聚丙烯酸控制合成的聚合物/二氧化硅复合纳米球

以3-氨丙基三甲氧基硅烷(APMS)和正硅酸乙酯(TEOS)为硅源, 与阴离子聚合物聚丙烯酸(PAA)链之间通过S^-N⁺-I^-机理组装合成了聚丙烯酸-二氧化硅(PAA/SiO₂)复合纳米球. SEM, TEM, TG和FTIR表征结果表明, 合成的纳米球是聚丙烯酸和二氧化硅复合物, 平均直径约为80 nm. 在合成PAA/SiO₂复合纳米球的体系中, 加入不同量的有机溶剂THF能够调控复合球的尺度.     

纳米二氧化硅物理吸附乙醇的密度泛函研究

利用密度泛函理论, 采用周期性边界条件及簇方法研究了无定型纳米二氧化硅的表面结构以及其对小分子吸附物乙醇的吸附性质. 计算结果表明, 小簇模型在研究特定种类的吸附方面具有优势, 而周期性切片模型更能真实地反映纳米二氧化硅的表面环境; 乙醇在二氧化硅表面的吸附主要依赖于氢键作用, 并倾向于充当氢键受体的角色.     

二氧化硅@聚合物同轴纳米纤维

The preparation and formation mechamsm ot silica/polyvinylpyrrolidone(PAN) coaxial nanofibers were presented in this paper. The PVP-PAN composite nanofibers were obtained via an electrospinning technique, while SiO2 nanoparticles were prepared according to a Stoeher method. The measurements of water contact angle(WCA), the compared results of silica coating PVPPAN composite nanofibers with PAN nanofibers indicate that much PVP resided on the composite nanofiber surface, which resuks in the occurrence of SiO2@polymer coaxial nanofibers due to the formation of hydrogen bonding between silica and composite nanofibers and subsequent adsorption of silica on the fiber surface.     

囊泡状二氧化硅的合成及油气吸附性能

以正硅酸四甲酯(TMOS)为硅源,P123(EO20PO70EO20)为表面活性剂,在p H=6的磷酸缓冲体系中制备了囊泡状二氧化硅材料.利用乙醇萃取脱除模板剂P123,电镜观测结果表明所得二氧化硅具有大孔囊泡结构,N2吸附结果表明其具有高比表面积和大孔容.通过Boehm滴定法确定了硅羟基数量与吸水率呈正相关.用囊泡状二氧化硅材料与商业化活性炭(AC)和硅胶(SG)对水蒸气、正己烷和油气进行静态吸附.在自建的动态正己烷吸附装置上用对囊泡状二氧化硅材料和商业化AC和SG对正己烷进行动态吸附.吸附结果表明,囊泡状二氧化硅材料的静/动态吸附容量和稳定性都远高于商业化活性炭和硅胶.     

生物亲和性壳聚糖-二氧化硅复合纳米粒子的合成及其吸附DNA特性研究

采用反相微乳液法制备了壳聚糖-二氧化硅复合纳米粒子,通过透射电镜（TEM）、红外光谱方法、Zeta电位实验等对所合成的复合纳米粒子的结构和性质等进行了表征.结果显示,基于壳聚糖与silica之间超分子作用所形成的复合纳米粒子呈规则的球形,粒径为50 nm左右,具有良好的单分散性和微孔结构,Zeta电位测定结果表明复合纳...     

利用聚合物乳液合成聚甲基丙烯酸甲酯/二氧化硅纳米杂化材料

通过正硅酸乙酯分别在聚甲基丙烯酸甲酯乳液和四氢呋喃溶液中的溶胶－凝胶反应制备出不同的聚甲基丙烯酸甲酯／二氧化硅复合材料。利用扫描电镜、透镜电镜、差热分析和热失重对试样进行了分析。结果表明，利用聚合物乳液可以获得纳米分散的聚甲基丙烯酸甲酯／二氧化硅复合材料，并且在某种程度上其分散尺度小于利用聚合物溶液获得的复合材料。同时，利用聚合物乳液来制备聚甲基丙烯酸甲酯／二氧化硅杂化材料更有利于凝胶过程中二氧化硅网络的形成。     

氢气在单壁碳纳米管束的吸附的密度泛函研究

作者利用密度泛函理论（DFT）计算了氢气在单壁碳纳米管束（SWNTs)中管内 和管间的吸附。考察了温度，孔径以及压力对吸附的分子数密度，重量百分比，单 位体积储存能力以及超额吸附量的影响。DFT计算发现，较大的孔径有利于氢气在 SWNTs中的吸附且氢气在管隙中的吸附不可忽略。计算表明在77 K和6 MPa时，氢气 在2.719 mm的SWNTs的总的吸附的重量百分比分别可达到13.2 wt%，这约是美国能 源部（DOE）目标值的两倍，而单位体积储存能力在DOE目标值附近，而在300 K和 6 MPa时，氢气在2.719 nm的SWNTs的总的吸附的重量百分比仅为1.5 wt%。通过实 验结果与计算结果的比较表明，密度泛函理论的计算结果支持SWNTs有较高的吸附 储氢能力的实验结论。     

聚丙烯酸在纳米TiO2表面吸附行为的研究

讨论了聚丙烯酸在纳米TiO₂水悬浮体系中的吸附行为.红外光谱分析和吸附实验结果表明,纳米TiO₂通过氢键吸附PAA.PAA吸附量随着浓度的升高而增大直至饱和吸附量,且分子量越大,饱和吸附量越大.pH值增大,则饱和吸附量减小.在相同条件下,表面吸附层的厚度随PAA分子量、浓度和pH值增大而增大.这是由PAA在颗粒表面构型的变化所致.吸附PAA后的纳米TiO₂的表面电荷密度和ζ电位发生变化,pHiep值向低值方向移动.表面吸附自由能的计算结果说明,PAA在纳米TiO₂表面的吸附是自发过程.     

原位法合成Cu-BTC负载二氧化硅吸附材料的研究

采用溶剂热法,将均苯三甲酸(H3BTC)与硝酸铜进行反应合成了金属-有机骨架(Metal-Organic Frameworks,MOFs)微孔材料Cu-BTC;利用原位合成法,将Cu-BTC负载到介孔/大孔二氧化硅孔道中,获得介孔CuBTC-SiO2材料。通过静态吸附实验,测定了正己烷(n-C6)、环己烷(c-C6)和正癸烷(n-C10)在Cu-BTC及CuBTC-SiO2上的吸附速率曲线,结果表明,将微孔材料Cu-BTC负载在SiO2之后,CuBTC-SiO2中既有微孔又有一定量的介孔,适量的介孔结构可减小其对正己烷的静态饱和吸附量,但增加对环己烷和正癸烷的静态饱和吸附量。实验测得CuBTC-SiO2对c-C6和n-C10都具有更大的静态饱和吸附量。因此CuBTC-SiO2材料可望应用在烷烃的吸附分离上。     

Synthesis of anionic gemini surfactant-templated mesoporous silica nanoparticles and its adsorption application for Pb2+

Abstract

Amino-functionalized mesoporous silica nanoparticles (AFMSN) were prepared based on the self-assembly process of the pre-fabricated template of anionic gemini surfactant. The perfect mass ration of the reactants for the synthesis of the AFMSN with high surface area and amino loading was optimized by orthogonal experiments. Adsorption capability of the optimized product for lead ion (Pb²⁺) was investigated in detail. Specially, the effects of the amino content, solution pH, adsorbent dosage, temperature, and interference of other metal ions on the removal efficiency of Pb²⁺ were studied. It is found that these factors can greatly affect the removal efficiency of Pb²⁺ and the prepared adsorbent exhibits the high adsorption selectivity for Pb²⁺. At an optimal condition, the AFMSN adsorbent presents an excellent adsorption capacity for Pb²⁺ up to 211.42?mg/g. The adsorption kinetics study revealed that the pseudo-second-order model could well describe the Pb²⁺ adsorption process, and the adsorption isotherm was fitted well with the Langmuir model. More importantly, the AFMSN adsorbent could be recycled 8 times and a high adsorption efficiency of Pb²⁺ could still be maintained. Therefore, the prepared AFMSN adsorbent may find practical application in removing Pb²⁺ from the polluted water.     

V-P-O/TiO~2-SiO~2催化剂的制备、表征及其在丙烷氧化制取丙 烯酸反应中的应 用研究

通过湿磨法,将钒-磷-氧(V-P-O)氧化物负载于钛硅干凝胶(TiO~2-SiO~2)上,制备了V-P-O/TiO~2-SiO~2氧化物催化剂,并运用BET,XRD,TEM及XPS等技术考察了润湿剂,V-P-O的含量及焙烧条件对催化剂结构的影响。由BET方法发现,以异丁醇为润湿剂对催化剂表面积影响较小。XRD和TEM考察结果表明,所制备的催化剂有较高的热稳定性。通过XPS分析,证实钒元素主要以V(IV)价态存在于催化剂的表面。V-P-O/TiO~2-SiO~2催化剂在丙烷氧化反应中显示了良好的催化性能。     

Time-resolved fluorescence anisotropy measurements of the adsorption of Rhodamine-B and a labelled polyelectrolyte onto colloidal silica

 The application of time-resolved fluorescence anisotropy measurements (TRAMS) to the investigation of the adsorption of the dye Rhodamine B and a Rhodamine B-labelled cationic polyelectrolyte onto colloidal silica (Ludox) is described. For Rhodamine B the time-resolved fluorescence anisotropy behavior observed can be interpreted using a model consisting of fluorophores with two distinct fluorescence decay lifetimes and two rotational correlation times corresponding to the fluorophore free in solution and bound to the Ludox. Details of the binding obtained from a global analysis of the data are reported. Restricted motion of the fluorescently labelled polyelectrolyte is also observ-ed on adsorption. The considerations for the general application of TRAMS for monitoring adsorption behavior are discussed. Received: 8 July 1998 Accepted: 10 August 1998     

活性炭吸附CO2与其微孔体积的关系

对五种活性炭样品进行液氮温度下的N2吸附、碘吸附测定和冰点下的CO2吸附表征。结果表明,碘吸附值测定法和基于N2吸附等温线的BET方程、D-R方程,孔结构参数都不能正确反映活性炭对CO2的吸附特性;由CO2吸附等温线得到的D A模型参数也不适合分析活性炭吸附CO2特性;CO2吸附等温线的密度泛函理论（DFT）分析结果表明,CO2在活性炭上的吸附发生在极微孔内,DFT分析的微孔孔容与吸附等温线反映的吸附性能完全一致。因此,根据CO2吸附等温线的DFT模型是准确反映活性炭吸附CO2特性的表征分析方法。     

Two different approaches to XPS quantitative analysis of polyelectrolyte adsorption layers

X-ray photoelectron spectroscopy (XPS) was employed to quantify adsorption of polyelectrolytes from aqueous solutions of low ionic strength onto mica, glass, and silica. Silica surfaces were conditioned in base or in acid media as last pre-treatment step (silica-base last or silica-acid last, respectively). Consistency in the determined adsorbed amount, Γ, was obtained independent of the choice of XPS mode and with the two quantification approaches used in the data evaluation. Under the same adsorption conditions, the adsorbed amount, Γ, varied as Γ_mica > Γ_{silica-base last} ≈ Γ_glass > Γ_{silica-acid last}. In addition, the adsorbed amount increased with decreasing polyelectrolyte charge density (100% to 1% of segments being charged) for all substrates. Large adsorbed amount was measured for low-charge density polyelectrolytes, but the number of charged segments per square nanometer was low due to steric repulsion between polyelectrolyte chains that limited the adsorption. The adsorbed amount of highly charged polyelectrolytes was controlled by electrostatic interactions and thus limited to that needed to neutralize the substrate surface charge density. For silica, the adsorbed amount depended on the cleaning method, suggesting that this process influenced surface concentration and fraction of different silanol groups. Our results demonstrate that for silica, a higher density and/or more acidic silanol groups are formed using base, rather than acid, treatment in the last step.     

Synthesis of nitrogen doped activated carbon/polyaniline material for CO2 adsorption

The equilibrium adsorption isotherms of carbon dioxide and nitrogen on the nitrogen doped activated carbon (NAC) prepared by the chemical activation of a pine cone‐based char/polyaniline composite were measured using a volumetric technique. CO₂ and N₂ adsorption experiments were done at three different temperatures (298, 308, and 318 K) and pressures up to 16 bar, and correlated with the Langmuir, Freundlich, and Sips models. The Sips isotherm model presented the best fit to the experimental data. The N‐doped adsorbent showed CO₂ and N₂ adsorption capacity of 3.96 mmol·g⁻¹ and 0.86 mmol·g⁻¹, respectively, at 298 K and 1 bar. The selectivity predicted by ideal adsorbed solution theory (IAST) model was achieved 47.17 for NAC at 1 bar and y_N2 = 0.85 which is a composition similar to flue gas. The results showed that NAC adsorbent has a high CO₂‐over‐N₂ selectivity in a binary mixture. The relatively fast sorption rate of CO₂ on NAC compared to N₂ indicates the stronger affinity between CO₂ and amine groups. The isosteric heat of adsorption of CO₂ by the NAC demonstrated the physico‐chemical adsorption of CO₂ on the adsorbent surface. These data showed that prepared NAC could be successfully applied in separation of CO₂ from N₂.     

Porous properties of silylated mesoporous silica and its hydrogen adsorption

Porous properties of mesoporous silica silylated with various organic silanes were examined and their hydrogen adsorption properties were measured at 77 K. By silylation of the mesoporous silica, the specific surface area, pore radius and pore volume steeply decreased depending on both the size of the silane and the amount actually incorporated into the mesoporous framework. The pores reduced in size depending on the amount of modifying silane and vanished completely in the samples silylated with 3-aminopropyltriethoxysilane and phenyltrichlorosilane. Hydrogen adsorption isotherms of the silylated samples were measured at 77 K. With the exception of the sample with phenyltrichlorosilane, hydrogen adsorption volumes were proportional to the surface area with a slope of around 1.1 molecules/nm². On the other hand, for the sample treated with phenyltrichlorosilane, a large hydrogen adsorption volume of around 38.1 molecules/nm² was obtained. On heating the silylated compounds at 500 °C, micropores formed and the hydrogen adsorption volume increased by 1.5 times or more due to the development of micropores.     

针状TiO2锐钛矿晶粒溶胶的制备、结构及形成机理研究

The PTA sol was prepared using titanyl sulfate(TiOSO₄), peroxide (H₂O₂) and ammonia (NH₃·H₂O) as raw materials. The semitransparent, light yellow AS(autoclaved sol) with ultra-fine needle-like anatase crystals was synthesized by autoclaving the PTA sol at 80～100 ℃ for different times. The anatase crystals were needle-like and 80 nm in length, 20～30 nm in diameter. The FTIR, XRD, SEM were used to analyse the chemical structure, properties of the AS and influencing factors during the sol preparation. The mechanism model of the AS formation was established based on the inorganic and crystal structural chemistry. The PTA molecules were decomposed to form Ti⁴⁺ under hydrothermal conditions and the Ti⁴⁺ were hydrated with water to get [Ti(OH)₄(OH₂)₂]⁰, a growing units of the anatase crystals. The appearance of the needle-like anatase crystals and the anatase precipitate are also explained in this paper.     

纳米级MnO2的制备与电化学性质研究（II）溶胶凝胶法制备掺铋改性纳米...

用溶胶凝胶法制得掺铋二氧化锰。经ＸＲＤ、ＴＥＭ、ＩＣＰ、化学分析等测定，确定了所得样品的主要晶型为α－ＭｎＯ２，所掺铋的晶态为Ｂｉ２Ｏ３，为纳米级颗粒（记为ｎｍ－Ｂｉ－ＣＭＤ）。用它与掺铋电解二氧化锰（记为Ｃｉ－ＥＭＤ）以最佳配比混合，可大大提高充放电容量。通过循环伏安、交流电导率、交流电阻等测试所测得的电导率、电极表面的分形维数，初步解释了充入电性能改善的原因主要是由于提高了最佳配比样品的导电率     

Non-equilibrium adsorption at solid/liquid interfaces from polyelectrolyte solutions

The poly(2-vinylpyridine) layer was established at the Pyrex glass/water interface with periodic phases of adsorption/desorption runs observed over several days. This was evidenced by determining the concentration of radio-labelled molecules in the solution equilibrating the glass beads as a function of time (the effluent) while the same radio-labelled polymer was slowly supplied by injecting the polymer solution into the reactor containing the adsorbent at a controlled extremely slow rate. Although the adsorption (or the desorption) steps seemed to present some periodic character, they were better correlated with the successive bulk concentration thresholds that were established with time when the initial surface was free of polymer at time zero. Even when the adsorbent was coated at different degrees, desorption steps were correlated to the overstepping of decreasing concentration thresholds. Adsorption and desorption runs were attributed to the existence of different typical interfacial conformations of the adsorbed macromolecules that only can be stabilised in the adsorbed state when the layer was equilibrated with the polymer solution of a certain concentration. Macromolecule were definitely adsorbed when the reconformation process led to a flat conformation (trains). Macromolecules adsorbed with a conformation close to their solution conformation may be desorbed as a result of the reconformation process affecting previously adsorbed neighbour molecules (in the case of partially coated surfaces at time zero of injection). Macromolecules with loops and tails were retained on the surface when the polymer concentration in the bulk was progressively increased (for uncoated surfaces at time zero of injection). All these effect were attributed to the combined influence of topological effects on adsorption and reconformation of adsorbed macromolecules that characterise the non-equilibrium adsorption processes.