Catalytic kinetic spectrophotometry for the determination of trace amount of oxalic acid in biological samples with oxalic acid-rhodamine B-potassium dichromate system

A new catalytic kinetic spectrophotometric method was proposed for determining trace oxalic acid based on the catalytic effect of oxalate on the oxidation of potassium dichromate with rhodamin B in 0.10 M of sulfuric acid. Good linearity is obtained over the concentration range 0.40-6.0 microg/mL of oxalic acid. After the reactions of the catalytic and non-catalytic systems were terminated by using 2.00 mL of 4 M sodium hydroxide solution, they can be stable for 3 h at room temperature. The apparent activation energy of the catalytic reaction is 12.44 kJ/mol. The effect of 50 coexisting substances was observed. The method was used to determine trace oxalic acid in tea, spinach and urine samples with satisfactory results.     

Spectrofluorimetric determination of irinotecan in the presence of oxidant agents and metal ions

In this work four spectrofluorimetric methods for the determination of irinotecan (CPT-11) in human urine and pharmaceuticals have been developed. Initially, the fluorescent characteristics of irinotecan (CPT-11) have been studied in both acidic and basic media. Later, the fluorescence emission generated by the oxidation of CPT-11 with several agents was studied. A quenching of fluorescence could be observed in the presence of Ce(IV) and I₂/I⁻. Also, the reaction between several divalent and trivalent metal ions with CPT-11 was studied, and one method in presence of Fe³⁺ was developed since it was the only metal ion that changes the fluorescence of the analyte. The proposed methods present limit of detection comprises between 0.46 and 2.57 ng mL⁻¹. The spectrofluorimetric methods were applied to human urine. No pre-treatment of the sample was necessary, only a dilution 1:20 with water was made. No interference of the matrix was observed in the conditions used. Recoveries were comprises between 100.0 and 104.3%. Also, pharmaceuticals preparations were analyzed with recoveries between 106.7 and 119.7%. The proposed spectrofluorimetric methods were validated by RP-HPLC, obtaining that the oxidation with iodine is the best method to analyze urine samples, while than, the fluorimetric method developed at acidic pH value is the best for the analysis of pharmaceuticals.     

Clean up Procedures for Determination of Amphetamine in Urine Samples.

ABSTRACT

A comparative study of the main sample preparation techniques used for spectrofluorimetric amphetamine determination in urine is presented. The advantages and disadvantages of three procedures based on liquid-liquid or solid-liquid extraction are tested, and a method for amphetamine determination in presence of methamphetamine and its metabolites is proposed. The results obtained are in agreement with the theoretical contents (spiked samples) or the results provided by a reference (GC) method (r8543161 sample).     

Determination of zinc by flow injection with fluorimetric detection in a micellar medium

A room-temperature flow injection spectrofluorimetric method is presented for the determination of Zn(II), based on the use of salicylaldehyde thiocarbohydrazone in the presence of Triton X-100 and sodium acetate-acetic acid buffer. Various physical and chemical variables affecting the reaction in the flow system were evaluated. The proposed method is very selective. The calibration graph is linear over the range 10-1000 ng/ml, with a detection limit of 5 ng/ml and a relative standard deviation at the 50 ng/ml level of 1.8 %. The method was successfully applied to the determination of Zn(II) in drinking waters and biological samples.     

Determination of zinc by flow injection with fluorimetric detection in a micellar medium

A room-temperature flow injection spectrofluorimetric method is presented for the determination of Zn(II), based on the use of salicylaldehyde thiocarbohydrazone in the presence of Triton X-100 and sodium acetate-acetic acid buffer. Various physical and chemical variables affecting the reaction in the flow system were evaluated. The proposed method is very selective. The calibration graph is linear over the range 10–1000 ng/ml, with a detection limit of 5 ng/ml and a relative standard deviation at the 50 ng/ml level of 1.8 %. The method was successfully applied to the determination of Zn(II) in drinking waters and biological samples.     

Improved gas chromatography methods for micro-volume analysis of haloacetic acids in water and biological matrices

A fast headspace solid-phase microextraction gas chromatography method for micro-volume (0.1 mL) samples was optimized for the analysis of haloacetic acids (HAAs) in aqueous and biological samples. It includes liquid-liquid microextraction (LLME), derivatization of the acids to their methyl esters using sulfuric acid and methanol after evaporation, followed by headspace solid-phase microextraction with gas chromatography and electron capture detection (SPME-GC-ECD). The derivatization procedure was optimized to achieve maximum sensitivity using the following conditions: esterification for 20 min at 80 degrees C in 10 microL methanol, 10 microL sulfuric acid and 0.1 g anhydrous sodium sulfate. Multi-point standard addition method was used to determine the effect of the sample matrix by comparing with internal standard method. It was shown that the effect of the matrix for urine and blood samples in this method is insignificant. The method detection limits are in the range of 1 microg L(-1) for most of the HAAs, except for monobromoacetic acid (MBAA) (3 microg L(-1)) and for monochloroacetic acid (MCAA) (16 microg L(-1)). The optimized procedure was applied to the analysis of HAAs in water, urine and blood samples. All nine HAAs can be separated in < 13 min for biological samples and < 7 min for drinking water samples, with total sample preparation and analysis time < 50 min. Analytical uncertainty can increase dramatically as the sample volume decreases; however, similar precision was observed with our method using 0.1 mL samples as with a standard method using 40 mL samples.     

三维荧光二阶校正法用于尿液样中氢化可的松的定量测定

本文提出了三维荧光光谱结合二阶校正算法实现人体尿液样中氢化可的松定量测定的新方法。氢化可的松本身的荧光较弱,但与浓硫酸反应后可以生成强荧光的化合物。利用这一特性,采用浓硫酸为氧化剂,设定在激发波长为300-370nm、发射波长为400-580nm范围内测定尿液样中氢化可的松的三维荧光光谱,构建三维响应数据阵,然后运用基于三线性分解的二阶校正算法进行解析。当组分数N取3时,采用基于平行因子分析（PARAFAC）算法的Z-阶校正法的平均回收率为98.6&#177;4.1％,预测残差平方根（RMSEP）为0.0114;采用基于满秩平行因子分析（FRA-PARAFAc）算法的二阶校正法的平均回收率和RMSEP分别为99.3&#177;2.4％和0.0066。两种算法可以得到相近且满意的结果。     

Spectrofluorimetric determination of tetracycline and anhydrotetracycline in serum and urine.

A spectrofluorimetric method, involving alkaline degradation and formation of a magnesium complex, is described for the determination of tetracycline (TC) and anhydrotetracycline (ATC) in their mixed solution. Tetracycline is degraded and determined in alkaline solution. This treatment of ATC produces almost no fluorescence, but a fluorescent magnesium complex forms at pH 7.5. Several synthetic samples of TC and ATC, with TC:ATC ratios ranging from 50:1 to 1:50, were analysed. The recoveries of TC and ATC are about 71-76 and 61-63% in serum, respectively, and are all about 100% in urine.     

Determination of methylbenzoquate in premixes and animal feeds using liquid chromatography with fluorescence detection

A rapid analytical procedure was developed and tested for routine identification and quantification of methylbenzoquate in feeds by liquid chromatography (LC). The ground feed samples were extracted using methanol-water (80 + 20, v/v) at 65 degrees-70 degrees C in a water bath for premixes and in dichloromethane at 45 degrees C in a water bath for final feeds, respectively. The extract of final feeds was cleaned using solid-phase extraction on silica columns. Both the final feed and premix extracts were analyzed by reversed-phase LC on a NovaPak C18 column (3.9 x 150 mm; 4 microm) with methanol-acetonitrile-water-phosphoric acid (340 + 350 + 308 + 2, v/v) as mobile phase. Fluorescence detection was performed at excitation and emission wavelengths of 265 and 390 nm, respectively. Alternatively, post-column addition of sulfuric acid solution was used to decrease the determination limit. The recovery of methylbenzoquate, in a concentration range of 0.5-10 mg/kg, was 105.0 +/- 7.3%. The limit of quantitation, based on a signal-to-noise ratio of 10:1, was 48 microg/kg. The developed LC method was tested in an interlaboratory study. The interlaboratory repeatibility for both samples ranged from 7.1 to 10.6%; the interlaboratory reproducibility ranged from 11.7 to 15.2%. With the post-column addition of sulfuric acid, the limit of quantification was decreased by a factor of 50. Overall, the developed method is highly selective and can be used in routine analysis.     

Spectrofluorimetric determination of uric acid based on its activation of catalytic oxidation of pyronine Y

A novel kinetic spectrofluorimetric method for the determination of uric acid based on the activation effect of uric acid on the Cu(II) ion catalyzed oxidation of pyronine Y by hydrogen peroxide was developed. The influence of different buffer solutions was tested and the Britton-Robinson buffer solution with pH 2.2 was found to be the optimum. The detection limit and the linear range for uric acid are 0.09 μg mL⁻¹ and 0.3–3.0 μg mL⁻¹, respectively. The RSD for eleven determinations of 1.6 μg mL⁻¹ uric acid was 1.6 %. Satisfactory results were obtained when using this method of uric acid determination in human urine.     

碘量法测定铜冶炼烟尘中铜

试验研究了铜冶炼烟尘中铜含量的测定方法,试料用盐酸、氢氟酸、硝酸、高氯酸及硫酸分解,氢溴酸除去砷、锡、锑,硫酸除去硒的干扰。进一步对滴定条件和共存元素的干扰及消除进行了试验,最终确定了最佳条件。按照实验方法测定6个铜冶炼烟尘样品中铜量,结果的相对标准偏差为0.22%~0.65%,精密度高,准确度好。样品加标回收率在98.92%~100.38%之间, 适用于铜冶炼烟尘中铜含量为5.00 %～65.00 %的测定。     

Determination of Phenols and Cresols in Urine by Gas Chromatography

Abstract

A rapid, simple, and sensitive method was developed for the determination of three cresol isomers and phenol in urine. The sample was spiked with m-chlorophenol, as internal standard, and hydrolyzed with sulfuric acid at ambient temperature. The hydrolyzed solution was saturated with ammonium sulfate and extracted with ethyl acetate. The extract was injected without derivatization into a gas chromatograph fitted with a flame ionization detector and a glass column packed with 0.1% SP 1000 on Carbopack C. All four analytes, which eluted within 13 minutes, were quantified from standard curves.

The method was evaluated by analysis of spiked urine pools from laboratory workers and samples of urine from workers in a coal gasification plant.     

Determination of salbutamol using on-line solid-phase extraction and sequential injection analysis. Comparison of chemiluminescence and fluorescence detection

Determination of salbutamol using sequential injection analysis (SIA) with chemiluminescence and fluorescence detection has been devised. The chemiluminescence signal was emitted during the oxidation of salbutamol by potassium permanganate in sulfuric acid medium. Sodium polyphosphate was used as chemiluminescence enhancer. The fluorescence signal (excitation wavelength 230 nm) was also measured in sulfuric acid medium. Both detection techniques were compared with respect to the application of the methods to the determination of salbutamol in biological materials. The sample pre-treatment takes place directly in the SIA system, when salbutamol is adsorbed on the solid-phase (Baker-carboxylic acid) microcolumn integrated into the system. Sulfuric acid serves both as the reagent and the eluent. The lab-made SIA system consisted of a 2.5-mL Cavro syringe pump, ten-port Vici Valco selection valve and Spectra-Physics FS 970 fluorescence detector, which was lab-modified for chemiluminescence detection. The system was controlled by a PC using originally compiled LabVIEW-supported software. Concentrations, volumes of reagents and flow rates were optimised by a simplex method. Salbutamol was determined in the linear range 0.05-10 microg mL(-1) (RSD 1.53%), with the detection limit (3 sigma) 0.03 microg mL(-1) and sample throughput of 42 samples per hour with chemiluminescence detection in standard solutions. The fluorescence detection enabled the determination of salbutamol in standard solutions in the linear range 0.5-100 microg mL(-1) (RSD 2.69%), with the detection limit 0.2 microg mL(-1) and sample throughput of 24 h(-1). The proposed methods were applied to the determination of salbutamol in human serum and urine. However, serum is a very complicated matrix and the SIA-SPE analysis did not provide satisfactory results. It was possible to determine salbutamol in human urine using this technique. Better recovery was achieved with fluorescence detection.     

Spectrofluorimetric determination of malic acid with β-naphthol

A detailed study of the spectrofluorimetric determination of malic acid by reaction with /gb-naphthol is reported. As little as 0.1 /smg of malic acid can be determined. The optimum concentration of sulfuric acid is 80% (v/v). The interferences of citric, succinic and tartaric acids are discussed.     

高效毛细管区带电泳测定人尿液中尿酸、肌酐和伪尿核苷的含量

报道了采用高效毛细管区带电泳技术直接将人尿液注入毛细管进行尿液中肌酐、尿酸及伪尿核苷含量测定的新方法。试验表明,以磷酸盐（ｐＨ６．１）作缓冲液,对人体尿液中肌酐、尿酸及伪尿核苷进行直接分析具有较高的灵敏度和较好的重复性。     

Spectrofluorimetric determination of moxifloxacin in tablets, human urine and serum

A spectrofluorimetric method to determine the antibiotic moxifloxacin is proposed and was applied to pharmaceuticals, human urine and serum. The fluorimetric method allows the determination of 30-300 ng mL-1 moxifloxacin in aqueous solution containing phosphoric acid-phosphate buffer (pH 8.3) with lambda exc = 287 nm and lambda em = 465 nm. Detection and quantification limits were 10 and 30 ng mL-1, respectively, with a relative standard deviation (n = 10) of 2%. This method was applied to the determination of moxifloxacin in three Spanish commercial pharmaceutical formulations. Another variant of the method in micellar medium allows the direct measurement of moxifloxacin in human serum and urine by standard additions. The enhanced fluorescence of moxifloxacin in 8 mM sodium dodecyl sulfate (SDS) solution at pH 4.0 (acetic acid-acetate buffer) for lambda exc = 294 nm and lambda em = 503 nm shows the same linear range as the aqueous method with a 25% lower slope (with detection and quantification limits of 15 and 60 ng mL-1, respectively, and a relative standard deviation of 1.3%), but permits the background fluorescence for urine and serum blanks to be minimized. Hence, sufficient sensitivity is reached to determine therapeutic concentrations of the drug in urine (average recovery 102 +/- 2%) and serum (average recovery 105 +/- 2%) samples.     

The determination of oxalic acid in urine by high performance liquid chromatography with electrochemical detection

A system for the determination of oxalic acid in human urine using ion exchange-ion pair, high performance liquid chromatography with electrochemical detection (HPLCEC) is described. Urine is acidified with HCl, and excess CaCl2 is added to precipitate oxalate ion. The precipitate is isolated, redissolved in dilute sulfuric acid, and separated on a strong cation exchange column using an acetic acid-solium acetate-tetrabutylammonium tetrafluoroborate mobile phase adjusted to pH 2.8. Using an electrochemical detector at 1.25 volts vs. the saturated calomel electrode (SCE), oxalic acid exhibits a linear dynamic range from 1 to 1000 mg/liter with a detection limit of 0.1 mg/liter. Quantitative data are obtained by the method of standard addition in the clinically significant range from 5 to 40 mg/liter. Percentage recovery for spiked urine samples was 97.8% with a relative standard deviation of 2.5%.     

顶空气相色谱法测定羧甲基壳聚糖中氯乙酸残留量

采用顶空气相色谱法间接测定了羧甲基壳聚糖中氯乙酸的残留量。样品(0.2g)于顶空瓶中超声溶解在水3mL中,加入甲醇2.5mL,硫酸1.5mL,在70℃水浴反应40min使之酯化。按顶空条件进样,用HP-INNOWAX毛细管色谱柱分离,氢火焰离子化检测器测定。分别选择15min和85℃作为样品在顶空瓶中的平衡时间和平衡温度。氯乙酸的质量在0.2～20mg范围内与其峰面积呈线性关系,方法的检出限(3S/N)为5.6mg·L-1。方法用于实样中氯乙酸的测定,用标准加入法做回收试验,测得回收率在90.0%～92.0%之间,测定值的相对标准偏差(n=5)在0.7%～0.9%之间。     

Extraction of fluoxetine from aquatic and urine samples using sodium dodecyl sulfate-coated iron oxide magnetic nanoparticles followed by spectrofluorimetric determination

A new method based on the combination of magnetic solid phase extraction (MSPE) and spectrofluorimetric determination was developed for isolation and preconcentration of fluoxetine form aquatic and biological samples using sodium dodecyl sulfate (SDS) coated Fe(3)O(4) nanoparticles (NPs) as a sorbent. The unique properties of Fe(3)O(4) NPs including high surface area and strong magnetism were utilized effectively in the MSPE process. Effect of different parameters influencing the extraction efficiency of fluoxetine including the amount of Fe(3)O(4) and SDS, pH value, sample volume, extraction time, desorption solvent and time were optimized. Under optimized condition, the method was successfully applied to the extraction of fluoxetine from water and urine samples and absolute recovery amount of 85%, detection limit of 20 μg L(-1) and a relative standard deviation (RSD) of 1.4% were obtained. The method linear response was over a range of 50-1000 μg L(-1) with R(2)=0.9968. The relative recovery in different aquatic and urine matrices were investigated and values of 80% to 104% were obtained. The whole procedure showed to be conveniently fast, efficient and economical for extraction of fluoxetine from environmental and biological samples.     

Factorial design and response surface optimization of spectrophotometric sequential injection analysis of olanzapine formulations

A new spectrophotometric sequential injection analysis (SIA) method for the assay of olanzapine in pharmaceutical formulations was optimized by the factorial design and the response surface approaches. The method was based on the oxidation of olanzapine by an excess amount of permanganate in sulfuric acid media. The reduction of permanganate was spectrophotometrically detected at 570 nm. The 2³ full factorial design was adopted for the optimization of permanganate concentration, sulfuric acid concentration and flow rate. The method was validated based on the IUPAC guidelines. Real pharmaceutical samples were subjected to the proposed SIA method and the results were in satisfactory agreement with those obtained by a previous spectrophotometric method. The full-automation of SIA empowered the proposed method with high repeatability (RSD 1.74%, n = 7) and intermediate-precision (RSD 2.53%, n = 5). Additionally, both automation and miniaturization offered high sampling frequency (26 samples/h). Furthermore, the employment of chemometric optimization enhanced sensitivity of the method with limits of detection and quantification of 1.07 and 3.57 mg/L, respectively. Comparing with previous olanzapine assay methods, which employing conventional analytical techniques, the new SIA method is inexpensive in terms of instrumentation, consumption of reagents and samples as well as effort and manpower. The SIA method is also safer for handling solutions and for the environment.