Fabrication and Characterization of Novel Salicylic Acid Sensors Using Different Reagents (Ferric and Copper)

Abstract

Fabrication of optical fiber salicylic acid (SA) sensors based on immobilization of ferric(III) nitrate and copper(II) acetate on Dowex‐50x8 is presented in this paper. The SA forms a stable purple complex with immobilized Fe³⁺ at pH 2.1 with a response time of 10 min while it forms a stable yellowish green complex with immobilized Cu²⁺ at pH 6.5 with a response time of 8 min. The reflectance spectra of the sensors were measured by using an optical fiber spectrophotometer. The results showed these SA sensors have maximum reflectance at 786 nm and 725 nm for SAFe complex and SACu complex, respectively. The useful dynamic response ranges are 0.02–0.50 g/L (SAFe) and 0.40–1.40 g/L (SACu). These complexes are stable for more than 24 hours. A good reproducibility (0.90%— SAFe; 0.86%— SACu) of measurement was obtained with these sensors.     

Functionalized diacetylenes for nonlinear optical applications: Synthesis,characterization, and the properties of their monolayers

Synthesis and characterization of DA(8/1)OMe (14-{4′-[(methoxy)methoxy] biphenyl}-10,12-tetradecadiynoic acid) and DA(8/1)NBP (14-{4′-[(nitro)methoxy] biphenyl}-10,12-tetradecadiynoic acid ) are presented. Monolayers of DA(8/1)OMe at gas-water interface were investigated. It does not form a stable monolayer nor does it undergo polymerization at the gas-water interface. However, the Ba²⁺ and Cd²⁺ salts formed stable monolayer that polymerized. Polymerization was confirmed by Raman spectroscopy. The diacetylene analog with the more polar tail group, DA(8/1)NBP, does not form a monolayer and undergo polymerization regardless of the subphase condition. A mixed monolayer of DA(8/1)OMe and DA(8/1)NBP forms a true monolayer if the composition of DA(8/1)NBP is 50% or less. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1771–1779, 1999     

Polymorphic crystalline forms of 8OCB

For most alkoxycyanobiphenyls (3OCB, 5OCB, 6OCB, 7OCB and 9OCB) it has been observed that slow or delayed cooling gave rise to a lower melting crystalline polymorphic form which then slowly converted into the higher melting stable crystalline structure. Although under slow evaporation from a solvent, polymorphic crystalline structures were observed also for 8OCB, a polymorphism on cooling like that in other nOCBs has not previously been reported. We have now observed that 8OCB also shows polymorphism, which brings it into line with the other homologues. On keeping the material between 35 and 38 °C after it was cooled from above the melting point of the stable crystal form (55 °C), regular platelets grow usually from one point and fill the whole sample. The texture is stable for weeks at room temperature. Upon heating it shows a melting point at 50 °C, i.e. 5 degrees below the stable crystalline melting point. It is interesting that all platelets are non-symmetric and have the same handedness.     

Polymorphic crystalline forms of 8OCB

For most alkoxycyanobiphenyls (3OCB, 5OCB, 6OCB, 7OCB and 9OCB) it has been observed that slow or delayed cooling gave rise to a lower melting crystalline polymorphic form which then slowly converted into the higher melting stable crystalline structure. Although under slow evaporation from a solvent, polymorphic crystalline structures were observed also for 8OCB, a polymorphism on cooling like that in other nOCBs has not previously been reported. We have now observed that 8OCB also shows polymorphism, which brings it into line with the other homologues. On keeping the material between 35 and 38 °C after it was cooled from above the melting point of the stable crystal form (55 °C), regular platelets grow usually from one point and fill the whole sample. The texture is stable for weeks at room temperature. Upon heating it shows a melting point at 50 °C, i.e. 5 degrees below the stable crystalline melting point. It is interesting that all platelets are non-symmetric and have the same handedness.     

A Surfactant-stable Bacillus pumilus K9 α-Keratinase and Its Potential Application in Detergent Industry

An α-keratinase producing strain was isolated with wool as the sole carbon and nitrogen source and identified as Bacillus pumilus K9. The major amino acids liberated from the keratin degradation of wool by B. pumilus K9 were glutamic acid and leucine. The α-keratinase was purified to electrophoretic homogeneity with a molecular weight of 32000. The purified enzyme exhibits an optimum activity at 60 ℃ and pH=9.0. It was stable at pH values between 8 and 11. Bacillas pumilus keratinase displays a high activity towards casein, keratin, wool and feather, which indicates its wide application range. The keratinase was completely inhibited by phenylmethyl-sulfonyl fluoride(PMSF) and β-mercaptoethanol, and moderately inhibited by ethylemediamine-tetraacetic acid(EDTA), sugges-ting it is a metallo-cysteine keratinase. This enzyme could remain stable that could even be promoted in the presence of surfactants, including sodium dodecyl sulfate(SDS), Tween and Triton. And Tween 40 and Triton X-100 could substantially enhance the activity of the enzyme by 54% and 35%, respectively. It may indicate the prominent feature of the keratinase to tolerate surfactants. The enzymatic properties distinguish this keratinase from others in the literature. Furthermore, this enzyme is extremely stable in the presence of a commercially available detergent with 1% concentration. Detergents ARIEL, Bluemoon and WhiteCat can enhance the activity of the keratinase by 43.56%, 15.22%, and 22.48%, respectively.     

Effect of Strain on the Electronic Structure and Phonon Stability of SrBaSn Half Heusler Alloy

This paper presents the strain effects on the structural, electronic and phonon properties of a newly proposed SrBaSn half Heusler compound. Since it is stable considering chemical thermodynamics, we tested its strength against uniform strain w.r.t phonon spectrum and it produces a direct bandgap of 0.7 eV. The direct bandgap reduces to 0.19 eV at −12% strain beyond which the structure is unstable. However, an indirect gap of 0.63 eV to 0.39 eV is observed in the range of +5% to +8% strain and afterwards the strain application destabilizes the structure. From elastic parameters, the ductile nature of this material is observed.     

Analysis of urinary aromatic acids by liquid chromatography tandem mass spectrometry

The separation and detection of 11 urinary aromatic acids was developed using HPLC-MS/MS. The method features a simple sample preparation involving a single-step dilution with internal standard and a rapid 8 min chromatographic separation. The accuracy was evaluated by the recovery of known spikes between 87 and 110%. Inter- and intra-assay precision (CV) was below 11% in all cases and the analytes were observed to be stable for up to 8 weeks when stored at -20 degrees C. The method was validated based upon linearity, accuracy, precision and stability and was used to establish reference intervals for children and adults.     

A ZIF-8 Host for Dendrite-Free Zinc Anodes and N,O Dual-doped Carbon Cathodes for High-Performance Zinc-Ion Hybrid Capacitors

Zn is a promising anode for aqueous energy storage owing to it intrinsic superior properties such as large capacity, abundant reserves, low potential and safety. But, the growth of dendrites during charge and discharge leads to a decrease in reversibility. In addition, further development of zinc-ion hybrid capacitors (ZICs) is seriously challenging because of the lack of an exceptional cathode. Herein, we use ZIF-8 annealed at 500 °C (annealed ZIF-8) as a host material for stable and dendrite-free Zn anodes. Utilization of annealed ZIF-8 results in dendrite-free Zn deposition and stripping as a result of its porous construction, which contains trace Zn. Furthermore, we firstly proposed innovative N,O dual-doped carbon which was designed by the derived ZIF-8 (ZIF-8 derived C) as cathode for high-energy and power-density ZICs. The new ZIC assembled by Zn@annealed ZIF-8 anode and ZIF-8 derived C cathode provides a capacity of 135.5 mAh g⁻¹ and an energy density of 108.4 Wh kg⁻¹ with a power density of 800 W kg⁻¹ at 1.0 A g⁻¹. In addition, it shows outstanding cycling stability of 91% capacity retention after 6000 cycles at 5.0 A g⁻¹. Moreover, the solid-state ZICs can drive LEDs and smart watches. This ZIC holds promise for the practical application of supercapacitors.     

Substitutional complexometric determination of magnesium in homogeneous water-dioxan medium, based on decomposition of MgEDTA with 8-quinolinol and titration of released EDTA with calcium

A method based on a substitution reaction between MgEDTA and 8-quinolinol, and titration of the liberated EDTA with calcium is proposed. The reaction is performed in homogeneous 50%–60% dioxan medium at ph 10, in which magnesium forms a soluble and stable 8-quinolinol complex.     

Enantiomerically pure alpha-amino aldehydes from silylated alpha-amino acids

The disilylation of alpha-amino acids 1 to provide 2 (72-87%) was achieved without racemization. An unprecedented borane-mediated semi-reduction strategy was devised to convert 2 to stable, isolable oxazaborolidines 3 (100%) which were hydrolyzed to provide 5 (49-60%) as pure, stable compounds. Analysis of the Mosher amides (8) of the gamma-amino esters 7 reveals that < or =2% racemization occurs in the 1 --> 8 conversions.     

离心-电导联用法快速评价O/W乳状液稳定性

建立了乳状液在重力场和离心力场中的沉降/分层速率模型,利用离心加速乳状液的沉降/分层,根据分层后富水相的电导随离心时间的变化关系得到乳状液在离心场中的稳定时间tc,进而推算出乳状液在重力场中的稳定时间tg。这种离心-电导联用方法可快速评价O/W乳状液的稳定性。例如,以质量分数为4%Pluronic F68、1.2%卵磷脂、8%甘露醇和10%IPM配置的乳状液,在8000r/min离心下测得tc为22min,计算出tg为69d;定性分析得到离心分层常数KA=48.0%,结果表明,该配方可得到稳定的O/W乳状液。     

A thermodynamic analysis of stable and metastable equilibria in Fe-Mn-C alloys

Thermodynamic calculations and an analysis of phase transitions and reactions in the Fe-Mn-C system were performed taking into account all the possible stable and metastable states. Special attention was given to the concentration-temperature range of the existence of cementite-type carbides responsible for metal dusting. It was found that, at the temperature most characteristic of this transformation (873 K), cementite with the complex composition (Fe_{1 − y} Mn _y )₃C was a stable phase. An increase in temperature to 973 K slightly narrowed and deformed the region of (Fe_{1 − y} Mn _y )₃C stability. According to the results obtained, it was likely possible to create iron based metallic materials at manganese concentrations increased to 8–12 wt % stable toward destruction in active hydrogen- and carbon-containing gas media. This conclusion was substantiated experimentally.     

Stable competitive enzyme-linked immunosorbent assay kit for rapid measurement of 11 active beta-lactams in milk, tissue, urine, and serum

Beta-lactams are used as veterinary drugs for the treatment of food-producing animals. For consumer protection, legislation is in place to set limits for their residues. An enzyme-linked immunosorbent assay (ELISA) was developed which allowed, in a single reaction, the class-specific measurement of 11 beta-lactams, with limits of detection below European maximum residue limits. Determinations were feasible in milk, tissue, urine, and serum with simple and rapid sample preparation. In this format, the specific capture antibodies were precoated on the microtiter plate and horseradish peroxidase-labeled conjugate was used to compete with free beta-lactams. The stability of the precoated microtiter plate and conjugate was at least 1 year when stored at 2 to 8 degrees C; upon reconstitution, the conjugate was stable for 6 days at 2 to 8 degrees C. The stability of lyophilized ampicillin standards was at least 6 months when stored at 2 to 8 degrees C and at least 1 year when stored at -20 degrees C. A low cross-reactivity, 3.6%, was observed with ampicillin with open beta-lactam ring relative to 100% for intact ampicillin. Generic recognition was shown by relative cross-reactivity values ranging from 22 (penicillin V) to 144% (nafcillin). Cross-reactivity for cephalosporins was <0.1%. Intra- and interassay precisions expressed as coefficient of variation were typically 2-8%. The inhibitory concentration with 50% binding for ampicillin was typically 2 ppb. Recovery for different spiked levels was >70% with all the matrixes.     

Development of 5-[(3-aminopropyl)phosphinooxy]-2-(hydroxymethyl)-4H-pyran-4-one as a novel whitening agent

A stable derivative of kojic acid, 5-[(3-aminopropyl)phosphinooxy]-2-(hydroxymethyl)-4H-pyran-4-one (Kojyl-APPA), was synthesized in good yield. The effects of Kojyl-APPA on tyrosinase activity and melanin synthesis were investigated. Kojyl-APPA showed tyrosinase inhibition effect (30%) in situ, but not in vitro. Kojyl-APPA inhibited tyrosinase activity significantly at 24 h after treatment in normal human melanocytes. It means that Kojyl-APPA is not a direct inhibitor of tyrosinase itself, but it is converted to a potential inhibitor kojic acid enzymatically in cells. In addition, Kojyl-APPA decreased melanin content to 75% of control in melanoma cells and decreased neomelanin synthesis to 43% of control in normal human melanocytes. Its permeation through skin increased by about 8 times as compared with kojic acid.     

Mechanism of Oxygen Adsorption on Partially K Exchanged Na-A Type Zeolite

Accordingly, the observation of oxygen selectivity on Na-K-A would indicate that nitrogen has a greater steric hindrance at the window than does oxygen. Using single crystal X-ray diffraction (SCXD), it was confirmed that K at 8-member rings was relocated to 6-member rings and that the location of Na at 8-member rings became uncertain with calcination. It was also observed that Na-K-A was thermally more stable than Na-A. Using magic angle spin nuclear magnetic resonance (MAS-NMR), it was confirmed that Na at 8-member rings irreversibly changed location from a symmetric position to an asymmetric position with calcination.Using the atomic positions determined by SCXD, the mean square displacements (MSD) of oxygen and nitrogen inside the crystal of Na-A and Na-K-A were estimated by means of molecular dynamic simulation (MD). When temperature was decreased, the MSD of nitrogen was reduced to a greater extent than that of oxygen and the MSD of nitrogen inside Na-K-A was reduced by a greater margin than that inside Na-A.     

Synthesis and biodistribution of the 99m TcN-DMSA complex as a potential bone imaging agent

In this study, the preparation of the 99m TcN complex of DMSA (dimercaptosuccinicacid) was carried out as a freeze-dried formulation, through a simple procedureinvolving the initial of 99m TcO 4 – with succinic dihydrazide in thepresence of stannous chloride as reducing agent, followed by the additionof the ligand DMSA to afford the final product. The radiochemical purity ofthe 99m TcN-DMSA complex was over 90% determined by thin layer chromatography.It was stable over 8 hours at room temperature. Its partition coefficientindicated that it was a good hydrophilic complex. Biodistribution in miceshowed that the 99m TcN-DMSA complex was accumulated in bone with high uptakeand good retention, suggesting it would be potentially useful as a bone imagingagent containing the [ 99m TcN] 2+ core. The biodistribution comparison inmice of the 99m TcN-DMSA complex and the 99m Tc-DMSA complex indicate thatthe presence of the 99m Tc nitrido group significantly alters the biologicalproperties of the 99m Tc complex.     

Continuous Flow Determination of Residual Aqueous Ozone With Membrane Separation-Chemiluminescent Detection

Abstract

A method for the determination of ultra-trace aqueous ozone utilizing a membrane-separation process and a chemiluminescent detector is proposed. The microporous PTFE tube was used as separator to transfer aqueous ozone into a gas phase. Air bubbling was used to enhance the separation. Chemilumi nescent signals produced from the reaction of ozone with ethylene in air were linearly proportional to concentration of aqueous ozone from 8 ppb to 9.5 ppm. The relative standard deviation (n=4) was 3.5% at 0.2 ppm. The time it took from starting the sample flow until the signal to reach a stable level was 1.5 min. The interference from chromium(VI), manganese(VII), chlorine, bromine, phthalate, and sulfophthalate was completely eliminated.     

Template-directed synthesis of kinetically and thermodynamically stable molecular necklace using ring closing metathesis

We report the template-directed synthesis of a well-defined, kinetically stable [5]molecular necklace with dialkylammonium ion (R(2)NH(2)(+)) as recognition site and DB24C8 as macrocycle. A thread containing four dialkylammonium ions with olefin at both ends was first synthesized and then subjected to threading with an excess amount of DB24C8 to form pseudo[5]rotaxane, which in situ undergoes ring closing metathesis at the termini with second generation Grubbs catalyst to yield the desired [5]molecular necklace. The successful synthesis of [5]molecular necklace is mainly attributed to the self-assembly and dynamic covalent chemistry which allows the formation of thermodynamically most stable product. The self-assembly of the DB24C8 ring onto the recognition site known as templating effect was driven by noncovalent stabilizing interactions like [N(+)-H···O], [C-H···O] hydrogen bonds as well as [π···π] interactions which is facilitated in non-polar solvents. The reversible nature of olefin metathesis reaction makes it suitable for dynamic covalent chemistry since proof-reading and error-checking operates until it generates thermodynamically the most stable interlocked molecule. Riding on the success of [5]molecular necklace, we went a step further and attempted to synthesize [7]molecular necklace using the same protocol. This led to the synthesis of another thread with olefin at both ends but having six dibenzylammonium ions along the thread. However, the extremely poor solubility of this thread containing six secondary ammonium ions limits the self-assembly process even after we replaced the typical PF(6)(-) counter anion with a more lipophilic BPh(4)(-) anion. Although the poor solubility of the thread remains the bottleneck for making higher order molecular necklaces yet this approach of "threading-followed-by-ring-closing-metathesis" for the first time produces kinetically and thermodynamically stable, well-defined, homogeneous molecular necklace which was well characterized by one-dimensional, two-dimensional, variable temperature proton NMR spectroscopy and ESI mass spectroscopy.     

离子色谱法测定石墨及其制品中的F~-和SO_4~(2-)

建立了离子色谱法测定石墨及其制品中F~-和SO_4~(2-)的检验方法。用乙酸钠灼烧样品,水微沸提取,过滤定容,过滤膜后用离子色谱对溶液中的F~-和SO_4~(2-)含量进行测定。选用3.6 mmol/L Na_2CO_3溶液为淋洗液,流量为0.7 mL/min,渗析时间为8 min,转移时间为30 s。F~-和SO_4~(2-)平均加标回收率分别为92.4%,105.2%;测定结果的相对标准偏差分别为1.42%,3.89%(n=8)。该方法稳定,操作简便,准确度高,分析速度快,适用于石墨及其制品中F~-及SO_4~(2-)的测定。     

Stable pi-dimer of a tetrathiafulvalene cation radical encapsulated in the cavity of cucurbit[8]uril

The first stable pi-dimer of a tetrathiafulvalene (TTF) cation radical encapsulated in the cavity of cucurbit[8]uril has been isolated at room temperature and fully characterized; it shows absorption bands at 400, 540 and 760 nm, characteristic of the TTF cation radical dimer.