钛基二氧化铅电极上氯析出过程的研究

用极化曲线法研究了钛基二氧化铅电极(β-PbO_2)在NaCl溶液中的阳极析氯过程。结果表明,反应速度与Cl~-离子浓度成正比,H~ 离子通过OH~-离子的竞争吸附对析氯过程起促进作用。电极转速对阳极极化曲线没有影响,说明扩散过程不起控制作用。稳态动力学数据指出,氯的析出机理符合电化学放电规律,速度控制步骤为:MCl~-_(adi)→MCl~-_(adi e)。     

巯基—聚吡咯薄膜修饰电极的制备及其电化学性能

通过将巯基乙酸作为一种支持电解质,将巯基固定在导电聚吡咯薄膜电极上,从而制得巯基—聚吡咯薄膜修饰电极,该修饰电极保持了巯基的螯合性能,并具有良好的稳定性。对水溶液中的重金属离子具有很好的吸附作用,其灵敏度与未修饰的玻碳电极相比,测汞离子时电沉积提高了3倍,化学吸附时提高了近5倍。并对其吸附机理进行了初步的探讨,证明了其对汞离子的吸附为不可逆的产物弱吸附。     

Tetren对锌电沉积过程的阻化作用和催化作用

应用线性扫描伏安法和微分电容法研究了锌酸盐镀锌中四乙烯五胺(tetren)对Zn(OH)₄^2-放电步骤的阻化和催化作用.结果表明,tetren在汞电极/溶液界面上具有较强的吸附性,且随着te-tren浓度提高吸附量增加,吸附电势区朝负电势方向扩大,tetren在-1.3～1.45V间可阻化Zn(OH)₄^2-放电.在小于-1.45V电势区可观察到两个催化电流峰,提高tetren浓度,两峰重合,其峰电流与tetren(大于5×10^-3mol/L时)及ZnO浓度成正比,而与NaOH浓度成反比.     

铜离子选择性微电极用于银杏根尖离子流的时空监测

通过在超细铜丝尖端(直径约为16μm)电沉积硒化铜薄膜的方法制备了全固型铜离子选择性微电极,研究了它对铜离子的能斯特响应,包括选择性、检出限和响应时间等参数;使用该电极检测到银杏(Ging-ko)根尖表面的铜离子时空流,并首次发现Gingko根细胞对Cu2 摄取具有振荡性。     

不同聚合度聚乙二醇对A30碳钢的缓蚀性能

通过开路电位测量法、动电位极化曲线法和电化学阻抗谱法研究了表面活性剂聚乙二醇对A30碳钢的缓蚀作用,初步推测了其缓蚀机理．分别选取聚合度为600、2000、4000、6000的四种聚乙二醇进行实验,结果表明,聚乙二醇对碳钢的最高缓蚀率接近90％．聚乙二醇分子量对缓蚀作用有明显影响,相同浓度时聚合度越大,缓蚀性能越强．三种方法得到的结果具有同一性．     

末端硫醇化的甲氧基聚乙二醇分子自组装膜电极对碘离子的电化学分析研究

碘离子的测量方法有化学法和电化学方法等多种,电化学方法有离子选择性电极、阴极溶出伏安法等［１,２］,但以上方法易受共存离子的干扰．自组装膜修饰电极具有分子识别功能,因而可用于特定物质的检测［３］．末端硫醇化的聚乙二醇分子在金电极表面形成自组装膜后具有分子识别特性［４］,碘离子和聚乙二醇膜有较好的相容性,可以进入膜内进而到达电极表面进行反应,而其它干扰离子较难进入．因而,该膜电极能用于碘离子测定,检测下限低,并具有较强的抗干扰能力．１　实验部分１．１　试剂及仪器　甲氧基聚乙二醇（ＭＷ＝５０００）等…     

电沉积n—CdSe在多硫溶液界面上的电荷转移机理

通过测定平带电位,澄清了OH~-离子在CdSe电极上的吸附情况,发现在S、S~(2-)、OH~-溶液中S~(2-)离子优先吸附,结合旋转环盘电极测量,证明n-CdSe电极在多硫溶液界面上的电荷转移过程。     

高分子聚电解质型电极添加剂的合成和性能测试

合成阳离子聚电解质作为新型电极添加剂 ,考察了新型电极添加剂对离子交换膜燃料电池放电性能的影响。实验结果表明在电极中加入适量的新型电极添加剂可显著地提高燃料电池的放电性能。当电极中新型添加剂的含量为 1 .8%时 ,燃料电池的放电电压和电流密度都处于高峰值状态。实验结果还发现电荷密度为45%的聚电解质型电极添加剂对燃料电池放电性能的改性作用与价格昂贵的进口Nafion乳液添加剂的改性作用基本处于同一水平。因此在离子膜燃料电池中可采用廉价易合成的聚电解质型电极添加剂取代Nafion乳液添加剂。     

巯基乙酸修饰金电极的电化学行为及对铜离子的测定

通过共价自组装的方法制备了巯基乙酸单分子层修饰金电极.在含有铜离子的磷酸缓冲液中搅拌吸附,铜离子与修饰电极表面的巯基乙酸形成的活性配合物吸附在电极表面.用该电极对不同浓度的铜离子进行检测,发现峰电流随铜离子浓度的增大而增大,在0.05~1μmol/L之间出现良好的线性关系,其最低检测限可达10 nmol/L.     

用双表面活性剂为共模板合成中孔分子筛MCM-48

利用水热法以非离子表面活性剂聚乙二醇辛基苯基醚和阳离子表面活性剂十六烷基三甲基溴化铵为共模板合成了中孔分子筛MCM-48.实验中发现利用较强的范德华力和氢键,聚乙二醇辛基苯基醚可在很大程度上降低合成MCM-48所需阳离子表面活性剂的用量,且利于制备有序性好、骨架聚合度高、稳定性好的MCM-48.通过调节聚乙二醇辛基苯基醚与十六烷基三甲基溴化铵的比例,可得到不同物相结构的分子筛.     

离子强度对膨润土/木质素磺酸钠接枝丙烯酰胺-马来酸酐复合吸附树脂吸附Pb2+/Cu2+的影响

为揭示外加电解质离子强度对重金属离子吸附的影响规律与内在机制, 制备了膨润土/木质素磺酸钠接枝丙烯酰胺-马来酸酐复合吸附树脂(BLPAMA), 研究了外加电解质离子强度对BLPAMA吸附单一和二元Pb²⁺/Cu²⁺的影响规律, 以及有、无外加0.2 mol/L NaNO₃时BLPAMA对二元Pb²⁺/Cu²⁺的吸附等温线、吸附热力学及吸附动力学。 结果表明, 在单一Pb²⁺或Cu²⁺溶液中, 随离子强度增加, Pb²⁺和Cu²⁺吸附量降低;在二元Pb²⁺/Cu²⁺溶液中, 随离子强度增加, Pb²⁺吸附量降低而Cu²⁺吸附量提高。     

Adsorption Mechanism of Composite Whisker on Copper Ions and Lead Ions

A new kind of inorganic composite adsorbent based on chitin whiskers(CHW) and potassium tetratitanate whiskers(PTW) was synthesized via the thermal deposition to remove Cu²⁺ and Pb²⁺ from wastewater. CHW could be successfully coated on the surface of PTW when thermal treated 8 times. The adsorption process was better fitted with the Langmuir and Freundlich models. The adsorption process was more conformed to the Pseudo-second-order model. The results from XPS(X-ray photoelectron spectrum) further show that the adsorption mechanism between CHW-PTW and Cu²⁺, Pb²⁺ are both ion exchange and chemical adsorption. Thermodynamic parameters suggest that the adsorption processes are nonspontaneous. The adsorption of Cu²⁺ and Pb²⁺ is endothermic and exothermic, respectively.     

改性层状双氢氧化物对铜离子(Ⅱ)和双酚A的协同吸附

采用离子交换法制备了十二烷基苯磺酸根(DBS^-)和柠檬酸根(Cit^3-)复合改性层状双氢氧化物(LDHs),简写为DBS-Cit-LDHs。 利用粉末X射线衍射分析、红外光谱分析、比表面积测定以及元素分析等技术手段对样品进行了表征。 结果表明,DBS^-和Cit^3-已柱撑进入LDHs层间。 研究了DBS-Cit-LDHs对水中重金属离子Cu²⁺和有机污染物双酚A(BPA)的协同吸附性能。 吸附实验结果表明,DBS-Cit-LDHs能同时高效去除Cu²⁺和BPA;对Cu²⁺的强吸附能力缘于DBS-Cit-LDHs层间Cit^3-与Cu²⁺形成了稳定配合物;对BPA的强吸附能力缘于分配作用,且吸附能力与样品比表面积无关。 DBS-Cit-LDHs对Cu²⁺的吸附动力学和热力学分别符合准二级动力学方程和Freundlich等温式;对BPA的吸附分别符合准一级动力学方程和Linear等温式。 二者吸附过程的ΔG^o和ΔH^o均为负值,表明吸附为自发放热过程。     

丁二酸酐接枝纤维素纳米纤维膜及其重金属离子吸附

采用热致相分离(TIPS)法以三醋酸纤维素(TCA)为原料成功制备直径为(110±28)nm TCA多孔纳米纤维膜。将TCA纤维膜通过水解转化为纤维素(Cell)、接枝制备丁二酸酐接枝改性纤维素(Cell-g-SAA)膜。将Cell膜和Cell-g-SAA膜用于吸附水中Cu~(2+)、Pb~(2+),并对膜样品的吸附动力学、等温吸附和吸附热力学进行了研究。结果表明,二级动力学拟合和Langmuir模型更适合于该体系。与Cell膜相比,改性后Cell-g-SAA膜对Cu~(2+)和Pb~(2+)的最大吸附容量分别从51.73和34.29 mg/g增加到116.41和51.73 mg/g。纤维膜对Cu~(2+)、Pb~(2+)的吸附更趋近于单层吸附且化学吸附占主导地位。     

磁性碳纳米管表面多金属离子印迹聚合物制备及应用

以磁性碳纳米管为载体,Co~(2+)、Cu~(2+)及Cd~(2+)等多种金属离子为模板和多巴胺为功能单体,研制一种对多种重金属离子具有高选择性吸附性能的磁性离子印迹聚合物(MIIPs)。采用红外光谱仪、透射电子显微镜、扫描电子显微镜和振动样品磁强计等技术手段对MIIPs进行了表征。采用原子吸收光谱详细研究了MIIPs的吸附性能,结果表明,MIIPs不仅具有优异的磁性能,而且对Cu~(2+)、Co~(2+)及Cd~(2+)具有快速、高效的选择识别能力,最大吸附量分别为46.08、36.35和30.65 mg/g。结合磁固相萃取和原子吸收光谱,MIIPs成功用于淤泥中Cu~(2+)、Co~(2+)及Cd~(2+)的同时分离富集,富集因子分别为18.6、13.4以及10.9。     

Tuning plasmon absorption of unmodified silver nanoplates for sensitive and selective detection of copper ions by introduction of ascorbate

Silver nanoplates as novel optical sensors for Cu^2＋ detection have been demonstrated.Silver nanoplates are synthesized via previous H_2O_2-NaBH_4 cyclic oxidation-reduction reactions.With introduction of ascorbate as mild reductants,Cu^2＋ ions are reduced into Cu~＋ and the Cu^＋ is further reduced to Cu,which is deposited on the surface of the silver nanoplates.The deposition of the Cu on the surface of the silver nanoplates allows a significant red-shift of their plasmon absorption.Therefore,trace Cu^2＋ can be detected.The shift of the plasmon absorption wavelength of silver nanoplates is proportional to the Cu^2＋concentration over a range of 40-340 μmol L~（-1） with a limit of detection of 9.0 μmol L~（-1）.Moreover,such silver nanoplate-based optical sensors provide good selectivity for Cu^2＋ detection,and most other metal ions do not disturb its detection.Moreover,the practicality of the proposed sensor was tested.This Cu^2＋assay is advantageous in its simplicity,selectivity,and cost-effectiveness.     

铜离子与SALI3-2蛋白的相互作用

用1/2 MS固体培养基培养拟南芥幼苗, 研究了CuCl₂对转Sali3-2基因植株生长的影响, 发现转基因植株Sali3-2的表达可提高其耐受Cu²⁺胁迫的能力. 进一步克隆Sali3-2基因, 表达并纯化了缺失信号肽的 SALI3-2 蛋白. 利用固定金属离子亲和色谱(IMAC)分析发现, Cu²⁺ 能够与 SALI3-2 蛋白结合. 通过荧光光谱及圆二色光谱(CD)进一步研究了Cu²⁺ 与 SALI3-2 蛋白间的键合机理. 结果表明, Cu²⁺ 可引起SALI3-2 蛋白内源性荧光猝灭, 其猝灭机制为静态猝灭; Cu²⁺ 与SALI3-2 蛋白的结合常数为8.89×10⁶, 结合位点数为1.6. CD分析显示, Cu²⁺ 与SALI3-2 蛋白的结合未使SALI3-2 蛋白二级结构发生明显改变. 由此推测, 在高浓度铜离子胁迫下, SALI3-2蛋白通过结合一定数量的Cu²⁺使蛋白的构象发生改变, 这可能是SALI3-2蛋白的表达使植物耐受Cu²⁺胁迫能力提高的分子机制之一.     

Recycle Adsorption of Cu2+ on Amine-functionalized Mesoporous Silica Monolithic

3-Aminopropyltriethoxysilane functionalized worm-like mesoporous silica monolithic(WMSM-NH₂) was prepared and used as a new regenerable adsorbent for the removal of Cu²⁺ ions. The analysis results show that the WMSM-NH₂ monolithic had a high efficiency value of 99.3% for Cu²⁺ remediation when the Cu²⁺ solution was at an initial concentration of 10.32 mg/L. The regeneration study of the WMSM-NH₂ monolithic presented that the adsorption efficiency of 89.0% was remained and a mass of 92.0% was left after seven adsorption-desorption cycles were executed. The monolithic material with high resistance to the acid and good mechanical stability can facilitate the operations of adsorption and regeneration of the adsorbent.     

The effect of the amount of ammonia on the Cu~0/Cu~+ ratio of Cu/SiO_2 catalyst for the hydrogenation of dimethyl oxalate to ethylene glycol

The effect of the amount of precipitant ammonia on the Cu0/Cu＋ratio of Cu/Si O2 prepared by the deposition–precipitation method is investigated. Species at different preparation stages, resulted from the amount of ammonia used, are identified by the XRD and FTIR techniques. Chrysocolla together with either copper nitrate hydroxide or copper hydroxide coexist in the uncalcined catalysts. Upon calcination, the latter two species are converted to Cu O particles while chrysocolla remains. Following reduction, Cu O is transformed to metallic Cu and chrysocolla is converted to Cu2 O. The value of Cu0/Cu＋ratio can be evaluated using the peak areas in their TPR profiles. Hydrogenation of dimethyl oxalate（DMO） to ethylene glycol（EG） shows that the selectivity of EG depends on the Cu0/Cu＋ratio. Catalyst prepared with the addition of ammonia solution at n（NH3）/n（Cu2＋） = 0.9 for precipitation–deposition gains a more suitable Cu0/Cu＋ratio upon reduction and thus has a higher selectivity for EG.     

Adsorption of Heavy Metal Ions from Aqueous Solutions by Zeolite Based on Oil Shale Ash: Kinetic and Equilibrium Studies

Na-A zeolite was successfully synthesized via the alkaline fusion method with oil shale ash as the raw material. The adsorption capacity of it was tested by removing Cu²⁺, Ni²⁺, Pb²⁺ and Cd²⁺ from aqueous solutions. The results reveal the maximum adsorption capacity of adsorbent for Pb²⁺, Cu²⁺, Cd²⁺ and Ni²⁺ were 224.72, 156.74, 118.34 and 53.02 mg/g, respectively. The effects of contact time and pH value of solutions on the adsorption efficiency of the zeolite were evaluated. Besides, The equilibrium adsorption data and the batch kinetic data were correlated with Langmuir and Freundlich models and the pseudo-first-order and pseudo-second-order models separately. The results show that the Langmuir isotherm and the pseudo-second-order equation were more suitable for the adsorption of Na-A zeolite for the metal ions. In addition, Thermodynamic parameters of the adsorption(the Gibbs free energy, entropy, and enthalpy) were also evaluated and discussed. The results demonstrate that the adsorption process was spontaneous and endothermic under natural conditions and the synthesized zeolite was an effective adsorbent for the removal of metal ions from aqueous solution.