Application of modified multiwalled carbon nanotubes as solid sorbent for separation and preconcentration of trace amounts of manganese ions

In this work, the potential of modified multiwalled carbon nanotubes for separation and preconcentration of trace amounts of manganese ion is studied. Multiwalled carbon nanotubes were oxidized with concentrated HNO₃ and then modified with loading 1-(2-pyridylazo)-2-naphtol. Mn(II) ions could be quantitatively retained by modified multiwalled carbon nanotubes in the pH range of 8–9.5. Elution of the adsorbed manganese was carried out with 5.0 mL of 0.1 mol L^?1 HNO₃. Detection limit is 0.058 ng mL^?1 and analytical curve is linear in the range of 0.1 ng mL^?1–5.0 μg mL^?1 in the initial solution with a correlation coefficient 0.9977 and the preconcentration factor is 100. Relative standard deviation for eight replicate determination of 0.5 μg mL^?1 of manganese in the final solution is 0.41%. The effects of the experimental parameters, including the sample pH, flow rates of sample and eluent solution, eluent type, breakthrough volume and interference ions, were studied for preconcentration of Mn(II) ions in detail to optimize the conditions. The method was successfully applied for separation, preconcentration and determination of manganese in different samples.     

Preconcentration procedure trace amounts of palladium using modified multiwalled carbon nanotubes sorbent prior to flame atomic absorption spectrometry: 1st Nano Update

A method for preconcentration of palladium at trace level on modified multiwalled carbon nanotubes columns and determination by flame atomic absorption spectrometry (FAAS) has been developed. Multiwalled carbon nanotubes (MWCNTs) were oxidized with concentrated HNO₃ and the oxidized multiwalled carbon nanotubes were modified with 5-(4′-dimethylamino benzyliden)-rhodanine, and then were used as a solid sorbent for preconcentration of Pd(II) ions. Factors influencing sorption and desorption of Pd(II) ions were investigated. The sorption of Pd(II) ions was quantitative in the pH range of 1.0–4.5, whereas quantitative desorption occurs with 3.0 mL 0.4 mol L^?1 thiourea. The amount of eluted palladium was measured using flame atomic absorption spectrometry. The effects of experimental parameters, including sample flow rate, eluent flow rate, and eluent concentration were investigated. The effect of coexisting ions showed no interference from most ions tested. The proposed method permitted a large enrichment factor (about 200). The relative standard deviation of the method was ±2.73% (for eight replicate determination of 2.0 μg mL^?1 of Pd(II)) and the limit of detection was 0.3 ng mL^?1. The method was applied to the determination of Pd(II) in water, road dust, and standard samples.     

A novel sensitive non-enzymatic glucose sensor

Cu nanoclusters were electrochemically deposited on the film of a Nafion-solubilized multi-wall carbon nanotubes (CNTs) modified glassy carbon electrode (CNTs-GCE), which fabricated a Cu-CNTs composite sensor (Cu-CNTs-GCE) to detect glucose with non-enzyme. The linear range is 7.0×10-7 to 3.5×10-3 mol/L with a high sensitivity of 17.76μA/(mmol L), with a low detection limit 2.1×10-7 mol/L, fast response time (within 5 s), good reproducibility and stability.     

Pyrohydrolysis of carbon nanotubes for Br and I determination by ICP-MS

Bromine and iodine determination was performed in carbon nanotubes (CNTs) by inductively coupled plasma mass spectrometry (ICP-MS) after sample preparation using pyrohydrolysis. Samples of CNTs (up to 500 mg) were mixed with 750 mg of V₂O₅ and heated at 950 °C during 12.5 min in a quartz tube under water vapor and air. The main operational conditions of pyrohydrolysis (carrier gas, absorbing solution, heating time, sample mass and use of V₂O₅) were evaluated. Accuracy was evaluated using certified reference materials (CRM) with similar matrix and also by comparison of results obtained after digestion of samples by microwave-induced combustion (MIC) and determination by ICP-MS. Agreement with CRM values was higher than 97% for Br and better than 96% in comparison with reference values (MIC/ICP-MS) of Br and I in CNTs samples. The limit of detection of the method for Br and I determination by ICP-MS was 0.05 and 0.004 μg g^? 1, respectively. Using a relatively simple and low cost pyrohydrolysis apparatus up to four samples can be processed per hour. The pyrohydrolysis sample preparation procedure is easy to be performed and provide a clean solution for analysis by ICP-MS, which is very attractive for Br and I control in CNTs.     

Microwave-radiated synthesis of gold nanoparticles/carbon nanotubes composites and its application to voltammetric detection of trace mercury(II)

Gold nanoparticles/carbon nanotubes (Au-NPs/CNTs) composites were rapidly synthesized by microwave radiation, and firstly applied for the determination of trace mercury(II) by anodic stripping voltammetry (ASV). The structure and composition of the synthesized Au-NPs/CNTs nanocomposites were characterized by transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX), UV–vis absorption spectroscopy and cyclic voltammetry. Au-NPs/CNTs nanocomposites modified glassy carbon electrode (Au-NPs/CNTs/GCE) exhibited excellent performance for Hg(II) analysis. A wide linear range (5 × 10⁻¹⁰–1.25 × 10⁻⁶ mol/L) and good repeatability (relative standard deviation of 1.84%) were obtained for Hg(II) detection. The limit of detection was found to be 3 × 10⁻¹⁰ mol/L (0.06 μg/L) at 2 min accumulation, while the World Health Organization’s guideline value of mercury for drinking water is 1 μg/L, suggesting the proposed method may have practical utility.     

Cloud point extraction for determination of cadmium in soft drinks by thermospray flame furnace atomic absorption spectrometry

Cloud point extraction (CPE) is proposed as a preconcentration procedure for the determination of Cd in soft drinks by thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS). The cadmium reacted with pyridyl-azo-naphthol (PAN) to form hydrophobic chelates, which were extracted into the micelles of Triton X-114 in a solution buffered at pH 9. NaCl was used for the phase separation. The variables which affect the preconcentration were optimized using a 2³ factorial design and central composite design (CCD). A response surface maximum point was obtained, and the critical values were a concentration of 0.13 mmol L^? 1 PAN, 0.03% m/v Triton X-114 and 2.3% m/v NaCl. Under the optimized conditions, after the extraction and preconcentration steps, a sample volume of 100 μL was introduced into the hot Ni tube using water as the carrier at a flow rate of 0.4 mL min^? 1. The values obtained for the detection limit, relative standard deviation and preconcentration factor were 0.0178 μg L^? 1, 4.1% (n = 8) and 55.5, respectively. The accuracy of the proposed method was demonstrated by performing addition-recovery experiments. Recoveries varied from 88 to 104%.     

Analytical possibilities of different X-ray fluorescence systems for determination of trace elements in aqueous samples pre-concentrated with carbon nanotubes

This study was aimed to achieve improved instrumental sensitivity and detection limits for multielement determination of V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, Se, Pb and Cd in liquid samples by using different X-ray fluorescence (XRF) configurations (a benchtop energy-dispersive X-ray fluorescence spectrometer, a benchtop polarised energy-dispersive X-ray fluorescence spectrometer and a wavelength-dispersive X-ray fluorescence spectrometer).The preconcentration of metals from liquid solutions consisted on a solid-phase extraction using carbon nanotubes (CNTs) as solid sorbents. After the extraction step, the aqueous sample was filtered and CNTs with the absorbed elements were collected onto a filter paper which was directly analyzed by XRF.The calculated detection limits in all cases were in the low ng mL^− 1 range. Nevertheless, results obtained indicate the benefits, in terms of sensitivity, of using polarized X-ray sources using different secondary targets in comparison to conventional XRF systems, above all if Cd determination is required.The developed methodologies, using the aforementioned equipments, have been applied for multielement determination in water samples from an industrial area of Poland.     

On-line solid phase extraction of Ni and Pb using carbon nanotubes and modified carbon nanotubes coupled to ETAAS

A study about the capabilities of three kinds of nanomaterials namely, carbon nanotubes (CNT), oxidized carbon nanotubes (ox-CNT) and l-alanine immobilized on carbon nanotubes (ala-CNT) to serve as sorbents for preconcentrating Ni and Pb using an on-line system coupled to electrothermal atomic absorption spectroscopy (ETAAS) technique, was accomplished. The solid phase extraction was performed in a conical minicolumn used as sorbent holder. After loading a fixed volume of the analytes, they were eluted with a discrete volume (50 μL) of nitric acid, placed directly into the platform of a L’Vov tube. After that, each analyte was determined individually. Ni and Pb retention was strongly influenced by pH but exhibiting different behaviors. The study demonstrated that the sorbent based on ox-CNTs was the one that exhibited the highest capacity and linearity for both analytes when compared with CNT or ala-CNT. The analytical performance was evaluated for the three sorbents to establish the best conditions regarding sensitivity, reproducibility and accuracy. The precision expressed as relative standard deviations (n = 6) were 3.9 and 0.5% for Ni²⁺ and Pb²⁺, respectively The limit of detection (LOD), calculated as the concentration required to yield a net peak equal to three times the standard deviation of the background signal (3σ) was 30 and 10 ng L⁻¹ for Ni²⁺ and Pb²⁺ respectively. Alternatively, the limit of quantification (10σ) was calculated and resulted to be 0.79 and 0.07 μg L⁻¹ for Ni²⁺ and Pb²⁺ respectively. After optimization, the method that involved the use of ox-CNT associated to an on-line preconcentration was tested in samples of relevant environmental importance. Accuracy was evaluated analyzing a certified reference material namely, Municipal Sludge (QC MUNICIPAL SLUDGE A) and a reference sample of Lake Sediment (TRAP-LRM from IJS).     

Simultaneous removal of copper(II), lead(II), zinc(II) and cadmium(II) from aqueous solutions by multi-walled carbon nanotubes

Multi-walled carbon nanotubes (MWCNTs) were used successfully for the removal of heavy metals from aqueous solution. Characterization techniques showed the carbon as nanotubes with an average diameter between 40 and 60 nm and a specific surface area of 61.5 m² g^?1. The effect of carbon nanotubes mass, contact time, metal ions concentration, solution pH, and ionic strength on the adsorption of Cu(II), Pb(II), Cd(II) and Zn(II) by MWCNTs were studied and optimized. The adsorption of the heavy metals from aqueous solution by MWCNTs was studied kinetically using different kinetic models. A pseudo-second order model and the Elovich model were found to be in good agreement with the experimental data. The mechanism of adsorption was studied by the intra-particle diffusion model, and the results showed that intra-particle diffusion was not the slowest of the rate processes that determined the overall order. This model also revealed that the interaction of the metal ions with the MWCNTs surface might have been the most significant rate process. There was a competition among the metal ions for binding of the active sites present on the MWCNTs surface with affinity in the following order: Cu(II) > Zn(II) > Pb(II) > Cd(II).     

Hybrid magnetic amphiphilic composites based on carbon nanotube/nanofibers and layered silicates fragments as efficient adsorbent for ethynilestradiol

In this work, hybrid magnetic amphiphilic composites were prepared by the catalytic growth of carbon nanotubes (CNTs) and nanofibers CNF on layered silicates fragments. SEM, TEM, Raman, XRD, Mössbauer, TG/DTA showed that CVD with CH₄ at 800 °C produced CNF and magnetic Fe cores fixed on the surface of microfragments of silicates layers. Due to the amphiphilic character, the composites can be easily dispersed in water and efficiently adsorb hydrophobic contaminant molecules. For example, the composites showed remarkable adsorption capacities for the hormone ethinylestradiol, e.g. 2–4 mg m^?2, compared to ca. 0.1 mg m^?2 obtained for high surface area activated carbon and multiwall CNT. These results are discussed in terms of a high hydrophobic exposed surface area of the CNT and CNF fixed on the layered silicates fragments surface. Moreover, the composites can be easily removed from water by a simple magnetic separation process.     

Amperometric glucose sensor based on glucose oxidase immobilized on gelatin-multiwalled carbon nanotube modified glassy carbon electrode

We investigated the direct electrochemistry of glucose oxidase (GOx) at gelatin-multiwalled carbon nanotube (GCNT) modified glassy carbon electrode (GCE). GOx was covalently immobilized onto GCNT modified GCE through the well known glutaraldehyde (GAD) chemistry. The immobilized GOx showed a pair of well-defined reversible redox peaks with a formal potential (E⁰′) of ? 0.40 V and a peak to peak separation (ΔE_p) of 47 mV. The surface coverage concentration (Г) of GOx in GCNT/GOx/GAD composite film modified GCE was 3.88 × 10^? 9 mol cm^? 2 which indicates the high enzyme loading. The electron transfer rate constant (k_s) of GOx immobilized onto GCNT was 1.08 s^? 1 which validates a rapid electron transfer processes. The composite film shows linear response towards 6.30 to 20.09 mM glucose. We observed a good sensitivity of 2.47 μA mM^?1 cm^? 2 for glucose at the composite film. The fabricated biosensor displayed two weeks stability. Moreover, it shows no response to 0.5 mM of ascorbic acid (AA), uric acid (UA), acetaminophen (AP), pyruvate (PA) and lactate (LA) which shows its potential application in the determination of glucose from human serum samples. The composite film exhibits excellent recovery for glucose in human serum at physiological pH with good practical applicability.     

On-line preconcentration/separation of inorganic arsenic and antimony by poly (aryl ether ketone) containing pendant carboxyl groups prior to microwave plasma atomic spectrometry determinations

A flow injection-column adsorption preconcentration-microwave plasma atomic emission spectrophotometric (FI-column-MP-AES) method is developed for on-line determining trace levels of inorganic arsenic and antimony released from packaging glass containers. The developed methodology involves a micro-column packed with poly (aryl ether ketone) containing pendant carboxyl groups (PEK-L) for adsorption preconcentration procedure before the determination by MP-AES. The main parameters affecting the preconcentration/separation are investigated in details. Under the optimized conditions, the detection limit of the proposed technique is 0.27 μg L^? 1 for As and 0.38 μg L^? 1 for Sb. Precisions, evaluated as repeatability of results (relative standard deviation with n = 7), are 2.8 and 1.8% respectively for As and Sb. The proposed method has been applied to different reference materials and glass bottle packaging samples with satisfactory results.     

Silver modified magnetic carbon nanotubes composite as a selective solid phase extractor for preconcentration and determination of trace mercury ions in water solution

A magnetic composite of silver/iron oxides/carbon nanotubes (Ag/Fe₃O₄/CNTs) was synthesized and used as an adsorbent for the preconcentration of mercury ions in water solutions at room temperature (25°C) in this study. The silver nanoparticles were supported on the magnetic CNTs. The modification enabled the composite had not only a high adsorption capacity for mercury ions (Hg²⁺) but also the magnetic isolation properties. A fast, sensitive, and simple method was successfully developed for the preconcentration and determination of trace amount of Hg²⁺ in water using the synthesized nanocomposite as adsorbent. The mercury concentration was determined by an atomic fluorescence spectrometer (AFS). The experimental conditions such as pH value, extraction temperature, extraction time, sample volume, eluent composition and concentration, sorbent amount, and coexisting ions were investigated for the optimization. A 500 mL of sample volume resulted in a preconcentration factor of 125. When a 200 mL of sample was employed, the limit of detection for Hg²⁺ was as low as 0.03 ng mL^?1with relative standard deviation of 4.4% at 0.1 ng mL^?1 (n = 7). The ease of synthesis and separation, the good adsorption capacity, and the satisfactory recovery will possibly make the composite an attractive adsorbent for the preconcentration of ultratrace Hg²⁺ in waters.     

Highly selective solid-phase extraction of trace Pd(II) by murexide functionalized halloysite nanotubes

The originality on the high efficiency of murexide modified halloysite nanotubes as a new adsorbent of solid phase extraction has been reported to preconcentrate and separate Pd(II) in solution samples. The new adsorbent was confirmed by Fourier transformed infrared spectra, X-ray diffraction, scanning electron microscope, transmission electron microscope and N₂ adsorption–desorption isotherms. Effective preconcentration conditions of analyte were examined using column procedures prior to detection by inductively coupled plasma-optical emission spectrometry (ICP-OES). The effects of pH, the amount of adsorbent, the sample flow rate and volume, the elution condition and the interfering ions were optimized in detail. Under the optimized conditions, Pd(II) could be retained on the column at pH 1.0 and quantitatively eluted by 2.5 mL of 0.01 mol L^?1 HCl–3% thiourea solution at a flow rate of 2.0 mL min^?1. The analysis time was 5 min. An enrichment factor of 120 was accomplished. Common interfering ions did not interfere in both separation and determination. The maximum adsorption capacity of the adsorbent at optimum conditions was found to be 42.86 mg g^?1 for Pd(II).The detection limit (3σ) of the method was 0.29 ng mL^?1, and the relative standard deviation (RSD) was 3.1% (n = 11). The method was validated using certified reference material, and has been applied for the determination of trace Pd(II) in actual samples with satisfactory results.     

Fabrication of super-macroporous nanocomposites by deposition of carbon nanotubes onto polymer cryogels

Electrically conducting super-macroporous carbon nanotube/polymer cryogel nanocomposites were fabricated by a novel approach based on deposition of carbon nanotubes (CNTs) onto the inner surface of pre-formed cryogels assisted by cryogenic treatment. Stable aqueous dispersions of multi-walled and single-walled carbon nanotubes were firstly obtained by non-covalent modification of pristine nanotubes with either pyrene containing polydimethylacrylamide or poly(ethylene oxide)₂₆-b-poly(propylene oxide)₄₀-b-poly(ethylene oxide)₂₆ copolymers and, then, exploited for the preparation of nanocomposites. The mechanical and electrical properties of nanocomposite materials were measured and compared to similar materials prepared by established method. The novel approach provided super-macroporous nanocomposites with high electrical conductivity (>10^?2 S/m) at much lower nanotube content (0.12 wt.%).     

Gelatin-functionalized carbon nanotubes for the bioelectrochemistry of hemoglobin

In this paper, we compared the use of gelatin-functionalized carbon nanotubes (CNTs) as substrates for Hemoglobin (Hb) immobilization and as electrodes for electrochemical reduction of the absorbed Hb. The non-covalently gelatin-functionalized CNTs possessed an improved solubility in aqueous solution and may have an enhanced biocompatibility with Hb. The characteristics of Hb/gelatin-CNTs composite films were studied by using UV–vis spectroscopy, FTIR spectroscopy and electrochemical methods. The immobilized Hb showed a couple of quasi-reversible redox peaks with a formal potential of −0.35 V (vs. SCE) in 0.10 M pH 7.0 phosphate buffer solution (PBS). The surface concentration of electroactive Hb immobilized on gelatin-CNT/GC electrode was about 4.34 × 10⁻¹⁰ mol cm⁻².     

Determination of trace heavy metals in herbs by sequential injection analysis-anodic stripping voltammetry using screen-printed carbon nanotubes electrodes

A method for the simultaneous determination of Pb(II), Cd(II), and Zn(II) at low μg L⁻¹ concentration levels by sequential injection analysis-anodic stripping voltammetry (SIA-ASV) using screen-printed carbon nanotubes electrodes (SPCNTE) was developed. A bismuth film was prepared by in situ plating of bismuth on the screen-printed carbon nanotubes electrode. Operational parameters such as ratio of carbon nanotubes to carbon ink, bismuth concentration, deposition time and flow rate during preconcentration step were optimized. Under the optimal conditions, the linear ranges were found to be 2-100 μg L⁻¹ for Pb(II) and Cd(II), and 12-100 μg L⁻¹ for Zn(II). The limits of detection (S_bl/S = 3) were 0.2 μg L⁻¹ for Pb(II), 0.8 μg L⁻¹ for Cd(II) and 11 μg L⁻¹ for Zn(II). The measurement frequency was found to be 10-15 stripping cycle h⁻¹. The present method offers high sensitivity and high throughput for on-line monitoring of trace heavy metals. The practical utility of our method was also demonstrated with the determination of Pb(II), Cd(II), and Zn(II) by spiking procedure in herb samples. Our methodology produced results that were correlated with ICP-AES data. Therefore, we propose a method that can be used for the automatic and sensitive evaluation of heavy metals contaminated in herb items.     

Functionalization of multi-walled carbon nanotubes with poly(amidoamine) dendrimer for mediator-free glucose biosensor

By grafting with poly(amidoamine) (PAMAM) dendrimer, novel carbon nanotube (CNT) nano-composites have been successfully prepared. The novel functionalized matrix with plenty amino groups circumvents the troublesome solubility problem of CNTs in solvents, especially in water, greatly expanding the scope of the application of carbon nanotubes. The GO_x and HRP immobilized CNT-PAMAM based on the functional CNTs was synthesized. The bi-enzymatic CNT-PAMAM nano-composites are highly dispersible in water and show very promising applications in the fabrication of mediator-free bi-enzymatic biosensors for sensitive detection of glucose. The cooperation of nano-composite between CNT and high dense GO_x and HRP results in very high sensitivity to glucose with a current response of 2200 nA mM⁻¹ and fast response (∼1 s). The modified electrode exhibits a wide linear response range for glucose from 4.0 μM to 1.2 mM (R = 0.9971, N = 15), with a detection limit of 2.5 μM. The negative electrode potential of −0.34 V is favorable for glucose detection in real samples without interference caused by other biomolecules.     

Electrochemiluminescence immunosensor based on nanocomposite film of CdS quantum dots-carbon nanotubes combined with gold nanoparticles-chitosan

A novel and sensitive electrochemiluminescence (ECL) immunosensor based on CdS quantum dots (QDs)-carbon nanotubes (CNTs) and gold nanoparticles-chitosan (GNPs-CHIT) was presented. CdS QDs ECL was much enhanced by combing poly(diallyldimethylammonium chloride) functionalized CNTs. GNPs-CHIT nanohybrids was used to construct an effective antibody immobilization matrix with excellent stability and bioactivity. The principle of ECL detection for target human IgG is based on the increment of steric hindrance after immunoreaction, which resulted in the decrease in ECL intensity. The linear response range was between 0.006 and 150 ng mL^?1, and the detection limit was 0.001 ng mL^?1. This approach offers obvious advantages of being simpler, faster, and more stable compared with other immunosensors, which possesses great potential for protein detection in clinical laboratory.     

Amperometric ascorbic acid biosensor based on carbon nanoplatelets derived from ground cherry husks

In this work, a novel amperometric biosensor based on carbon nanoplatelets derived from ground cherry (Physalis peruviana) husks (GCHs-CNPTs) is reported for the sensitive and selective detection of ascorbic acid (AA). The structure of the nanoplatelets, the oxygen-containing groups and edge-plane-like defective sites (EPDSs) on the GCHs-CNPTs were characterized by scanning electron microscopy, X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. The presence of GCHs-CNPTs with a high density of EPDSs effectively enhances the electron transfer between AA and the glassy carbon electrode (GCE), and thus induces a substantial decrease in the overvoltage for AA oxidation compared with both a bare GCE and a GCE modified with carbon nanotubes (CNTs/GCE). In particular, an amperometric biosensor based on GCHs-CNPTs exhibited a wider linear range (0.01–3.57 mM), higher sensitivity (208.63 μA mM^− 1 cm^− 2), a lower detection limit (1.09 μM, S/N = 3) and better resistance to fouling for AA determination compared to a CNTs/GCE. The great potential of the GCHs-CNPTs/GCE for practical and reliable AA analysis was demonstrated by the successful determination of AA in samples taken from a medical injection dose and a soft drink.