新型二元相MoS2/C纳米管的合成和机理研究

在900 ℃氢气气氛下, 通过热分解载有硫代钼酸铵的碳纳米管前驱物得到MoS₂/C二元相纳米管. 通过粉末X射线衍射(XRD)、高分辨透射电镜(HRTEM)、扫描电镜(SEM)和X射线能量散射仪(EDS)等方法对其形貌、结构和成分进行了表征. 结果表明, 我们合成了一种由两种材料组成管壁的新型纳米管, 并对其形成机理进行了研究.     

脉冲沉积制备Cu2O/TiO2纳米管异质结的可见光光催化性能

在用阳极氧化法制备有序排列TiO₂纳米管阵列薄膜的基础上,引入脉冲沉积工艺,成功实现了均匀、弥散分布的Cu₂O纳米颗粒修饰改性TiO₂纳米管阵列,形成Cu₂O/TiO₂ 纳米管异质结复合材料. 利用场发射扫描电镜（FESEM）、场发射透射电镜（FETEM）、X射线衍射（XRD）、X射线光电子能谱（XPS）和紫外-可见漫反射光谱（UV-Vis DRS）对样品进行表征,重点研究了Cu₂O/TiO₂ 纳米管异质结的光电化学特性和对甲基橙（MO）的可见光催化降解性能. 结果表明,Cu₂O纳米颗粒均匀附着在TiO₂纳米管阵列的管口和中部位置,所制备的Cu₂O/TiO₂ 纳米管异质结具有高效的可见光光催化性能;在浓度为0.01 mol·L^-1的CuSO₄溶液中制得的Cu₂O/TiO₂纳米管异质结表现出最好的电化学特性和光催化性能;另外,对Cu₂O纳米颗粒影响光催化活性的机理进行了讨论.     

溶剂热方法合成Cu2ZnSnS4空心球

以氯化亚铜,硝酸锌,氯化锡和硫脲作为反应前驱体,聚乙二醇作为模板,利用溶剂热方法合成Cu₂ZnSnS₄中空球。其中,聚乙二醇对于产物的最终形成起到关键作用。文章讨论了Cu₂ZnSnS₄中空球的生长机制,并通过X射线衍射(XRD)、拉曼光谱、场发射电子显微镜(FESEM)、透射电子显微镜(TEM)、X射线能量色散谱(EDX)、X射线光电子谱(XPS)、选区电子衍射谱(SAED)和紫外-可见光分光光度计(UV-Vis)等技术对样品的微结构以及光学性质进行了表征和分析。结果显示Cu₂ZnSnS₄中空球为四方晶体,尺寸为600 nm。其禁带宽度为1.52 eV,适用于制作光伏器件。     

溶剂热方法合成Cu2ZnSnS4空心球

以氯化亚铜,硝酸锌,氯化锡和硫脲作为反应前驱体,聚乙二醇作为模板,利用溶剂热方法合成Cu₂ZnSnS₄中空球。其中,聚乙二醇对于产物的最终形成起到关键作用。文章讨论了Cu₂ZnSnS₄中空球的生长机制,并通过X射线衍射(XRD)、拉曼光谱、场发射电子显微镜(FESEM)、透射电子显微镜(TEM)、X射线能量色散谱(EDX)、X射线光电子谱(XPS)、选区电子衍射谱(SAED)和紫外-可见光分光光度计(UV-Vis)等技术对样品的微结构以及光学性质进行了表征和分析。结果显示Cu₂ZnSnS₄中空球为四方晶体,尺寸为600 nm。其禁带宽度为1.52 eV,适用于制作光伏器件。     

LiNi1/3Co1/3Mn1/3O2正极材料的制备与倍率性能研究

在碳酸盐共沉淀法中引入超声波技术,合成锂镍钴锰前驱体,然后通过高温煅烧制备了LiNi_1/3Co_1/3Mn_1/3O₂正极材料,采用扫描电镜(SEM)、X射线能谱(EDS)、X射线衍射(XRD)、差示量热扫描(DSC)、循环伏安法(CV)及充放电测试等手段对材料进行了表征。结果表明,材料在700～1 000 ℃下均能形成六方层状α-NaFeO₂结构,其晶体有序化程度随着煅烧温度的升高而升高。SEM分析     

Z型Ag-Cu2O/BiVO4光催化剂的光催化还原CO2性能

利用简单的化学还原沉积法将 Cu₂O纳米球和 Ag纳米颗粒均匀包裹在十面体 BiVO₄表面,成功构建了一种具有高效电荷载流子分离/转移特性的Z型异质结光催化剂Ag-Cu₂O/BiVO₄。Ag-Cu₂O/BiVO₄在可见光下光催化CO₂还原为CO的产率可达5.37 μmol·g^-1·h^-1,分别是纯 BiVO₄和 Cu₂O的 35.80倍和 6.30倍。通过 X射线粉末衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)、X射线能谱(EDS)、紫外可见漫反射光谱(UV-Vis DRS)、光致发光(PL)光谱、瞬态光电流响应(TPC)和电化学阻抗谱(EIS)对 Ag-Cu₂O/BiVO₄的晶体结构、形貌、组成、能带结构和吸光能力等进行了系统表征分析,并提出了其光催化体系还原CO₂的催化机理。     

Z型Ag-Cu2O/BiVO4光催化剂的光催化还原CO2性能

利用简单的化学还原沉积法将Cu₂O纳米球和Ag纳米颗粒均匀包裹在十面体BiVO₄表面,成功构建了一种具有高效电荷载流子分离/转移特性的Z型异质结光催化剂Ag-Cu₂O/BiVO₄。Ag-Cu₂O/BiVO₄在可见光下光催化CO₂还原为CO的产率可达5.37 μmol·g^-1·h^-1,分别是纯BiVO₄和Cu₂O的35.8倍和6.25倍。通过X射线粉末衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)、X射线能谱(EDS)、紫外可见漫反射光谱(UV-Vis DRS)、光致发光(PL)光谱、瞬态光电流响应(TPC)和电化学阻抗谱(EIS)对Ag-Cu₂O/BiVO₄的晶体结构、形貌、组成、能带结构和吸光能力等进行了系统表征分析,并提出了其光催化体系还原CO₂的催化机理。     

基于铜基底的TiO2纳米管阵列储锂性能

研究了基于铜基底的TiO₂纳米管阵列直接作为锂离子电池电极的储锂性能。以铜基底上生长的Cu(OH)₂纳米棒阵列为模板, 采用自牺牲模板法, 通过外向包覆与内向刻蚀, 制备了非晶态的TiO₂纳米管阵列, 然后将其在500℃下退火处理4 h, 获得锐钛矿型TiO₂纳米管阵列。采用X射线衍射、场发射扫描电镜、透射电镜、热重分析对样品进行表征;采用恒电流充放电、循环伏安和交流阻抗谱测试对退火前后TiO₂纳米管阵列的电化学性能进行研究。结果表明:与非晶态的TiO₂纳米管阵列相比, 锐钛矿型TiO₂纳米管阵列吸附水的含量低, 结晶度高, 电荷迁移阻力小, 锂离子扩散系数大, 结构稳定, 具有更好的循环性能和倍率性能;在0.2 C下, 其首次放电比容量为353 mAh·g^-1, 经过40次循环后的放电比容量仍为243 mAh·g^-1, 在8C下的放电比容量为90 mAh·g^-1。     

Bi2WO6/TiO2纳米管异质结构复合材料的多模式下的光催化活性比较

以TiO₂纳米管为模板,采用多组分自组装结合水热法制备Bi₂WO₆/TiO₂纳米管异质结构复合材料。通过多种技术如X射线衍射（XRD）,X射线光电子能谱（XPS）,N₂吸附-脱附,扫描电镜（SEM）,高分辨透射电镜（HRTEM）和紫外可见漫反射吸收光谱（UV-Vis DRS）考察所制备样品的组成、结构、形貌、光吸收和电子性质。Bi₂WO₆纳米片或纳米粒子分布在TiO₂纳米管上,形成异质结构。随后,通过在紫外、可见和微波辅助光催化模式下降解染料罗丹明B（RhB）来评价复合催化剂的光催化活性。与TiO₂纳米管和Bi₂WO₆相比,Bi₂WO₆/TiO₂-35纳米管在多模式下表现出更优异的光催化活性。与紫外和可见降解模式相比,Bi₂WO₆/TiO₂-35纳米管在微波辅助光催化模式下对RhB的降解效率最高。这种增强的光催化活性源于适量Bi₂WO₆的引入、纳米管独特的形貌特征和降解模式所引起的增强的量子效率。降解过程中的活性物种被证明是h⁺,·OH和·O₂^-自由基。而且,在微波辅助光催化模式下,可产生更多的·OH和·O₂^-自由基。     

Bi2WO6/TiO2纳米管异质结构复合材料的多模式下的光催化活性比较

以TiO₂纳米管为模板,采用多组分自组装结合水热法制备Bi₂WO₆/TiO₂纳米管异质结构复合材料。通过多种技术如X射线衍射（XRD）,X射线光电子能谱（XPS）,N₂吸附脱附,扫描电镜（SEM）,高分辨透射电镜（HRTEM）和紫外可见漫反射吸收光谱（UV-Vis DRS）考察所制备样品的组成、结构、形貌、光吸收和电子性质。Bi₂WO₆纳米片或纳米粒子分布在TiO₂纳米管上,形成异质结构。随后,通过在紫外、可见和微波辅助光催化模式下降解染料罗丹明B（RhB）来评价复合催化剂的光催化活性。与TiO₂纳米管和Bi₂WO₆相比,Bi₂WO₆/TiO₂-35纳米管在多模式下表现出更优异的光催化活性。与紫外和可见降解模式相比,Bi₂WO₆/TiO₂-35纳米管在微波辅助光催化模式下对RhB的降解效率最高。这种增强的光催化活性源于适量Bi₂WO₆的引入、纳米管独特的形貌特征和降解模式所引起的增强的量子效率。降解过程中的活性物种被证明是h⁺,·OH和·O₂^-自由基。而且,在微波辅助光催化模式下,可产生更多的·OH和·O₂^-自由基。     

Investigation on the Growth Mechanism of Cu2MoS4 Nanotube,Nanoplate and its use as a Catalyst for Hydrogen Evolution in Water

Cu₂MoS₄ is a ternary transition‐metal sulfide that shows great potential in the field of energy conversion and storage, namely catalytic H₂ evolution in water and Li‐, Na‐ or Mg‐ion battery. In this work, we report on a growth mechanism of the single‐crystalline Cu₂MoS₄ nanotube from (NH₄)₂MoS₄ salt and Cu₂O nanoparticle. By probing the nature and morphology of solid products generated in function of reaction conditions we find that the crystalline Cu(NH₄)MoS₄ nanorod is first generated at ambient conditions. The nanorod is then converted into Cu₂MoS₄ nanotube under hydrothermal treatment due to the Kirkendall effect or a selective etching of the Cu₂MoS₄ core. Extending the hydrothermal treatment causes a collapse of nanotube generating Cu₂MoS₄ nanoplate. The catalytic activities of these sulfides are investigated. The Cu₂MoS₄ shows superior catalytic activity to that of Cu(NH₄)MoS₄. Catalytic performance of the former largely depends on its morphology. The nanoplate shows superior catalytic activity to the nanotube, thanks to its higher specific electrochemical surface area.     

Low-temperature catalytic preparation of multi-wall MoS<Subscript>2</Subscript> nanotubes

In the catalytic reduction atmosphere of H₂+CH₄+C₄H₄S, the ball-milled precursor (NH₄)₂MoS₄ is heated to 300°C for decomposition. The as-synthesized product is characterized by XRD, SEM, HRTEM, EDX, and BET. The results show that multi-wall MoS₂ nanotubes are obtained. The length of the nanotubes is around 3–5 μm. The diameters of the nanotubes are homogeneous, with an inner diameter of ∼15 nm, an outer diameter of ∼30 nm, and an interlayer (002) d-spacing of 0.63 nm. This catalytic thermal reaction occurring at low temperatures is important for the large-scale preparation of similar transition-metal disulfide nanotubes.     

The electrochemical properties of Li/TEGDME/MoS2 cells using multi-wall carbon nanotubes as a conducting agent

We investigated the first charge–discharge behavior and cycling property of Li batteries using MoS₂ electrodes with multi-wall carbon nanotubes (MWNT) as a conducting agent. The MoS₂ electrode was prepared using MWNT as the conducting agent. The battery gave a high first discharge capacity of 440 mAhg^?1 with a plateau potential region at 1.1 V. The Li/MoS₂ battery using MWNT showed a higher discharge capacity compared to acetylene black. After ten cycles of the battery using MWNT, the discharge capacity decreased to 120 mAhg^?1, which corresponded to 30% of the first discharge capacity. Adding a carbon nanotube into the MoS₂ electrode improved the first discharge behavior, but did not affect the cycling property of the Li/MoS₂ cell.     

含氯离子电解液中二氧化钛纳米管的阳极氧化形成机理及应用

采用电化学阳极氧化的方法,以氯化铵(NH₄Cl)水溶液为电解液,在纯钛表面制备了二氧化钛(TiO₂)纳米管。考察了制备电压、氧化时间、Cl^-浓度和钛基体的退火处理对阳极氧化过程的影响规律,探讨了在含氯离子电解液中纳米管的形成机理,并基于上述含氯离子电解液中纳米管形成机制,通过两步阳极氧化法得到无支撑纳米管薄膜。     

Modeling of the capillary filling of MoS<Subscript>2</Subscript> nanotubes with titanium tetrachloride molecules

The results of molecular-dynamic modeling of the capillary filling of molybdenum disulfide MoS₂ nanotubes with titanium tetrachloride molecules and the structure of the TiCl₄ liquid inside the nanotubes are presented.     

MoS_2/g-C_3N_4复合材料的制备及可见光催化性能

首先在N-甲基吡咯烷酮溶液中超声剥离得到少层的MoS_2,将其与石墨相氮化碳(g-C_3N_4)复合,制得MoS_2/g-C_3N_4复合材料。采用X射线衍射(XRD),扫描电镜(SEM),X射线光电子能谱(XPS),傅里叶变换红外光谱(FTIR),Raman光谱,紫外-可见漫反射吸收光谱(DRS)和光致荧光(PL)技术对复合材料进行表征。可见光下考察MoS_2/g-C_3N_4复合材料光催化降解罗丹明B(Rh B)的活性,结果表明:将少量MoS_2与g-C_3N_4复合可明显提高光催化活性,且1%(w/w)MoS_2/g-C_3N_4复合物的光催化活性最高,可能的原因是MoS_2和g-C_3N_4匹配的能带结构,增大了界面间电荷的传输,降低了光生电子-空穴的复合,进而提高了光催化活性。     

MoS2/g-C3N4复合材料的制备及可见光催化性能

首先在N-甲基吡咯烷酮溶液中超声剥离得到少层的MoS₂,将其与石墨相氮化碳（g-C₃N₄）复合,制得MoS₂/g-C₃N₄复合材料。采用X射线衍射（XRD）,扫描电镜（SEM）,X射线光电子能谱（XPS）,傅里叶变换红外光谱（FTIR）,Raman光谱,紫外-可见漫反射吸收光谱（DRS）和光致荧光（PL）技术对复合材料进行表征。可见光下考察MoS₂/g-C₃N₄复合材料光催化降解罗丹明B（RhB）的活性,结果表明：将少量MoS₂与g-C₃N₄复合可明显提高光催化活性,且1%（w/w）MoS₂/g-C₃N₄复合物的光催化活性最高,可能的原因是MoS₂和g-C₃N₄匹配的能带结构,增大了界面间电荷的传输,降低了光生电子-空穴的复合,进而提高了光催化活性。     

Nanomechanical and nanotribological characterization of multilayer self-lubricating Ti/MoS2/Si/MoS2 nanocoating on aluminium-silicon substrate

Ti/MoS₂/Si/MoS₂ multilayer coating was fabricated by a pulse laser deposition method from a titanium, molybdenum disulphide, and silicon targets, and the coating was deposited in layers on aluminium-silicon substrates, at room temperature. The structural analysis and surface morphology of multilayer Ti/MoS₂/Si/MoS₂ coating were analysed using X-ray diffraction, Raman spectroscopy, and scanning electron microscopy integrated with energy dispersive X-ray spectroscopy. Nanomechanical tests were performed on Ti/MoS₂/Si/MoS₂ coating at small loads of 2000 to 6000 μN to study the effect of load on hardness and Young's modulus. Nanoscratch and nanowear tests were conducted on Ti/MoS₂/Si/MoS₂ coating at a low load of 1000 to 5000 μN and 100 to 500 μN, respectively, to study deformation and failure behaviours of coating/substrate system and also their nanotribological properties. The results show that hardness and Young's modulus of Ti/MoS₂/Si/MoS₂ coating decrease with increase in load. A low friction coefficient of 0.09 to 0.16 was observed, which proves that the Ti/MoS₂/Si/MoS₂ coating possesses self-lubricating property. The wear rate of Ti/MoS₂/Si/MoS₂ coating increases 3.3 × 10⁻¹⁰ to 7.8 × 10⁻¹⁰ mm³/Nm with increase in load. Ti/MoS₂/Si/MoS₂ multilayer coating shows a smooth wear track with no cracks and debris on the surface, which attributed plastic flow of softer coating material around the wear track.     

C/g-C3N4/MoS2复合材料的制备及光催化性能

首先以尿素和葡萄糖为前驱体,通过热缩合方法制备了C/g-C₃N₄,然后利用溶剂热法合成C/g-C₃N₄/MoS₂三元复合材料。通过不同的手段对其进行了表征,结果表明,与C/g-C₃N₄相比,该三元复合材料不仅具有更强的光吸收性能和更大的表面积,而且更有利于电子的转移。同时对其可见光催化降解甲基橙性能进行研究,结果发现,C/g-C₃N₄/MoS₂-2.0%复合材料(含有质量分数为2.0%的MoS₂)表现出最高的反应速率常数(0.0086 min^-1),分别为g-C₃N₄/MoS₂-2.0%(0.0015 min^-1)和C/g-C₃N₄(0.0036min^-1)的5.7倍和2.3倍。     

Synthesis, characterization and hydrogen storage capacity of MS2 (M = Mo, Ti) nanotubes

The structure, morphology and hydrogen-storage capacity of MS₂ (M = Mo, Ti) nanotubes prepared by different experimental methods were studied. It was found that the MoS₂ nanotubes treated by KOH displayed the gaseous storage capacity of 1.2 wt% hydrogen (under the hydrogen pressure of 3 MPa and 25°C) and the electrochemical discharge capacity of 262 mAh/g (at the discharge current density of 50 mA/g and 25°C) that corresponds to about 1.0 wt % hydrogen. In comparison, TiS₂ nanotubes can store 2.5 wt% hydrogen under the hydrogen pressure of 4 MPa and 25°C. The results show that MS₂ compound nanotubes are promising materials for hydrogen storage. __________ Translated from Acta Scientiarum Naturalium Universitatis Nankaiensis, 2005, 38(4) (in Chinese)