Synthesis of inherently dissymmetric polyamides,

The preparation of polyamides from derivatives of optically active biphenic acid is described. The diacid chlorides chosen were 2,2′-dinitro-6,6′-dimethylbiphenyl-4,4′-dicarbonyl chloride and 2,2′-dichloro-6,6′-dimethylbiphenyl-4,4′-dicarbonyl chloride, the diamines were phenyldiamines (o-, m-, p-) piperazine, trans-2,5-dimethylpiperazine, and 1,2-piperaazolidine. Polymerization was carried out by the method of interfacial polycondensation. The polymers of aromatic diamines were insoluble in common organic solvents but soluble in dimethylformamide containing 5% lithium chloride, triesters of phosphoric acid, and methanesulfonic acid. The polymers of aliphatic diamines were also insoluble in common organic solvents but soluble in trifluoroethanol. All polymers had melting points higher than 280°C.     

Conformational properties of structurally rigid polyamides. I. Conformation of polyamides and model diamides derived from optically active cyclic 1,2-dicarboxylic acids

The conformational equilibria of piperidine diamides derived from five cyclic 1,2-dicarboxylic acids (I–V) have been investigated by dipole moment measurements and a priori conformational energy estimates. Since these diamides represent the building blocks of the polyamides derived from the above cyclic diacids and piperazine or trans-2,5-dimethylpiperazine, the results obtained in the study of the models have been used to investigate the conformation of the polymers. The overall evidence suggests that cyclopentane, cyclohexane, and bicyclooctane piperazine polymers behave as rigid rods in which the structural units possess approximately the same conformational preference exhibited by the respective model diamides.     

Conformational properties of structurally rigid polyamides. II. Effect of strong acids on the circular dichroism spectra of asymmetric polyamides with varying degree of structural rigidity

We have investigated the effect of methanesulfonic acid (MSA) on the circular dichroism (CD) spectra of some stereoregular polyamides derived from three cyclic 1,2-dicarboxylic acids (I–III) and piperazine (PIP), trans-2,5-dimethylpiperazine (DMPIP), or N,N′-dimethylethylenediamine (DMED). On the basis of a detailed knowledge of the conformational properties of these polymers, we have attempted an essentially empirical interpretation of the CD spectra and of their relative changes. A striking dependence of the optical properties from the conformational properties and/or transitions in the polymers has been found. Although far from suggesting a 1:1 correspondence between CD spectra and conformational changes, we wish to stress their general correspondence.     

Optical properties and conformations of asymmetric polyamides derived from optically active trans-1,2-cyclopropanedicarboxylic acid

Optical properties and conformations, in solution, of optically active polyamides derived from (+)(S)-trans-1,2-cyclopropanedicarboxylic acid with secondary diamines such as trans-2,5-dimethylpiperazine (DMPIP), piperazine (PIP), or N,N′-dimethylethylenediamine (DMED) have been investigated and compared with the corresponding diamide model compounds. The results suggest that the rigid DMPIP and PIP polyamides may exist in ordered conformations in 2,2,2-trifluoroethanol (TFE) and tetramethylene sulfone (TMS), while reversible conformational transitions to highly extended forms may be induced by the addition of methanesulfonic acid (MSA). In MSA/TMS mixtures, a change in the optical properties, and thus possibly in the conformations, can be observed around 0.5 mole fraction of MSA. A study of CD at higher temperature indicates that the conformations of the DMPIP and PIP polymides tend to be randomized on heating in TMS and probably also in MSA. No evidence for salt effects on conformation has been observed. Possible ordered conformations have been proposed.     

Synthesis and conformation of asymmetric rigid polyamides

Asymmetric polyamides from the reaction of either optically active trans-1,2-cyclopropanedicarboxylic acid (C3) or trans-1,2-cyclohexanedicarboxylic acid (C6) with 2,7-diazaspiro[4,4]nonane(DSN) were synthesized. The possible conformations of these polymers and their model compounds in 2,2,2-trifluoroethanol (TFE), water, methanesulfonic acid (MSA), and sulfuric acid were examined by circular dichroism (CD), NMR, viscosity, and dipole moment measurements. The racemic polyamides (±)C3·(±)DSN and (±)C6·(±)DSN exist in extended forms. No intrinsic viscosity changes were observed for these two polymers in TFE and MSA. Certain viscosity and spectral changes have been observed for the optically active polyamides, although no specific ordered conformations can be assigned. The optically active diacid units incorporated into the polymer give a conformation unique from the totally extended chain. CD studies seem to evidence some conformational differences among the polyamide derived from (+)C6 diacid and the optically active DSN. By changing the solvent from TFE to MSA a blue shift of the trough was observed for (+)C6·(±)DSN, a red shift for (+)C6·(?)DSN, and an inversion of the CD spectrum for (+)C6·(+)DSN polyamides. The results of the work with (+)C6·(?)DSN in dilute acid solution suggest that the rotation around the C–N bond is a relatively low-energy process. The spectral and intrinsic viscosity data are consistent with this suggestion. No drastic spectral changes have been observed for the C3·DSN polyamides by changing the solvent from TFE to MSA. The amide group in the C3·DSN polyamide and the corresponding model compound prefer a similar conformation with the carbonyl group bisecting the cyclopropane ring. The C3·DSN polyamide seems to exist in an extended form.     

Optical properties of inherently dissymmetric polyamides

A study of the optical rotatory dispersion (ORD), circular dichroism (CD), and ultraviolet spectra (UV) of polyamides derived from optically active biphenyl acid chlorides, and aromatic, and aliphatic diamines, was made. The optically active monomers were (–)-(S)-2,2′-dinitro-6,6′-dimethylbiphenyl-4,4′-dicarbonyl chloride and (–)-(S)-2,2′-dichloro-6,6′-dimethylbiphenyl-4,4′-dicarbonyl chloride. The diamines were o-, m-, and p-phenylenediamine, piperazine, trans-2,5-dimethylpiperazine, and 1,2-pyrazolidine. The ORD spectra of the o-phenylenediaminepolyamide taken in different solvents indicated the existence of some ordered structure in the least polar solvent. All other polyamides existed in a random coil conformation in the solvents employed.     

Polymers from intermediates obtained from hydrogen cyanide

The recent demonstration of an easy synthesis of diiminosuccinonitrile (DISN) from hydrogen cyanide and cyanogen, the reduction of DISN to diaminomaleonitrile (DAMN), and the use of these compounds to form difunctional heterocycles has made several new polyamide intermediates accessible. The 1- and 2-methyl-1,2,3-triazole-4,5-dicarbonyl chlorides have been polymerized interfacially to form high-melting polyamides of good heat stability. Interfacial polymerization of 1-methylimidazole-4,5-dicarbonyl chloride and trans-2,5-dimethylpiperazine has given a polyamide that is water-soluble. The 2,6- and 2,3-pyrazinedicarbonyl chlorides have been similarly converted to high-melting polyamides. 2,6-Dicyano-3,5-dipiperazinylpyrazine has been prepared from tetracyanopyrazine and piperazine and reacted with toluene diisocyanate to form a strong, stiff polyurea. Polyamides were also made from 2,3-diaminoquinoxaline, 1,4,5,6-tetrahydro-5,6-dioxo-2,3-pyrazinedicarbonitrile, and DAMN.     

Synthesis of polyamides by a new direct polycondensation reaction using triphenyl phosphite and lithium chloride

Metal salts such as lithium chloride were found to facilitate significantly the reaction of carboxylic acids and amines promoted by triphenyl phosphite, and the reaction was applied successfully to the direct polycondensation reaction of dicarboxylic acids and diamines and of p-aminobenzoic acid. Among metal salts tested, lithium chloride was most effective to the reaction; the chloride was involved catalytically in the reaction, its addition of about twice equivalent to triphenyl phosphite giving the most favorable results. Triphenyl phosphite was most effective, whereas diphenyl phosphite was less effective, and alkyl esters gave no polymers. The reaction was also markedly affected by solvents, the most favorable results being given in N-methylpyrrolidone (NMP). Various polyamides of high molecular weight were obtained in quantitative yield.     

Synthesis and properties of aromatic polyamides based on non-, methyl-, and phenyl-substituted 4,4′-bis(1,4-phenylenedioxy)dibenzoic acids

4,4′-(1,4-Phenylenedioxy)dibenzoic acid (3), 4,4′-(2,5-tolylenedioxy)dibenzoic acid (Me-3), and 4,4′-(2,5-biphenylenedioxy)dibenzoic acid (Ph-3) were prepared by the nucleophilic substitution reaction of p-fluorobenzonitrile with hydroquinone, methylhydroquinone, and phenylhydroquinone, respectively, followed by alkaline hydrolysis. Several aromatic polyamides having inherent viscosities of 0.66–1.34 dL/g were directly prepared by a Yamazaki phosphorylation polyamidation technique from dicarboxylic acids 3, Me-3, and Ph-3, respectively, with aromatic diamines using triphenyl phosphite and pyridine as condensing agents. The solubility of methyl- or phenyl-substituted polyamides was remarkably enhanced when compared to that of nonsubstituted analogues. Most of the substituted polyamides revealed an amorphous nature and were readily soluble in a variety of organic solvents including N,N-dimethylacetamide (DMAc), N-methyl-2-pyrrolidone (NMP), N,N-dimethylformamide, dimethyl sulfoxide, and m-cresol. Transparent, flexible, and tough films of these polymers could be cast from the DMAc or NMP solutions. These films had tensile strength of 60–100 MPa, elongation to break of 6–11%, and tensile modulus of 1.68–2.25 GPa. The glass transition temperatures (T_g) of most polyamides could be determined by differential scanning calorimetry (DSC) and were in the range of 200–232°C. Thermogravimetric analyses established that these polymers were fairly stable up to 450°C, and the 10% weight loss temperatures were recorded in the range of 458–535°C in nitrogen and 468–528°C in air atmosphere. In general, the phenyl-substituted polyamides exhibited relatively higher T_g, thermal stability, and solubility. © 1996 John Wiley & Sons, Inc.     

Room-temperature polycondensation of β-amino acid derivatives VI. Synthesis of various N-(hydroxyethyl) nylons

Various N-(hydroxyethyl)amino acid esters having a methyl substituent or phenyl group between amine and ester groups have been synthesized and their polycondensation behavior was investigated. These substituted amino acid esters gave amorphous polyamides which were soluble in alcohol. A model reaction between N-(hydroxyethyl)-amine and carboxylic acid ester was carried out in order to elucidate the role of hydroxyethyl group on the polycondensation. It was found that the amidation reaction took place rapidly at room temperature when the alkyl group of the carboxylic acid was small. N-(Hydroxyethyl) polyamides were obtained from N,N′-(bishydroxyethyl)-dicamines and dicarboxylic acid esters. The reaction mechanism of the room-temperature polycondensation reaction is discussed.     

High α transitions of new polyamides based on diamantane

A series of new polyamides were synthesized by direct polycondensation of the 1,6-bis(4-aminophenyl)diamantane with various dicarboxylic acids. The soluble polyamides had high inherent viscosities, ranging from 0.73 to 1.21 dL/g. Polyamides derived from 5-tert-butylisophthalic acid and (±)-1,3-cyclohexanedicarboxylic acid were soluble in N-methyl-2-pyrrolidone (NMP) and pyridine. When NMP and N-dimethylacetamide (DMAc) were added with 3% (w/v) LiCl, the solubilities of polyamides derived from 4,4′-oxybis(benzoic acid) and cis-1,4-cyclohexanedicarboxylic acid were markedly enhanced. Polyamides had tensile strengths of up to 87.8 MPa, elongation to breakage values of up to 19.3%, and initial moduli of up to 2.1 GPa. Dynamic mechanical analysis (DMA) reveals that the polyamides have three relaxations. Their α relaxations occurred at high temperatures, ranging from 380 to 462°C. Three of polyamides exhibited good retention of storage modulus (above 10⁸ Pa) at a temperature exceeding 410°C. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1257–1263, 1998     

Direct synthesis of a polyamide by an enol phosphite and imidazole

Direct polycondensation of various dicarboxylic acids and diamines was effected under mild conditions by using an enol phosphite, diethyl 1-methyl-3-oxo-1-butenyl phosphite (I), in the presence of imidazole. To check the activity of the enol phosphite and various organic bases in an amidation reaction, the model reaction of acetic acid and aniline was carried out, and the yield of acetanilide was estimated by means of gas chromatography. Among organic bases, imidazole was the best in terms of yield of acetanilide. Polycondensation performed by varying solvents, temperature, and amount of imidazole resulted in high yields of polyamides with inherent viscosities of 0.1-0.25.     

Chiral amines in the diastereoselective Mannich-related multicomponent synthesis of diarylmethylamines, 1,2-diarylethylamines, and β-arylethylamines

The multicomponent synthesis of diarylmethylamines, 1,2-diarylethylamines and β-arylethylamines has been undergone starting from aryl- or benzylzinc reagents, aldehydes, and primary or secondary chiral amines. Good to high diastereoselectivities have been obtained from both l-proline ester derivatives 1 and (±)-trans-1-allyl-2,5-dimethylpiperazine (4). The use of R-(+)-1-phenylethylamine (7) provides important diastereoisomeric excesses (∼60%) in conjunction with very high chemical yields. This work constitutes a preliminary entry to the intended development of a more flexible reaction system, involving easily cleavable chiral amines.     

Direct polyamidation with thionyl chloride in N-methyl-pyrrolidone

Mechanistic features of the reaction promoted by thionyl chloride and amides such as N-methylpyrrolidone (NMP) were studied. The reaction was effective in the amidation of carboxylic acids, but not effective in the esterification. The amidation was affected by the kind and the amount of amides used, most favorably by two equivalents of NMP with respect to the acid. These amides were assumed to be involved in the intermediate formation, and the reaction was proposed to proceed via Vilsmeier adducts derived from thionyl chloride and the amides, and through activation of a carboxylic acid different from an acyl chloride. The reaction was successfully applied to the direct polycondensation of aromatic dicarboxylic acids and diamines in NMP at 70°C to produce polyamides with high molecular weights. Initial reaction of dicarboxylic acids with the adducts, additive effect of tertiary amines, and polycondensation temperatures were studied in terms of the inherent viscosity of the polymers produced.     

Polyamides from trans-4-octen-1,8-dioic and trans-2-trans-6-octadien-1,8-dioic acids

Novel polyamides from trans-4-octen-1,8-dioic acid (4-OD) and trans-2-trans-6-octadien-1,8-dioic acid (2,6-ODD) ad linear aliphatic diamines or piperazine were prepared in good yields by low-temperature polycondensation. The polymers obtained were investigated by infrared spectroscopy, x-ray diffraction, and differential scanning calorimetry. Polyamides from 4-OD show high molecular weights and crystallinities and T_m above 500°K, whereas those from 2,6-ODD are very weakly crystalline and decompose without melting in nitrogen at temperatures higher than 550°K. DSC studies revealed in the case of 4-OD polymers with odd diamines, a multiple peak phenomenon in the melting region, strongly dependent from the heating rate. Some hypotheses consistent with this behavior are briefly discussed, and it is concluded that the phenomenon arises from melt recrystallization occurring during the DSC scan.     

Thermotropic polyesters with main chain isomeric naphthylene,trans-1,4-cyclohexylene,and 2,5-pyridinediyl units: The importance of the order of ester linkages in the mesogenic units

Two new series of thermotropic polyesters were prepared and their mesomorphic properties were investigated. The polymers consist of triad aromatic ester-type mesogenic units with decamethylene spacers. The mesogenic units of the first series are composed of isomeric dihydroxynaphthalene moieties as the central structure flanked by two p-oxybenzoyl groups. In the second series the mesogenic units were of reversed ester linkages: the central moieties, derived from 1,4-naphthalene dicarboxylic acid, trans-1,4-cyclohexanedicarboxylic acid, or 2,5-pyridinedicarboxylic acid, are connected on both sides to p-phenylene structures. Two low molecular weight model compounds with 1,4-naphthylene unit at the center of the mesogenic unit were synthesized and their mesomorphic properties were compared with those of corresponding polymers. It was observed both for the model compounds and the polymers containing 1,4-naphthylene units that the linking order of the ester group in the mesogenic unit exerted a decisive influence on the capability for the formation of a mesophase. Thermal and mesomorphic properties were investigated by DSC, on a polarizing microscope equipped with a hot-stage, and by visual observation of stir-opalescence of the melts.     

β-N-Heterocyclic Cyclobutane Carboximides: Synthesis through a Tandem Base-Catalyzed Amidation/aza-Michael Addition Protocol and Facile Transformations

A stereoselective one-pot double derivatization of cyclobutene-1-carboxylic acid via a mild organic base catalyzed amidation/aza-Michael addition of benzo[d]oxazol-2(3H)-ones has been developed. This unprecedented tandem reaction provides access to novel β-N-heterocyclic cyclobutane carboximide derivatives with a trans geometry. The carboximide moiety reacts smoothly with nucleophiles, allowing access to diverse derivatives of trans-β-N-heterocyclic cyclobutanecarboxylic acid, including peptidomimetic structures.     

Synthesis and properties of polyamides derived from 1, 4-bis(4-aminophenoxy)-2-tert-butylbenzene

1, 4-Bis(4-aminophenoxy)-2-tert-butylbenzene was synthesized and used as a monomer to prepare a series of polyamides by the direct polycondensation with various aromatic dicarboxylic acids in N-methyl-2-pyrrolidone using triphenyl phosphite and pyridine as condensing agents. All the polymers were obtained in quantitative yields with inherent viscosities of 0.75–1.75 dL g⁻¹. All the polyamides showed amorphous nature and most of them were soluble in polar solvents. Polyamides derived from 4, 4'-sulfonyldibenzoic acid and 4, 4'-hexafluoroisopropylidenedibenzoic acid were even soluble in common organic solvent such as THF. All polyamide films could be obtained by casting from their DMAc or NMP solutions. The polyamide films had a tensile strength range of 35–84 MPa, an elongation range at break of 3–7%, and a tensile modulus range of 1.2–2.5 GPa. These polyamides had glass transition temperatures between 203–268°C and 10% mass loss temperatures were recorded in the range of 456–472°C in nitrogen and 453–470°C in air atmosphere.     

Synthesis and properties of novel aromatic polyamides derived from 1,5-bis(4-aminophenoxy)naphthalene and aromatic dicarboxylic acids

A new bis(phenoxy)naphthalene-containing diamine, 1,5-bis(4-aminophenoxy)naphthalene, was synthesized in two steps from the condensation of 1,5-dihydroxy-naphthalene with p-chloronitrobenzene in the presence of potassium carbonate, giving 1,5-bis(4-nitrophenoxy)naphthalene, followed by hydrazine hydrate/Pd? C reduction. A series of polyamides and copolyamides were synthesized by the direct polycondensation of the diamine with various aromatic dicarboxylic acids or with mixed dicarboxylic acids in N-methyl-2-pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents. The polymers having inherent viscosity of 0.81–1.25 dL/g were obtained in quantitative yield. Most of the polymers were generally soluble in aprotic solvent such as N,N-dimethylacetamide, N-methyl-2-pyrrolidone, etc. The polymers derived from rigid dicarboxylic acids such as terephthalic acid, naphthalene dicarboxylic acid, and 4,4′-biphenyldicarboxylic acid exhibited crystalline patterns. Glass transition temperatures of polymers were in the range of 230–360°C, and 10% weight loss temperatures in nitrogen and air were above 492 and 470°C, respectively. © 1993 John Wiley & Sons, Inc.     

Synthesis of polyamides from rigid and sterically hindered dicarboxylic acids and diamines under mild conditions

The rate of polycondensation of piperazine with the 2,4-dinitrophenyl, succinimido, phthalimido, and 4-nitrophenyl esters of bicyclo[2.2.2]octane-trans-2,3-dicarboxylic acid was measured and found to decrease in this sequence. In the reaction of two moles of piperazine with one mole of diester, the reactivity of both ester groups was equal. In equimolar mixtures, the second ester group reacts with the second group about ten times slower because of steric hindrance. In the reaction of the esters with N,N′-dimethylethylenediamine no such effects were observed. The aminolysis of the N-hydroxyphthalimido ester stops at low conversions unless a very large excess of triethylamine is added. The catalytic effect of 1,2,4-triazole on the aminolysis was proportional to the triazole concentration. From the rate of ester consumption in the presence of pure triethylamine, the extent of possible racemization of the optically active dicarboxylic acid was estimated. In view of the rate data, the extent of polycondensation, and side reactions, only 2,4-dinitrophenyl and N-hydroxysuccinimido diesters are suitable for the synthesis of polyamides derived from rigid and sterically hindered dicarboxylic acids.