单分散α-Fe_2O_3纳米结构空心亚微球的制备及表征

采用一种新的溶液生长法结合多步包覆法在自制的不同粒径SiO2单分散亚微球表面包覆不同厚度的β-FeOOH涂层,得到单分散β-FeOOH/SiO2核壳结构亚微球.实验结果表明,SiO2核心颗粒尺寸对表面涂层的形态和包覆均匀性有很大影响.当SiO2核心颗粒的平均粒径为250 nm左右时,β-FeOOH表面涂层均匀,颗粒间团聚较少,一次包覆后涂层厚度约为35 nm.涂层中β-FeOOH纳米棒的尺寸随着所选SiO2核心颗粒粒径的增大而相应增大.经多次包覆能够显著提高涂层的厚度,3次包覆后β-FeOOH表面涂层厚约100 nm.β-FeOOH/SiO2核壳结构亚微球与质量分数5%的NaOH溶液反应后,于600℃焙烧2 h得到了单分散α-Fe2O3空心微球.单分散α-Fe2O3空心亚微球表层是由α-Fe2O3纳米棒搭建而成的三维网络结构,α-Fe2O3纳米棒的尺寸与核壳结构中β-FeOOH纳米棒的尺寸基本一致.     

超高温焙烧的Ni/Al2O3对甲烷部分氧化反应的催化活性

考察了超高温焙烧的Ni/Al2O3对甲烷部分氧化反应的催化性能,发现该催化剂经还原后对甲烷部分氧化反应表现出较高的催化活性.X射线衍射结果显示,Ni/Al2O3催化剂在超高温(1200~1400℃)下焙烧后生成了NiAl2O4,且无相转移,进一步经950℃还原后催化剂中绝大部分Ni以单质Ni0形式存在.透射电子显微镜测试结果表明,不同超高温焙烧的催化剂经950℃还原后Ni晶粒的大小无明显差异.这说明超高温焙烧的Ni/Al2O3对甲烷部分氧化反应的高活性可归结为NiAl2O4的可还原性以及还原后Ni0相似的晶粒尺寸.同时还发现,焙烧温度越高,生成的NiAl2O4的还原温度越高.     

Mo-La_2O_3阴极碳化层组织结构研究

采用高分辨透射/扫描电镜,X射线衍射和俄歇探针等分析手段对实用型的FU-6051电子管的碳化Mo-La2O3阴极显微组织结构进行了观察分析。碳化Mo-La2O3阴极碳化层为疏松多孔的Mo2C块状组织,其中有许多垂直于丝轴方向的晶界与孔洞串,相互贯通直至阴极表面。碳化层与芯部基体钼结合良好,两者间无明显的过渡层。活性物质La2O3在阴极的碳化层和基体中分布均匀,但在阴极表面有相当程度的富集。La2O3在碳化层中以两种方式存在:在晶界、孔洞中以微米级的颗粒富集,在Mo2C晶体内部弥散分布纳米级La2O3粒子。     

α-Fe_2O_3纳米立方体和纳米棒组装空心微球的可控合成及其磁学性能

在0.15mol/LCl-和0.05mol/LSO42-的存在下,通过Fe3 溶液140℃水热反应12h分别得到α-Fe2O3纳米立方体和α-FeOOH纳米棒自组装的微球,将得到的α-FeOOH纳米棒自组装微球经600℃热处理2h后转化为α-Fe2O3纳米棒组装空心微球.利用X射线衍射仪、扫描电子显微镜、透射电子显微镜和红外光谱对所得产物进行表征和分析.结果表明,所制备的单分散的α-Fe2O3纳米立方体为六方单晶结构,其边长为500nm.直径为2~4.5μm的空心微球是由直径约150nm的α-Fe2O3纳米棒组装而成.研究了Cl-和SO42-在纳米立方体和空心微球形成过程中的作用,提出了可能的生长机理.在室温下测试了α-Fe2O3纳米立方体和α-Fe2O3纳米棒自组装微球的磁学特性,其矫顽力和剩余磁化强度分别为2858.3Oe(1Oe=79.58A/m)和0.195emu·g-1(1emu·g-1=15.7914×10-9A·m2·kg-1),218.87Oe和0.071emu·g-1.     

铝酸盐蓝色荧光粉的热劣化及机制研究

研究了Ba1-xMgAl10:xEu2+(BAM)在空气中热处理后的荧光衰减特性和机制.结果表明:经600℃热处理1～5 h以及分别经700,800和900℃热处理1 h后,蓝光和绿光发射强度都减弱,红光发射不明显.经1000℃热处理1h后,在蓝光和绿光发射强度减弱的同时,出现了明显的红光发射.因此,600～900℃热处理时,BAM的热劣化是由Eu2+迁移和聚集所致.由于O2在荧光粉表面形成吸附氧(O),荧光粉β-Al2O3结构的镜面层中的Eu2+向吸附氧表面迁移并聚集,使Eu2+的晶体场改变以及Eu2+之间的能量传递加剧导致无辐射跃迁几率增加,蓝光发射减弱;类似地,尖晶石胞中Eu2+迁移到镜面层,导致绿光发射减弱.1000℃下热处理时,Eu2+被临近的O氧化,出现Eu3+红光特征发射,加剧了材料的劣化.     

Fe3O4的X射线微结构特征与催化活性间的关系

湿法工艺制备的不同晶型Fe2O3, 经水煤气还原后Fe3O4的X射线衍射微结构特征, 用分析微应变和晶粒尺寸的Voigt函数单峰分析法进行了测定。Fe3O4微应变大小同催化活性间存在一种对应关系。γ-Fe2O3还原的Fe3O4比α型还原的有更大的晶格畸变, 在325℃, 500空速条件下, CO转化率达97%以上, 比后者高出30%多。这种畸变结构在工业催化反应条件下能长期稳定, 但经600℃高温处理后, 畸变减小,活性下降。湿法工艺可以获得具有不同活性的Fe3O4前身, γ-Fe2O3与Fe3O4晶体结构上的类似, 使它在还原过程中, 能把这种高活性的结构状态保留下来。     

α-Fe2O3纳米立方体和纳米棒组装空心微球的可控合成及其磁学性能

在0．15mol／L Clˉ和0．05mol／L SO4^2-的存在下,通过Fe^3＋溶液140℃水热反应12h分别得到α—Fe2O3纳米立方体和α-FeOOH纳米棒自组装的微球,将得到的α-FeOOH纳米棒自组装微球经600℃热处理2h后转化为α—Fe2O3纳米棒组装空心微球．利用X射线衍射仪、扫描电子显微镜、透射电子显微镜和红外光谱对所得产物进行表征和分析．结果表明,所制备的单分散的α-Fe2O3纳米立方体为六方单晶结构,其边长为500nm．直径为2～4．5μm的空心微球是由直径约150nm的α-Fe2O3纳米棒组装而成．研究了Clˉ和SO4^2-在纳米立方体和空心微球形成过程中的作用,提出了可能的生长机理．在室温下测试了α-Fe2O3纳米立方体和α-Fe2O3纳米棒自组装微球的磁学特性,其矫顽力和剩余磁化强度分别为2858.3 Oe（1 Oe=79．58 A／m）和0．195emu．g^-1（1 emu．g^-1=15．7914×10^-9 A·m^2·kg^-1）,218．87 Oe和0．071 emu．g^-1．     

硼酸镧纳米棒的制备及其在植物油中的抗磨减摩性能

以Na2B4O7·10H2O和La(NO3)3·6H2O作原料,油酸作改性剂,采用水热法制备了硼酸镧纳米棒。利用X-衍射仪、FT-IR光谱仪、扫描电镜及能谱仪对其结构进行了表征,采用四球摩擦试验机考察了其在植物油中的抗磨减摩性能,利用扫描电镜观察了钢球表面磨斑的形貌,X射线光电子能谱测定了磨斑的元素组成。结果表明,硼酸镧呈纳米棒结构,其直径为50 nm、长达500 nm。硼酸镧纳米棒能显著提高植物油的抗磨、减摩性能,当添加剂的含量为1wt.%时,植物油的抗磨、减摩性能达到最佳。XPS分析结果表明,在钢球表面形成了一层含油酸的吸附膜和一层含Fe2O3、B2O3和La2O3等物质的润滑膜,这种润滑膜起到了良好的润滑作用。     

Ba、Mn对Al2O3热稳定性和甲烷催化燃烧活性的影响

采用溶胶-凝胶法制备BaO•6Al2O3系列催化剂.考察了Ba、Mn的引入对Al2O3的热稳定性及甲烷催化燃烧性能的影响.结果表明, Ba在高温下与Al2O3首先生成BaAl2O4，然后进一步与Al2O3反应生成具有β-Al2O3结构的BaAl12O19六铝酸盐，抑制了Al2O3进一步的烧结，提高了催化剂的热稳定性. Mn的引入也能够促进六铝酸盐的生成并提高催化剂的甲烷燃烧活性.采用超临界干燥法可抑制干燥过程中因毛细收缩引起的比表面积降低.所制备的BaMnAl11O19催化剂经1200 ℃焙烧4 h后，比表面积为35.1 m2•g－1，在空速40000 h－1条件下，10％甲烷转化温度(T10％)为500 ℃，催化活性明显高于常规干燥法制备的相应催化剂.     

预处理条件对La_2O_3上过氧物种光诱导生成的影响

采用原位显微Raman光谱技术详细考察了焙烧温度和焙烧时间对La(OH)3分解制备的La2O3结构以及过氧物种光诱导生成性能的影响,结果表明,经700℃焙烧所得La2O3样品较经800℃以上长时间焙烧的样品更有利于过氧物种的生成.对La(OH)3热分解过程的原位XRD测试结果表明,焙烧温度需达到近700℃才可使La(OH)3完全转化为La2O3.在700℃焙烧的样品上,除了六方相的La2O3外,还可检出介稳态的立方相La2O3.经800℃以上长时间(≥5 h)焙烧后,介稳态的立方相La2O3将转化为稳定的六方相La2O3物种.在相同的实验条件下,立方相的稀土倍半氧化物较六方相更有利于过氧物种的光诱导生成,其原因可能源于前者含更多氧空位,因而更有利于对分子氧的吸附和活化.     

多环芳二酐型聚酯亚胺膜的透气性能

多环芳二酐型聚酯亚胺膜的透气性能李悦生，丁孟贤，徐纪平（浙江大学高分子科学与工程研究所，杭州，３１００２７）（中国科学院长春应用化学研究所）关键词聚醚酰亚胺，聚酯酰亚胺，膜，透气性通常的聚酰亚胺加工性能较差，在芳环二酐的苯环间引入醚键等柔性基团后，其...     

微量元素与疾病诊断治疗的研究现状及展望

对国内外微量元素与疾病的关系及其诊断治疗的研究现状及研究动向进行了综述，包括：微量元素与地方病、癌肿、心血管病、糖尿病、眼病、神经系统病等。参考文献72篇。     

Determination and study on residue and dissipation of benazolin-ethyl and quizalofop-p-ethyl in rape and soil

A QuEChERS (quick, easy, cheap, effective, rugged, and safe) method for the determination of benazolin-ethyl and quizalofop-p-ethyl in rape and soil by high-performance liquid chromatography-tandem mass spectrometry has been developed in this study. The residue and dissipation of benazolin-ethyl and quizalofop-p-ethyl in rape and soil were determined with the developed method. The half-lives of benazolin-ethyl in rape straw and soil were 3.7–5.1 days and 14.3–26.3 days, respectively. The half-lives of quizalofop-p-ethyl in rape straw and soil were 5.0-6.1 days and 0.3–9.7 days, respectively. The residue of benazolin-ethyl and quizalofop-p-ethyl in rapeseed and soil were below the detection limit (i.e., 0.5?mg?kg^?1, the maximum residue level of European Union for quizalofop-p-ethyl).     

Synthesis and Optical and Redox Properties of Symmetric and Asymmetric BODIPYs

Herein, we present the synthetic route and the photophysical, electrochemical as well as laser properties of novel red‐emitting boron‐dipyrromethenes (BODIPYs) bearing arylethyne moieties. Such functionality is added along the main axis of the chromophore leading to single‐ and double‐substituted derivatives. The relationship between the dye structure and the lasing properties is studied in detail with the help of the photophysical and electrochemical properties as well as quantum mechanical simulations. The asymmetric substitution of the parent dye induces inhomogeneities in the charge distribution, which leads to an overall loss of the fluorescence capacity, mainly in polar media. Such non‐radiative deactivation processes can be softened by decreasing the electron‐donor ability of the substituent or even avoided by symmetrical substitution. Thus, grafting of the arylethyne moieties at the longitudinal axis of the indacene core results in an effective strategy to develop red‐edge BODIPYs with highly efficient and photostable laser emission.     

Ti-V基储氢合金及其氢化物的物相结构与组分优化设计

Ti-V基储氢合金在室温、常压下即可表现出良好的储氢特性,且质量储氢容量明显高于传统AB₅型储氢合金,从而在氢气的精制和回收、运输和储存及热泵等方面有较早的应用。 此外,在混合气体分离、核反应堆中处理氢的同位素、镍氢电池及燃料电池负极材料等方面也得到了广泛的研究与关注。 基于目前Ti-V基储氢合金的研究现状,概述了该类合金的优势、限制性因素(包括成因)及改性手段。 此外,为了进一步理解Ti-V基合金储氢机理、构建合金组分与储氢特性之间的对应关系,本工作重点围绕Ti-V基储氢合金及其氢化物的结构、组分优化设计展开综述,并对其未来研究方向做出展望。     

钒与糖代谢及糖尿病

微量元素钒作为生物体内必需元素，经证实有很重要的生理学功能，与机体糖代谢有十分密切的关系，且能降低糖尿病动物模型的高血糖，极有可能被开发为治疗糖尿病的药物。     

Conformations and steric and stacking interactions of trisubstituted ureas and thioureas with alkyl and phenyl groups

The monomeric ν(N—H) vibrations of various trisubstituted ureas of the R₂UPh type and -thioureas of the R₂TUPh type have been studied. The trans—out isomerism in the former and the trans—out—cis isomerism in the latter are discussed from the point of view of steric effect. The monomeric ν(N—H) vibrations of RPhUPh and RPhTUPh are also examined. The single band appearing in the spectrum of both ureas is characteristic of the cis form; this suggests the existence of phenyl—phenyl interaction (the stacking interaction proposed by Galabov et al. [10]). Behavior of ν(N—H) vibrations at several concentrations is shown to be clearly different in the three forms (trans, out and cis). The presence of the cis form is confirmed by solvent effect experiments.     

Synthesis of Tyrosol and Hydroxytyrosol Glycofuranosides and Their Biochemical and Biological Activities in Cell-Free and Cellular Assays

Tyrosol (T) and hydroxytyrosol (HOT) and their glycosides are promising candidates for applications in functional food products or in complementary therapy. A series of phenylethanoid glycofuranosides (PEGFs) were synthesized to compare some of their biochemical and biological activities with T and HOT. The optimization of glycosylation promoted by environmentally benign basic zinc carbonate was performed to prepare HOT α-L-arabino-, β-D-apio-, and β-D-ribofuranosides. T and HOT β-D-fructofuranosides, prepared by enzymatic transfructosylation of T and HOT, were also included in the comparative study. The antioxidant capacity and DNA-protective potential of T, HOT, and PEGFs on plasmid DNA were determined using cell-free assays. The DNA-damaging potential of the studied compounds for human hepatoma HepG2 cells and their DNA-protective potential on HepG2 cells against hydrogen peroxide were evaluated using the comet assay. Experiments revealed a spectrum of different activities of the studied compounds. HOT and HOT β-D-fructofuranoside appear to be the best-performing scavengers and protectants of plasmid DNA and HepG2 cells. T and T β-D-fructofuranoside display almost zero or low scavenging/antioxidant activity and protective effects on plasmid DNA or HepG2 cells. The results imply that especially HOT β-D-fructofuranoside and β-D-apiofuranoside could be considered as prospective molecules for the subsequent design of supplements with potential in food and health protection.     

Ferrocene and ferrocenium modified clays and their styrene and EVA composites

In this work, ferrocene- and ferrocenium-containing salts were employed to modify montmorillonite. X-ray measurements show an increase in the interlayer spacing upon clay modification, which means that the larger and more organophilic cations were inserted into the gallery space of montmorillonite. Attempts to prepare nanocomposites of polystyrene and ethylene vinyl acetate copolymers lead to immiscible systems; the morphology of these systems was elucidated with TEM, XRD and cone calorimetry. The thermal stability of the composites is greater than that of the virgin polymer.