Defect-mediated formation of Ag cluster-doped TiO2 nanoparticles for efficient photodegradation of pentachlorophenol

A novel strategy was designed to prepare Ag cluster-doped TiO(2) nanoparticles (Ag/TiO(2) NPs) without addition of any chemical reducing agent and/or organic additive. A defect-rich TiO(x) species was generated by laser ablation in liquid (LAL) of a Ti target. The silver ions could be reduced and deposited on the surface of TiO(2) NPs through the removal of oxygen vacancies and defects; the TiO(x) species evolved into anatase NPs in a hydrothermal treatment process. The derived Ag/TiO(2) NPs are approximately 25 nm in size, with narrow size distribution. The Ag clusters are highly dispersed inside TiO(2) and less than 3 nm in size. The doped amount can be tuned by changing the concentration of Ag(+) ions. The as-synthesized Ag/TiO(2) NPs display improved photocatalytic efficiency toward pentachlorophenol (PCP) degradation.     

Ag担载对TiO2光催化活性的影响

 采用光化学沉积法合成了Ag/TiO2光催化剂,以苯酚降解反应考察了光催化剂活性随Ag担载量的变化,用TEM观察了Ag在TiO2表面的分布与形貌,以漫反射紫外-可见光谱(DRS)分析了不同Ag担载量的光催化剂的光谱特征. 结果表明,适宜担载量的Ag可显著提高TiO2的光催化活性. TEM观察显示,Ag在TiO2表面形成纳米级团簇结构,随Ag担载量的增加,团簇尺寸增大. DRS分析表明,Ag的担载对TiO2紫外区域的光谱特征没有影响. 根据Ag团簇的能级随其几何尺寸的变化分析了Ag担载量的变化对TiO2光催化活性的影响机理.     

Probing the electronic structure and band gap evolution of titanium oxide clusters (TiO(2))(n)(-) (n = 1-10) using photoelectron spectroscopy

TiO2 is a wide-band-gap semiconductor, and it is an important material for photocatalysis. Here we report an experimental investigation of the electronic structure of (TiO2)n clusters and how their band gap evolves as a function of size using anion photoelectron spectroscopy (PES). PES spectra of (TiO2)n- clusters for n = 1-10 have been obtained at 193 nm (6.424 eV) and 157 nm (7.866 eV). The high photon energy at 157 nm allows the band gap of the TiO2 clusters to be clearly revealed up to n = 10. The band gap is observed to be strongly size-dependent for n < 7, but it rapidly approaches the bulk limit at n = 7 and remains constant up to n = 10. All PES features are observed to be very broad, suggesting large geometry changes between the anions and the neutral clusters due to the localized nature of the extra electron in the anions. The measured electron affinities and the energy gaps are compared with available theoretical calculations. The extra electron in the (TiO2)n- clusters for n > 1 appears to be localized in a tricoordinated Ti atom, creating a single Ti3+ site and making these clusters ideal molecular models for mechanistic understanding of TiO2 surface defects and photocatalytic properties.     

Kinetic and DFT studies on the Ag/TiO2-photocatalyzed selective reduction of nitrobenzene to aniline.

TiO2 particles loaded with silver nanoparticles with a mean diameter of 1.5 nm exhibit a high photocatalytic activity (84 % conversion after 1 h irradiation) for the reduction of nitrobenzene to aniline with 100 % selectivity in the presence of CH3OH (concentration=100 mM). High-resolution transmission electron microscopic studies of Pt-photodeposited Ag/TiO2 demonstrate that the Ag nanoparticles act as reduction sites in the photocatalytic reaction. Both spectroscopic measurements and density functional theory (DFT) calculations reveal that nitrobenzene is selectively adsorbed onto the Ag surfaces of Ag/TiO2 via partial electron transfer from Ag to nitrobenzene, whereas the interaction between aniline and Ag/TiO2 is weak. The kinetic analysis indicates that the recombination between the electrons flowing into the Ag nanoparticle and the holes left in the TiO2 valence band is significantly suppressed, particularly in the presence of CH3OH. The high activity and selectivity in the present Ag/TiO2-photocatalyzed reduction are rationalized in terms of the charge separation efficiency, the selective adsorption of the reactants on the catalyst surfaces, and the restriction of the product readsorption.     

反相乳液中Ag/TiO2纳米杂化粒子的制备及其SERS效应

在反相乳液的微环境中用一步反应法制备了Ag/TiO2纳米杂化粒子,并用TEM,SPS,XPS及XRD等方法进行了表征.结果表明,Ag粒子(5-15nm)已镶嵌在TiO2(30-50nm)结构中,并且具有SERS活性.     

TiO2浓度对核-壳结构Ag/TiO2纳米复合粒子结构以及三阶非线性光学性质的影响

采用光还原方法制备了核-壳结构的Ag/TiO2纳米复合粒子, 通过TEM、UV-Vis光谱和XRD表征了不同TiO2浓度下Ag/TiO2纳米复合粒子的结构和光学性质. UV-Vis光谱证明了银颗粒的存在, 且复合粒子中的银粒径随着TiO2含量的增加而增加, 同时随着TiO2浓度的增加, 银的吸收峰出现明显的增强和展宽；从TEM照片 发现, Ag/TiO2纳米复合粒子是一种以Ag为核, 外面包覆一层TiO2的核-壳结构, TiO2浓度和Ag+浓度的增加, 使得复合粒子的银颗粒粒径增大. 用Z-扫描技术, 以锁模Ti:sapphire飞秒激光器发出的脉宽为130 fs激光做光源, 在790 nm波长的光作用下, 研究了0.5%(w)Ag+含量, 不同TiO2浓度的Ag/TiO2纳米复合粒子的非线性光学特性. 结果发现, 在790 nm激光作用下, 0.25%(w)TiO2样品膜有双光子吸收和自聚焦非线性折射现象; 而当TiO2浓度为0.70%(w)时, 样品膜的非线性吸收由反饱和吸收转变为饱和吸收.     

Ag／TiO2复合纳米催化剂的制备和表征及其光催化活性

 采用光还原沉积贵金属法，制备了Ag／TiO2复合纳米催化剂．通过调节溶液的pH值控制TiO2表面负载银的形貌，利用AAS，XRD，TEM和XPS等手段对样品进行了表征．以苯胺氧化为模型反应，考察了Ag／TiO2复合纳米催化剂样品的光催化活性以及银沉积量和沉积形貌对催化剂活性的影响．结果表明，通过调控光还原沉积条件，可在平均粒径为24nm左右的TiO2颗粒上获得3nm左右均匀分散的银粒子；在TiO2上沉积适量的具有较高分散度的金属Ag，能有效提高TiO2对苯胺氧化反应的光催化活性．     

Pinning mass-selected Agn clusters on the TiO2(110)-1x1 surface via deposition at high kinetic energy

We present the first scanning tunneling microscopy (STM) study of the deposition of mass-selected silver clusters (Ag(n),n=1, 2, 3) on a rutile TiO(2)(110)-1x1 surface at room temperature under hard-landing conditions. Under hard-landing conditions, only small features are observed on the surface in all cases without sintering or surface damage. This suggests that the high impact energy of the clusters mainly dissipates as thermal energy in the substrate, resulting in the recovery of any initial impact-induced surface damage and the formation of bound clusters on the surface near the impact point. STM images indicate that Ag(1) binds on the bridging oxygen rows twice as often as on the Ti rows. Density-functional Theory (DFT) calculations are consistent with Ag(1) binding at either bridging oxygen vacancies or with two adjacent bridging oxygen atoms in the same bridging oxygen row. STM images of Ag(2) and Ag(3) depositions indicate almost exclusive binding centered on the Ti-atom rows. DFT calculations suggest that the Ag(2) and Ag(3) clusters are bound between two bridging oxygen rows, which is consistent with the STM observations.     

含类立方烷银(Ⅰ)簇的光致蓝光配位聚合物的原位溶剂热合成

A blue photoluminescent coordination polymer [Ag₄Cl₄(dppe)₂]_n has been prepared solvothermally and characterized structurally. The crystal structure was determined by single-crystal X-ray diffraction. The crystal is of tetragonal, space group I4₁/a, a=b=1.936 03(6) nm, c=1.465 63(8) nm, V=5.493 5(4) nm³, Z=4, D_calcd=1.657 Mg·m^-3, μ=1.749 mm^-1. Reflections collected: 17 147, independent reflections: 3 247, R_int=0.021 1. Final R indices [I> 2σ(I)]: R₁=0.044 8, wR₂=0.111 0. The structure of [Ag₄Cl₄(dppe)₂]_n is a 3D-diamond highly symmetrical polymeric network containing Ag₄Cl₄ cubane-like clusters connected by 1,2-bis(diphenylphosphino)ethane (dppe). Each Ag₄Cl₄ cluster is composed of four silver and four chlorine atoms situated at alternate vertexes of a highly distorted cube with each silver atom being further coordinated to one phosphorus atom from a dppe ligand. The stripping of chloride ions from CHCl₃ provides the source for chlorine in the formation of Ag(Ⅰ) clusters. In addition, the emission spectrum of the complex 1 in solid state has been studied. CCDC: 288080.     

Photodeposition of Ag2S quantum dots and application to photoelectrochemical cells for hydrogen production under simulated sunlight

UV light irradiation of TiO(2) (λ > 320 nm) in a mixed solution of AgNO(3) and S(8) has led to the formation of Ag(2)S quantum dots (QDs) on TiO(2), while Ag nanoparticles (NPs) are photodeposited without S(8). Photoelectrochemical measurements indicated that the Ag(2)S photodeposition proceeds via the preferential reduction of Ag(+) ions to Ag(0), followed by the chemical reaction with S(8). The application of this in situ photodeposition technique to mesoporous (mp) TiO(2) nanocrystalline films coated on fluorine-doped SnO(2) (FTO) electrodes enables formation of Ag(2)S QDs (Ag(2)S/mp-TiO(2)/FTO). Ag(2)S/mp-TiO(2)/FTO has the interband transition absorption in the whole visible region, while in the spectrum of Ag/mp-TiO(2)/FTO, a localized surface plasmon resonance absorption of Ag NPs is present centered at 490 nm. Ag(2)S QD-sensitized photoelectrochemical cells using the Ag(2)S/mp-TiO(2)/FTO and Ag/mp-TiO(2)/FTO photoanodes were fabricated. Under illumination of one sun, the Ag(2)S photoanode cell yielded H(2) at a rate of 0.8 mL·h(-1) with a total conversion efficiency of 0.29%, whereas the Ag/mp-TiO(2)/FTO photoanode is inactive.     

水热法合成多孔Ag_2S敏化二氧化钛催化剂及其可见光催化活性(英文)

Porous Ag2S sensitized TiO2 catalysts were synthesized by the hydrothermal process.The crystallization and porous structure of the Ag2S/TiO2 composite photocatalysts were investigated by X-ray diffraction,scanning electron microscopy with energy dispersive X-ray analysis,UV-Vis diffuse reflectance spectroscopy,and N2 adsorption.The Ag2S/TiO2 composites were mainly composed of anatase TiO2 and acanthite Ag2S.The absorption edge wavelengths of TiO2 and the Ag2S/TiO2 composite prepared with 3 mmol Na2S.5H2O were 400 and 800 nm,respectively,that is,the absorption edge of the composite had a pronounced red shift.The photocatalytic activity under visible light was investigated by the degradation of methylene blue with a UV-Vis spectrophotometer.The photocatalytic activities under visible light of the Ag2S/TiO2 photocatalysts were much higher than that of TiO2.     

Preparation of highly uniform Ag/TiO2 and Au/TiO2 supported nanoparticle catalysts by photodeposition

Photodeposition of Ag nanoparticles on commercial TiO2 particles and nanoparticles was performed in order to provide direct visualization of the spatial distribution of photoactive sites on sub-micrometer-scale and nanoscale TiO2 particle surfaces and to create materials for potential catalytic applications. HRTEM (high-resolution transmission electron microscopy) and HAADF-STEM (high-angle annular dark-field scanning transmission electron microscopy) were used to characterize these materials. The size and spatial distributions of the Ag nanoparticles on the commercial TiO2 were not uniform; the concentration of Ag was higher on grain boundaries and at the edges of these submicrometer particles. In the case of TiO2 nanoparticles, the size distribution of the Ag nanoparticles deposited was relatively uniform and independent of irradiation time and photon energy. The amount of Ag deposited on TiO2 nanoparticles was at least 6 times higher than that on the commercial samples for comparable irradiation conditions. Compared to the case of Ag photodeposition, the difference in the amount of Au photodeposited on TiO2 particles and nanoparticles was even greater, especially at low precursor concentrations. Photodeposition on TiO2 nanoparticles is suggested as a potential method for the preparation of Au/TiO2 catalysts, as loadings in excess of 10 wt % of uniform 1 nm metal particles were achieved in this work.     

Ag-TiO2纳米催化剂的制备、表征及环氧化催化性能

环氧化合物是一类重要的有机合成中间体。工业上环氧乙烷是以Ａｇ ＳｒＯ ＣａＯ作催化剂 ,通过多相催化由乙烯和氧气氧化得到 ,其它的Ｃ2以上烯烃不能用该法生产 ,因为反应温度高 ,选择性很差。高温下的银催化乙烯的分子氧环氧化 ,选择性高于 80 % ,而用于丙烯的环氧化时 ,选择性大大降低[1] ,银多相催化分子氧环氧化烯烃的研究较活跃[2 5] 。本文合成了Ａｇ ＴｉＯ2 纳米催化剂 ,对其进行了表征 ,并初步研究了其环氧化催化性能。1　实验部分1 .1　仪器药品ＴｅｓｔｓｃａｎＳｈｉｍａｄｚｕＦＴＩＲ 80 0 0ｓｅｒｉｅｓ红外光谱仪 (ＫＢ…     

Halide coordination to zinc porphyrin sensitizers anchored to nanocrystalline TiO2

The coordination of halide ions to 5-(3,5-dicarboxyphenyl)-10,15,20-tri- p-tolylporphinatozinc(II) anchored to mesoporous nanocrystalline (anatase) TiO 2 thin films (TiO 2/ZnP) immersed in propylene carbonate was quantified. The addition of tetrabutylammonium halide salts to the external propylene carbonate electrolyte resulted in a red shift in the absorption spectrum with the maintenance of five isosbestic points. The absorption spectra were within experimental error the same for ZnP and ZnP-X (-) compared to TiO 2/ZnP and TiO 2/ZnP-X (-): A SoretZnP = 427 nm (epsilon = 574 000 M (-1) cm (-1)), A SoretZnP-Cl (-) = 435 nm (epsilon = 905 000 +/- 12 000 M (-1) cm (-1)), A SoretZnP-Br (-) = 436 nm (epsilon = 776 000 +/- 30 000 M (-1) cm (-1)), and A SoretZnP-I (-) = 437 nm (epsilon = 620 000 +/- 56 000 M (-1) cm (-1)). Titration studies with the halides revealed sharp isosbestic points consistent with formation of a 1:1 halide/porphyrin adduct. Equilibrium constants for ZnP were found to be 1670 M (-1) for Cl (-), 96 M (-1) for Br (-), and 5.5 M (-1) for I (-), and the corresponding values for TiO 2/ZnP were significantly smaller, 780 M (-1), 70 M (-1) and 3.4 M (-1). A quasi-reversible wave was observed by cyclic voltammetry of TiO 2/ZnP, E 1/2(ZnP (+/0)) = +790 mV vs Ag/AgCl, that was shifted 160 mV after addition of excess chloride, E 1/2(ZnP-Cl (0/-)) = +630 mV. In regenerative solar cells with quinone/hydroquinone redox mediators, TiO 2/ZnP and TiO 2/ZnP-X (-), where X is Cl, Br, or I, were found to convert light into electrical power. The photocurrent action spectrum demonstrated that energy conversion was initiated by light absorption of ZnP and/or the halide adduct.     

Charge separation and catalytic activity of Ag@TiO2 core-shell composite clusters under UV-irradiation

Photocatalytic properties of Ag@TiO2 composite clusters have been investigated using steady state and laser pulse excitations. Photoexcitation of TiO2 shell results in accumulation of the electrons in the Ag core as evidenced from the shift in the surface plasmon band from 460 to 420 nm. The stored electrons are discharged when an electron acceptor such as O2, thionine, or C60 is introduced into the system. Charge equilibration with redox couple such as C60/C60*- shows the ability of these core shell structures to carry out photocatalytic reduction reactions. The charge separation, charge storage, and interfacial charge-transfer steps that follow excitation of the TiO2 shell are discussed.     

理论研究Ag/MPH/TiO2体系的SERS光谱化学增强机理

采用密度泛函理论研究了Ag/对巯基苯酚(MPH)/TiO₂体系的表面增强拉曼散射(SERS)光谱化学增强机理. 分别研究了Ag₁₃/MPH和Ag₁₃/MPH/TiO₂复合物在514.5 nm激发波长下的拉曼光谱, 发现由于TiO₂的引入, 发生了非完全对称振动模式峰选择性增强的现象. 通过对电荷转移复合物基态和激发态的指认, 发现当激发波长大于MPH-TiO₂电荷转移复合物的光学吸收阈值(635 nm)时, 该体系内将发生从Ag到MPH-TiO₂部分的光诱导电荷转移现象. SERS光谱中b₂模式的选择性增强, 来源于相应振动模式与电荷转移跃迁的耦合(Herzberg-Teller机制). 我们的理论结果不仅支持了实验现象, 并且明确界定了电荷转移复合物, 对于该体系存在的光依赖SERS现象提供了一个清晰的理论阐述.     

Size-dependence of Fermi energy of gold nanoparticles loaded on titanium(iv) dioxide at photostationary state

TiO(2) particle-supported Au nanoparticles (NPs) with varying sizes and good contact (Au/TiO(2)) were prepared under a constant loading amount by the deposition-precipitation method. The Fermi energy of Au NPs loaded on TiO(2) at the photostationary state (E(F)') was determined in water by the use of S/S(2-) having specific interaction with Au as a redox probe. The E(F)' value goes up as the mean size of Au NPs (d) increases at 3.0 相似文献   

Excited state interfacial electron transfer from a compound with a single pyridine ligand

The coordination compound Ru(NH(3))(5)(eina)(PF(6))(2), where eina is ethyl isonicotinate, was synthesized and attached to optically transparent nanocrystalline (anatase) TiO(2) films, abbreviated Ru(NH(3))(5)(eina)/TiO(2). The metal-to-ligand-charge-transfer (MLCT) absorption was found to shift in wavelength with solvent. The absorption maximum of the low energy MLCT band was observed at 486 nm in acetonitrile and 528 nm in dimethylformamide for Ru(NH(3))(5)(eina)(PF(6))(2) and at 512 and 555 nm for Ru(NH(3))(5)(eina)/TiO(2), respectively. The compound was found to be nonemissive with an excited state lifetime <10 ns under all conditions studied. Light excitation in fluid solution and when attached to insulating ZrO(2) films resulted in a loss of the MLCT absorption, consistent with ligand field photochemistry. Pulsed light excitation of Ru(NH(3))(5)(eina)/TiO(2) yields an absorption difference spectrum consistent with an interfacial charge separated state, Ru(III)(NH(3))(5)(eina)/TiO(2)(e(-)). This state forms within 10 ns and returns cleanly to ground state product within milliseconds. The injection quantum yields were determined by comparative actinometry and were found to be excitation wavelength dependent: phi(inj)(417 nm) = 0.30 +/- 0.05 and phi(inj)(532.5 nm) = 0.15 +/- 0.03. Regenerative solar cells based on Ru(NH(3))(5)(eina)/TiO(2) with 0.5 M TBAI, where TBA is tetrabutylammonium, and 0.05 M I(2) in acetonitrile were very inefficient. Sluggish iodide oxidation is expected, on the basis of the negative E degrees (Ru(III/II)) = +0.17 (V vs Ag/AgCl) reduction potential, and this presumably allows a greater fraction of the injected electrons to recombine with the oxidized compound thereby lowering the solar cell efficiency.     

Making the golden connection: reversible mechanochemical and vapochemical switching of luminescence from bimetallic gold-silver clusters associated through aurophilic interactions

Aiming at the development of new architectures within the context of the quest for strongly luminescent materials with tunable emission, we utilized the propensity of the robust bimetallic clusters [Au?Ag?(R(I)/R(II))?] (R(I) = 4-C?F?I, R(II) = 2-C?F?I) for self-assembly through aurophilic interactions. With a de novo approach that combines the coordination and halogen-bonding potential of aromatic heteroperhalogenated ligands, we have generated a family of remarkably luminescent bimetallic materials that provide grounds to address the relevance, relative effects, and synergistic action of the two interactions in the underlying photophysics. By polymerizing the green-emitting (λ(max)(em) = 540 nm) monomer [Au?Ag?R(II)?(tfa)?]2? (tfa = trifluoroacetate) to a red-emitting (λ(max)(em) = 660 nm) polymer [Au?Ag?R(II)?(MeCN)?](n), we demonstrate herein that the degree of cluster association in these materials can be effectively and reversibly switched simply by applying mechanochemical and/or vapochemical stimuli in the solid state as well as by solvatochemistry in solution, the reactions being coincident with a dramatic switching of the intense, readily perceptible photoluminescence. We demonstrate that the key event in the related equilibrium is the evolution of a metastable yellow emitter (λ(max)(em) = 580 nm) for which the structure determination in the case of the ligand R(II) revealed a dimeric nonsolvated topology [Au?Ag?R(II)?]?. Taken together, these results reveal a two-stage scenario for the aurophilic-driven self-assembly of the bimetallic clusters [Au?Ag?(R(I)/R(II))?]: (1) initial association of the green-emitting monomers to form metastable yellow-emitting dimers and desolvation followed by (2) resolvation of the dimers and their self-assembly to form a red-emitting linear architecture with delocalized frontier orbitals and a reduced energy gap. The green emission from [Au?Ag?R(II)?(tfa)?]2? (λ(max)(em) = 540 nm) exceeds the highest energy observed for [Au?Ag?]-based structures to date, thereby expanding the spectral slice for emission from related structures beyond 140 nm, from the green region to the deep-red region.     

Phase structure and luminescence properties of Eu3+-doped TiO2 nanocrystals synthesized by Ar/O2 radio frequency thermal plasma oxidation of liquid precursor mists

Eu3+-doped TiO2 luminescent nanocrystals have been synthesized in this work via Ar/O2 thermal plasma oxidizing mists of liquid precursors containing titanium tetra-n-butoxide and europium(III) nitrate, with varied O2 input in the plasma sheath (10-90 L/min) and Eu3+ addition in the precursor solution (Eu/(Ti + Eu) = 0-5 atom%). The resultant nanopowders are mixtures of the anatase (30-36 nm) and rutile (64-83 nm) polymorphs in the studied range, but the rutile fraction increases steadily at a higher Eu3+ addition, as revealed by X-ray diffraction (XRD) and Raman spectroscopy, because of the creation of oxygen vacancies in the TiO2 gas clusters by substitutional Eu3+ doping. The amount of Eu3+ that can be doped into a TiO2 lattice was limited up to 0.5 atom%, above which Eu2Ti2O7 pyrochlore was formed in the final products. High resolution transmission electron microscopy (HRTEM) observation indicates that the particles are dense and have sizes ranging from several nanometers up to 180 nm. Efficient nonradiative energy transfer from the TiO2 host to Eu3+ ions, which was seldom reported in the wet-chemically derived nanoparticles or thin films of the current system, was confirmed by combined studies of excitation, UV-vis (ultraviolet-visible), and PL (photoluminescence) spectroscopy. As a consequence of this, bright red emissions were observed from the plasma-generated nanopowders either by exciting the TiO2 host with UV light shorter than 405 nm or by directly exciting Eu3+ at a wavelength beyond the absorption edge (405 nm) of TiO2.