纳米SiO2与阳离子表面活性剂的相互作用及其诱导的正辛烷-水乳状液的双重相转变

研究了3种不同结构的水溶性阳离子表面活性剂对纳米二氧化硅颗粒的原位表面活性化作用, 它们分别是单头单尾的十六烷基三甲基溴化铵(CTAB)、单头双尾的双十二烷基二甲基溴化铵(di-C12DMAB)和双头双尾的Gemini型阳离子三亚甲基-二(十四酰氧乙基溴化铵)(II-14-3), 并通过测定Zeta电位、吸附等温线及接触角等参数对相关机理进行了阐述. 结果表明, 阳离子表面活性剂吸附到颗粒/水界面形成以疏水基朝向水的单分子层, 从而增强了颗粒表面的疏水性是原位表面活性化的基础. 通过吸附CTAB和II-14-3, 颗粒的疏水性适当增强, 能吸附到正辛烷/水界面稳定O/W(1)型乳状液; 而通过吸附di-C12DMAB所形成的单分子层更加致密, 颗粒的疏水性进一步增强, 进而使乳状液从O/W(1)型转变为W/O型; 当表面活性剂浓度较高时, 由于链-链相互作用, 表面活性剂分子将在颗粒/水界面形成双层吸附, 使颗粒表面变得亲水而失去活性, 但此时体系中游离表面活性剂的浓度已增加到足以单独稳定O/W(2)型乳状液的程度. 因此当采用纳米二氧化硅和di-C12DMAB的混合物作乳化剂时, 通过增加di-C12DMAB的浓度即可诱导乳状液发生O/W(1)→W/O→O/W(2)双重相转变.     

纳米SiO2/十二烷基氨基丙酸钠协同稳定的pH响应性Pickering乳状液

用纳米SiO₂颗粒与微量氨基酸型两性表面活性剂十二烷基氨基丙酸钠作复合乳化剂, 以正癸烷为油相, 制备了pH响应性O/W型Pickering乳状液. 室温下该乳状液在pH≤4.0 时稳定, 在pH≥6.0时不稳定, 因此, 可以通过改变水相的pH值使乳状液在稳定和破乳之间多次循环. 在酸性水介质中, 氨基酸型两性表面活性剂分子呈阳离子状态, 可通过静电作用吸附到带负电荷的SiO₂颗粒表面, 产生原位疏水化作用, 使其转变为表面活性颗粒; 而在中性和碱性水介质中, 氨基酸型两性表面活性剂呈两性或阴离子状态, 不能产生原位疏水化作用, 因而导致乳状液破乳. 相关作用机理通过吸附量、 Zeta电位及接触角等实验数据得以论证. 该刺激-响应性Pickering乳状液在乳液聚合、 油品输送以及燃料生产等领域具有重要的应用价值.     

Nanoparticle formation by monomer-starved semibatch emulsion polymerization

Latexes with very small particle size are usually manufactured by microemulsion polymerization. This article explains the preparation of nanolatexes by monomer-starved nucleation in a conventional semibatch emulsion polymerization with a low surfactant/monomer ratio and with no need for a cosurfactant. The semibatch emulsion polymerization reactions started with an aqueous solution of a surfactant and a water soluble initiator. Monomer was added at a fixed rate. The size of particles decreased with decreasing rate of monomer addition. High solids content nanolatexes with particles as small as 25 nm in diameter were produced. Several monomers with different water solubilities were compared. The order of the number of particles in terms of the rate of monomer addition was found to depend on the type of monomer. Water soluble monomers produced more particles due to associated chain transfer to monomer and radical exit. The monodispersity of particles at the end of nucleation increased as the rate of monomer addition decreased. The technique seems to be preferable to microemulsion polymerization, which uses a high concentration of surfactant/cosurfactant and is limited to low monomer holdup.     

Synthesis of core-shell polystyrene nanoparticles by surfactant free emulsion polymerization using macro-RAFT agent

Novel approach for the synthesis of core-shell polystyrene nanoparticles by living hydrophilic polymer consisting of thiocarbonyl thio end group is reported. The surfactant free emulsion polymerization of styrene in the presence of macro-RAFT (reversible addition fragmentation chain transfer) agent is carried out to synthesize stable latex particles with smaller particle size. A macro-RAFT agent is prepared by homopolymerization of sodium styrene sulfonate (NaSS) in aqueous phase by using dithioester as chain transfer agent. This synthesized polystyrene sulfonate-sodium (PSS-Na) based macro-RAFT agent, which is essentially water soluble macromolecular chain transfer agent used for the surfactant-free batch emulsion polymerization of styrene. Transmission electron microscopy (TEM) study of the synthesized colloids shows the narrow particle size distribution with core-shell morphology.     

Size-Controlled Synthesis of Nano-Zeolites and Their Application to Light Olefin Synthesis

For the application of zeolites as heterogeneous catalysts, low diffusion resistance for hydrocarbons within the micropore is essential for improving product selectivity and catalyst lifetime. This problem has been overcome by reducing the crystal size. This review introduces size-controlled preparation of nano-sized zeolites via hydrothermal synthesis in water/surfactant/organic solvent (emulsion method) and their application to heterogeneous catalysts. The ionicity of the hydrophilic group in surfactant molecules and the concentration of the Si source affected the crystallinity and morphology of zeolites prepared using the emulsion method. When using a non-ionic surfactant, mono-dispersed silicalite-1 nanocrystals ~60?nm in diameter were successfully prepared. Nano- and macro-ZSM-5 zeolites with crystal sizes of ~150?C200?nm and 1.5???m, respectively, were prepared and applied to n-hexane cracking and acetone-to-olefin reactions to investigate the effect of zeolite crystal size on catalytic stability and light olefin yield. Application of nano-zeolite to light olefin production was effective in achieving faster mass transfer of hydrocarbon molecules within the micropore, which led to improvements in olefin yields and catalyst lifetime.     

Reversible addition–fragmentation chain transfer polymerization of methyl methacrylate in emulsion

Theoretical simulations showed that for controlled/living radical polymerization in an emulsion system, some of the earliest born particles could be superswollen to a size close to 1 μm. We hypothesized that the superswelling of these particles would lead to colloidal instability. Under the guidance of the simulation results, reversible addition–fragmentation chain transfer (RAFT) emulsion polymerization of methyl methacrylate (MMA) was carried out. Experimental results showed that increasing the initiation rate, surfactant level, and targeted molecular weight could improve the colloidal stability of the RAFT polymerization of MMA in an emulsion. The experimental results were in full accord with the theoretical predictions. The poor control of the molecular weight and polydispersity index was found to have a close relationship with the colloidal instability. For the first time, we demonstrated that RAFT polymerization could successfully be implemented with little coagulum, good control of the molecular weight, and a low polydispersity index with the same process used for traditional emulsion polymerization but with higher surfactant levels and initiation rates. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44:2837–2847, 2006     

Growth, stability, optical and photoluminescent properties of aqueous colloidal ZnS nanoparticles in relation to surfactant molecular structure

The interaction between organic molecules and the surface of nanoparticles (NPs) strongly affects the size, properties and applications of surface-modified metal sulfide semiconductor nanocrystals. From this viewpoint, we compared the influence of cationic surfactants with various chain lengths and anionic surfactants with different head groups, as surface modifiers during synthesis of ZnS NPs in aqueous medium. The surfactant adsorbs on the surface of the particles as micelle-like aggregates. These aggregates can form even at the concentration lower than critical micelle concentration (cmc) due to interaction between the polar groups and the NPs. The nature of interaction depends specifically on the surfactant polar group. The ability of surfactant to form the micelle-like aggregates on the surface of the NPs correlates with their cmc. This leads to the fact that the surfactant with longer tail stabilizes the NPs better since its cmc is lower. The adsorption of the surfactant on the NPs also stabilizes them by the change of their charge which is in accordance with the correlation of zeta potential with the particles stability. The energetics of surface states generating interesting photoluminescence (PL) properties in ZnS NPs has been governed by the nature of surfactant molecules. In general, the size, structure, and stability of the ZnS NPs can be controlled by the choice of suitable surfactant.     

Synergistic stabilization of emulsions by a mixture of surface-active nanoparticles and surfactant

The stability and rheology of tricaprylin oil-in-water emulsions containing a mixture of surface-active hydrophilic silica nanoparticles and pure nonionic surfactant molecules are reported and compared with those of emulsions stabilized by each emulsifier alone. The importance of the preparation protocol is highlighted. Addition of particles to a surfactant-stabilized emulsion results in the appearance of a small population of large drops due to coalescence, possibly by bridging of adsorbed particles. Addition of surfactant to a particle-stabilized emulsion surprisingly led to increased coalescence too, although the resistance to creaming increased mainly due to an increase in viscosity. Simultaneous emulsification of particles and surfactant led to synergistic stabilization at intermediate concentrations of surfactant; emulsions completely stable to both creaming and coalescence exist at low overall emulsifier concentration. Using the adsorption isotherm of surfactant on particles and the viscosity and optical density of aqueous particle dispersions, we show that the most stable emulsions are formed from dispersions of flocculated, partially hydrophobic particles. From equilibrium contact angle and oil-water interfacial tension measurements, the calculated free energy of adsorption E of a silica particle to the oil-water interface passes through a maximum with respect to surfactant concentration, in line with the emulsion stability optimum. This results from a competition between the influence of particle hydrophobicity and interfacial tension on the magnitude of E.     

Detection of protein conformational change by optical second-harmonic generation

An ability to detect and track conformational change in real time is essential to understanding the dynamic relationship between structure and function in biological molecules. Here I show that second-harmonic generation (SHG), a surface-selective technique, offers a new means to probe structural dynamics. A protein, calmodulin, was labeled with a second-harmonic-active dye and immobilized to a surface. Although neither the labeling nor the immobilization was done in a site-specific manner, an overall net orientation of the labels was produced relative to the surface plane. Conformational change of the protein induced by calcium alters the average tilt angle of the labels and causes a change in the intensity of second-harmonic radiation generated by the surface. As SHG is spatially and temporally coherent and depends quantitatively on the structural details of a surface, the method described here should serve as the starting point for more detailed studies of the mechanism of conformational change in molecules, as well as related topics such as protein folding. SHG's surface selectivity also suggests its use in a range of biological applications which require detection of surface-bound molecules.     

Development of an ab initio emulsion atom transfer radical polymerization: from microemulsion to emulsion

Atom transfer radical polymerization (ATRP) has been successfully extended to an ab initio emulsion system using a "two-step" procedure, in which the final emulsion polymerization system was formed by adding monomer to an ongoing microemulsion ATRP. The newly developed AGET (activators generated by electron transfer) initiation technique was employed in the first stage of this ab initio ATRP. It allows using oxidatively stable Cu(II) species that is reduced in situ by ascorbic acid. The surfactant concentration in the final emulsion system was efficiently decreased to approximately 2 wt % (approximately 10 wt % vs monomer) by decreasing the catalyst concentration and changing the ratio of the monomer added at the microemulsion stage to the monomer added during the second stage. This two-step procedure avoids the necessity of transporting catalysts through the aqueous media during polymerization, resulting in a controlled emulsion polymerization, as evidenced by a linear first-order kinetic plot and formation of a polymer with a relatively narrow molecular weight distribution (Mw/Mn = 1.2-1.4). The polymerization typically reached 70-90% monomer conversion in 5-6 h. The resulting polymer had high chain-end functionality and was successfully chain extended to form in situ block copolymers by adding the second monomer to an ongoing emulsion polymerization. The stable latex from the ab initio emulsion ATRP had a particle size approximately 120 +/- 10 nm.     

A novel formulation of the pickering emulsion stabilized with silica nanoparticles and its thermal resistance at high temperatures

Stabilization of emulsions with solid particles can be used in several fields of oil and gas industry because of their higher stability. Solid particles should be amphiphilic to be able to make Pickering emulsions. This goal is achieved by using surfactants at low concentrations. Oil-in-water (o/w) emulsions are usually stabilized by surfactant but show poor thermal stability. This problem limits their applications at high-temperature conditions. In this study, a novel formulation for o/w stabilized emulsion by using silica nanoparticles and the nonionic surfactant is investigated for the formulation of thermally stable Pickering emulsion. The experiments performed on this Pickering emulsion formula showed higher thermal stability than conventional emulsions. The optimum wettability was found for DME surfactant and silica nanoparticles, consequently, in that region; Pickering emulsion showed the highest stability. Rheological changes were evaluated versus variation in surfactant concentration, silica concentration and pH. Scanning electron microscopy images approved the existence of a rigid layer of nanoparticle at the oil-water interface. Finally, the results show this type of emulsion remains stable in harsh conditions and allows the system to reach its optimum rheology without adding any further additives.     

High-contrast and real-time visualization of membrane proteins in live cells with malachite green-based fluorogenic probes

Imaging dynamics of membrane proteins of live cells in a wash-free and real-time manner has been a challenging task. Herein, we report unprecedented applications of malachite green(MG), an organic dye widely used in pigment industry, as a switchable fluorophore to monitor membrane enzymes or noncatalytic proteins in live cells. Conformationally flexible MG is non-fluorescent in aqueous solution, yet covalent binding with endogenous proteins of cells significantly enhances its fluorescence at 670...     

Preparation of a xanthate‐terminated dextran by click chemistry: Application to the synthesis of polysaccharide‐coated nanoparticles via surfactant‐free ab initio emulsion polymerization of vinyl acetate

Stable monodisperse poly(vinyl acetate) (PVAc) submicronic latex particles were synthesized by ab initio batch emulsion polymerization using a dextran derivative from renewable resource as an efficient steric stabilizer. The dextranend‐functionalized by a xanthate moiety was synthesized by Huisgen's 1,3‐dipolar cycloaddition (click chemistry). It was applied as a macromolecular RAFT (reversible addition fragmentation chain transfer) agent in surfactant‐free emulsion polymerization of vinyl acetate to form in situ an amphiphilic block copolymer able to efficiently stabilize the latex particles. The method afforded the preparation of high solids content (27%) latices coated by dextran. Both the kinetic study and the molar mass analyses confirmed the involvement of the dithiocarbonate group in the emulsion polymerization process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2845–2857, 2008     

利用光化学探针技术研究长链烷烃硫酸钠水溶液中预胶束的生成

罗丹明6G与罗丹明B之间的能量转移和吖啶橙形成聚态的现象用于研究长链烷基硫酸钠(C~nH~2~n~+~1OSO~3Na,n=12,14和16)在水溶液中预胶束的生成。结果表明,烷基链的长度影响这些表面活性剂形成预胶束的能力,碳数的增加使预胶束形成浓度降低。     

Effect of homologous series of alkyl sulfate surfactants on the emulsion polymerization of styrene. I. Equal total concentrations

There is evidence in the literature that the rates of emulsion polymerization increase by a large factor as the alkyl chain length increases for a homologous series of surfactants. However, the area occupied by a surfactant molecule in a saturated monolayer at the polystryene/water interface is independent of chain length for alkyl sulfates so that, on the basis of Gardon's theory, equal rates of polymerization would be expected when equal concentrations of surfactants are used. There is a large increase in the number of polymer latex particles formed and in the rate of emulsion polymerization as the surfactant concentration is increased through the critical micelle concentration; this accounts for the large increases reported, because the lower members of the homologous series are below their critical micelle concentrations in most of the published studies. When a common concentration is chosen that is above the critical micelle concentration even for the lowest member of the series, only a relatively small increase in latex particle number and rate of emulsion polymerization with alkyl chain length of the surfactant is observed. This is attributable to an increase in the concentration of surfactant micelles. Good agreement with Gardon's theory is obtained when the concentration of micellar surfactant is used instead of the total surfactant concentration.     

Double phase inversion of emulsions containing layered double hydroxide particles induced by adsorption of sodium dodecyl sulfate

A liquid paraffin-water emulsion was investigated using layered double hydroxide (LDH) particles and sodium dodecyl sulfate (SDS) as emulsifiers. Both emulsifiers are well-known to stabilize oil-in-water (o/w) emulsions. Surprisingly, a double phase inversion of the emulsion containing LDH particles is induced by the adsorption of SDS. At a constant LDH concentration, the emulsion is o/w type when SDS concentrations are low. At intermediate SDS concentrations, the first emulsion inversion from o/w to w/o occurs, which is attributed to the enhanced hydrophobicity of LDH particles caused by the desorption of the second layer of surfactant, leaving a densely packed SDS monolayer on the LDH exterior surfaces. The second inversion from water-in-oil (w/o) to o/w occurs at higher SDS concentrations, which may be due to the competitive adsorption at the oil/water interfaces between the LDH particles modified by the SDS bilayers and the free SDS molecules in the bulk solution, but the free SDS molecules dominate and determine the emulsion type. Laser-induced fluorescent confocal micrographs clearly confirm the adsorption of LDH particles on the surfaces of the initial o/w and intermediate w/o emulsion droplets, whereas no LDH particles were adsorbed on the final o/w emulsion droplet surfaces. Also, transmission electron microscopy (TEM) observations indicate that the shape of the final o/w emulsions is similar to that of the monomeric SDS-stabilized emulsion but different from that of the initial o/w emulsions. The adsorption behavior of SDS on LDH particles in water was investigated to offer an explanation for the emulsion double phase inversion. The zeta potential results show that the particles will flocculate first and then redisperse following surfactant addition. Also, X-ray diffraction (XRD) measurements indicate that SDS adsorption on the LDH interior surfaces will be complete at intermediate concentrations.     

Properties of the amphiphilic films in mixed cationic/anionic vesicles: a comprehensive view from a literature analysis

The so-called 'catanionic' vesicles are made from mixtures of cationic and anionic surfactants. They are attracting much interest because they form spontaneously and they can be obtained from a variety of surfactants, either commercially available or issued from original synthesis. A distinction can be made between the properties of simple surfactant mixtures and of ion pair amphiphiles (IPA), in which the counterions have been removed. We have drawn up in this paper, an inventory of the different vesicular systems which have been described in the literature, insisting on the specific features associated with these two categories of systems. We have collected here especially, information concerning the phase behaviors, the microscopic composition of the vesicular particles, their structural and size determinations, the dynamic aspects (including the micelle-vesicle transition), the theoretical predictions from thermodynamic models and the entrapment of probe molecules. We discuss the potential of catanionic vesicles as delivery systems and we show that a full understanding of their entrapment/release properties will call for much more experimental work with well defined protocols. We also point out some unsolved questions concerning the role of the excess surfactant in the stabilization of the particles and the conditions required to obtain a favourable curvature of the surfactant film.     

The effect of Co(II)‐mediated catalytic chain transfer on the emulsion polymerization kinetics of methyl methacrylate

The effect the catalytic chain transfer agent, bis[(difluoroboryl) dimethylglyoximato] cobalt(II) (COBF), on the course of the ab initio emulsion polymerization of methyl methacrylate, and the product properties in terms of the molecular weight distribution were investigated. The emulsion polymerization kinetics have been studied with varying surfactant, initiator, and COBF concentrations. The experimentally determined average number of radicals per particle strongly depends on the concentration of COBF and proves to be in good agreement with the results of model calculations. The apparent chain transfer constant, determined up to high conversion, is in excellent agreement with the predicted value based on a mathematical model based on COBF partitioning and the Mayo equation. The results of this work enhance the fundamental understanding of the influence a catalytic chain transfer agent has on the course of the emulsion polymerization and the control of the molecular weight distribution. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5078–5089, 2009     

Droplet Formation Study in Emulsification Process by KSM using a Novel In Situ Visualization System

The semi real-time observations of oil-in-water emulsification process in a Kenics static mixer were performed using a novel in situ visualization system. The homogenization processes and emulsion characteristics were analyzed using images taken periodically in fixed time intervals during the emulsification process. Morphological evolution of droplets was monitored and the mechanism of droplet formation was studied, both experimentally and theoretically. A wide range of dispersed phase concentration as well as surfactant concentration were used in the experiments and their impacts on emulsion characteristics were determined. Different droplet formation mechanisms occurred during the experimental results are presented. The relationship between droplet sizes, flow rate, surfactant concentration, and other impact factors was visually shown, and their role in controlling the emulsification process was revealed. The minimum droplet size obtained from the dispersed phase in emulsions was shown to be perfectly monitored and controlled by this technique.     

Ab Initio Emulsion Atom‐Transfer Radical Polymerization

Stable latexes of poly(meth)acrylates with predetermined molecular weights, narrow molecular‐weight distributions, and controlled architecture were prepared by true ab initio emulsion atom‐transfer radical polymerization. Water‐soluble (macro)initiators in combination with a hydrophilic catalyst, Cu/tris(2‐pyridylmethyl)amine, initiated the polymerization in the aqueous phase. The catalyst strongly interacted with the surfactant sodium dodecyl sulfate (SDS), thereby tuning the polymerization within nucleated hydrophobic polymer particles. Long‐term stable latexes were obtained, even with SDS loading below 3 wt % relative to monomer. Block and gradient copolymers were prepared in situ. The reaction volume and solid content were successfully increased to 100 mL and 40 vol %, respectively, thus suggesting facile scale‐up of this technique. The proposed setup could be integrated in existing industrial plants used for emulsion polymerization.