Serially coupled capillary columns supercritical fluid chromatography with a coupling restrictor.

A serially coupled column system for capillary supercritical fluid chromatography was constructed by connecting two capillary columns of different polarities using or without using a coupling restrictor. The influence of the column sequence, the size of the coupling restrictor and the column temperature on the polarity of the system were studied. The system without a coupling restrictor (the directly coupled system) provided an intermediate polarity between two columns, depending on the column geometry, such as the film thickness and column length, although it slightly shifted to that of the first column. In the system with a coupling restrictor, the contribution of the second column to the overall retention increased with its resistance. The use of a coupling restrictor allowed to control the polarity of the coupled system virtually over the whole range between two columns. The temperature was an additional effective parameter for tuning the polarity of the system.     

Supercritical fluid chromatography with a slurry-packed capillary column

A versatile system with a slurry-packed capillary column was developed for supercritical fluid chromatography, which is capable of programming both inlet and outlet pressure independently, as well as using a restrictor to apply back pressure. This system revealed the relationships between pressure drop, flow rate, and linear velocity in pressure-programmed supercritical fluid chromatography. In the restrictor system, both the pressure drop and the flow rate increased almost linearly with inlet pressure, while under conditions of constant pressure drop characteristic behavior was observed which depended on the density-viscosity relationships of supercritical fluid. Resolution in the separation of polysiloxane oligomers was found to be increased by increasing the ratio of pressure drop to pressure-programming rate, although the sensitivity decreased due to the increase in peak volume. The system controlling both inlet and outlet pressure has distinct advantages over the restrictor system controlling both inlet and outlet pressure has distinct advantages over the restrictor system in practical in practical operations.     

Direct coupling of capillary supercritical fluid chromatography to high resolution mass spectrometry with minimum modification

Summary The coupling of a capillary supercritical fluid chromatograph with a high resolution double focusing mass spectrometer has been accomplished without any modifications to the pumping or ion source systems. The interface utilizes a direct insertion probe (DIP), which was originally designed for the direct analysis of solid samples, together with a trit restrictor as a decompression device. The DIP is placed opposite to the SFC restrictor, and it provides sufficient heat to prevent cluster formation and cooling resulting from the expansion of the supercritical fluid into the vacuum environment. Excellent mass spectra of standard polycyclic aromatic hydrocarbons under chemical-ionization (CI) conditions using methane as the reagent gas, and under charge-exchange (CE) conditions using CO₂ as the charge exchange medium were obtained.     

Study of photopolymers. XXXIII. Chemical modification of poly(epichlorohydrin) and its application as photosensitive polymers

High Tg. polymers containing both vinyloxy moiety and pendant phthalyl, 2-thiobenzoxazole or 2-thiobenzothiazole groups were synthesized by elimination reaction of poly(epichlorohydrin) with potassium hydroxide followed by substitution reaction of the obtained polymer with potassium phthalimide, potassium 2-thiobenzoxazole or potassium 2-thiobenzothiazole using tetrabutylammonium bromide as a phase transfer catalyst. The polymers containing vinyloxy moiety and pendant phthalyl or 2-thiobenzothiazole groups showed high photochemical reactivity and excellent practical photosensitivity as a positive type resist with photo-generated cationic catalyst such as 2,5-dibutoxy-4-morpholinobenzene diazonium hexafluoroanthimonate. On the other hand, the polymers had high practical photosensitivity and good resolution as a negative type resist with 2,6-di-(4′-azobenzal)-4-methylcyclohexanone as a photosensitizer.     

Evaluation of flow restrictors for open-tubular supercritical fluid chromatography at pressures up to 560 atm

Proper performance of the flow restrictor is of crucial importance in supercritical fluid chromatography. This is especially the case when the restrictor is the interface between the chromatographic column and a detector operating at lower pressure than the column. The performance of three types of fixed flow restrictor, the “tapered”, the “integral”, and the “frit”, was examined. The test mixtures chosen covered a range of polarities and molecular weights. Polydimethylsiloxane with an average molecular weight of 10,000 was used as a low polarity probe. Two polyethylene glycol mixtures were chosen as higher polarity probes. One consisted of a mixture of polyethylene glycol standards with average molecular weights ranging from 200 to 1450. The other polyethylene glycol mixture had an average molecular weight of 2000. The polydimethylsiloxane standard did not elute when the frit restrictor was used. Satisfactory results were obtained when the tapered and integral restrictors were employed. All three restrictors provided satisfactory results for polyethylene glycol oligomers eluting up to approximately 40.5 MPa (400 atm). However, for oligomers eluting above this pressure, the peaks merged into a broad hump with the frit restrictor, while the tapered and integral restrictors provided satisfactory separations. The integral restrictor produced more evenly spaced, more well resolved peaks at the high-pressure end of the chromatograms than did the tapered restrictor. This is shown to be due to differences in the rates of increase in mobile-phase velocity with increasing pressure for the two restrictors.     

Synthesis, characterization and properties of naphthoxazine-functional poly(propyleneoxide)s

Thermally curable naphthoxazine-functionalized polymers were synthesized by the reaction of linear (diamines) and branched (triamines) poly(propyleneoxide)s (Jeffamine series) having various molecular weights, with p-formaldehyde, and 2-naphthol. The structures of the resulting polymers were characterized by using FT-IR and ¹H-NMR. In addition, curing behavior of these polymers was studied using differential scanning calorimeter (DSC). Hydrophilicity of these polymers, both in cured and non-cured states, was investigated by water contact angle measurements. The surface topographies of the polymers were also examined by atomic force microscope (AFM).     

HPLC-FID with Superheated Water as the Eluent: Improved Methods and Instrumentation

In the current study, an HPLC-FID system using superheated water as the eluent is constructed and further improved. Signal stability during temperature programmed operation was improved by using separate thermostatting of the 50 μm capillary restrictor. Operating the restrictor at 75°C prevented the superheated water from sputtering in the restrictor. Conventional octadecyl-modified silica, thermostable polymeric reversed phase and carbon type HPLC columns were used. The feasibility of the system is demonstrated by the analysis of a variety of compounds such as alcohols and aldehydes. It is shown that increased temperatures decrease elution times and, in addition to this, frequently improve peak shapes and column efficiencies. The separation of lower aldehydes is performed at 175°C with a detection limit in the low μg/ml range. The possibility of temperature programming is demonstrated for the separation of a range of alcohols. Furthermore, it is shown that temperature programming can be used for sample enrichment. Large volume injection with low temperature enrichment resulted in good peak shapes and a significant improvement of the detection limit. In this way, detection limits of 0.2 μg/ml (ppm) could be obtained for the aldehydes studied. Finally, the possibilities of using mobile phase additives as, e.g., buffers were briefly examined.     

Chromatography with dense gases

Summary A capillary restrictor for supercritical fluid chromatography (SFC) with CO₂ was made by using a micro torch and fine emery cloths or grinding blocks. This restrictor could be drawn out either directly from the end of the analytical capillary column, or from a short piece of any capillary, which was then connected to the analytical column by standard techniques. It was found that the base current of a flame ionisation detector (FID) depends strongly on the position of the capillary end with respect to the FID flame tip and on the CO₂ grade, of course. Best results have been achieved at around 5 to 7 mm distance between the restrictor and the flame tip ends, and using SFC grade CO₂.     

Modification of polymers via electrophilic aromatic substitution

Three vinyl monomers, 2,4,6-trimethoxystyrene, 4-(N,N-dimethylamino)styrene, and N-methyl-2-vinylpyrrole, were synthesized via the Wittig reaction from the corresponding aldehyes. These monomers were homopolymerized by radical polymerization using α,α′-azoisobutyronitrile (AIBN) as initiator at 60°C. The reaction of these polymers with 4-phenyl-1,2,4-triazoline-3,5-dione (phTD) and 4-methyl-1,2,4-triazoline-3,5-dione (MeTD) was investigated. Although polytrimethoxystyrene reacts slowly with PhTD at room temperature, the other two polymers react fast and lead to the incorporation of the triazolinedione unit into the side chain of the polymer via electrophilic aromatic substitution. The reaction of bistriazolinediones (BTD) with these polymers was performed in dimethylformamide using 10–20% molar concentration of the BTD. The resulting crosslinked polymers are insoluble in polar as well as nonpolar solvents. Some physical properties of the unmodified and modified polymers were studied.     

Serially coupled capillary columns supercritical fluid chromatography with midpoint pressure control

Two capillary columns of different polarities were coupled in series by means of a coupling restrictor. The pressure of the first column and the midpoint pressure (between the coupling restrictor and the second column) were controlled independently of each other using two pumps. The selectivity of this separation system was highly dependent on the pressure difference and could be continuously changed between those of two columns. The pressure difference could be changed even in course of separation for fine tuning of the selectivity. Several examples were shown to demonstrate the utility of this method.     

Capillary and packed column SFC/MS

A frit restrictor interface for capillary column supercritical fluid chromatography/mass spectrometry (SFC/MS) has been constructed and used for the analysis of high boiling point alkanes. Packed column SFC/MS is described using both a moving belt liquid chromatographic/mass spectrometric interface and a thermospray source in the filament-on mode.     

A versatile method for cyclic polymers from conjugated and unconjugated vinyl monomers

A versatile method was introduced to prepare cyclic polymers from both conjugated and unconjugated vinyl monomers. It was developed on the combination of the RAFT polymerization and the self‐accelerating double strain‐promoted azide‐alkyne click (DSPAAC) reaction. In this approach, a switchable chain transfer agent 1 was designed to have hydroxyl terminals and a functional pyridinyl group. The protonation and deprotonation of pyridinyl group endowed the chain transfer agent 1 with a switchable control capability to RAFT polymerization of both conjugated and unconjugated vinyl monomers. Based on this, RAFT polymerization and the following hydroxyl end group modification were used to prepare various azide‐terminated linear polymers including polystyrene, poly(N‐vinylcarbazole), and polystyrene‐block‐poly(N‐vinylcarbazole). Using sym‐dibenzo‐1,5‐cyclooctadiene‐3,7‐diyne (DBA) as small linkers, the corresponding cyclic polymers were then prepared via the DSPAAC reaction between DBA and azide terminals of the linear precursors. Due to the self‐accelerating property of DSPAAC reaction, this bimolecular ring‐closing reaction could efficiently produce the pure cyclic polymers using excess molar amounts of DBA to linear polymer precursors. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 1811–1820     

Functionalization of polypropylene by hydroboration

This article relates to functionalized polypropylene with high molecular weight and high crystallinity. The chemistry involves the hydroboration of poly(propylene-co-1,4-hexadiene) with borane reagents, such as diborane and 9-BBN. In turn, the borane-containing polymers are very versatile and can be easily converted to various functionalized polymers under mild reaction conditions. Despite the heterogeneous reaction conditions, both hydroboration and interconversion reactions were very effective using appropriate solvents. Apparently, the double bonds in the side chains are located in the amorphous phase and are ready for reaction with reagents. Overall, this functionalization process preserves the molecular weight and most of the crystallinity of poly(propylene-co-1,4-hexadiene). © 1993 John Wiley & Sons, Inc.     

Parabanic polymers obtained by the cyclocondensation reaction of polyureas containing 2,6-pyridyl structure

The polymers containing 1,3-imidazolidine-2,4,5-trione rings on the macromolecular backbone are known for a few years and named poly(parabanic acid)s. The paper presents some polymers and model compounds with urea and/or parabanic structures, as a result of the cyclocondensation reaction of the urea derivatives containing 2,6-pyridyl rest, with the oxalyl chloride. The 2,6-pyridyl radical has an acid acceptor character that determines an important distinct influence on the cyclocondensation reaction. The influence of the reaction conditions (temperature, time, beside of the presence or absence of pyridine (Py)) on the progress of the cyclocondensation was studied. The advance of the reaction was followed by IR spectra. The products were characterized by the elemental analysis, ¹H NMR and IR spectra, solubilities and viscosity measurements. Thermal properties were determined by thermogravimetric analyses and differential scanning calorimetry. The analytical and spectral data demonstrated that, in absence of Py, the cyclocondensation performed almost completely only in the case of the aliphatic polyureas, while, in the same conditions, the aromatic polymers were only partly transformed. By using the Py as catalyst, both aromatic and aliphatic polyureas can be transformed into parabanic polymers at above 90% transformation degree (TD). A calculation method of the TD based on the IR spectroscopy was discussed.     

Dynamic control of split flow in packed column supercritical fluid chromatography using dual resistively heated restrictors

Remote control of the vent/detector split flow ratio in packed column supercritical fluid chromatography (pSFC) with flame ionization detector (FID) is demonstrated using a dual heated restrictor method. Restrictors stemming from a Tee at the separation column outlet were, respectively, fixed into an FID and a vent port, and their individual temperatures were controlled using resistively heated wires. Subsequently, both system pressure and split flow could be manipulated. For example, for applied restrictor temperatures examined up to 600°C, corresponding vent/FID split flow ratios between 2 and 7 were observed depending on the port heated. As well, column pressures around 16–23 MPa were also achievable over the same range. Conversely, isobaric altering of the split flow ratio was possible when opposing positive and negative temperature gradients were applied at the two restrictors. Under these conditions, the system pressure varied less than 1% RSD over a 10 min period. As an application, the method was used to establish stable detector operation in the analysis of n‐alkanes under pSFC‐FID conditions that initiated flame instability. Results indicate that this technique could be a relatively simple and inexpensive means of controlling system pressure and detector split flow ratios in pSFC‐FID.     

Synthesis and characterization of water-soluble PEGylated lignin-based polymers by macromolecular azo coupling reaction

Water-soluble PEGylated lignin polymers were efficiently synthesized by macromolecular azo coupling reaction between alkali lignin and PEG based macromolecular diazonium salts in alkaline water.     

聚二乙烯苯的取代反应研究

以悬浮聚合法制得一系列高交联聚二乙烯苯树脂，通过改变反应试剂、催化剂、反应溶剂考察了聚二乙烯苯树脂进行亲电取代反应的规律．结果表明，聚二乙烯苯树脂可发生亲电取代反应，反应程度较低．聚（对－二乙烯苯）的反应程度高于聚（间－二乙烯苯）．     

Preparation of new microgel polymers and their application as supports in organic synthesis

A series of soluble microgel polymers have been synthesized using solution-phase polymerization reactions. In a systematic manner, several variables such as monomer concentration, cross-linker content, reaction solvent and reaction time were examined, and this provided an optimal polymer with both solubility and precipitation characteristics suitable for synthetic applications. Thus, a chemically functionalized microgel polymer was synthesized, and the utility of this polymer in the synthesis of a small array of oxazole compounds has been demonstrated. The advantage of the microgel polymers produced was that they exhibited solution viscosities lower than those of conventional linear polymers even at higher concentrations, and this was found to be beneficial for their precipitation properties. Compounds prepared using the described microgel polymer supports were obtained in similar yields and purity when compared with insoluble resins, and more importantly, the soluble polymer bound intermediates could be analyzed at each step using standard NMR techniques.     

Thermal and autoxidation reactions of poly-3-methylenecyclobutene and poly-1-methyl-3-methylenecyclobutene

The thermal ring-opening reactions, autoxidation and hydrogenation of polymethy-lenecyclobutene (PMCB) and poly-1-methyl-3-methylenecyclobutene (PMMCB), were investigated. Both polymers were prepared by cationic polymerization and consisted almost entirely of 1,5-repeating units containing cyclobutene rings in the polymer backbone. Both polymers showed well behaved exothermic processes at elevated temperatures which apparently resulted in crosslinking. These processes were investigated by differential scanning calorimetry and interpreted to involve thermal ring-opening reactions. Autoxidation occurred very rapidly in PMCB but much more slowly in PMMCB as predicted by Bolland's rules. Attempts to hydrogenate the cyclobutene rings in both polymers resulted in the occurrence of hydrogenolysis in PMCB and little or no reaction with PMMCB for a Pd-catalyzed reaction and partial hydrogenation of the latter for a diimide reaction.     

Designing polymer topology by electrostatic self‐assembly and covalent fixation

A novel methodology (electrostatic self‐assembly and covalent fixation) has been proposed for designing unusual polymer topologies such as star polymers, polymacromonomers, dumbbell‐shaped polymers as well as model network polymers. Thus new telechelic polymers having moderately strained cyclic onium salt group as single or both end groups were prepared and subjected to an ion‐exchange reaction to introduce multifunctional carboxylate anions as a counter‐anion. The electrostatically self‐assembled products were then subjected, either directly or after subsequent manipulation, to heat treatment to convert the ionic interaction into the covalent linkage by the ring‐opening reaction to produce a variety of topologically unique polymer architectures in high yields.