Preparative isolation of guaipyridine sesquiterpene alkaloid from Artemisia rupestris L. flowers using high-speed counter-current chromatography

Although the medicinal plant Artemisia rupestris L. has been widely researched for several decades, its alkaloids have never been isolated before. To our surprise, the alkaloids in the plant were not detected in the stems but detected in the flowers. Herein, a novel and strange guaipyridine sesquiterpene alkaloid with a carboxyl group named rupestine was purified successfully from the total alkaloids extracted from the flowers by high-speed counter-current chromatography (HSCCC). The two-phase solvent system used was composed of ethyl acetate-methanol-water (8:1:7, v/v/v). Fifty six milligrams of rupestine was obtained at over 97% purity and 95% recovery from 200 mg of the total alkaloids in one-step separation. Its structure was elucidated by spectroscopic methods including high resolution ESI-MS, (1)H NMR, (13)C NMR, Heteronuclear Multiple Bond Correlation (HMBC), Heteronuclear Single Quantum Coherence (HSQC), and Nuclear Overhauser Enhancement Spectroscopy (NOESY).     

Isolation of bitter acids from hops (Humulus lupulus L.) using countercurrent chromatography

Commercially available hops (Humulus lupulus L.) bitter acid extracts contain a mixture of three major congeners (co-, n-, and ad-) in addition to cis/trans diastereomers for each congener. Individual isomerized α-acids were obtained by the consecutive application of two separate countercurrent chromatography methods. First, individual isomerized α-acid congeners as a mixture of cis/trans diastereomers were obtained using a solvent system consisting of hexane and aqueous buffer. The second purification, capable of separating cis/trans diastereomers, was accomplished using a quaternary solvent system; an alternative procedure using β-cyclodextrin followed by countercurrent chromatography was also investigated. The NaBH(4) reduction of the purified isomerized α-acid compounds followed by countercurrent chromatography purification resulted in individual ρ iso α-acids (>95%). Similarly, catalytic hydrogenation of the purified isomerized α-acid compounds followed by countercurrent chromatography purification produced individual tetrahydro isomerized α-acids (>95%). Reported herein is a widely applicable approach that focuses on three critical variables--solvent system composition, pH, and buffer-to-sample ratio--that enable the efficient purification of individual bitter acids (≥95%) from commercially available hops extracts.     

Combined use of ionic liquid and sulfobutylether‐β‐cyclodextrin as electrolyte additives for separation and determination of camptothecin alkaloids by CZE

This work reported that ionic liquid (IL) ([Bmim] [PF₆]) and sulfobutylether‐β‐CD (SBE‐β‐CD) were used as electrolyte additives for the separation and determination of camptothecin (CPT) alkaloids by CZE. Separation parameters such as the buffer type, pH, and concentration of the running buffer, the concentration of SBE‐β‐CD and IL, temperature, and separation voltage were all investigated in order to achieve the maximum possible resolution. The four analytes were baseline separated within 10 min in capillary at the separation voltage of 15 kV with a running buffer consisting of 20 mM borate buffer, 20 mM IL, and 100 mM SBE‐β‐CD at pH 9.0. Under such conditions, good linearity about two orders of magnitudes of peak areas was achieved for the investigated CPT alkaloids with the correlation coefficients ranging from 0.9946 to 0.9985. For all analytes, detection limits (S/N = 3) and quantitation limits (S/N = 10) range from 0.05 to 0.92 μg/mL and 0.17 to 3.06 μg/mL, respectively. The proposed method has not only been successfully applied to the separation and determination of CPT alkaloids but also showed that IL seemed to be a promising additive in CZE separation.     

The influence of alpha1-acid glycoprotein on collagenase-3 activity in early rheumatoid arthritis

The concentration and glycosylation of alpha(1)-acid glycoprotein (AGP) alter significantly during inflammation. A definitive physiological role for AGP remains elusive and is the subject of extensive investigation. This study investigated the influence of AGP on the activity of collagenase-3, an important mediator of cartilage destruction in rheumatoid arthritis. AGP was isolated from normal and rheumatoid plasma. Fucosylation was determined by high pH anion-exchange chromatography; sialylation was assessed following enzymatic digest. Rheumatoid AGP displayed elevated fucosylation and sialylation compared with normal. The influence of each sample on collagenase-3 activity was measured fluorometrically. AGP influenced collagenase-3 catalysis and collagen binding, with catalytic activity correlating with fucosylation. Rheumatoid AGP exhibited less efficient inhibition than normal plasma AGP. It is hypothesized that AGP within rheumatoid synovial fluid may be inadequate to prevent excessive cartilage destruction and hence may exacerbate the disease process.     

Ionic complexes of biosynthetic poly(malic acid) and poly(glutamic acid) as prospective drug-delivery systems

The hydrolytic degradability and erythromycin release from stoichiometric ionic complexes of biotechnological poly(beta,L-malic acid)s and poly(gamma,D-glutamic acid)s with alkyltrimethylammonium surfactants were investigated. The influence of pH, temperature and antibiotic load on hydrolysis rate was examined. It was found that poly(malic acid) complexes degraded by a surface erosion mechanism at a higher rate than poly(glutamic acid) complexes, which eroded in bulk. Erythromycin was lodged in the paraffinic subphase of the complexes and upon aging it was delivered according to a sigmoidal profile that appeared to be independent on the antibiotic load.     

Foams and surface rheological properties of β-casein, gliadin and glycinin

Interfacial rheological properties and their suitability for foam production and stability of two vegetable proteins were studied and compared to β-casein. Proteins used ranged from flexible to rigid/globular in the order of β-casein, gliadin and soy glycinin. Experiments were performed at pH 6.7. Network forming properties were characterised by the surface dilational modulus (determined with the ring trough) and the critical falling film length (L_still) at which a stagnant protein film will break. Gliadin had the highest dilational modulus, followed by glycinin and β-casein, whereas glycinin formed the strongest film against fracture in the overflowing cylinder. The rate of decrease in the surface tension was studied at the air–water (Wilhelmy plate method) and the oil–water interface (bursting membrane) and the dynamic surface tension during compression and expansion in the caterpillar. Gliadin had the lowest equilibrium interfacial tensions and β-casein the lowest dynamic surface tension during expansion. Hardly any foam could be formed at a concentration of 0.1 g/l by shaking. At a concentration of 1.4 g/l most foam was formed by β-casein, followed by gliadin and glycinin. It seems that in the first place the rate of adsorption is important for foam formation. For the vegetable proteins, adsorption was slow. This resulted in lower foamability, especially for glycinin.     

Alkaloids from Hippeastrum morelianum Lem. (Amaryllidaceae)

The Amaryllidaceae family has proven to be a rich source of active molecules. As part of an ongoing project, we report a phytochemical study of Hippeastrum morelianum (Amaryllidaceae), from which we have isolated two homolycorine-type alkaloids, the new 2α,7-dimethoxyhomolycorine (1) and the poorly described candimine (2), as well as six known alkaloids: tazettine, pretazettine, 3-epimacronine, haemanthamine, hamayne and trisphaeridine. For reference purposes, the NMR of the isolated compounds was unequivocally described, based on 2D NMR measurements including (1)H-(1)H COSY, (1)H-(1)H NOESY, HSQC and HMBC.     

Simultaneous liquid chromatographic assay of amantadine and its four related compounds in phosphate-buffered saline using 4-fluoro-7-nitro-2,1,3-benzoxadiazole as a fluorescent derivatization reagent

Simultaneous HPLC assay of 1-adamantanamine hydrochloride (amantadine) and its four related compounds [2-adamantanamine hydrochloride (2-ADA), 1-adamantanmethylamine (ADAMA), 1-(1-adamantyl)ethylamine hydrochloride (rimantadine) and 3,5-dimethyl-1-adamantanamine hydrochloride (memantine)] in phosphate-buffered saline (pH 7.4) after pre-column derivatization with 4-fluoro-7-nitro-2,1,3-benzoxadiazole (NBD-F) was developed. Phosphate-buffered saline samples were mixed with borate buffer and NBD-F solution in acetonitrile at 60 degrees C for 5 min and injected into HPLC. Five derivatives were well separated from each other. The lower limits of detection of amantadine, 2-ADA, ADAMA, rimantadine and memantine were 0.008, 0.001, 0.0008, 0.0015 and 0.01 microg/mL, respectively. The coefficients of variation for intra- and inter-day assay were less than 6.4 and 8.2%, respectively. The method presented was applied to a binding study of these compounds to human alpha(1)-acid glycoprotein. While affinity constants and capacities for ADAMA, rimantadine and memantine were calculated by means of Scatchard plots, those for the others were not determined. ADAMA, rimantadine and memantine were bound with different affinities and capacities. These results indicate that NBD-F is a good candidate as a fluorescent reagent to simultaneously determine amantadine and its four related compounds by HPLC after pre-column derivatization. Our method can be applied to binding studies for protein.     

A sequence-based computational model for the prediction of the solvent accessible surface area for α-helix and β-barrel transmembrane residues

Predicting the solvent accessible surface area (ASA) of transmembrane (TM) residues is of great importance for experimental researchers to elucidate diverse physiological processes. TM residues fall into two major structural classes (α-helix membrane protein and β-barrel membrane protein). The reported solvent ASA prediction models were developed for these two types of TM residues respectively. However, this prevents the general use of these methods because one cannot determine which model is suitable for a given TM residue without information of its type. To conquer this limitation, we developed a new computational model that can be used for predicting the ASA of both TM α-helix and β-barrel residues. The model was developed from 78 α-helix membrane protein chains and 24 β-barrel membrane protein. Its prediction ability was evaluated by cross validation method and its prediction result on an independent test set of 20 membrane protein chains. The results show that our model performs well for both types of TM residues and outperforms other prediction model which was developed for the specific type of TM residues. The prediction results also proved that the random forest model incorporating conservation score is an effective sequence-based computational approach for predicting the solvent ASA of TM residues.     

新型含苯并噻唑α-氨基膦酸酯类化合物在淀粉类手性固定相上的液相色谱分离

本文运用涂敷型(Chiralpak AD-H)和键合型(Chiralpak IA)两种淀粉类手性固定相高效液相色谱法,进行了新型含苯并噻唑α-氨基膦酸酯类化合物的手性分离。从色谱分离的保留因子(k)、分离系数(α)和分离度(Rs)三个方面考察了两种类型色谱柱的分离性能,上述化合物在Chiralpak IA柱上能够得到较好的基线分离。同时,讨论了温度、流动相极性和目标分析物的结构等因素对Chiralpak IA柱分离性能的影响。由于键合型固定相较稳定的性能,使某些非常规的溶剂(如THF)成功地应用于手性α-氨基膦酸酯类化合物的分离。     

Chiral separation of dansyl amino acids in capillary electrophoresis using mono-(3-methyl-imidazolium)-beta-cyclodextrin chloride as selector

Enantioseparations of fourteen dansyl amino acids were achieved by using a positively-charged single-isomer beta-cyclodextrin, mono-(3-methyl-imidazolium)-beta-cyclodextrin chloride, as a chiral selector. Separation parameters such as buffer pH, selector concentration, separation temperature, and organic modifier were investigated for the enantioseparation in order to achieve the maximum possible resolution. Chiral separation of dansyl amino acids was found to be highly dependent on pH since the degree of protonation of these amino acids can alter the strength of electrostatic interaction and/or inclusion complexation between each enantiomer and chiral selector. In general, the chiral resolution of dansyl amino acids was enhanced at higher pH, which indicates that the carboxylate group on the analytes may interact with the imidazolium group of cationic cyclodextrin. For most analytes, a distinct maximum in enantioresolution was obtained at pH 8.0. Moreover, the chiral separation can be further improved by careful tuning of the separation parameters such as higher selector concentration (e.g. 10 mM), lower temperature, and addition of methanol. Enantioseparation of a standard mixture of these dansyl amino acids was further achieved in a single run within 30 min.     

Simultaneous separation of eight beta-adrenergic drugs using titanium dioxide nanoparticles as additive in capillary electrophoresis

The analysis is described for separating seven beta-adrenergic blocking agents (atenolol, celiprolol, clorprenaline, fenoterol, metoprolol, propranolol, terbutaline) and clenbuterol (sympathomimetic beta-2 receptor stimulating agonist, decongestant and bronchodilator, illicit anabolic used in athletics) by CE with UV detection. In order to simultaneously separate all analytes, Tris-H3PO4 solution was applied containing titanium dioxide nanoparticles (TiO2 NPs) as BGEs. The effects of important factors, such as concentration of TiO2 NPs, optimum pH, run buffer concentration, and separation voltage, were investigated so as to achieve best CE separation. The eight analytes could be well separated applying a separation voltage of 15 kV in 75 mM Tris-H3PO4 buffer at a pH of 2.40, containing 6.0 x 10(-6) g/mL TiO2 NPs. Under these optimal conditions, the RSDs for peak areas and for migration times were less than 2.7 and 2.3%, respectively. The detection limits were 0.1 microg/mL for celiprolol, 0.1 microg/mL for propranolol, 0.2 microg/mL for fenoterol, 1.0 microg/mL for atenolol, 1.0 microg/mL for clenbuterol, 1.0 microg/mL for clorprenaline, 1.0 microg/mL for metoprolol, and 1.0 microg/mL for terbutaline. The proposed method was successfully applied for the rapid CE determination of the frequently applied antihypertensive beta-blocking compounds atenolol, metoprolol, terbutaline, and propranolol in pharmaceutical tablets.     

Immunoaffinity purification of α-momorcharin from bitter melon seeds (Momordica charantia)

α‐Momorcharin (α‐MMC), a type I ribosome‐inactivating protein (RIP), has shown therapeutic potential such as anti‐tumor and anti‐viral agent. Traditional process of α‐MMC purification from bitter melon seeds was time consuming and low efficient. To take this challenge, we made an affinity matrix by coupling the monoclonal antibody (McAb) with Sepharose 4B. Using this attractive strategy, 196 mg of α‐MMC was obtained from 100 g of bitter melon seeds as the starting material. The yield of the protein was 2.7%. The homogeneity and properties of the protein were assessed by SDS‐PAGE, acidic PAGE, RP‐HPLC and N‐terminal sequence as well as Western blot. Purified α‐MMC showed remarkable inhibition to the melanoma cell line JAR and EMT‐62058. In addition, it also displayed obvious inhibition on hepatitis B virus (HBV). This work provided a simple, rapid and efficient approach for α‐MMC purification from Momordica charantia.     

Open-pore biodegradable foams prepared via gas foaming and microparticulate templating

Open-pore biodegradable foams with controlled porous architectures were prepared by combining gas foaming and microparticulate templating. Microparticulate composites of poly(epsilon-caprolactone) (PCL) and micrometric sodium chloride particles (NaCl), in concentrations ranging from 70/30 to 20/80 wt.-% of PCL/NaCl were melt-mixed and gas-foamed using carbon dioxide as physical blowing agent. The effects of microparticle concentration, foaming temperature, and pressure drop rate on foam microstructure were surveyed and related to the viscoelastic properties of the polymer/microparticle composite melt. Results showed that foams with open-pore networks can be obtained and that porosity, pore size, and interconnectivity may be finely modulated by optimizing the processing parameters. Furthermore, the ability to obtain a spatial gradient of porosity embossed within the three-dimensional polymer structure was exploited by using a heterogeneous microparticle filling. Results indicated that by foaming composites with microparticle concentration gradients, it was also possible to control the porosity and pore-size spatial distribution of the open-pore PCL foams.     

Human liver dihydrodiol dehydrogenase 1-catalyzed reaction generating 9alpha,11beta-prostaglandin F2 from prostaglandin D2 followed by micellar electrokinetic chromatography

An enzyme reaction converting prostaglandin D2 (PGD2) into 9alpha,11beta-prostaglandin F2 (9alpha,11beta-PGF2) by a human liver-originated recombinant dihydrodiol dehydrogenase 1 (DD1) has been studied using CE. Four prostaglandins, viz. PGD2, 9alpha,11beta-PGF2, PGE2, and PGF2a (see Fig. 1, the latter two major PGs are possibly coexisting compounds in the assay mixtures), were completely separated by using SDS or PEG as buffer additives. Because analysis times in the SDS system were shorter than in the PEG system, SDS was employed in measurements of the enzyme activity of DD1. The pH dependence and the reaction temperature dependence of enzyme activity have been studied. The present method enabled us to detect all of the participants in the enzyme reaction: PGD2, 9alpha,11beta-PGF2, nicotinamide adenine dinucleotide phosphate (NADPH), and NADP+. Thus, direct, comprehensive, and reliable analysis of the enzyme reaction becomes possible. Enzyme activity has hitherto been estimated indirectly from the decrease of fluorescence derived from NADPH as an index of progress of the enzyme reactions in batch methods employed in conventional studies. In addition, the low sample consumption characteristic of CE should be a significant advantage of the present method in characterization of less commonly available enzymes such as the recombinant species used in this work.     

Use of SDS micelles for improving sensitivity, resolution, and speed in the analysis of beta-lactam antibiotics in environmental waters by SPE and CE

This study dealt with the potential of MEKC with LIF detection involving derivatization with sulfoindocyanine succinimidyl ester (Cy5) for the separation and determination of beta-lactam antibiotics (ampicillin, amoxicillin, cephradine, and cephalexin) in environmental water samples. Water samples of 50 mL were enriched by SPE by passage through a weak base-cation Amberlite(R) IRA-93 exchange column. SDS micelles play important roles in the whole analytical process by improving the yield (sensitivity) and the kinetics of the labeling reaction, the elution of the retained antibiotics from the SPE preconcentration system and the electrophoretic resolution of their Cy5-derivatives. The optimum procedure includes a derivatization step of the antibiotics at 25 degrees C for 10 min and direct injection for MEKC analysis, which is conducted within about 15 min using 15 mM SDS in the running buffer (35 mM sodium borate at pH 9.3). LODs from 30 to 45 ng/L and RSDs (within-day precision) from 3.5 to 5.9% were obtained for the antibiotics in water samples with average recoveries ranging from 96.4 to 99.4%. These results indicate that the method proposed is a straightforward and sensitive tool for the determination of these antibiotics in environmental water samples providing similar quantitative results to those using more expensive equipment like LC-electrospray MS/MS.     

An efficient strategy based on liquid‐liquid extraction and pH‐zone‐refining counter‐current chromatography for selective enrichment,separation, and purification of alkaloids and organic Acids from natural products

This study presents an efficient strategy based on liquid‐liquid extraction and pH‐zone‐refining counter‐current chromatography for selective enrichment, separation, and purification of alkaloids and organic acids from natural products. First, an acid or base modified two‐phase solvent system with maximum or minimum partition coefficient was developed for the liquid‐liquid extraction of the crude extract. As a result, alkaloids or organic acids could be selectively enriched in the upper or lower phase. Then pH‐zone‐refining counter‐current chromatography was employed to separate and purify the selectively enriched alkaloids or organic acids efficiently. The selective enrichment and separation of five bufadienolide from toad venom of Bufo marinus was used as an example to show the advantage of this strategy. As a result, 759 mg of selectively enriched bufadienolide was obtained from 2 g of crude extract and the total content of five targets was increased from 14.64 to 83%. A total of 31 mg of marinobufagin‐3‐adipoyl‐l ‐arginine, 42 mg of telocinobufagin‐3‐pimeloyl‐l ‐arginine, 51 mg of telocinobufagin‐3‐suberoyl‐l ‐arginine, 132 mg of marinobufagin‐3‐suberoyl‐l ‐arginine, and 57 mg of bufalin‐3‐suberoyl‐l ‐arginine were all simultaneously separated from 500 mg of selectively enriched sample, with the purity of 92.4, 97.5, 90.3, 92.1, and 92.8%, respectively.     

Simultaneous enantioseparation of four beta2-agonists by capillary electrophoresis with cyclodextrin additives. Study of the enantioselective mechanism

The simultaneous capillary electrophoretic enantioseparation of adrenergic beta(2)-agonists enantiomers (trantinterol, mabuterol, clenbuterol, bambuterol) was studied with beta-cyclodextrin, ethyl-beta-CD, methyl-beta-CD, hydroxypropyl-beta-CD, and hydroxyethyl-beta-CD as chiral selector. The type and concentration of the chiral selector and buffer pH played a very important role in the enantioseparation of the analyzed compounds. Hydroxypropyl-beta-CD was found to be the most effective complexing agent and allowed excellent chiral/achiral resolutions compared to the other CDs. The simultaneous enantioseparation of four beta(2)-agonists was achieved using 100 mM citric acid-10 mM Na(2)HPO(4) buffer at pH 2.5 containing 120 mM hydroxypropyl-beta-CD with an applied voltage of 20 kV. Method validation in terms of repeatability, linearity, and limits of detection and quantification was performed. The effect of structural features of analytes on R(s) and t(m) was studied. Complexation binding constants for the interactions between the four compounds and three different CDs were evaluated for elucidating the enantioseparation mechanism. It was found that very small differences in the chemical structure of the analytes resulted in significant changes in stereoselective recognition.     

Structural determination of a new 2(3 --> 20)abeotaxane with an unusual 13beta-substitution pattern and a new 6/8/6-ring taxane from Taxus cuspidata

A new 2(3 --> 20)abeotaxane with an unusual 13beta-substitution pattern and a new 6/8/6-ring taxane were isolated from the methanol extract of the needles of Taxus cuspidata. The structures were established as 2alpha,7beta-diacetoxy-5alpha,10beta,13beta-trihydroxy-2(3 --> 20)abeotaxa-4(20), 11-dien-9-one (1) and 2alpha,5alpha,7beta,9alpha,13alpha-pentahydroxy-10beta-acetoxytaxa-4(20),11-diene (2) on the basis of 1D and 2D NMR spectral data and high-resolution FAB-MS analyses.