壁面马赫数分布规律可控的新型内收缩基准流场设计方法

根据有旋特征线理论,设计出了沿程马赫数下降规律可控的轴对称基准流场,分析了基准流场的几何参数(前缘压缩角及中心体半径)的影响规律,发现选取较小的前缘压缩角和中心体半径有利于得到性能优良的基准流场;然后在设计状态Ma=6时研究了三种典型的马赫数下降规律对这种轴对称流场性能的影响。最后考虑了粘性的影响,并进行了粘性修正探索,结果表明,采用附面层位移厚度修正方法后,基准流场的壁面压力分布和无粘情况吻合良好。      

On the effectiveness of viscous dissipation and Joule heating on steady Magnetohydrodynamic heat and mass transfer flow over an inclined radiate isothermal permeable surface in the presence of thermophoresis

The combined effect of viscous dissipation and joule heating on steady Magnetohydrodynamic heat and mass transfer flow of viscous incompressible fluid over an inclined radiate isothermal permeable surface in the presence of thermophoresis is studied. Numerical results for the dimensionless velocity, temperature and concentration profiles as well as the local skin-friction coefficient, the local Nusselt number and the local Stanton number are displayed graphically for various physical parameters. Comparisons with previously published work are performed and the results are found to be in very good agreement. Results show that rate of heat transfer is sensitive for increasing angle of inclination parameter for the case of fluid injection and it decreases with the increase of magnetic field parameter and Eckert number.     

Influence of surface mass transfer on mixed convection flows over non-isothermal horizontal flat plates

Non-similar solution of a steady mixed convection flow over a horizontal flat plate in the presence of surface mass transfer (suction or injection) is obtained when there is power-law variation in surface temperature. The surface temperature is assumed to vary as a power of the axial coordinate measured from the leading edge of the plate. A non-similar mixed convection parameter is considered which covers the whole convection regime, namely from pure free convection to pure forced convection. Numerical results are reported here to account the effects of Prandtl number, surface temperature, surface mass transfer parameter (suction or injection) on velocity and temperature profiles, and skin friction and heat transfer coefficients.     

Similarity solution of boundary layer stagnation-point flow towards a heated porous stretching sheet saturated with a nanofluid with heat absorption/generation and suction/blowing: A Lie group analysis

In this paper, heat and mass transfer analysis for boundary layer stagnation-point flow over a stretching sheet in a porous medium saturated by a nanofluid with internal heat generation/absorption and suction/blowing is investigated. The governing partial differential equation and auxiliary conditions are converted to ordinary differential equations with the corresponding auxiliary conditions via Lie group analysis. The boundary layer temperature, concentration and nanoparticle volume fraction profiles are then determined numerically. The influences of various relevant parameters, namely, thermophoresis parameter Nt, Brownian motion parameter Nb, Lewis number Le, suction/injection parameter S, permeability parameter k₁, source/sink parameter λ and Prandtl parameter Pr on temperature and concentration as well as wall heat flux and wall mass flux are discussed. Comparison with published results is presented.     

Effects of thermophoresis on hydromagnetic mixed convection and mass transfer flow past a vertical permeable plate with variable suction and thermal radiation

The present paper deals with the effect of surface mass transfer on MHD mixed convection flow past a heated vertical flat permeable surface in the presence of thermophoresis, radiative heat flux and heat source/sink. Usual similarity transformations are introduced to obtain similarity solution, using regular perturbation technique. To observe physical insight and interesting aspects of the problem in the presence of thermophoresis, the non-dimensional velocity, temperature and concentration field are numerically studied and displayed graphically for pertinent parameters. It is observed that the thermophoresis has dominant effect on mass transfer mechanism in particle deposition process. The model finds applications in studying particulate deposition on turbine blades, removing small particles from gas streams and determining chemical vapor deposition rate in chemical industries.     

Similarity solution in MHD: Effects of thermal diffusion and diffusion thermo on free convective heat and mass transfer over a stretching surface considering suction or injection

An analysis is carried out to study free convective heat and mass transfer of an incompressible, electrically conducting fluid over a stretching sheet in the presence of suction and injection with thermal-diffusion (Soret) and diffusion-thermo (Dufour) effects. The similarity solutions are obtained using scaling transformations. Furthermore, the similarity equations are solved numerically by using shooting technique with fourth-order Runge–Kutta integration scheme. A comparison with previously published work is performed and the results are found to be in good agreement. Numerical results of the local skin friction coefficient, the local Nusselt number and the local Sherwood number as well as the velocity, the temperature and the concentration profiles are presented for different physical parameters. The result indicates: (i) for fluids with medium molecular weight (H₂, air), Dufour and Soret effects should not be neglected; and (ii) the suction and injection parameter has significant impact in controlling the rate of heat transfer in the boundary layer.     

Effect of suction/injection on free convection along a vertical plate in a nanofluid saturated non-Darcy porous medium with internal heat generation

The effect of internal heat generation on free convection along a vertical plate embedded in a nanofluid saturated non-Darcy porous medium in the presence of suction/injection is analyzed. The non-linear governing equations and their associated boundary conditions are initially cast into dimensionless forms by non-dimensional variables. The resulting equations are solved numerically by an accurate, implicit, iterative finite-difference methodology and the obtained results are compared favorably with previously published work. A parametric study is performed to illustrate influence of the temperature exponent, non-Darcy, suction/injection, Brownian motion and thermophoresis parameters on the profiles of the velocity components, temperature and nanoparticle volume fraction. The numerical data for the heat and nanoparticle mass transfer rates have been tabulated for various parametric conditions.     

粘性导电流体在磁场作用下流过多孔通道时传热传质振荡流的数值解——用于病理状态动脉中血液的流动

当血管内壁出现多孔性结构时,流过多孔性血管的血液将作不稳定的MHD流动.研究血液在其中的传热传质问题,考虑了与时间相关的渗透率和振荡引起的吸入速度,并数值地求解该问题.对分析中出现的参数取不同数值时,图形给出了速度、温度、浓度场,以及表面摩擦因数、Nusselt数和Sherwood数的计算结果.研究表明,血液流动受磁场和Grashof数的影响明显.     

Dual solutions in mixed convection boundary-layer flow with suction or injection

The effect of suction/injection on the laminar mixed convectionboundary-layer flow about a vertical wall in an incompressibleviscous fluid is considered. The similarity solutions are obtainedfor some values of the suction/injection parameter as well asthe mixed convection parameter for three particular cases: uniformtemperature, uniform heat flux and stagnation flow. The resultingsystem of non-linear ordinary differential equations is solvednumerically for both assisting and opposing flow regimes usinga finite-difference scheme known as the Keller box method. Numericalresults are obtained for the skin friction coefficient and localNusselt number as well as velocity and temperature profiles.The effects of the involved parameters on the skin frictioncoefficient and the local Nusselt number characteristics arediscussed. It is found that dual solutions exist for assistingflow, besides that usually reported in the literature for opposingflow.     

Uniform suction/blowing effect on flow and heat transfer due to a stretching cylinder

The present paper presents a numerical solution of flow and heat transfer outside a stretching permeable cylinder. The governing system of partial differential equations is converted to ordinary differential equations by using similarity transformations, which are then solved numerically using the Keller-box method. The main purpose of the present study is to investigate the effects of the governing parameters, namely the suction/injection parameter, Prandtl number, and Reynolds number on the velocity and temperature profiles as well as the skin friction coefficient and the Nusselt number. The results are shown graphically. The values of the skin friction coefficient and the Nusselt number are presented in tables.     

Laminar compressible boundary layer flow at a three-dimensional stagnation point with vectored mass transfer

The effect of surface mass transfer velocities having normal, principal and transverse direction components (‘vectored’ suction and injection) on the steady, laminar, compressible boundary layer at a three-dimensional stagnation point has been investigated both for nodal and saddle points of attachment. The similarity solutions of the boundary layer equations were obtained numerically by the method of parametric differentiation. The principal and transverse direction surface mass transfer velocities significantly affect the skin friction (both in the principal and transverse directions) and the heat transfer. Also the inadequacy of assuming a linear viscosity-temperature relation at low-wall temperatures is shown.     

Approximate analytical solution for MHD stagnation-point flow in porous media

In this paper, the steady two-dimensional laminar forced MHD Hiemenz flow against a flat plate with variable wall temperature in a porous medium which was solved numerically using the implicit finite-difference of Keller-box method [Yih KA. The effect of uniform suction/blowing on heat transfer of magnetohydrodynamic Hiemenz flow through porous media. Acta Mech 1998;130:147–58] is revisited. A simple analytic approach of the Adomian decomposition method (ADM) is employed to obtain an approximate analytical solution of the problem. The skin friction coefficient and the rate of heat transfer given by the ADM are in good agreement with the numerical solutions of the Keller-box method.     

The study of Heat and Mass Transfer in a Visco elastic fluid due to a continuous stretching surface using Homotopy Analysis Method

In this paper, an approximate analytical solution is derived for the flow velocity and temperature due to the laminar, two-dimensional flow of non-Newtonian incompressible visco elastic fluid due to a continuous stretching surface. The surface is stretched with a velocity proportional to the distance $x$ along the surface. The surface is assumed to have either power-law heat flux or power-law temperature distribution. The presence of source/sink and the effect of uniform suction and injection on the flow are considered for analysis. An approximate analytical solution has been obtained using Homotopy Analysis Method(HAM) for various values of visco elastic parameter, suction and injection rates. Optimal values of the convergence control parameters are computed for the flow variables. It was found that the computational time required for averaged residual error calculation is very very small compared to the computation time of exact squared residual errors. The effect of mass transfer parameter, visco elastic parameter, source/sink parameter and the power law index on flow variables such as velocity, temperature profiles, shear stress, heat and mass transfer rates are discussed.     

Heat and mass transfer in MHD free convection from a moving permeable vertical surface by a perturbation technique

Numerical results are presented for heat and mass transfer effect on hydromagnetic flow of a moving permeable vertical surface. An analysis is performed to study the momentum, heat and mass transfer characteristics of MHD natural convection flow over a moving permeable surface. The surface is maintained at linear temperature and concentration variations. The non-linear coupled boundary layer equations were transformed and the resulting ordinary differential equations were solved by perturbation technique [Aziz A, Na TY. Perturbation methods in heat transfer. Berlin: Springer-Verlag; 1984. p. 1–184; Kennet Cramer R, Shih-I Pai. Magneto fluid dynamics for engineers and applied physicists 1973;166–7]. The solution is found to be dependent on several governing parameter, including the magnetic field strength parameter, Prandtl number, Schmidt number, buoyancy ratio and suction/blowing parameter, a parametric study of all the governing parameters is carried out and representative results are illustrated to reveal a typical tendency of the solutions. Numerical results for the dimensionless velocity profiles, the temperature profiles, the concentration profiles, the local friction coefficient and the local Nusselt number are presented for various combinations of parameters.     

Numerical study of viscous dissipation effect on free convection heat and mass transfer of MHD non-Newtonian fluid flow through a porous medium

The problem of free convection heat with mass transfer for MHD non-Newtonian Eyring–Powell flow through a porous medium, over an infinite vertical plate is studied. Taking into account the effects of both viscous dissipation and heat source. The temperature and concentration are of periodic variation. The governing non-linear partial differential equations of this phenomenon are transformed into non-linear algebraic system utilizing finite difference method. Numerical results for the velocity, temperature and concentration distributions as well as the skin friction, heat and mass transfer are obtained and reported in tabular form and graphically for different values of physical parameters of the problem. Also, the stability condition is studied.     

MHD mixed convection of a viscous dissipating fluid about a permeable vertical flat plate

The problem of steady laminar magnetohydrodynamic (MHD) mixed convection heat transfer about a vertical plate is studied numerically, taking into account the effects of Ohmic heating and viscous dissipation. A uniform magnetic field is applied perpendicular to the plate. The resulting governing equations are transformed into the non-similar boundary layer equations and solved using the Keller box method. Both the aiding-buoyancy mode and the opposing-buoyancy mode of the mixed convection are examined. The velocity and temperature profiles as well as the local skin friction and local heat transfer parameters are determined for different values of the governing parameters, mainly the magnetic parameter, the Richardson number, the Eckert number and the suction/injection parameter, f_w. For some specific values of the governing parameters, the results agree very well with those available in the literature. Generally, it is determined that the local skin friction coefficient and the local heat transfer coefficient increase owing to suction of fluid, increasing the Richardson number, Ri (i.e. the mixed convection parameter) or decreasing the Eckert number. This trend reverses for blowing of fluid and decreasing the Richardson number or decreasing the Eckert number. It is disclosed that the value of Ri determines the effect of the magnetic parameter on the momentum and heat transfer.     

Numerical simulation for natural convection of micropolar fluids flow along slender hollow circular cylinder with wall conduction effect

This paper presents a numerical analysis of the flow and heat transfer characteristics of natural convection in a micropolar fluid flowing along a vertical slender hollow circular cylinder with conduction effects. The nonlinear formulation governing equations and their associated boundary conditions are first cast into dimensionless forms by a local non-similar transformation. The resulting equations are then solved using the cubic spline collocation method and the finite difference scheme. This study investigates the effects of the conjugate heat transfer parameter, the micropolar parameter, and the Prandtl number on the flow and the thermal fields. The conjugate heat transfer parameter reduces the solid–liquid interfacial temperature, the skin friction factor and the local heat transfer rate. The effect of wall conduction on the local heat transfer rate, interfacial temperature and skin friction factor is found to be more pronounced in a system with a greater Prandtl number. Moreover, the current results are comparing with Newtonian fluid to obtain the important results of the heat transfer and flow characteristics on micropolar fluids. It shows that an increase in the interfacial temperature, a reduction in the skin friction factor, and a reduction in the local heat transfer rate are identified in the current micropolar fluid case.     

Convective flows of micropolar fluids from radiate isothermal porous surfaces with viscous dissipation and Joule heating

In this study, the steady laminar free-forced convective flow and heat transfer of micropolar fluids past a vertical radiate isothermal permeable surface with viscous dissipation and Joule heating is investigated numerically. The local similarity solutions for the flow, microrotation (angular velocity) and heat transfer characteristics are illustrated graphically for various material parameters. The effects of the pertinent parameters on the local skin friction coefficient, plate couple stress and the rate of heat transfer are also calculated. It was shown that micropolar fluids presented lower viscous drag and heat transfer values than those of the Newtonian fluids. The effect of radiation on the rate of heat transfer in a weakly concentrated micropolar fluid is higher than a strongly concentrated micropolar fluid. Results also show that full radiation has significant effect on the rate of heat transfer compared to the linear radiation.     

Mixed convection boundary layer flow over a permeable vertical surface with prescribed wall heat flux

The effects of suction/injection on the laminar mixed convection boundary-layer flow on a vertical wall with a prescribed heat flux are considered. The conditions which allow the equations to be reduced to similarity form are derived and numerical solutions of the resulting equations are obtained for a range of values of the suction/injection and buoyancy parameters. Two specific cases, corresponding to a stagnation point flow and uniform wall heat flux, are treated in detail. Results are presented in terms of the skin friction and wall temperature with a selection of velocity and temperature profiles also being given. Dual solutions are found to exist for assisting flow, these are an addition to what has been reported previously for opposing flows. Solutions for some limiting values of the parameters are also derived.     

Heat transfer in a visco-elastic fluid past a stretching sheet with viscous dissipation and internal heat generation

This paper deals with the study of heat transfer characteristics in the laminar boundary layer flow of a visco-elastic fluid over a linearly stretching continuous surface with variable wall temperature subjected to suction or blowing. The study considers the effects of frictional heating (viscous dissipation) and internal heat generation or absorption. An analysis has been carried out for two different cases of heating processes namely: (i) Prescribed surface temperature (PST) and (ii) Prescribed wall heat flux (PHF) to get the effect of visco-elastic parameter for various situations. Further increase of visco-elastic parameter is to decrease the skin friction on the sheet. The solutions for the temperature and the heat transfer characteristics are obtained in terms of Kummers function. Received: June 16, 2004; revised: February 8, 2005