Effect of poly(butylene succinate) crystals on spherulitic growth of poly(ethylene oxide) in binary blends of the two substances

The effects of the lamellar growth direction, extinction rings, and spherulitic boundaries of poly(butylene succinate) (PBSU) on the spherulitic growth of poly(ethylene oxide) (PEO) were investigated in miscible blends of the two crystalline polymers. In the crystallization process from a homogeneous melt, PBSU first developed volume‐filling spherulites, and then PEO spherulites nucleated and grew inside the PBSU spherulites. The lamellar growth direction of PEO was identical with that of PBSU even when the PBSU content was about 5 wt %. PEO, which intrinsically does not exhibit banded spherulites, showed apparent extinction rings inside the banded spherulites of PBSU. The growth rate of a PEO spherulite, G_PEO, was influenced not only by the blend composition and the crystallization temperature of PEO, but also by the growth direction with respect to PBSU lamellae, the boundaries of PBSU spherulites, and the crystallization temperature of PBSU, T_PBSU. The value of G_PEO first increased with decreasing T_PBSU when a PEO spherulite grew inside a single PBSU spherulite. Then, G_PEO decreased when T_PBSU was further decreased and a PEO spherulite grew through many tiny PBSU spherulites. This behavior was discussed based on the aforementioned factors affecting G_PEO. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 539–547, 2009     

Effects of amorphous poly(vinyl acetate) on crystalline morphology of poly(3-hydroxybutyric acid-co-3-hydroxyvaleric acid)

The amorphous and crystalline phase behavior, spherulite morphology, and interactions between amorphous poly(vinyl acetate) (PVAc) and poly(3-hydroxybutyric acid-co-3-hydroxyvaleric acid) (PHBV) were examined using differential scanning calorimetry, polarized-light optical and scanning electron, atomic-force microscopy (DSC, POM, SEM, AFM), and small-angle X-ray scattering (SAXS). The PHBV/PVAc blend was found to be miscible with an almost linear T _g-composition relationship, indicating perfect homogeneity. Interaction parameter by melting point depression is a negative value of χ = −0.32, suggesting quite favorable interaction strength. With the intimate interaction between the amorphous PVAc and crystalline PHBV polymers, effects of PVAc on the spherulitic morphology of PHBV are quite significant. Owing to the higher T _g of PVAc (than that of PHBV), the spherulite growth rate of PHBV was depressed by increasing PVAc content in blends. Neat PHBV exhibits ring-banded spherulites when crystallized at T_c = 60 ~ 110^° C {T_{\rm{c}}} = {6}0\sim {11}0^\circ {\hbox{C}} ; however, with increasing PVAc content in the blends, the temperature range at which the PHBV/PVAc blends exhibit ring-banded spherulites remains similar but the regularity increases, and the inter-ring spacing significantly decreases. In addition, the spherulite size and ring-band patterns therein are strongly dependent on T _max (190 vs. 220 °C, respectively, for erasing prior nuclei), from which the blends were quenched to a T _c (60–110 °C) for crystallization. For PHBV/PVAc blends crystallized at the same T _c from different T _max, higher T _max tends to erase nuclei, leading to larger spherulites. However, such larger spherulites owing to higher T _max are not necessarily packed with thicker lamellae.     

Miscibility enhancement and formation of interpenetrating spherulites in ternary blends of crystalline polymers

Miscible blends of three crystalline polymers, namely poly(butylene succinate) (PBS), poly(ethylene succinate) (PES), and poly(oxyethylene) (POE), exhibited interpenetrating spherulites, where a spherulite of one component grows inside the spherulites of other components. PBS and PES were immiscible above the melting points, T_m, of these substances, while ternary blends with POE showed miscibility, which depended on the molecular weight of POE. PBS and PES exhibited the same spherulitic growth process as in a miscible binary blend when they were crystallized from a homogeneous ternary melt. Spherulites of PBS, which is the highest‐T_m component, filled the whole volume first when a miscible ternary blend was quenched below T_m of POE, the lowest‐T_m component. Then, the blends showed either two types of crystallization processes. One was successive nucleation and growth of PES and POE spherulites, that is, PES nucleated and developed spherulites inside the PBS spherulites and then POE spherulites grew inside the interlocked spherulites of PBS and PES. The other was simultaneous growth and the formation of interpenetrating spherulites of PES and POE inside the PBS spherulites. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 706–711, 2010     

Complex phase behavior and state of miscibility in Poly(ethylene glycol)/Poly(l‐lactide‐co‐ε‐caprolactone) Blends

A miscibility and phase behavior study was conducted on poly(ethylene glycol) (PEG)/poly(l ‐lactide‐ε‐caprolactone) (PLA‐co‐CL) blends. A single glass transition evolution was determined by differential scanning calorimetry initially suggesting a miscible system; however, the unusual T_g bias and subsequent morphological study conducted by polarized light optical microscopy (PLOM) and atomic force microscopy (AFM) evidenced a phase separated system for the whole range of blend compositions. PEG spherulites were found in all blends except for the PEG/PLA‐co‐CL 20/80 composition, with no interference of the comonomer in the melting point of PEG (T_m = 64 °C) and only a small one in crystallinity fraction (X_c = 80% vs. 70%). However, a clear continuous decrease in PEG spherulites growth rate (G) with increasing PLA‐co‐CL content was determined in the blends isothermally crystallized at 37 °C, G being 37 µm/min for the neat PEG and 12 µm/min for the 20 wt % PLA‐co‐CL blend. The kinetics interference in crystal growth rate of PEG suggests a diluting effect of the PLA‐co‐CL in the blends; further, PLOM and AFM provided unequivocal evidence of the interfering effect of PLA‐co‐CL on PEG crystal morphology, demonstrating imperfect crystallization in blends with interfibrillar location of the diluting amorphous component. Significantly, AFM images provided also evidence of amorphous phase separation between PEG and PLA‐co‐CL. A true T_g vs. composition diagram is proposed on the basis of the AFM analysis for phase separated PEG/PLA‐co‐CL blends revealing the existence of a second PLA‐co‐CL rich phase. According to the partial miscibility established by AFM analysis, PEG and PLA‐co‐CL rich phases, depending on blend composition, contain respectively an amount of the minority component leading to a system presenting, for every composition, two T_g's that are different of those of pure components. © 2013 Wiley Periodicals, Inc. J. Polym. Sci. Part B: Polym. Phys. 2014 , 52, 111–121     

Crystalline morphology of a thermotropic aromatic polyester crystallized from nematic melt

The crystalline morphology of a thermotropic aromatic polyester crystallized from a nematic melt was investigtated by means of polarized optical microscopy (POM) and scanning electron microscopy (SEM). Due to POM measurements it was found that spherulites of two different types are formed within the two different temperature regions. When T_c was exceeding 170°C, spherulites of type‐1 showing a negative birefringence grew with a radial fibrillar morphology and exhibited a clear Maltese‐cross pattern. The radius growth rate of type‐1 spherulites was about 2.2 μm/min at 185°C. When T_c was smaller than 160°C, spherulites of type‐2 were formed and exhibited a radially outward growing structure but no evident Maltese‐cross pattern. These spherulites could be seen by the naked eyes due to their size reaching several millimeters. SEM observations revealed that the spherulites of type‐1 exhibited a ripple‐like homocentric morphology with periodical compact fibrils having a diameter of about 150 nm perpendicular to the radial direction. In contrast, the spherulites of type‐2 exhibited, as apparent from performed SEM images, radially growing crystallites of about 500 nm in size with no periodicity in the radial direction.     

Periodic extinction bands composed of all flat‐on lamellae in poly(dodecamethylene terephthalate) thin films crystallized at high temperatures

Using in‐house synthesized poly(dodecamethylene terephthalate) (P12T) as a model, periodic extinction‐banded spherulites melt‐crystallized at high T_cs (100–115 °C) are expounded in terms of growth mechanism. The extinction‐banded spherulites wildly differing from the usual blue/orange double ring‐banded spherulites are composed of all flat‐on discrete single‐crystalline lamellae packed like roof shingles (or fish scales) along the circularly curved bands and the lamellae in the extinction bands are flat with a lozenge shape with no continuous twisting at all. For P12T films of more than 10 µm crystallized at T_c = 105–115 °C, no periodic bands were seen, and all spherulites were ringless, where periodic growth precipitation of crystals to extinction does not occur until impingement. Extinction bands in the P12T spherulites with the inter‐ring spacing steadily decrease with decreasing film thickness, because for thinner films (submicrons to 2 µm), draining or depletion of available molten species takes place more frequently, leading to bands of smaller inter‐ring spacing. The petal‐like extinction bands are discussed and analyzed in detail using 3D AFM imaging. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 601–611     

Relationship between Localization of PBSU in Interlamellar/Interfibrillar Regimes and Double Peaks in DSC/SAXS in its Blend with PVDF

In this work, phase segregation and localization of PBSU have been investigated with the combination of SAXS and DSC in its blend with PVDF. After stepwise crystallization of PVDF and PBSU, there are double melting peaks of PBSU in DSC and double scattering peaks in SAXS. It has been demonstrated that double peaks can be attributed to the localization of PBSU in interlamellar/interfibrillar region in pre-formed PVDF crystal framework. In the case of low content of PBSU in blend, PBSU is trapped into the interlamellar region of PVDF crystals, resulting in the alternating lamellae crystal of them and the first peak (with low-q) in SAXS. The enhanced confinement effect produces thinner PBSU lamellae, corresponding to the lower melting temperature in DSC. Upon increasing its content in blend, some PBSU segregates in interfibrillar regions in addition to the enrichment in interlamellar regions of PVDF crystal framework. The larger space and higher concentration of PBSU in interfibrillar-regions contribute to periodic lamellae structure of PBSU with higher thickness, which is the reason for the second peak (with high-q) in SAXS and DSC. Our results not only clarify the relationship between localization of PBSU in interlamellar/interfibrillar regions and double peaks in DSC/SAXS, but also provide a novel strategy to detect the interlamellar and interfibrillar segregation of low-T_m component in miscible crystalline/crystalline blend.

     

Correlation of crack patterns and ring bands in spherulites of low molecular weight poly(<Emphasis Type="SmallCaps">l</Emphasis>-lactic acid)

Only a single type of circular circumferential crack is conventionally reported for poly(l-lactic acid) (PLLA). In this study, PLLA samples were found to exhibit as many as four crack types of different directions and patterns, which cannot be feasibly explained simply by the directional difference in coefficients of thermal expansion. Depending on crystallization temperature (T _c), PLLA crystallizes into ringless or ring-banded spherulites, whereas the crack patterns are dramatically different in these two types of spherulites. In ring-banded spherulites of PLLA crystallized at intermediate T _c, two uniquely different crack types are present: (1) twin circumferential cracks coinciding with the dark–bright and bright–dark boundary and (2) radial short-segmental voids coinciding on the bright bands in spherulites. The radial short-segmental cracks on the bright band of ring-banded spherulites may be caused by PLLA crystals of radial direction with various twisting that contract laterally upon cooling. Only circumferential cracks are present in PLLA crystallized into ringless spherulites, where concentric continuous circumferential cracks are present in the ringless spherulites at low T _c with finer lamellae, but discontinuous and irregular circumferential cracks are present in the ringless spherulites at high T _c with coarse lamellae. Although all cracks are triggered by cooling from T _c, all evidences indicate that the crack patterns and types are highly associated with the lamellar orientation, patterns, and coarseness in spherulites.     

Effects of top confinement and diluents on morphology in crystallization of poly(l‐lactic acid) interacting with poly(ethylene oxide)

Effects of top confinement and diluent poly(ethylene oxide) (PEO) on poly(l ‐lactic acid) (PLLA) crystal morphology have been investigated. When crystallized at 120 °C, uncovered neat PLLA sample exhibits higher growth rate ringless spherulites; while the covered sample exhibits lower growth rate ring‐banded spherulites. As PEO is introduced into PLLA, the morphology also undergoes significant changes. For the same T_c,PLLA = 120 °C, the PEO/PLLA blend with PEO composition greater than 25% exhibits ring‐banded patterns even in uncovered sample. However, in much greater PEO composition (>80 wt %), uncovered samples exhibit ring bands diverging into dendritic patterns, while top covered samples tend to maintain the spiral ring‐band patterns. Both PEO inclusion in PLLA and top cover on films impose growth kinetic alterations. Additionally, the top glass cover tends to prevent the lower surface tension PLLA to be accumulated on the surface, resulting in the formation of ring‐band pattern. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1160–1170     

Investigations of the equilibrium melting temperature in PBT and PC/PBT blends

The melting behavior of poly(butylene terephthalate) and its blends with bisphenol-A polycarbonate was investigated with differential scanning calorimetry. The aim of this work was to determine the equilibrium melting temperature and its dependence on the blend composition using the Hoffman-Weeks plots. It is shown that the critical analysis of various influences on the melting peak is necessary for the reorganization processes and crystallized content of blends. The experimental conditions and the corrections of measured temperatures were derived and discussed. It was found that the use of the extrapolated onset temperature T_m,o of the melting peak is more efficient than the maximum temperature T_m for the Hoffman-Weeks plots. The equilibrium values of pure PBT are determined to be T^o_m,o = 501 K and T^o_m = 506 K. The equilibrium temperatures of the blends do not show a depression with increasing PC content. Using the Nishi-Wang relation, the results can be qualitatively interpreted with a polymer-polymer interaction coefficient χ ≥ 0 between both components. A weak increase in the equilibrium temperature with increasing PC content was observed. A hypothesis to explain this is based on the possibility of a changed population of the different spherulites with various melting temperatures in dependence on PC content. © 1996 John Wiley & Sons, Inc.     

Lamellar assembly corresponding to transitions of positively to negatively birefringent spherulites in poly(ethylene adipate) with phenoxy

Surface morphology of positively or negatively birefringent spherulites in melt-crystallized neat poly(ethylene adipate) (PEA) vs. PEA blend with phenoxy was examined using atomic force microscopy (AFM), scanning electron microscopy, polarizing optical microscopy, thermal analysis, and wide-angle X-ray techniques. Their top-surface morphology in thin film forms was analyzed to fully expounded the lamellar assembly responsible for the opposite birefringence. Top-surface lamellar assemblies in positive/negative types of ringless spherulites (T _c = 0, 15, 20, 40 °C) and also alternating birefringence of double-ring-banded spherulite (T _c = 28 °C) of PEA/phenoxy blend were examined with AFM. From the results, spherulite’s positive and negative birefringence differs only in interior lamellar arrangements but not lattice geometries. Negative spherulites are composed of radially oriented edge-on lamellae, while positive spherulites are composed of bending/coiling edge-on lamellae. By contrast, the ring-banded spherulites can exhibit both negative and positive birefringence depending on the alternating radial and tangential lamellar arrangement. The addition of phenoxy into PEA could disrupt the regular lamellar bending and promote the singularity of edge-on lamellae; owing to that, the amorphous phenoxy induces looser arrangement of edge-on lamellae with phenoxy being in interlamellar/interfibrillar regions. The bulky linking pendent group phenoxy, with H-bonding capacity interacting with PEA, also disrupts the regularity of tangential–radial PEA lamellae to display a more zigzag pattern.     

Crystallization behavior and morphology of poly(propylene terephthalate) copolymers containing neopenthyl glycol moieties

The melting behavior and the crystallization kinetics of random poly(propylene/neopenthyl terephthalate) copolymers (PPT‐PNT) were investigated by means of differential scanning calorimetry and hot‐stage optical microscopy. Multiple endotherms were evidenced in the PPT‐PNT samples, due to melting and recrystallization processes, similarly to PPT. By applying the Hoffman‐Weeks' method, the T_m° of the copolymers was derived. Baur's equation described well the T_m‐composition data. The isothermal crystallization kinetics was analyzed according to the Avrami's treatment. The introduction of NT units decreased the crystallization rate in comparison to pure PPT. Values of the Avrami's exponent close to three were obtained in all cases, regardless of T_c, in agreement with a crystallization process originating from predeterminated nuclei and characterized by three dimensional spherulitic growth. As a matter of fact, space‐filling spherulites were observed by optical microscopy at all T_cs. Banded spherulites were found for PPT‐PNT5 and PPT‐PNT10, the band spacing being affected by both T_c and composition. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 818–830, 2008     

Investigation on LCST behavior of a new amorphous/crystalline polymer blend: Poly(n‐methyl methacrylimide)/poly(vinylidene fluoride)

The liquid–liquid phase‐separation (LLPS) behavior of poly(n‐methyl methacrylimide)/poly(vinylidene fluoride) (PMMI/PVDF) blend was studied by using small‐angle laser light scattering (SALLS) and phase contrast microscopy (PCM). The cloud point (T_c) of PMMI/PVDF blend was obtained using SALLS at the heating rate of 1 °C min^?1 and it was found that PMMI/PVDF exhibited a low critical solution temperature (LCST) behavior similar to that of PMMA/PVDF. Moreover, T_c of PMMI/PVDF is higher than its melting temperature (T_m) and a large temperature gap between T_c and T_m exists. At the early phase‐separation stage, the apparent diffusion coefficient (D_app) and the product (2Mk) of the molecules mobility coefficient (M) and the energy gradient coefficient (k) arising from contributions of composition gradient to the energy for PMMI/PVDF (50/50 wt) blend were calculated on the basis of linearized Cahn‐Hilliard‐Cook theory. The kinetic results showed that LLPS of PMMI/PVDF blends followed the spinodal decomposition (SD) mechanism. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1923–1931, 2008     

Oriented crystallization of poly(L‐lactic acid) in uniaxially oriented blends with poly(vinylidene fluoride)

This article describes the oriented crystallization of poly(L ‐lactic acid) (PLLA) in uniaxially oriented blends with poly(vinylidene fluoride) (PVDF). Uniaxially drawn films of PLLA/PVDF blend with fixed ends were heat‐treated in two ways to crystallize PLLA in oriented blend films. The crystal orientation of PLLA depended upon the heat‐treatment process. The crystal c‐axis of the α form crystal of PLLA was highly oriented in the drawing direction in a sample cold‐crystallized at T_c = 120 °C, whereas the tilt‐orientation of the [200]/ [110] axes of PLLA was induced in the sample crystallized at T_c = 120 °C after preheating at T_p = 164.5–168.5 °C. Detailed analysis of the wide‐angle X‐ray diffraction (WAXD) indicated that the [020]/ [310] crystal axes were oriented parallel to the drawing direction, which causes the tilt‐orientation of the [200]/ [110] axes and other crystal axes. Scanning electron microscopy (SEM) suggested that oriented crystallization occurs in the stretched domains of PLLA with diameters of 0.5–2.0 μm in the uniaxially drawn films of PVDF/PLLA = 90/10 blend. Although the mechanism for the oriented crystallization of PLLA was not clear, a possibility was heteroepitaxy of the [200]/[110] axes of the α form crystal of PLLA along the [201]/[111] axes of the β form crystal of PVDF that is induced by lattice matching of d₁₀₀(PLLA) ≈ 5d₂₀₁(PVDF). © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1376–1389, 2008     

Crystallization-induced composition inhomogeneities in PVDF/PMMA blends

Composition profiles develop around growing PVDF spherulites in a blend with PMMA. These profiles assume stationary courses after a certain crystallization time provided that the overall degree of crystallinity is not too high. The composition-dependent growth rate and the diffusion-controlled remove of the surplus PMMA from the spherulite surface are then in a stationary equilibrium. The internal structure of the spherulites will then be homogeneous, too. Upon isothermal crystallization of a PVDF/PMMA = 60/40 (wt %) blend at 160°C for at least 4 h, the spherulites internal degree of crystallinity x_c as related to the PVDF fraction obeys the inequality 55 wt % ≤ x_c ≤ 84 wt %. The overall PMMA content within the spherulites as averaged over its whole inside has been determined by IR microscopy. It amounts to about 15 wt %. In contrast, the PMMA content of the amorphous phase within the spherulites (averaged again over its whole inside) ranges between 28 and 52 wt %. This composition jumps at the spherulite surface to 52 wt %. From the slope of the composition profiles outside the spherulites that have a width of more than 50 μm, the effective chain diffusion coefficient in blends as averaged over both components can be calculated to amount to (250 ± 100) μm²h⁻¹. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2923–2930, 1998     

Crystallization,morphology, and thermal behavior of poly(p‐phenylene sulfide)

This article deals with the structure, crystallization, morphology, and thermal behavior of poly(p‐phenylene sulfide) (PPS) with low‐molecular mass, probed by DSC, optical, and electron microscopy. The growth rates of spherulites were measured over the temperature range 235–275°C. A regime II–III transition was found at T = 250°C. The regime transition was accompanied by a morphological change from sheaflike structure to classical spherulites. The Avrami equation poorly described the isothermal crystallization of PPS, for the occurrence of mixed growth mechanisms and secondary crystallization, in agreement with the morphology and the thermal behavior. Two melting peaks were detected on DSC curves and attributed to the melting of crystals formed isothermally at T_c by primary and secondary crystallization. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 415–424, 2001     

Ringed spherulites in ternary polymer blends of poly(<Emphasis Type="Italic">ε</Emphasis>-caprolactone), poly(styrene-<Emphasis Type="Italic">co</Emphasis>-acrylonitrile), and polymethacrylate

The relationship between ringed spherulite morphology, crystallization regimes/kinetics, and molecular interactions in miscible ternary blends of poly(-caprolactone) (PCL), poly(benzyl methacrylate) (PBzMA), and poly(styrene-co-acrylonitrile) (SAN) was investigated by using differential scanning calorimetry (DSC), polarized optical microscopy (POM), and wide-angle X-ray diffraction (WAXD). The interactions resulted in the deviation of both experimental and calculated T_gs and formation of the specific morphology of the spherulitic structure. Ring-banded spherulites were observed in the PCL/PBzMA/SAN ternary blends. The width of ring bands changed with the blend ratio and the crystallization temperature. Additionally, both composition and wt% of AN in the SAN copolymer had an apparent effect on the morphology of PCL spherulites. Both the crystallization structure of lamellae and molecular interactions greatly influenced the ring bands of PCL spherulites. Furthermore, by using the Flory–Huggins approximation, the depression of the melting point showed that interactions in the PCL/PBzMA/SAN-17 blend were greater than in the PCL/PBzMA/SAN-25 blend. In the ternary blends, the great molecular interactions between amorphous and crystalline polymer resulted in better homogeneity and a larger band period of the extinction rings in the PCL spherulites.     

Thermal behaviors and characteristics of polylactide/poly(butylene succinate) blend films via reactive compatibilization and plasticization

Polylactide (PLA)/poly(butylene succinate) (PBS) blend films modified with a compatibilizer and a plasticizer were hot‐melted through a twin screw extruder and prepared by hydraulic press. Toluene diisocyanate (TDI) and polylactide‐grafted‐maleic anhydride (PLA‐g‐MA) were used as compatibilizers, while triethyl citrate and tricresyl phosphate acted as plasticizers. The effects of the type and content of compatibilizer and plasticizer on the mechanical characteristics, thermal properties, crystallization behavior, and phase morphology of the PLA/PBS blend films were investigated. Reactive compatibilization at increasing levels of TDI improved the compatibility of the PLA and PBS, affecting the toughness of the films. As evidenced by scanning electron microscope, the addition of TDI enhanced the interfacial adhesion of the blends, leading to the appearance of many elongated fibrils at the fracture surface. Furthermore, PLA/PBS blending with both TDI and PLA‐g‐MA led to an acceleration of the cold crystallization rate and an increment of the degree of crystallinity ( ). Toluene diisocyanate could be a more effective compatibilizer than PLA‐g‐MA for PLA/PBS blend films. The synergistic combination of compatibilizer and plasticizer brought a significant improvement in elongation at break and tensile‐impact toughness of the PLA/PBS blends, compared with neat PLA. Their failure mode changed from brittle to ductile due to the improved compatibility and molecular segment mobility of the PLA and PBS phases. Differential scanning calorimeter results revealed that the plasticizers triethyl citrate and tricresyl phosphate changed the thermal behavior of T_cc and T_m, affecting α′ and α crystal formations. However, these plasticizers only slightly improved the thermal stability of the films.     

Porous Biodegradable Polyesters, 3. Preparation of Porous Poly(ε‐caprolactone) Films from Blends by Selective Enzymatic Removal of Poly(L‐lactide)

Porous poly(ε‐caprolactone) (PCL) films were prepared by the removal of poly(L ‐lactide) (PLLA) from phase‐separated PLLA/PCL blend films using the selective Proteinase K™‐catalyzed hydrolysis of PLLA and subsequent elution of its water‐soluble oligomers and monomer into the surrounding hydrolysis media. Polarimetry, gravimetry, and differential scanning calorimetry (DSC) confirmed the complete removal of PLLA molecules from the blend films within 5 d of the Proteinase K‐catalyzed hydrolysis and therefore the formation of porous PCL films when the initial PLLA content [X_PLLA(0)(w/w) = PLLA/(PCL + PLLA)] of the blend films was in the range 0.3–0.5. The fragmentation of the blend film with X_PLLA(0) = 0.7 occurred when the Proteinase K‐catalyzed hydrolysis was continued for longer than 5 d. These findings exhibited that both the PLLA‐rich and PCL‐rich phases were continuous in the blend films for X_PLLA(0) ranges of 0.3–0.7 and of 0.3–0.5, respectively, and that the PCL‐rich phase became dispersed when X_PLLA(0) was increased to 0.7. The dependence of enzymatic hydrolysis rate on X_PLLA(0) strongly suggests that the Proteinase K‐catalyzed hydrolysis of the blend films occurs at the interfaces of PLLA‐rich and PCL‐rich phases as well as at the film surfaces.     

Effect of small amount of poly(ethylene naphthalate) on isothermal crystallization and spherulitic morphology of poly(trimethylene terephthalate)

The effect of a small amount of poly(ethylene naphthalate) (PEN) in its blends with poly(trimethylene terephthalate) (PTT) on isothermal melt-crystallization kinetics and spherulitic morphology of the blends was thoroughly investigated. The maximum PEN content in the blends was 9 wt%. Due to the single composition-dependent glass transition temperature (T_g) that was observed for each blend, these blends appeared to be miscible in the amorphous state. After isothermal crystallization from the melt state, the neat PTT and its blends with PEN exhibited either double or triple melting endotherms. The triple endothermic peaks were observed in both the neat PTT and the blends when being crystallized at crystallization temperatures (T_c) of less than or equal to 195 °C. The equilibrium melting temperature () for the neat PTT was determined based on the linear Hoffman–Weeks extrapolative method to be 248 °C. Such values for the blends were found to decrease with the addition and increasing amount of PEN. Both the neat PTT and the blends were isothermally crystallized over the T_c range of 190–205 °C. At a given T_c, the 97PTT/3PEN blend exhibited a half-time of crystallization (t_0.5) value that was lower, while it exhibited reciprocal half-time (), Avrami rate constant (K_A), and spherulitic growth rate (G) values that were greater, than those of the neat PTT. With further increase in the PEN content, the t_0.5 value increased, while the , K_A, and G values decreased. Analysis of the G values based on the Lauritzen–Hoffman's (LH) secondary nucleation theory showed that the neat PTT and the 91PTT/9PEN blend exhibited a regime II→III transition at 194 °C (467.2 K), while no regime transition was observed for the other two blends. The lateral and the fold surface free energies (σ and σ_e) and the work of chain folding (q) for the neat PTT and the blends were 19.4, 30.2–46.3 erg cm⁻², and 2.4–3.6 kcal mol⁻¹, respectively. Lastly, the effect of both the T_c and the PEN content on morphology and texture of the PTT spherulites was also investigated and the results showed that the texture of the spherulites became coarser with increasing T_c and PEN content.