~104.2%。该方法操作简便,测定结果准确、可靠,适用于快速检测高纯铝中硅元素,具有推广价值。     

电感耦合等离子体发射光谱法测定二硼化锆中26种杂质

建立微波消解样品,电感耦合等离子体发射光谱法测定二硼化锆中26种杂质元素含量的方法。根据二硼化锆的化学组成对杂质检测的影响,确定了各元素最佳分析线;通过考察不同浓度的锆基体对待测元素的影响来确定最佳锆基体浓度;通过萃取法分离硼元素,消除硼对杂质检测的干扰;采用基体匹配法、多谱拟和技术消除了锆基体的干扰。在选定的仪器工作条件下,各待测元素的质量浓度与信号强度成良好的线性关系,线性相关系数均大于0.999。测定结果的相对标准偏差不大于6%(n=11),样品加标回收率为94%~101%。该方法操作简便,测定结果准确,可用于二硼化锆中26种杂质元素的测定。     

锌精矿中铟的测定

应用电感耦合等离子体发射光谱法测定锌精矿中的铟,确定了最佳工作条件,选择了最佳分析谱线,并利用标准加入法和基体匹配法确定了该方法的准确性。样品用氟化氢铵、盐酸、硝酸、高氯酸溶样,用盐酸浸取。本法与萃取分离盐酸羟胺示波极谱法测定的铟含量结果一致。方法准确,快速,加标回收率为99.6%~101.7%,相对标准偏差为0.97%~2.1%。     

电感耦合等离子体原子发射光谱法测定钛合金中锆

建立电感耦合等离子体原子发射光谱法(ICP-AES)测定钛合金中锆元素的含量。采用盐酸-氢氟酸-硝酸溶解钛合金样品,选择357.247 nm为锆的分析谱线,通过基体匹配法消除基体钛的干扰,以电感耦合等离子体原子发射光谱法测定钛合金中锆的含量。锆的质量分数在0%~0.4%范围内与光谱强度呈良好的线性关系,相关系数大于0.999,定量下限为0.21%。测定结果的相对标准偏差小于2%(n=11),样品加标回收率为99.0%~102.7%。该方法快速、准确,能够满足实际生产中钛合金样品的测定要求。     

Multielemental trace analysis of biological materials using double focusing inductively coupled plasma mass spectrometry detection

The analytical potential of double focusing-inductively coupled plasma-mass spectrometry (DF-ICP-MS) for total elemental analysis in clinical samples (serum, blood, urine and other biological fluids), tissues and food products is illustrated by reviewing typical applications recently published. Also, the use of DF-ICP-MS as specific detector for trace element speciation in biological samples is discussed. After adequate separation of interferences in the chromatographic column, low resolution measurements (R = 300) can be used to provide enhanced sensitivities of more than 100 times compared with quadrupole-inductively coupled plasma-mass spectrometry (Q-ICP-MS). This capability is extremely valuable in speciation studies. Also, the use of DF-ICP-MS at low resolution could provide very precise isotope ratio measurements for isotope dilution analysis due to the ‘flat topped’ peaks obtained at this resolution. Unfortunately, the literature on these last two issues is rather scarce so far, in spite of their extremely high analytical possibilities for biological research. Moreover, the bright future of DF-ICP-MS as a most powerful multielemental detector for trace element applications in biological systems will be highlighted. Apart from applications detailed above other important application fields can be envisaged. In particular, we will speculate on its possible use to confirm/establish ‘reference values’ of trace element content in ‘normal’ populations and so to help to diagnose health and disease status, related with trace element total content or their speciation in clinical specimens.     

Chemical analysis by inductively coupled plasma atomic emission spectrometry of semiconducting ceramics of barium titanate doped with various metal oxides

The Ba and Ti macroconstituents as well as the impurities and dopants content (Al, Ca, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Na, Nb, Ni, P, Pb, Si, Sr, W, Zn and Zr) in a dense (> 98% theoretical) barium titanate sample have been determined by inductively coupled plasma-atomic emission spectrometry after one of these decomposition routes: (a) decomposition with HCl in a PTFE-lined pressure vessel, (b) fusion with Na₂CO₃ in a platinum crucible, and (c) fusion with Li₂B₄O₇ in a graphite crucible. Matrix effects were taken into account. Detection limits for minors and trace elements were determined. High sensitivity and good precision were attained.Presented in part at the 1989 European Winter Conference on Plasma Spectrochemistry, Reutte, Austria     

Laser ablation inductively coupled plasma atomic emission spectrometry of a uranium-zirconium alloy: ablation properties and analytical behavior

The ablation properties and analytical behavior of a uranium-zirconium alloy have been examined using tandem laser ablation/pneumatic nebulization sample introduction in conjunction with inductively coupled atomic emission spectrometry (LA-ICP-AES). An apparent change in composition of the laser ablation aerosol (1–15 GW cm⁻² Zr deficient, 40–250 GW cm⁻² Zr rich) is observed. This phenomenon is independent of laser wavelength. After collection and bulk chemical analysis of the ablation product, this phenomenon is attributed to an atomization interference in the ICP.

Two distinct modes of laser ablation have been observed which depend upon the wavelength of the ablating laser (visible or near infrared). These two modes result in characteristic ablation crater types and analyte emission behavior. Ablation yields at 1064 nm are dependent upon laser power density only, whilst yields at 532 nm are dependent upon both laser power density and illumination area. The latter is considered to be symptomatic of direct interaction of the laser light with the surface, and the former, of indirect coupling of laser energy, via a micro-plasma, into the surface.     

电感耦合等离子体原子发射光谱法测定稀土钢中微量镧、铈

采用稀王水溶解样品,选择La408.672 nm、Ce456.236nm为分析线,建立了电感耦合等离子体原子发射光谱法(ICP-OES)测定稀土钢中微量镧、铈的方法。结果表明,各元素校准曲线线性良好,相关系数可达0.99999;方法测定范围为：0.0001%～0.10%。检出限为：镧0.00002%,铈0.00006%。按照实验方法测定标样中镧、铈,结果的相对标准偏差RSD(n=8)为2.18%、1.68%。     

电感耦合等离子体原子发射光谱(ICP-OES)法测定硫磺中的铅、铜、铁、镍、钙

提出了电感耦合等离子体原子原子发射光谱测定硫磺中的铅、铜、铁、镍、钙含量的方法,选择各元素的分析谱线,采用正交试验的方法确定仪器的工作参数,方法的检出限0.0046 ug/ml-0.012 ug/ml,方法的回收率在87.60%~111.78%,测定值的相对标准偏差(n=5)小于9.82%,填补无硫磺中铅、铜、镍、钙元素检测方法的空白。     

Determination of tin in soil by continuous hydride generation and inductively coupled plasma mass spectrometry

A method was investigated for the determination of Sn in soil samples by KOH fusion followed by continuous hydride generation coupled with inductively coupled plasma mass spectrometry (HG-ICP-MS). Sample solutions in 3.0 M HCl were mixed in line with a solution of 2.4% NaBH₄ and 0.25 M KOH to generate stannane gas. The mixture was delivered continuously to a gas/liquid separator and the stannane gas was introduced into a Perkin-Elmer Sciex Elan 6000 ICP-MS for concentration measurements. A method detection limit of 0.45 mg/kg was sufficient for Sn levels commonly found in soil samples. Sn concentrations as low as 2.5 mg/kg were reproducibly measured in soil samples. Sample results by HG-ICP-MS agreed within ±17% relative difference to results by instrumental neutron activation analysis (INAA) and within ±6% relative difference to results by KOH fusion followed by inductively coupled plasma optical emission spectroscopy (ICP-OES).     

碰撞池-电感耦合等离子体质谱法测定芝麻中痕量的锗

建立了碰撞池-电感耦合等离子体质谱法测定芝麻中痕量的锗元素(germanium , Ge)。采用微波消解,碰撞池(KED模式)-电感耦合等离子体质谱检测,在线引入内标元素铑(Rh),同时消解液中加入3%正戊醇增敏。结果 3 % 正戊醇可使_⁷⁴Ge的上机检测信号强度提高2.85倍,_⁷⁴Ge校正曲线线性相关系数为1.00000,检出限为0.0555 μg/kg,加标回收率为92.0%~106%,相对标准偏差(relative standard deviation, RSD%)为2.6%~4.3%。采用建立的方法测定7种国家标准物质,检测结果均在认定值范围内,RSD%为2.5%~8.8%。结论 该方法灵敏度高、准确,可实现批量检测,适用于芝麻中痕量锗的检测。     

电感耦合等离子体原子发射光谱法同时测定高强度玻璃纤维粉体中9种金属元素

建立电感耦合等离子体原子发射光谱法测定高强度玻璃纤维粉体中铝、镁、钙、铁、钛、锂、铈、钠、钾9种金属元素含量的方法。采用氢氟酸、高氯酸和盐酸分两段溶解样品,分别在选定的各元素分析谱线下,采用电感耦合等离子体原子发射光谱仪测定各元素含量。9种金属元素在各自的质量浓度范围内与光谱强度成良好的线性关系,相关系数均大于0.999,检出限为8.0~17.4 μg/g。测定结果的相对标准偏差小于1.8%(n=6),加标回收率为97.6%~103.7%。该方法准确,简便,快速,适用于高强度玻璃纤维中多金属元素的同时测定。     

电感耦合等离子体原子发射光谱法测定工业电解质中钙、镁、锂

工业电解质中微量元素钙、镁、锂对电解槽的正常运行非常重要。本文采用高氯酸加热挥发除氟,以盐酸(1 1)溶解残渣,选用Ca317.9nm、Mg297.5nm、Li670.7nm作为分析谱线,考察了样品处理方法、共存元素干扰对测定结果的影响。建立了电感耦合等离子体原子发射光谱法测定工业电解质中钙、镁、锂的方法。结果表明：不同的电解质因其所含氧化铝的不同会有部分不溶杂质,但对微量元素的测定影响很小,可以忽略不计。共存元素铝和钠不干扰微量元素的测定。按照试验方法对2个电解质标准样品进行了测定,其测定值与标准值吻合。同时对不同电解槽的工业电解质样品进行了分析,其结果的相对标准偏差(RSD,n=11)在0.69%-5.68%之间,满足生产分析的需要。     

Parametric study of atmospheric-pressure diamond synthesis with an inductively coupled plasma torch

Polycrystalline diamond coatings have been deposited run molybdenum and silicon substrates using an inductively coupled, atmospheric-pressure plasma torch. Growth rates are on the order of 10 hr. The inductively coupled plasma reactor is found to produce a uniform, well-characterized growth environment for experimental and computational .study of the atmospheric-pressure diamond growth regime. Growth morphology is found to be sensitive to reactor conditions such as substrate surface temperature and methane-to-hydrogen feed ratio. An experimental parametric study of these variables is performed and the resultant growth analyzed by scanning electron microscopy, Raman spectroscopy, and X-ray diffraction Spectroscopic analysis of the gas phase is also performed. Results indicate that the, substrate temperature range over which diamond growth occurs shifts toward higher temperatures as the methane-to-hydrogen feed ratio is increased. The growth rate is observed to reach a maximum with varying methane-to-hydrogen feed ratio at constant substrate temperature. Raman analysis of the deposits indicates that higher-quality diamond is achieved at the highest limits of substrate temperature for a given methane-to-hydrogen ratio. Higher-quality diamond is also observed to be, formed at lower methane-to-hydrogen feed ratios.     

An evaluation of reversed-phase and ion-exchange chromatography for use with inductively coupled plasma—mass spectrometry for the determination of organotin compounds

An evaluation of reversed-phase high-performance liquid chromatography (HPLC) employing mobile phases compatible with direct coupling to inductively coupled plasma-mass spectrometry (ICP-MS) is described for the selective and sensitive detection of organotin species. The findings of this study are compared with established methods, employing ion-exchange chromatography. In order to achieve optimum performance, both the HPLC and ICP-MS were optimized for speciation work. The results from studies using various mobile phases for the separation of a range of tin compounds (inorganic tin, tributyltin, dibutyltin and monobutyltin) are discussed both in terms of resolution and compatibility with ICP-MS instrumentation. Tropolone, a commonly used complexing agent for organotin species, is also discussed with reference to the chromatographic separation of tin species. Finally, the role of isotope dilution analysis in conjunction with HPLC-ICP-MS for organotin speciation is described with respect to the European Community Standards, Measurements and Testing (BCR) certified material programme.     

等离子体发射光谱法测定矿山水样中硫酸盐的研究

水质中硫酸盐的测定方法很多,但对于成分复杂且盐分很高的矿山水样,传统方法操作繁琐且不环保,本文建立了等离子体发射光谱法测定矿山水样中硫酸盐的方法,样品采用硝酸和盐酸进行加热消解后既可去除硫化物,降低水质的黏度,又可实现多元素同时测定。该方法检出限为0.03mg/L,相对标准偏差为0.1～0.4%(n=6),方法具有方便,快捷,检出限低,精密度、准确度高且线性范围广的优点。     

电感耦合等离子体发射光谱法检测镍基/钴基高温合金中硼磷硅

采用一定比例的混合酸溶解样品,利用基体匹配配制一系列标液消除基体的影响,以及轴向观测喷嘴吹扫技术来提高待测元素的灵敏度,使用电感耦合等离子体发射光谱(ICP-OES)测定镍基/钴基高温合金中硼磷硅。各元素选的分析线依次为B 182.577 nm、P 178.222 nm、Si 185.005 nm。检测范围分别是：B：0.001%-3.0%,P：0.003%-0.20%,Si：0.005%-3.0%,检出限范围是0.00005%-0.0004%,线性相关系数>0.9995。加标回收率为90.0%-105.0%,精密度RSD<2.0%。该方法操作简单快速,结果令人满意。     

电感耦合等离子体质谱(ICP-MS)法测定地质样品中Cu和Zn的干扰研究

电感耦合等离子体质谱(ICP-MS)法标准模式测定地质样品中Cu和Zn时,样品溶液中Ti在高温下易形成TiO⁺和TiOH⁺产生离子重叠干扰,使测定值偏离真值而影响测定结果。采用氢氟酸-高氯酸-硝酸消解、王水复溶样品,通过多级在线校正⁴⁶Ti¹⁶O⁺,消除TiO⁺和TiOH⁺离子重叠干扰,研究了单质Ti与⁴⁶Ti¹⁶O⁺、质荷比63、64、65、66离子间存在的关系,建立了一种电感耦合等离子体质谱(ICP-MS)法测定地质样品中Cu和Zn的分析方法。结果表明：单质Ti对Cu和Zn产生的干扰值与其质量浓度呈非简单的正相关性,TiO⁺产生的干扰离子质荷比65离子强度比63高,质荷比64离子强度比66高;⁴⁶Ti¹⁶O⁺对质荷比63、66离子干扰增量值与单质Ti质量浓度变化无关;^6...