Novel hydroxyethylcellulose-graft-poly acrylamide copolymer for separation of double-stranded DNA fragments by CE

A novel separation medium, hydroxyethylcellulose-graft-polyacrylamide (HEC-g-PAM) synthesized by atom transfer radical polymerization (ATRP), used for dsDNA separation by CE is presented. The separation performance of HEC-g-PAM, which has the same graft density and different graft length, has been investigated in Tris-boric acid-EDTA (TBE) buffer solvent mixtures. The temperature-dependent rheological behavior of HEC-g-PAM was also studied by steady-shear rheometry. The results showed that dsDNA fragments between 72 and 1353 bp was achieved with a 30 cm effective capillary length at 150 V/cm using this type of graft copolymer as a separation medium in bare fused-silica capillaries, and separation improvement is obtained in HEC-g-PAM compared with HEC and poly(dimethylacrylamide (PDMA).     

Ring-opening metathesis polymerization-derived monolithic anion exchangers for the fast separation of double-stranded DNA fragments

Ring-opening metathesis polymerization- (ROMP) derived monoliths were prepared from 5-norborn-2-enemethyl bromide (NBE-CH₂Br) and tris(5-norborn-2-enemethoxy)methylsilane ((NBE-CH₂O)₃SiCH₃) within the confines of surface-silanized borosilicate columns (100 × 3 mm I.D.), applying Grubbs’ first generation benzylidene-type catalyst [RuCl₂(PCy₃)₂(CHPh)]. Monoliths were converted into weak anion exchangers via reaction with diethyl amine. The resulting monolithic anion exchangers demonstrated a very good potential for the anion-exchange separation of nucleic acids applying a phosphate buffer (0.05 mol/L, pH 7) and NaCl (1.0 mol/L) as a gradient former. Fast and efficient separations, indicated by sharp and highly symmetric analyte peaks, were established. Except for the 267 and 298 base pair fragments, the eleven fragments of a ds-pUC18 DNA Hae III digest were baseline separated within ∼8 min. Nineteen fragments of a ds-pBR322 Hae III digest were separated within ∼12 min. There, only the 192 and 213 base pair fragments and the 458, 504 and 540 base pair fragments coeluted. A ds-pUC18 DNA Hae III digest was used as a control analyte in evaluating the influence of organic additives on the mobile phase such as methanol and acetonitrile on nucleic acid separation. Methanol, and even better, acetonitrile improved the separation efficiency and shortened the analysis time.     

基于微芯片电泳的脱氧核糖核酸片段的浓缩和分离

采用超负荷电动供给(electrokinetic supercharging, EKS)预浓缩技术,在微芯片电泳(MCE)上对脱氧核糖核酸（DNA）片段进行浓缩和分离。EKS是集合样品电动进样(EKI)和过渡等速电泳(tITP)的一种在线浓缩方法。研究表明：采用该方法后,在40.5 mm长的单通道芯片上能够实现对低浓度样品的大量进样、浓缩和基线分离。在普通的紫外检测条件(检测波长为260 nm)下,对DNA片段的平均检出限(S/N=3)约为0.07 mg/L,仅为十字芯片上的微芯片电泳检出限的1/40。本文还对浓缩过程中的一些关键因素和定性分析进行了探讨。     

Portable capillary electrophoresis system with potential gradient detection for separation of DNA fragments

A portable capillary electrophoresis (CE) system with a novel potential gradient detection (PGD) was utilized to separate DNA fragments. For the first time it was demonstrated that separation of DNA fragments in polymer solution could be detected by a portable CE system integrated with PGD, with a limit of detection (LOD) comparable to that of the CE-ultraviolet (UV) method. Effects of buffer solution, sieving medium, and applied voltage were also investigated. The portable CE-PGD system shows several potential advantages, such as simplicity, cost effectiveness, and miniaturization.     

Effect of temperature on the separation of long DNA fragments in polymer solution

Electrophoresis of long DNA fragments in polymer solutions is still attractive when performed in short capillaries. Then the separations can be accomplished in minutes rather than hours as is usual in various slab electrophoresis techniques. In this paper we focused on the behavior of large DNA fragments in pulsed field capillary electrophoresis under various temperature conditions. The mobility dependence of fragments of lambda-DNA single-cut mixture on various frequencies at three different temperatures showed that the antiresonance mobility minima are shifted to higher frequencies at higher temperatures. This interesting result is explained in terms of the geometration model of DNA motion.     

Ultra-thin-layer agarose gel electrophoresis. I. Effect of the gel concentration and temperature on the separation of DNA fragments

A novel, rapid and efficient separation method is described for the analysis of double stranded (ds) DNA fragments in the form of horizontal ultra-thin-layer agarose gel electrophoresis. This separation technique combines the multilane, high-throughput separation format of agarose slab gel electrophoresis with the excellent performance of capillary electrophoresis. The electrophoretic separation of the fluorophore (Cy5)-labeled dsDNA molecules were imaged in real time by a scanning laser-induced fluorescence/avalanche photodiode detection system. Effects of the gel concentration (Ferguson plot) and separation temperature (Arrhenius plot) on the migration characteristics of the DNA fragments are discussed. An important genotyping application is also shown by characterizing the polymorphic region (2× or 4×48 base pair repeats) of the dopamine D₄ receptor gene (D₄DR, exon III region) for ten individuals, using PCR technology with Cy5-labeled primers and ultra-thin-layer agarose gel electrophoresis.     

Preparation of methacrylate-based anion-exchange monolithic microbore column for chromatographic separation of DNA fragments and oligonucleotides

In this paper, we report on the preparation of a microbore-scale (1 mm i.d.) anion-exchange monolithic column suitable not only for analytical purposes but also for potentially preparative applications. In order to meet the conflicting requirements of high permeability and good mechanical strength, the following two-step procedure was applied. First, an epoxy-containing monolith was synthesized by in situ copolymerization of glycidyl methacrylate (GMA) and ethylene dimethacrylate (EDMA) within the confines of a silicosteel tubing of 1.02 mm i.d. and 1/16″ o.d. in the presence of a ternary porogenic mixture of 1-propanol, 1,4-butanediol, and water. The monolithic matrix was subsequently converted into weak anion-exchanger via the ring-opening reaction of epoxy group with diethyl amine. The dynamic binding capacity was 21.4 mg mL⁻¹ for bovine serum albumin (BSA) at 10% breakthrough. The morphology and porous structure of this monolith were assessed by scanning electron microscope (SEM) and inverse size exclusion chromatography (ISEC). To optimize the separation efficiency, the effects of various chromatographic parameters upon the separation of DNA fragments were investigated. The resulting monolithic anion exchanger demonstrated good potential for the separation of both single- and double-stranded DNA molecules using a gradient elution with NaCl in Tris–HCl buffer (20 mM). Oligodeoxythymidylic acids (dT₁₂–dT₁₈) were successfully resolved at pH 8, while the fragments of 20 bp DNA ladder, 100 bp DNA ladder, and pBR322-HaeIII digest were efficiently separated at pH 9.     

Glycerol-enhanced mini-polyacrylamide gel electrophoresis for the separation of differentially expressed DNA fragments in cDNA representational difference analysis

Representational difference analysis (RDA) is a widely used technique in molecular biology. However, in practice, its efficiency depends on a rapid and reliable separation of the RDA fragments prior to cloning. To achieve this, we have compared and combined the separation efficiencies of conventional and MetaPhor agarose gel electrophoresis (MAGE) with a glycerol-enhanced mini-polyacrylamide gel electrophoresis (PAGE) system (Gem-PAGE). As anticipated, MetaPhor agarose provided significantly improved resolution over conventional agarose electrophoresis, but the latter remains useful to rapidly confirm the presence of RDA-enriched difference products and direct the concentration of MetaPhor agarose subsequently used for further fragment separation. Additional improvements in resolution were possible by using the Gem-PAGE system. The effect of glycerol on band definition of PAGE was most noticeable as the acrylamide to glycerol ratio (A:G) approached 1:2. Gels in which the A:G ratio was significantly above or below this resulted in both poor morphology and impaired resolution of the bands. By exploiting sequentially agarose-based and Gem-PAGE electrophoresis, the goal in RDA of "one band one product" is now realizable.     

Preconcentration and separation of double-stranded DNA fragments by electrophoresis in plastic microfluidic devices

We have evaluated double-stranded DNA separations in microfluidic devices which were designed to couple a sample preconcentration step based on isotachophoresis (ITP) with a zone electrophoretic (ZE) separation step as a method to increase the concentration limit of detection in microfluidic devices. Developed at ACLARA BioSciences, these LabCard trade mark devices are plastic 32 channel chips, designed with a long sample injection channel segment to increase the sample loading. These chips were designed to allow stacking of the sample into a narrow band using discontinuous ITP buffers, and subsequent separation in the ZE mode in sieving polymer solutions. Compared to chip ZE, the sensitivity was increased by 40-fold and we showed baseline resolution of all fragments in the PhiX174/HaeIII DNA digest. The total analysis time was 3 min/sample, or less than 100 min per LabCard device. The resolution for multiplexed PCR samples was the same as obtained in chip ZE. The limit of detection was 9 fg/microL of DNA in 0.1xpolymerase chain reaction (PCR) buffers using confocal fluorescence detection following 488 nm laser excitation with thiazole orange as the fluorescent intercalating dye.     

An automated capillary electrophoresis system for high-speed separation of DNA fragments based on a short capillary

A high-speed DNA fragment separation system was developed based on a short capillary and a slotted-vial array automated sample introduction system. The injection process of DNA sample in a short capillary was investigated systematically with three injection techniques including constant-field-strength, low-field-strength and translational spontaneous injections. Under the optimized conditions, picoliter-scale sample plugs (corresponding to ca. 20-μm plug length) were obtained, which ensure the high-speed and high-efficiency separation for DNA fragments with a short effective separation length. Other separation conditions including the sieving matrix concentration, separation field strength and effective separation length were also optimized. The present system was applied in the separation of ΦX174-Hae III digest DNA marker. With an effective separation length of 2.5 cm, the separation could be achieved in <100 s with plate heights ranging from 0.21 to 0.74 μm (corresponding to plate numbers from 4.86 × 10(6) to 1.36 × 10(6)/m). The repeatabilities for the migration time of the eleven fragments were between 0.4 and 1.1% RSD (n=8). By using the automated continuous injection method, the separation for four different DNA samples could be achieved within 250 s. The present system was further applied in the fast sizing of real DNA samples of PCR products.     

Mannitol influence on the separation of DNA fragments by capillary electrophoresis in entangled polymer solutions

A new kind of sieving matrix is presented in this paper to allow satisfactory separation of DNA fragments in a relatively low viscous solution. When a certain amount of mannitol was added to cellulose solution not concentrated enough to separate PGEM-3Zf(+)/HaeIII standards well, a polymer solution with low viscosity but with very good separation effects was obtained. The separation result of this sieving buffer was comparable with those using highly concentrated cellulose solutions. The sieving ability of solutions with different cellulose concentrations and different amounts of mannitol has been investigated. It was proved that 0.5% was the minimum hydroxypropylmethylcellulose (HPMC) concentration that could be used to separate DNA fragments satisfactorily. HPMC solutions with a concentration of less than 0.5% could not separate the standard DNA fragments even in the presence of mannitol. It was found that 6% was the optimized mannitol concentration because either more or less mannitol will lead a decrease of resolution. The principle of the positive influence of mannitol has also been discussed.     

Anion-exchange chromatography of DNA restriction fragments.

The abilities of several high-performance liquid chromatography (HPLC) anion-exchange packings to separate DNA restriction fragments, ranging in size from 50 to 23,000 base pairs, were studied. The ion exchangers investigated include the porous packings Protein-Pak DEAE-5PW, Nucleogen-DEAE 4000-7, Poros-Q and BakerBond WP-PEI, and the non-porous packings TSK Gel DEAE-NPR, Gen-Pak FAX, and ProPac PA1. The results indicated that the non-porous packings could separate all 18 fragments (less than 600 base pairs) in a pBR322 DNA-HaeIII digest, while of the porous packings, only Nucleogen-DEAE 4000-7 could resolve DNA fragments in this size range. Only Gen-Pak FAX and TSK Gel DEAE-NPR could significantly resolve the very large DNA fragments (125-23,000 base pairs) of a lambda DNA-HindIII digest. The chromatographic parameters governing this separation by Gen-Pak FAX were optimized so that six of eight fragments were resolved. Split-peak phenomena were observed at low flow-rates when employing non-poros packings, but were eliminated by the incorporation of organic modifiers or surfactants, suggesting that, under certain conditions, hydrophobicity may play a significant role in separations on this packing. Gen-Pak FAX also separated 21 of 23 fragments in a 1000-base pair DNA ladder, a performance which, in addition to the quantitative capabilities of HPLC, makes anion-exchange chromatography a powerful method complementary to slab-gel electrophoresis, and perhaps preferable over agarose gel electrophoresis for applications such as the confirmation of plasmid integrity.     

On-column preconcentration and separation of DNA fragments using polymer solutions in the presence of electroosmotic flow

We demonstrated DNA preconcentration and separation in the presence of electroosmotic flow (EOF) using poly(ethylene oxide) (PEO) solutions. After injecting large volumes of DNA samples into a capillary filled with free tris(hydroxymethyl)aminomethane (Tris)-borate (TB) buffers, PEO solutions entered the capillary by EOF and acted as sieving matrices. In contrast to conventional methods (in the absence of EOF), controlling the EOF was also useful for resolution optimization. We have found that PEO adsorption on the capillary wall was more pronounced when low ionic strength buffers were used. Thus, the EOF decreased with increasing injection length, which led to longer migration times and changes in resolution and stacking efficiency. All resolution values were higher than 1.5 when 1.0 microg/mL DNA samples were injected at 240 V/cm for 60 s (0.67 microL). In addition, as low as 0.015 microg/mL DNA samples (an about 66-fold increase in sensitivity) were detected when the injection was performed at 250 V/cm for 60 s.     

Micropreparative fractionation of DNA fragments on metathesis-based monoliths: influence of stoichiometry on separation

New antibiotics were recently developed, among which are the (fluoro)quinolones. This paper presents an analytical method which allows the determination of 11 (fluoro)quinolones in swine kidneys: norfloxacin, ofloxacin, cinoxacin, oxolinic acid, nalidixic acid, flumequine, enrofloxacin, enoxacin, ciprofloxacin, danofloxacin and marbofloxacin. The procedure involves a rapid and efficient pre-treatment by solid-phase extraction (recoveries 83-98%), followed by the sensitive and selective determination of all compounds in a single run using LC-ESI-MS-MS. Multiple reaction monitoring (MRM) was used for selective detection of each (fluoro)quinolone. Quinine was selected as internal standard. The accuracy of the method, expressed as recovery, was between 89 and 109%; the repeatability had a maximum RSD lower than 15%. The limits of detection (LOD) were much lower than the respective Maximum Residue Limits (MRL)/4.     

Stepwise capillary electrophoretic separation of DNA fragments using poly(ethylene oxide) solutions in the presence of electroosmotic flow.

Single-base resolution in the separation of DNA markers V and VI was achieved in the presence of electroosmotic flow (EOF), using poly(ethylene oxide) (PEO) solutions containing ethidium bromide (EtB) under isocratic conditions. Furthermore, a new approach called stepwise capillary electrophoresis (SCE) has been developed for DNA analysis, including stepwise changes in PEO concentration, EtB concentration as well as both PEO and EtB concentrations, wherein the EOF was used to introduce different PEO solutions into the capillary during the separation. DNA fragments smaller than 80 bp were both detected under isocratic conditions using 20 micrograms/ml EtB, and SCE using 1 and 20 micrograms/ml EtB, but not under isocratic conditions using 1 microgram/ml EtB. Resolution and speed of the DNA separation in SCE were different from those obtained from isocratic means, indicating that DNA underwent different concentrations of PEO and EtB in SCE. For example, DNA fragments with 458 and 504 base pairs (bp) were partially resolved in SCE, but not under isocratic conditions. The results further suggest that it is worth developing gradient techniques for widening the separation range and enhancing resolution in DNA analysis.     

Comparison of the separation of large DNA fragments in the presence and absence of electroosmotic flow at high pH

This paper describes the analysis of large DNA fragments at pH > 10.0 by capillary electrophoresis (CE) in the presence of electroosmotic flow (EOF) using hydroxyethylcellulose (HEC) solution. HEC solution in the anodic reservoir enters the capillaries filled with high-pH buffer by EOF after sample injection. With respect to resolution, sensitivity, and speed, separation conducted under discontinuous conditions (different pH values of HEC solutions and buffer filling the capillary) is appropriate. Using HEC solution at concentrations higher than its entanglement threshold ensures a good separation of large DNA fragments in the presence of EOF at high pH. In addition to pH and HEC, the electrolyte species, dimethylamine, methylamine, and piperidine, play different roles in determining the resolution. The separation of DNA fragments ranging in size from 5 to 40 kilo base pairs was completed in 6 min using 1.5% HEC prepared in 20 mM methylamine-borate, pH 12.0, and the capillary filled with 40 mM dimethylamine-borate, pH 10.0. In comparison, this method allows faster separations of large DNA fragments compared with that conducted in the absence of EOF using dilute HEC solutions.     

Use of disk electrophoresis for the separation of large peptide fragments of proteins

Summary The disk electrophoresis of peptide fragments from porcine pepsin obtained by cleaving the pepsin with cyanogen bromide has been performed. A method has been developed for extracting the colored peptide fractions after electrophoresis in polyacrylamide gel. An amino-acid analysis has been performed of peptide fragments B1, B2, and B4 isolated by disk electrophoresis. The results obtained have been compared with the amino-acid composition calculated from the structures of these peptides. The possibility has been shown of using the method described during structural investigations of both proteins and their low-molecular-weight fragments.The peptide preparations were supplied to us by I. Surova, V. Ostoslavskaya, L. Revina, I. Puracheva, É. Vakhitova, and G. Muratova. The amino-acid analysis was performed by E. Timokhina, A. Balduev, G. Fedyukina, O. Khodova, and N. Ivashechkina.All-Union Scientific-Research Institute of the Genetics and Breeding of Industrial Microorganisms. Translated from Khimiya Prirodnykh Soedinenii, No. 2, pp. 219–222, March–April, 1975.     

Carbon nanotube-enhanced separation of DNA fragments by a portable capillary electrophoresis system with contactless conductivity detection

It was demonstrated that separation of DNA fragments by a CE-contactless conductivity detection system (CE-CCD) could be enhanced with multiple-wall carbon nanotubes (MWCNs) as buffer additive. For HaeIII digest of PhiX174 DNA, optimized MWCN concentration was obtained when the MWCN was above its threshold concentration, at which MWCN could form a network in the buffer as pseudostationary phase to provide additional interaction sites. In the case of larger DNA, MWCN near or below its threshold concentration was enough to provide great improvement of the resolution, which was shown by the separation of the 2-Log DNA ladder. Furthermore, the buffer containing MWCN could provide a more stable baseline in the CE-CCD system, owing to less fluctuation of its conductivity. Compared with CE-UV, CE-CCD with MWCN could provide lower LODs as well as better resolution.