Strain compensated Si/SiGe quantum well and quantum cascade on Si0.5Ge0.5 pseudosubstrate

This study follows up our previous investigation of the valence band (VB) intersubband emission from quantum cascade structures grown lattice matched on Si substrates. Here, Si/Si_1−xGe_x (x=80%) heterostructures are investigated which are deposited by MBE on a virtual substrate of relaxed SiGe containing 50% of Ge. TEM analysis reveal flat and abrupt interfaces for structures grown at temperatures T_growth≈300°C. Intersubband absorption and photoluminescence emission manifest well-defined interfaces and good material quality. The observed intersubband line positions are found to be in good agreement with k·p model calculations for the VB. This is in contrast to the observed type II no phonons recombination which is found at consistently lower energy than expected. Finally, electrically excited intersubband emission from a strain compensated cascade structure containing three periods is presented.     

Effect of annealing on the nanoscratch behavior of multilayer Si0.8Ge0.2/Si films

In this study, we examined the nanoscratch behavior of annealed multilayered silicon-germanium (SiGe) films comprising alternating sublayers (Si) deposited using an ultrahigh-vacuum chemical vapor deposition (UHV/CVD) system. Annealing consisted of ex situ thermal treatment in a furnace system. We used a nanoscratch technique to investigate the nanotribological behavior of the SiGe films and atomic force microscopy (AFM) to observe deformation phenomena. Our AFM morphological studies of the SiGe films revealed that pile-up phenomena occurred on both sides of each scratch. The scratched surfaces of the SiGe films that had been subjected to various annealing conditions exhibited significantly different features, it is conjectured that cracking dominates in the case of SiGe films while ploughing dominates during the scratching process. We obtained higher coefficients of friction (μ) when the ramped force was set at 6000 μN, rather than 2000 μN, suggesting that annealing of SiGe films leads to higher shear resistance; annealing treatment not only produced misfit dislocations in the form of a significantly wavy sliding surface but also promoted scratching resistance.     

Combined spectroscopy and microscopy of supported MoS2 nanoparticles

Supported molybdenum-sulfide nanoparticles are known catalysts for petroleum hydrodesulfurization as well as for electrochemical hydrogen evolution. In this study, we investigate molybdenum-sulfide nanoparticles supported on Au(1 1 1) using X-ray photoelectron spectroscopy (XPS) and scanning tunneling microscopy (STM), aiming to correlate spectroscopically determined chemical states with atomically resolved nanostructure. The results of this study allow us to conclude the following: (1) the XPS results from our model system are in good agreement with previously published results on supported MoS₂ for industrial applications, validating in part the fidelity of the model system; (2) STM reveals that catalytically active, crystalline MoS₂ nanoparticles exhibiting the well-known metallic edge state are only present after a post-deposition annealing step in the synthesis procedure, without which the particles exhibit amorphous shapes and incomplete sulfidation; and (3) the sulfided nanoparticles are found to be stable in air at room temperature.     

Manipulating Ge quantum dots on ultrathin SixGe1−x oxide films using scanning tunneling microscope tips

Germanium quantum dots (QDs) were extracted from ultrathin Si_xGe_1−x oxide films using scanning tunneling microscope (STM) tips. The extraction was most efficiently performed at a positive sample bias voltage of +5.0 V. The tunneling current dependence of the extraction efficiency was explained by the electric field evaporation transfer mechanism for positive Ge ions from QDs to STM tips. Ge QDs (∼7 nm) were formed and isolated spatially by extracting the surrounding Ge QDs with an ultrahigh density of >10¹² cm⁻². Scanning tunneling spectroscopy of the spatially-isolated QDs revealed that QDs with an ultrahigh density are electrically-isolated from the adjacent dots.     

Thermally-induced morphological transition in WOx deposited on a ZrO2(1 0 0) substrate

A combined atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) study of tungsten oxide model catalysts is presented. The model catalysts were prepared by applying the real preparation method to a ZrO₂(1 0 0) single crystal support. AFM imaged several granular structures of scattered dimensions on the surface of ZrO₂(1 0 0) in the as prepared samples. After heating, at low loading the tungsten species rearranged into small WO_x particles strongly interacting with the substrate. At high tungsten content large WO₃ aggregates also formed. XPS analysis confirmed these changes. The estimated surface density of the interacting W-containing species closely matched that of real catalysts.     

Influence of Si substrate preparation on surface chemistry and morphology of L-CVD SnO2 thin films studied by XPS and AFM

Results of experimental studies of the influence of substrate preparation on the surface chemistry and surface morphology of the laser-assisted chemical vapour deposition (L-CVD) SnO₂ thin films are presented in this paper. The native Si(1 0 0) substrate cleaned by UHV thermal annealing (TA) as well as thermally oxidized Si(1 0 0) substrate cleaned by ion bombardment (IBA) have been used as the substrates. X-ray photoemission spectroscopy (XPS) has been used for the control of surface chemistry of the substrates as well as of deposited films. Atomic force microscopy (AFM) has been used to control the surface morphology of the L-CVD SnO₂ thin films deposited on differently prepared substrates. Our XPS shows that the L-CVD SnO₂ thin films deposited on thermally oxidized Si(1 0 0) substrate after cleaning with ion bombardment exhibit the same stoichiometry, i.e. ratio [O]/[Sn] = 1.30 as that of the layers deposited on Si(1 0 0) substrate previously cleaned by UHV prolonged heating. AFM shows that L-CVD SnO₂ thin films deposited on thermally oxidized Si(1 0 0) substrate after cleaning with ion bombardment exhibit evidently increasing rough surface topography with respect to roughness, grain size range and maximum grain height as the L-CVD SnO₂ thin films deposited on atomically clean Si substrate at the same surface chemistry (nonstoichiometry) reflect the higher substrate roughness after cleaning with ion bombardment.     

Quantitative measurements of Ge surface segregation during SiGe alloy growth

Ge segregation during the growth of Si_{1 − x}Ge_x alloys (x = 5, 10, 20, and 40%) was studied using X-ray photoelectron spectroscopy. The alloys were grown in thicknesses up to 20.0 nm at 500°C to measure quantitatively the amount of segregated surface Ge. The length of alloy needed to reach steady-state growth edge was found to decrease with increasing alloy concentration (4.8, 2.8, 2.4, and 2.0 nm, respectively). It was found that each alloy had a complete monolayer of Ge on the surface and an increasing amount of segregated Ge in the second layer (20, 55, 80, and 95%, respectively) during steady-state growth. An increase in the temperature of alloy growth (400–750°C) resulted in an increase in the leading edge of alloy growth but did not change the amount of segregated Ge during steady-state growth. We propose that film stress is responsible for the amount of Ge segregation.     

Formation of micro-crystals on the (100) surface of SrTiO3 at elevated temperatures

Droplet-like features and regularly shaped micro-crystals appear on the (100) surface of single-crystals of stoichiometric and doped SrTiO₃ as a result of heat treatment around 1000–1100°C under ambient pressure. Secondary ion mass spectrometry, atomic force microscopy and X-ray photoemission are employed to characterize the morphology of the modified surface. The results provide evidence of an accumulation of SrO_x on the surface in a liquid form and subsequent recrystallization as SrO on prolonged annealing. The phenomena are discussed in relation to the restructuring in the near-surface region and the loss of material at the temperatures employed, as evident from thermogravimetrical measurements.     

MBE fabrication of self-assembled Si and metal nanostructures on Si surfaces

Two types of fairly regular distributions of Si nanostructures, of interest as templates to grow spatially controlled ensembles of metal (Co, Fe, Ag, etc.) nanostructures, are presented in this paper. Both of them are achieved by self-assembling processes during Si homoepitaxy. One corresponds to films grown by molecular beam epitaxy (MBE) on Si(0 0 1)-2 × 1 surfaces with low (<1°) miscut angles. In this case, arrays of 3D Si-islands displaying well defined pyramid-like shapes can be obtained, as evidenced by Scanning Force Microscopy (SFM) and Scanning Transmission Electron Microscopy (STEM). Such arrays exhibit strong similarities with those reported for Ge and SiGe islands on Si(0 0 1), and may thus serve as a simpler route to produce ordered distributions of metallic nanodots. On the other hand, on Si(1 1 1)-7 × 7 vicinal substrates misoriented 4° toward the direction, step rearrangement during homoepitaxy permits to produce nanopatterned surfaces, the building-blocks of which are triangular (1 1 1) platforms, with lateral dimensions of hundreds of nanometers, bound by step bunches about 30 nm high. Furthermore, different Ag deposition experiments support this spontaneous patterning on Si(1 1 1) as a promising approach to achieve regular distributions of metallic nanocrystals with an overall homogeneity in sizes, shapes and spacing.     

Morphology and photoluminescence of ultrasmall size of Ge quantum dots directly grown on Si(0 0 1) substrate

High density and ultrasmall size of Ge quantum dots (QDs) have been achieved directly on Si(0 0 1) (2 × 1) reconstruction surface. Their detailed morphology was observed by atomic force microscope (AFM) and shows that small pyramids, small domes, huts, and multi-headed large domes coexist in the film grown at 400 °C, while small domes and multi-headed large domes formed at 450 °C. Their low temperature photoluminescence (PL) showed that a very strong non-phonon (NP) peak with a large blue shift of 0.19 eV at 14 K, which can be attributed to their very high areal density, 5.2 × 10¹¹ cm⁻², and sub-10-nm mean size, 7.6 ± 2.3 nm.     

Non-contact AFM images of a C60 molecule adsorbed on the Si(0 0 1) surface: An ab initio method

A theoretical non-contact atomic force microscope (nc-AFM) image is simulated for an individual C₆₀ molecule adsorbed on the clean Si(0 0 1) surface. The ability to identify the intramolecular features of the molecule though nc-AFM imaging would allow many of the different configurations the molecule may take when adsorbed, to be identified. This would be an important preliminary step in the manipulation of the molecule along the surface, as the initial configuration that the molecule is in will affect the periodicity of the tip trajectory during the manipulation event (see D.L. Keeling et al., Phys. Rev. Lett. 94 (2005) #146104). Presented in this paper are simulated images and force curves above important sites for key stable configurations of the C₆₀ molecule. It is shown that in principle it is possible to distinguish between the different configurations of the molecule using nc-AFM. An ab initio DFT method was used to accurately describe the chemical interaction between the adsorbate and the Si tip, which has a single dangling bond at its apex.     

Vapour phase formation of amino functionalised Si3N4 surfaces

Self-assembled monolayer (SAM) formation of silanes on SiO₂ surfaces has been extensively studied. However, SAMs formed on silicon nitride (Si₃N₄) substrates have not been explored to the same level as SiO₂, even though they are of technological interest with a view to the chemical modification of microelectromechanical systems (MEMS). Therefore, this article presents the formation and characterisation of 3-aminopropyltrimethoxysilane (APTMS) SAMs on Si₃N₄ substrates from solution phase and vapour phase, compared to the well characterised APTMS SAMs formed on SiO₂ surfaces. Contact angle, atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and ellipsometric data indicate the formation of APTMS SAMs (0.55 nm ellipsometric thickness) after 60 min immersion of either SiO₂ or Si₃N₄ substrates in APTMS solution (0.5 mM in EtOH). By comparison Si₃N₄ substrates exposed to APTMS vapour, at 168 mbar for 60 min, result in the formation of the equivalent of a bi or trilayer of APTMS.     

STM investigations of Au(1 1 1) electrodes coated with vitamin B12 derivatives

Vitamin B₁₂ derivatives immobilized at flame-annealed Au(1 1 1) electrode surfaces have been investigated in close correlation with their structural properties and spatial arrangement at the electrode substrate by scanning tunneling microscopy (STM) in air and in aqueous 0.1 M NaClO₄ solution. The investigated compounds were symmetrical (B₁₂C₁₀S-SC₁₀B₁₂) and nonsymmetrical (B₁₂C₁₀S-SC₁₀) dialkyl disulfide derivatives of vitamin B₁₂, attached to the electrode surfaces by the S-Au bond. The ex situ and in situ STM experiments show the formation of a surface layer, whose packing density and structure is presumably controlled by the spatial arrangement of the large cobyrinate head groups. In presence of the symmetrical B₁₂ compound, a disordered surface layer is observed. Voltammetric investigations show that, in 0.1 M NaClO₄, this layer becomes unstable at potentials approximately ? −1000 mV vs. MSE and is almost completely removed at more negative potentials. The STM imaging properties of the nonsymmetrical B₁₂ surface layer show a significant dependence on the tunneling distance. In particular, at small tunneling distances, a highly regular hexagonal surface pattern is observed that suggests strongly the presence of an ordered surface assembly. Modeling of the B₁₂ head group has been performed to provide information for a structure-related interpretation of the high-resolution STM images. The investigations are first STM results obtained at such B₁₂ modified electrodes.     

Impact of 100 MeV Au on the surface of relaxed Si0.5Ge0.5 alloy films studied by atomic force microscopy

We demonstrate a gradual surface modification process of relaxed Si_0.5Ge_0.5 alloy films by 100 MeV Au beam with fluence varying between 5 × 10¹⁰ and 1 × 10¹² ions/cm² at 80 K by means of atomic force microscopy (AFM). Presence of Ge quantum dots (QDs) was found in the virgin sample. The disappearance of the QDs were noticed when the samples were irradiated with a fluence of 5 × 10¹⁰ ions/cm². Craters were found developing at a fluence of 1 × 10¹¹ ions/cm². Apart from the evolution of the craters, blisters were also detected at a fluence of 1 × 10¹² ions/cm². Variation of the average root mean square value of the surface roughness as a function of fluence was examined.     

Si衬底上生长的MnSi薄膜和MnSi1．7纳米线的STM和XPS分析

本文采用分子束外延方法制备出MnSi薄膜和MnSi1．7纳米线,利用扫描隧道显微镜进行观察,采用X射线光电子能谱仪系统地分析了MnSi薄膜和MnSi1．7纳米线的Mn2p和Si2p．结果表明厚度为-0．9nm的MnSi薄膜表面为／3×／3重构,MnSi1．7纳米线长50ff--1500nm,宽16—18nm,高-3nm．MnSi薄膜的Mn2p1／2和Mn2p3／2峰位与MnSil．7纳米线相同,均分别为649．7eV和638．7ev结合能在640-645eV和-653．8eV处的锰氧化合物的Mn2ps／2和Mn2p1／2峰证明在短暂暴露于空气中后MnSi薄膜和MnSi1．7纳米线表面有氧化层形成．相对于纯si的si2p谱,两种锰硅化合物的Si2p谱向低结合能方向发生了位移,表明随着锰硅化合物的形成Si的化学环境发生了变化．     

Germanium growth on Br-terminated Si(1 0 0)

The consequences of Ge deposition on Br-terminated Si(1 0 0) were studied with scanning tunneling microscopy at ambient temperature after annealing at 650 K. One monolayer of Br was sufficient to prevent the formation of Ge huts beyond the critical thickness of 3 ML. This is possible because Br acts as a surfactant whose presence lowered the diffusivity of Ge adatoms. Hindered mobility was manifest at low coverage through the formation of short Ge chains. Further deposition resulted in the extension and connection of the Ge chains and gave rise to the buildup of incomplete layers. The deposition of 7 ML of Ge resulted in a rough surface characterized by irregularly shaped clusters. A short 800 K anneal desorbed the Br and allowed Ge atoms to reorganize into the more energetically favorable “hut” structures produced by conventional Ge overlayer growth on Si(1 0 0).     

Observing the effect of water vapor on post-irradiated surface morphology of SiO2 and Si3N4 insulators by atomic force microscopy

In this work, we investigated the effect of water-vapor treatment on the surface morphology of SiO₂ and Si₃N₄ insulators before and after Co⁶⁰ gamma-ray irradiation by using the atomic force microscopy (AFM) operated under non-contact mode. Before irradiation, no apparent surface morphology change was found in SiO₂ samples even they were water vapor treated. However, bright spots were found on post-irradiated water-vapor-treated SiO₂ sample surfaces but not on those without water-vapor treatment. We attributed the bright spots to the negative charge accumulation in the oxide due to charge balancing between hydroxyl (OH⁻) ions adsorbed on SiO₂ surface and electron-hole pairs (ehps) generated during irradiation since they can be annealed out after low temperature annealing process. On the contrary, no bright spots were observed on post-irradiated Si₃N₄ samples with and without water-vapor treatment. This result confirms that Si₃N₄ is a better water-resist passivation layer than SiO₂ layer.     

Surface analysis for LiBq4 growing on ITO and CuPc film using atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS)

We have investigated the morphology and surface electron states of LiBq₄ deposited on ITO and CuPc/ITO, using atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The AFM observations indicate that LiBq₄ can form a much more uniform film on CuPc than that on ITO. Furthermore, X-ray photoelectron spectroscopy (XPS) is utilized to further demonstrate the AFM results. From the analysis of XPS, we found that LiBq₄ molecules have poor thermal stability, they are seriously oxidized during depositing; but when a CuPc layer is inserted between LiBq₄ and ITO film, the oxidation and surface contamination of LiBq₄ are significantly reduced. It is then concluded that the introduction of a CuPc buffer layer under the LiBq₄ film can improve the film quality of LiBq₄.The XPS results also testified the fact that no coordination bonds between N atoms and B atoms are formed in LiBq₄ molecules, which make LiBq₄ to be potential blue organic light-emitting material.     

Ge quantum dots growth on nanopatterned Si(0 0 1) surface: Morphology and stress relaxation study

The self-organized growth of germanium quantum dots on square nanopatterned Si(0 0 1) substrates is investigated by scanning tunnelling microscopy (STM) and grazing incidence X-ray diffraction (GIXRD) techniques. A regular surface patterning in the 10-100 nm period range is obtained by etching an interface dislocation network obtained by the controlled molecular bonding of Si substrates. The depth of the silicon surface profile is increased by a double etching process. Growth experiments are performed by solid source molecular beam epitaxy (MBE), and for deep trenches, germanium growth conditions are optimized to obtain one Ge dot per Si mesa. It is shown that the trench depth and the mesa profile strongly affect the dot size and its coincidence with the initial regular surface network. Anomalous GIXRD measurements are performed to highlight the Ge elastic relaxation and intermixing during heteroepitaxial growth. We report a significant modification in the stress state of Ge dots as a function of thermal annealing after growth.     

Halogen chemisorption, the pairwise diffusion of I, and trapping by defects on Si(1 0 0)

Halogen molecules dissociatively chemisorb on Si(1 0 0)-(2 × 1), and the bonding structures that they adopt can be elucidated with scanning tunneling microscopy. Of the Cl, Br, and I group, Cl has the highest single atom diffusion barrier, and both single and paired adatoms are observed at 295 K. The barrier is smaller for Br, and the adatoms can interrogate the surface until they form pairs, which are then immobile, or are trapped at C-type defects. The barrier is smallest for I, allowing the formation of pairs and trapped states, but the pairs are mobile at ambient temperature. Their motion is thermally activated, the events are random, and the diffusivities along and across the dimer row are ∼0.42 and ∼0.17 Å²/s at 295 K. The respective energy barriers for pairwise diffusion are ∼0.76 and ∼0.82 eV, assuming an attempt frequency of 10¹² s⁻¹. Studies over long times reveal that pairwise diffusion at low coverage is ultimately quenched by the increasing density of C-type defects, i.e. the increasing amounts of dissociated H₂O.